petroleum engineering 406 lesson 4 well control. read well control manual –chapter 9 homework 2...
TRANSCRIPT
Petroleum Engineering 406
Lesson 4
Well Control
Read
• Well Control Manual– Chapter 9
• Homework 2 Due Feb. 3, 1999
Content
• Development of Abnormal Pressure
• Properties of Normally Pressured Formations
• Properties of Abnormally Pressured Formations
• Casing Seat Selection
Knowledge of Pore and Fracture Pressures Leads to:
• More effective well planning
• Maximize penetration rates with balanced drilling
• Safer and more economical selection of casing points
• Minimize trouble due to lost circulation and kicks
Knowledge of Pore and Fracture Pressures Leads to:
• Better engineered production and test equipment
• Better understanding of local geology and drilling hazards
• More accurate analysis of drilling data and electric logs
Normally Pressured Formation
Fluids Squeezed out with compaction
Abnormal Formation Pressures
• Due to:– Incomplete compaction– Diagenesis– Differential Density in Dipping Formations– Fluid Migration– Tectonic Movement– Aquifers– Thermal Effects
Incomplete compaction
Fluids trapped in place
Fluids begin to support overburden
Diagenesis
• At 200oF to 300oF Clays undergo chemical alteration. Montmorillonite clays dehydrate and release some of the bound water into the space already occupied by free water, increasing pressure
Differential Density in Dipping Formations
Fluid Migration
Tectonic Movement - Uplifting
Tectonic Movement - Faulting
Aquifers
Thermal Effects
• Theories– Increased temperature with depth and chemical
reactions cause increased pressures– Increased pressures caused increased
temperatures
Salt Formations
Depth
Pressure Gradient
Pore press. gradient
Overburden gradient
Salt formation
Shale Properties used to Predict Pore Pressures
• Shales are used because:– Most pressure transition zones occur in
relatively thick shales– Properties of clean shales are fairly
homogeneous at any depth, and can be predicted with some degree of accuracy.
Shale Properties used to Predict Pore Pressures
• Shales are used because:– A deviation from the expected can be
interpreted as a change in pressure gradient– Detecting these deviations in low permeability
shales gives an early warning prior to drilling into pressured permeable formations, thus avoiding kicks.
Normally Pressured Shales
• Porosity - Decreases with depth
• Density - Increases with depth
• Conductivity - Decreases with depth
• Resistivity - Increases with depth
• Sonic travel time - Decreases with depth
• Temp. gradient - Relatively constant
Abnormally Pressured Shales
• Porosity - Higher than expected
• Density - Lower than expected
• Conductivity - Higher than expected
• Resistivity - Lower than expected
• Sonic travel time - Higher than expected
• Temp gradient - Increases
Porosity Density Conductivity Sonic
Shale Density
Temperature gradient - Increases
Depth
Temperature
Normal Trend
Top of Geo-pressure
Pore Pressure Prediction Occurs:
• Prior to drilling
• During drilling
• After drilling
Before Drilling
• Offset mud records, drilling reports, bit records, well tests
• Geological Correlation
Before Drilling
• Open Hole Logs from offset wells
Before Drilling
• Seismic data
During Drilling
• Kick - SIDPP and HSP in DP can give accurate measurement of formation pore pressure
• LOT - gives accurate measurement of fracture pressure
During Drilling
• Correlation of penetration rate to offset logs
• Changes in shale penetration rate
During Drilling
• Shale density Change– Mercury pump– Mud balance
• Fill mud balance with clean shale until it balances at 8.33 ppg
• Fill the balance cup with water and determine total weight
• Calculate shale bulk density:– SBD=8.33/(16.66-Total Weight)
During Drilling
• Shale density Change - Density column
During Drilling
• Mud gas content change
During drilling
• Shale cutting change
During Drilling
• Mud chloride change
• Increase in fill on bottom
• Increase in drag or torque
• Contaminated mud
• Temperature change
During Drilling
• Abnormal trip fill-up behavior
• Periodic logging runs
• Drill-stem tests
• MWD or LWD tools
• Paleontology
During Drilling
• dc-exponent
– P=K*(W/D)d*Ne
• P=penetration rate of shale
• K=formation drillability
• W=weight on bit
• D=bit diameter
• N=rotary speed
• d=bit weight exponent
• e=rotary speed exponent
During Drillingd-exponent and dc-exponent
During Drilling
After Drilling
• Log evaluation
• Flow tests
• BHP surveys
• Shut-in pressure tests
• Analysis of mud reports, drilling reports, and bit records