phoenix multi-fit - htp · phoenix multi-fit stainless steel tank will outlast any coated steel...
TRANSCRIPT
Advanced Heating& Hot Water Systems
PhoenixMulti-FitStainless Steel, Gas fired, Commercial Water Heater
Up to 96% Thermal Efficiency
Up to 5:1 Turndown Ratio
Industry first for Condensing Water Heaters: Top and Side Connection Choices for Inlet and Outlet
Ease of Installation Extremely lightweight tank fits virtually anywhere; 100 gallon: 63” height &80 gallon: 55“ height
316L Stainless Steel Tank Eliminates the need for anode rods
Vents in Inexpensive PVC or CPVC pipe Combined vent lengths up to 200’ in 3” pipe or vent lengths up to 85’ in 2” pipe
Beautiful Stainless Steel Look
80/100 Gallon - 130k /199k Btuh
Inlet / Outlet Connections On Both The Top & Side
Phoenix Multi-Fit will accommodate even the most difficult installations with lower clearance and multiple inlet and outlet connections making it easier to replace traditional center flue heaters.
Top hot water outlet (stainless steel)
Top cold water inlet (stainless steel)
Tank constructed of 316L stainless steel
Insulated w/ water blown foam
2” thick in the side wall
w/ a rating of R14.2 - 3” thick in the top
w/ a rating of R21.3
Factory installed ASME rated
temperature and pressure
relief valve
Low water cutoff sensor
Lower (cold water)temperature sensor
Upper (hot water) temperature sensor
Side cold water inlet (stainless steel)
Exhaust adaptor to P VC / CPVC / PolyPro venting
Venting Options:- Direct vent side wall- Direct vent vertical- Unbalanced venting- Room air- Combined vent /air intake length up to 200ft
Proprietary heat exchanger: body constructed of 90/10 cupronickel top section constructed of 800H stainless steel
High limit safety sensor
Side hot water outlet (stainless steel)
A Closer Look Inlet / Outlet Connections On Top & Side
L aser Welded Tank An advanced laser allows for more precise welding through a concentrated heat source, producing high quality 316L stainless steel tank construction with stronger, long lasting seams.
Stainless steel burner - 120 volt motor w/
wave modulation control
Condensate trap assembly
Components located on front of heater for
easy service access, all related hardware is made of stainless steel
studs and brass nuts
Digital LED display system monitoring
and temperature adjustment
Why Choose A Stainless Steel Tank?Because They Are Built To L ast!
All coated tanks require anodes to delay inevitable corrosion and tank failure. The average commercial water heater lasts about 6 years. The Phoenix Multi-Fit stainless steel tank will outlast any coated steel tank in the market.
The Advantages
Prolongs Tank LifeNo Need for Anode Rods
Light Weight ConstructionEliminates Scale Build-up on HX
Stainless Steel vs. Glass -Lined
HTP’s 100 GAL. Tank
230 LBS.
Top Competitor’s 100 GAL. Tank
550 LBS.
SCALE BUILD-UP
NO Anode Rods Needed!
-Durable Construction
-High Performance
-Excellent Heat Transfer Capabilities
-Self Cleaning
Stainless Steel (1.65mm thick) welded to the top of the heat exchanger where flue gas is the hottest.
Transitions to 90/10 Cupronickel (1.1mm thick) spiral design that expands and contracts rapidly with the change in temperature eliminating scale build-up.
HTP’s Unique Heat Exchanger
www.htproduc ts .com • 272 Duchaine B lvd, New Bedford, MA 02745In accordance with our company policy of ongoing product improvement, HTP Comfort Solutions LLC. reserves the right to make changes without prior notice. • MKTLIT-68 - 12 / 2017 © HTP
PhoenixMulti-Fit
Specifications
H G
N
L
O
M
COLDWATERINLET
HOTWATEROUTLET
P P
EXHAUST VENT
VALVE
AIR INTAKE
TEMP/PRESSURERELIEF VALVE
DRAIN
OUTLET
COLD WATER INLET
CONDENSATE LINE
HOT WATER
GAS LINE
J
K
UPPER TEMPSENSOR
CUT-OFFLOW WATER
HIGH LIMITSAFETY
LOWER TEMPSENSOR
A
E
B
C
D
F
H G
N
L
O
M
COLDWATERINLET
HOTWATEROUTLET
P P
EXHAUST VENT
VALVE
AIR INTAKE
TEMP/PRESSURERELIEF VALVE
DRAIN
OUTLET
COLD WATER INLET
CONDENSATE LINE
HOT WATER
GAS LINE
J
K
UPPER TEMPSENSOR
CUT-OFFLOW WATER
HIGH LIMITSAFETY
LOWER TEMPSENSOR
A
E
B
C
D
F
K
H G
N
L
O
M
COLD WATERINLET
HOT WATEROUTLET
P P
EXHAUST VENT
VALVE
AIR INTAKE
TEMP/PRESSURERELIEF VALVE
DRAIN
OUTLET
COLD WATER INLET
CONDENSATE LINE
HOT WATER
GAS LINE
J
UPPER TEMPSENSOR
CUT-OFFLOW WATER
HIGH LIMITSAFETY
LOWER TEMPSENSOR
A
E
B
C
D
F
PHOENIX MULTI FIT WATER HEATERMODEL* GAL. A B C D E F G H J K L M N O P
PHM130-80/199-80 80 27" 55" 45-1/4" 7-1/4" 27-1/2" 32" 18-1/4" 17" 3" 8" 45-1/4" 24-3/4" 38-1/4" 7-1/4" 9-1/2"
PHM130-100/199-100 100 27" 63" 54" 7-1/4" 27-1/2" 32" 18-1/4" 17" 3" 8" 54" 24-3/4" 38-1/4" 7-1/4" 9-1/2"
PHOENIX MULTI FIT WATER HEATER SPECIFICATION
MODEL* INPUT MODULATIONAIR INTAKE/
EXHAUST VENT SIZE
INLET/OUTLET
SIZE
GAS LINE
CONN.
SYSTEMRELIEF
PIPE SIZESHIPPINGWEIGHT
MAX.TEMPERATURE
LIMIT
PHM130-80 30,000 - 130,000 2" 1-1/2" NPT 3/4" 3/4" 285 LBS 160PHM199-80 40,000 - 199,000 3" 1-1/2" NPT 3/4" 3/4" 285 LBS. 160PHM130-100 30,000 - 130,000 2" 1-1/2" NPT 3/4" 3/4" 315 LBS. 160PHM199-100 40,000 - 199,000 3" 1-1/2" NPT 3/4" 3/4" 315 LBS. 160
LP-179-B11/15/18
*ALL DIMENSIONS ARE APPROXIMATE, A SUFFIX OF "LP" DENOTES PROPANE GAS
11/15/18
K
H G
N
L
O
M
COLD WATERINLET
HOT WATEROUTLET
P P
EXHAUST VENT
VALVE
AIR INTAKE
TEMP/PRESSURERELIEF VALVE
DRAIN
OUTLET
COLD WATER INLET
CONDENSATE LINE
HOT WATER
GAS LINE
J
UPPER TEMPSENSOR
CUT-OFFLOW WATER
HIGH LIMITSAFETY
LOWER TEMPSENSOR
A
E
B
C
D
F
PHOENIX MULTI FIT WATER HEATERMODEL* GAL. A B C D E F G H J K L M N O P
PHM130-80/199-80 80 27" 55" 45-1/4" 7-1/4" 27-1/2" 32" 18-1/4" 17" 3" 8" 45-1/4" 24-3/4" 38-1/4" 7-1/4" 9-1/2"
PHM130-100/199-100 100 27" 63" 54" 7-1/4" 27-1/2" 32" 18-1/4" 17" 3" 8" 54" 24-3/4" 38-1/4" 7-1/4" 9-1/2"
PHOENIX MULTI FIT WATER HEATER SPECIFICATION
MODEL* INPUT MODULATIONAIR INTAKE/
EXHAUST VENT SIZE
INLET/OUTLET
SIZE
GAS LINE
CONN.
SYSTEMRELIEF
PIPE SIZESHIPPINGWEIGHT
MAX.TEMPERATURE
LIMIT
PHM130-80 30,000 - 130,000 2" 1-1/2" NPT 3/4" 3/4" 285 LBS 160PHM199-80 40,000 - 199,000 3" 1-1/2" NPT 3/4" 3/4" 285 LBS. 160PHM130-100 30,000 - 130,000 2" 1-1/2" NPT 3/4" 3/4" 315 LBS. 160PHM199-100 40,000 - 199,000 3" 1-1/2" NPT 3/4" 3/4" 315 LBS. 160
LP-179-B11/15/18
*ALL DIMENSIONS ARE APPROXIMATE, A SUFFIX OF "LP" DENOTES PROPANE GAS
11/15/18
K
H G
N
L
O
M
COLD WATERINLET
HOT WATEROUTLET
P P
EXHAUST VENT
VALVE
AIR INTAKE
TEMP/PRESSURERELIEF VALVE
DRAIN
OUTLET
COLD WATER INLET
CONDENSATE LINE
HOT WATER
GAS LINE
J
UPPER TEMPSENSOR
CUT-OFFLOW WATER
HIGH LIMITSAFETY
LOWER TEMPSENSOR
A
E
B
C
D
F
PHOENIX MULTI FIT WATER HEATERMODEL* GAL. A B C D E F G H J K L M N O P
PHM130-80/199-80 80 27" 55" 45-1/4" 7-1/4" 27-1/2" 32" 18-1/4" 17" 3" 8" 45-1/4" 24-3/4" 38-1/4" 7-1/4" 9-1/2"
PHM130-100/199-100 100 27" 63" 54" 7-1/4" 27-1/2" 32" 18-1/4" 17" 3" 8" 54" 24-3/4" 38-1/4" 7-1/4" 9-1/2"
PHOENIX MULTI FIT WATER HEATER SPECIFICATION
MODEL* INPUT MODULATIONAIR INTAKE/
EXHAUST VENT SIZE
INLET/OUTLET
SIZE
GAS LINE
CONN.
SYSTEMRELIEF
PIPE SIZESHIPPINGWEIGHT
MAX.TEMPERATURE
LIMIT
PHM130-80 30,000 - 130,000 2" 1-1/2" NPT 3/4" 3/4" 285 LBS 160PHM199-80 40,000 - 199,000 3" 1-1/2" NPT 3/4" 3/4" 285 LBS. 160PHM130-100 30,000 - 130,000 2" 1-1/2" NPT 3/4" 3/4" 315 LBS. 160PHM199-100 40,000 - 199,000 3" 1-1/2" NPT 3/4" 3/4" 315 LBS. 160
LP-179-B11/15/18
*ALL DIMENSIONS ARE APPROXIMATE, A SUFFIX OF "LP" DENOTES PROPANE GAS
11/15/18
HTP Made In Am
erica • HTP Made In A
mer
ic
a • HTP Made In A
merica • HTP Made In
Am
eric
a •
SCAQMD Rule 1146.2