phone-page telephone signal actuator - leading distributor of

90 F ie lds tone Cour t ||||| Chesh i re , CT 06410P h : 2 0 3 . 6 9 9 . 3 3 0 0 ||||| F x : 2 0 3 . 6 9 9 . 3 1 0 8

www.edwards-s ignals.com

15-19TELEPHONE SIGNALS & ACCESSORIES

© Copyright 2004 Edwards

The Edwards 910 Phone-Page Telephone Signal Actuator interfaces

with an existing telephone to provide activation of a remote audible

or visual signaling device when the telephone rings. The signal ac-

tuation follows the ring pattern of the telephone. The remote signal

automatically turns off when the telephone is answered or the caller

hangs up. The remote signaling device is purchased separately.

See Phone Page Recommended Applications, page 15-20.

A modular telephone line connects the Phone-Page to the tele-

phone. See Phone-Page Installation & Accessories, page 15-21.

Unit plugs into a standard 120V AC wall outlet and draws power

from the line to operate the remote audible or visual signal.

Ideal for use in factories, warehouses, loading docks, and construc-

tion sites.

Phone-Page® TelephoneSignal Actuator

Ground typeplug in backof unit forconnection to120V AC outlet

Modular jack

Modular duplexplug adapter

(supplied with 910)or

Cat. No. 913 (optional)

Plugreleaselever

120V AC receptaclefor connection ofsignaling device(s)

Supplied screwfor securing unitto wall outlet

910FEATURES

> Beige housing

> Modular duplex plug adaptor

> High grade copper coils

AGENCY APPROVALS

> UL 2017 Listed

> Registered with the FCC incompliance with Part 68 of FCCRules and Regulations(No. GYX30D-19623-RG-N)

SPECIFICATIONS

> Nominal input: 120V 50/60 Hz

> Input limits: 102 -132V 50/60 Hz

> Max output load: 10 ampsresistive, 4 amps inductive, 300watts tungsten

> Standby power: 0 watts; power on:0.67 watts @ 90V

> Ring signal limits: 90V AC +/-30% @ 20 Hz @ 0.33 duty factor

> Tip to ring input impedance:11,705 ohms

> DC input resistance: infinite

> REN No: 1.0A/1.7B

D-04


www.edwards-s ignals.com15-4TELEPHONE SIGNALS & ACCESSORIES

The Edwards electro-mechanical, pressed steel, telecode relays are

designed to activate up to 5 vibrating-type horns, buzzers, and

bells. The unit's windings are rated in ohms rather than volts. Wire

size and number of turns vary with resistance requirements.

The B-8316 series relay is supplied with a capacitor; the B-8315 se-

ries is not. If a capacitor is required, order the Cat. No. B-8325 one

micro farad, 400V capacitor with bracket.

Unit mounts to any flat surface using the mounting holes on 3 3/8"

(86mm) centers. 1/2" (13mm) and 3/4" (19mm) knockouts are pro-

vided for input and output wiring.

Relays operating on AC ringing voltage and used on common bat-

tery circuits require capacitors. Relays operating on DC ringing

voltages do not require capacitors unless energized by a common

battery.

For areas where ambient noise levels are high or where personnel

are unable to be near telephones at all times such as factories,

loading docks, mines, quarries, lumber yards, gas stations, found-

ries, etc.

Ordering Information

Specify pull up coil resistance, voltage, and frequency data. For

standard phone system ringing circuits, specify same coil resis-

tance as bell ringer coils. For intercommunicating phone ringing cir-

cuits, specify relays of same voltage and frequency as ringing cir-

cuit.

MechanicalTelecode® Relays

B-8315 & B-8316 Series

Pressed Steel

FEATURES

> Long-life tungsten contacts

> Gray finish


> Hinged cover

SPECIFICATIONS

> UL 2017 Listed

> B-8316 Series is registered withthe FCC in compliance with Part68 of FCC Rules and Regulations(No. 329USA-21250-RG-N)

FEATURES

> Normally open circuit relay

> Two shading coils preventarmature chatter


D-0

4



TECHNICAL INFORMATION


DC Coil With Without WithoutResistance Capacitor Capacitor Capacitor

Cat. No. (ohms) VAC VAC VDC

B-8315-P-1000* 1000 100-115 105-115 18

B-8315-P-1600* 1600 140-170 170-200 24

B-8315-P-2500* 2500 200-230 200-230 30

B-8315-P-3000* 3000 220-277 220-277 40

B-8316-P-1000** 1000 100-115

B-8316-P-1600** 1600 140-170

B-8316-P-2500** 2500 200-230

B-8316-P-3000** 3000 220-277

*Supplied without capacitor**Supplied with 1 micro farad @ 400V capacitor

6"(152mm)

3 3/8"(86mm)

6"(152mm)

3 3/8"(86mm)

4"(102mm)


D-04



The Edwards hazardous location, electro-mechanical, telecode re-

lays are designed to activate up to 5 vibrating-type horns, buzzers,

and bells. The unit's windings are rated in ohms rather than volts.

Wire size and number of turns vary with resistance requirements.




Unit mounts to any flat surface using the mounting lugs on 6 3/4"

(171mm) centers. Use 1/2" (13mm) conduit for input and output wir-

ing.




battery.

For hazardous location areas where ambient noise levels are high

or where personnel are unable to be near telephones at all times.






cuit.


B-8319 & B-8320 Series

Hazardous Location

FEATURES


> Gray finish


> Explosion proof housing

AGENCY APPROVALS

> UL 1203 Listed for Class I,Division 1 and 2, Group D; ClassII, Division 1 and 2, Groups F andG; and Class III locations


SPECIFICATIONS




D-0

4







B-8319-P-1000* 1000 100-115 105-115 18

B-8319-P-1600* 1600 140-170 170-200 24

B-8319-P-2500* 2500 200-230 200-230 30

B-8319-P-3000* 3000 220-277 220-277 40

B-8320-P-1000** 1000 100-115

B-8320-P-1600** 1600 140-170

B-8320-P-2500** 2500 200-230

B-8320-P-3000** 3000 220-277


7"(178mm)

6 3/4"(172mm)

Mtg. Centers

5 1/8"(130mm)

4 29/32"(125mm)

1/2" IP(13mm)Tapered Tap.


D-04



The Edwards weatherproof, electro-mechanical telecode relays are

designed to activate up to 5 vibrating-type horns, buzzers, and

bells. The unit's windings are rated in ohms rather than volts. Wire

size and number of turns vary with resistance requirements.




Unit mounts to any flat surface using the mounting lugs on 6 3/4"(171mm) centers. Use 1/2" (13mm) conduit for input and output wir-ing.




battery.

For areas where ambient noise levels are high or where personnel

are unable to be near telephones at all times such as factories,

loading docks, mines, quarries, lumber yards, gas stations, found-

ries, etc.






cuit.


B-8322 & B-8323 Series

Weatherproof

FEATURES


> Gray finish


> Cast aluminum back box andcover

AGENCY APPROVALS

> UL 2017 Listed


SPECIFICATIONS




D-0

4







B-8322-P-1000* 1000 100-115 105-115 18

B-8322-P-1600* 1600 140-170 170-200 24

B-8322-P-2500* 2500 200-230 200-230 30

B-8322-P-3000* 3000 220-277 220-277 40

B-8323-P-1000** 1000 100-115

B-8323-P-1600** 2500 200-230

B-8323-P-2500** 2500 200-230

B-8323-P-3000** 3000 220-277


7"(178mm)

6 3/4"(172mm)

Mtg. Centers

5 1/8"(130mm)

4 29/32"(125mm)



D-04



www.edwards-s ignals.com6-22HORNS & SIRENS

The Edwards B-N-8546 AC and B-8526 DC Series are designed for

use where a loud and distinctive signal is needed. The sound

mechanism of the signal starts and stops instantly with current im-

pulse. The projector is connected to the heavy duty die cast alumi-

num housing by a cast aluminum, threaded ring.

Two mounting lugs are provided on either side of the unit for wall

mounting. The housing is tapped on one side for 1/2" (13mm) con-

duit to allow for field wiring installation.

Used where directional sound dispersion is required or specified.

Applications include timing, scheduling, paging, and general alarm

at construction sites, textile and paper mills, lumber yards, and

shipping docks.

AdaptaHorn® SingleProjector Horn

B-8526 & B-N-8546 Series

Weatherproof, NEMA Type 4X

FEATURES

> Convenient plug-in assembly

> Corrosion resistant heat flowedepoxy finish

> Completely assembled

> Gasket sealed

> External volume control screw

AGENCY APPROVALS

> UL Listed NEMA Type 4Xenclosure

SPECIFICATIONS

> Heavy duty die cast aluminum

> 7" (178mm) seamless steelprojector

> Vibrating diaphragm

> Tungsten contacts with arcsuppressor (B-8526)

D-0

4

HORNS & SIRENS





6-23

5 1/2"(140mm)

6 3/8"(162mm)

9 1/2"(241mm)

13/16"(21mm)

2 holes3/8" (10mm) Tap 1/2" (13mm)

5 1/8"(130mm)

DC coil dB atCat. No. Volts Amps V A Res. (Ohms) 10 Ft.

B-N-8546-E5 12V AC 1.6 19.2 3B-N-8546-G5 24V AC 1.1 26.4 5 97B-N-8546-N5 120V AC .2 24 146B-N-8546-R5 240V AC .1 24 750

B-8526-G1 24V DC 1 24 21.5 95B-8526-P1 125V DC .2 25 103B-8526-S1 250V DC .1 25 600

D-04

© 2000 EDWARDSCHESHIRE, CT 06410

www.edwards-signals.com15-10

Haza

rdou

s,N

EMA

&IP

Def

initi

ons

Visu

alSi

gnal

sBe

lls &

Buzz

ers

Elec

troni

cSi

gnal

s

Proc

ess

Cont

rol

Sign

als

Horn

s &

Sire

ns

Mes

sage

Cent

ers

&An

nunc

iato

rs

Out

door

War

ning

Sign

als

Elec

tric

Chim

es

Push

But

tons

Cont

acto

rsDo

or D

evic

esTr

ansf

orm

ers

Fire

Ala

rmEq

uipm

ent

Cloc

ksAD

A/Ho

spita

lSi

gnal

ing

Devi

ces

Tele

phon

eSi

gnal

s &

Acce

ssor

ies

Fax-on-Demand # 1217

Features• Hardwire• Injected molded enclosure• Strain relief grommets on wiring

entrances• AC or DC activating voltage

DescriptionThe Edwards B-ER-2000 ElectronicTelecode Relay is designed to activateremote extension signals such ashorns, bells, strobes, or similar de-vices. The relay is activated by theline ringing voltage of the telephone;operation of the connected signalmatches the telephone ringing cycle.The unit is designed for indoor useonly.

Agency Approvals• UL Listed• FCC Registered

Specifications• REN No: 1.5B @ > 50V; 3.4B @ < 50V• AC activation voltage: 10 - 250V• Ringing frequency: 16 to 70 Hz• DC Keying Voltage: 10 -150V• Contact rating: 5 amps at 120V AC

InstallationUnit mounts to any flat surface usingthe supplied hardware. All tele-phone, power input, and signal out-put connections are made internal tothe unit.

Edwards® B-ER-2000Electronic Telecode® Relay

5 7/8"(149mm)

2"(51mm)

3 1/8"(79mm)

ApplicationsFor areas where ambient noise levelsare high or where personnel are un-

able to be near telephones at alltimes. Recommended for factories,loading docks, assembly areas, lum-ber yards, and gas stations.





The Edwards B-ERW-2100 Electronic Telecode Relay is designed to

activate remote extension signals such as horns, bells, strobes, or

similar devices. The relay is activated by the line ringing voltage of

the telephone; operation of the connected signal matches the tele-

phone ringing cycle. The unit is designed for outdoor use.

Unit mounts to any flat surface using the supplied hardware. Use

1/2" (13mm) conduit for input and output wiring. All telephone,

power input and signal output connections are made inside the unit.

For outdoor areas where ambient noise levels are high or where per-

sonnel are unable to be near telephones at all times. Recom-

mended for factories, loading docks, assembly areas, lumber

yards, and gas stations.

ElectronicTelecode® Relay

6 3/4"(172mm)

Mtg. Centers

5 1/8"(130mm)

4 29/32"(125mm)

7"(178mm)


B-ERW-2100

Weatherproof

FEATURES

> Hardwired unit

> AC or DC activation voltage

AGENCY APPROVALS

> UL 2017 Listed

> Registered with the FCC incompliance with Part 68 of FCCRules and Regulations (No.329USA-21250-RG-N)

SPECIFICATIONS

> REN No: 1.5B @ > 50V; 3.4B @ <50V

> AC activation voltage: 10 - 250V

> Ringing frequency: 16 to 70 Hz

> DC Keying Voltage: 10 -150V

> Contact rating: 5 amps at 120V AC

D-04


www.edwards-s ignals.com15-1

8TELEPHONE SIGNALS & ACCESSORIES


7"(178mm)

The Edwards B-ERX-2100 Electronic Telecode Relay is designed to

activate remote extension signals such as horns, bells, strobes, or

similar devices. The relay is activated by the line ringing voltage of

the telephone; operation of the connected signal matches the tele-

phone ringing cycle. The unit is designed for hazardous location

use.

Unit mounts to any flat surface using the supplied hardware. Use

1/2" (13mm) conduit for input and output wiring. All telephone,

power input, and signal output connections are made internal to the

unit.

For hazardous location areas where ambient noise levels are high

or where personnel are unable to be near telephones at all times.

ElectronicTelecode® Relay

FEATURES

> Hardwired unit

> AC or DC activation voltage

> Explosion proof housing

AGENCY APPROVALS

> UL 1203 Listed for Class I,Division 1 and 2, Group D; ClassII, Division 1 and 2, Groups F andG; and Class III locations


SPECIFICATIONS

> REN No: 1.5B @ > 50V;3.4B @ < 50V



> DC Keying Voltage: 10 -150V

> Contact rating: 5 amps at120V AC

B-ERX-2100

Hazardous Location

6 3/4"(172mm)

Mtg. Centers

5 1/8"(130mm)

4 29/32"(125mm)


D-0

4





The Edwards B-KBH-5040-N5 phone bell provides remote indication

of telephone operation. The unit is powered by 120V 60 Hz and

does not draw current on the phone circuit.

The unit is activated by a solid state, voltage sensing relay and re-

sponds to a 16-70 Hz ringing frequency. Operation of the unit

matches the ringing cycle of the telephone. The unit has a 4"

(102mm) steel gong.

Installs with three screws using the three external mounting lugs.

For use in areas that have medium ambient noise levels such as

small warehouses, garages, car lots, gas stations, taxi stands, and

construction sites.

Remote Phone Bell

6 3/8"(162mm)

2"(51)

6 3/8"(162mm)

7 25/32"(179mm)

3/16" (5mm)dia. key

hole slots

5/16" (8mm)dia. hole

4 3/4"(121mm)

B-KBH-5040-N5FEATURES

> Completely self-contained

> Solid state relay

> AC or DC activation

> Polycarbonate injection moldedhousing

> Strain relief connectors fortelephone line and power cord

AGENCY APPROVALS

> UL 2017 Listed


SPECIFICATIONS

> Key voltage: 10-150V DC

> AC activation voltage: 10-250V AC10-70 Hz

> REN No: 1.5B @ > 50V;3.4B @ < 50V

> 6 foot (1.83m) power cord

> 88dB at 10 feet (3.05m)

Wide area phone signaling

D-0

4





The Edwards B-KBP-5060-N5 phone bell provides remote indication

of telephone operation. The unit connects to a 120V 60 Hz supply.

The unit operates on 10-250V AC ringing voltage or 10-150V DC

key voltage. Operation of the unit matches the ringing cycle of the

telephone.

Bell hinges to the die cast back box housing for easy plug-in instal-

lation. Conduit is connected to the unit using the 3/4" (19mm) taps.

For outdoor and indoor areas where ambient noise levels are high

and personnel are unable to be near the telephone at all times.

Ideal for use in factories, foundries, warehouses, printing plants, car

lots, gas stations, taxi stands, loading docks, lumber yards, and

police and fire stations.

Remote Phone Bell

6"(152mm)

7"(178mm)

4 3/4"(121mm)

B-KBP-5060-N5FEATURES

> Weatherproof and dust resistant

> Completely self contained andgasket sealed

> Low current draw

> Solid state relay

> 6" (152mm) chrome plated steelgong

AGENCY APPROVALS

> UL 2017 Listed


SPECIFICATIONS

> REN No: 1.5B @ > 50V; 3.4B @ <50V

> 92dB at 10 feet (3.05m)

Weatherproof

D-0

4





FEATURES

> Xenon strobe lamp

> Solid state circuitry

> Polycarbonate white translucentlens with black lettering

> Piezo horn - warble tone output

SPECIFICATIONS


FEATURES

> REN No: 3.7B

> Strobe: 3 to 7 flashes per cycle

> Horn: 94dB at 5 feet (1.52m)volume adjustable



The Edwards B-KHE-1000-PP remote line powered phone horn/

strobe operates on standard AC ringing voltage (85 - 115V AC) to

provide remote audible and visual indication of a ringing telephone.

The units injected molded housing and cover ensure security.

The unit operates on the ringing voltage and matches the ringing

cycle of the telephone.

The horn/strobe easily installs to the telephone using a modular

telephone jack. Cord and jack are not supplied.

For use in wide area coverage in noisy areas such as machine

shops and equipment operating areas.

Remote Line PoweredPhone Horn/Strobe

5 29/32"(150mm)

2"(51mm)

3 7/16"(87mm)

3 9/64"(80mm)

3 13/16"(97mm)

1 19/64"(33mm)

2 35/64"(65mm)

B-KHE-1000-PP

Hooks up with RJ-11 plug

D-04





The Edwards B-KHD-1000-PP remote line powered phone strobe

operates on standard AC ringing voltage (85 - 115V AC) to provide

remote visual indication of a ringing telephone. The units injected

molded housing and cover ensure security.



The strobe easily installs to the telephone using a modular tele-

phone jack. The cord and jack are not supplied.

For interior use in quiet areas such as libraries, broadcast studios,

hospitals, and offices.

Remote Line PoweredPhone Strobe

5 29/32"(150mm)

2"(51mm)

3 7/16"(87mm)

3 9/64"(80mm)

3 13/16"(97mm)

B-KHD-1000-PPFEATURES

> Xenon strobe lamp


> Polycarbonate white translucentlens with black lettering

AGENCY APPROVALS


SPECIFICATIONS

> REN No: 3.7B

> 3 to 7 Flashes per cycle




D-0

4





The Edwards B-KHP-8010-N5 phone horn provides remote indica-

tion of telephone operation. The unit is powered by 120V 60 Hz and

does not draw current on the phone circuit.

The unit is activated by a solid state, voltage sensing relay and re-

sponds to a 16-70 Hz ringing frequency. Operation of the unit

matches the ringing cycle of the telephone.

Installs with three screws using the three external mounting lugs.

For use in areas that have medium ambient noise levels such as

small warehouses, garages, car lots, gas stations, taxi stands, and

construction sites.

Remote Phone Horn

B-KHP-8010-N5FEATURES

> Completely self-contained

> Solid state relay

> AC or DC activation

> Polycarbonate injection moldedhousing

> Strain relief connectors fortelephone line and power cord

SPECIFICATIONS

> UL 2017 Listed


FEATURES

> Key voltage: 10-150V DC

> AC activation voltage: 10-250VAC 10-70 Hz

> REN No: 1.5B @ > 50V;3.4B @ < 50V

> 6 foot (1.83m) power cord

> 104dB at 10 feet (3.05m)

6 3/8"(162mm)

2"(51)

6 3/8"(162mm)

7 25/32"(179mm)

3/16" (5mm)dia. key

hole slots

5/16" (8mm)dia. hole

4 3/4"(121mm)

Wide area phone signaling

D-04





FEATURES


> Piezo horn - warble tone output

SPECIFICATIONS


FEATURES

> REN No: 3.7B

> Horn: 94dB at 5 feet (1.52m)volume adjustable



The Edwards B-KHS-1000-PP remote line powered phone horn op-

erates on standard AC ringing voltage (85 - 115V AC) to provide re-

mote audible indication of a ringing telephone. The units injected

molded housing and cover ensure security.



The horn easily installs to the telephone using a modular telephone

jack. The cord and jack are not supplied.

For wide area coverage in noisy areas such as machine shops and

equipment operating areas.

Remote Line PoweredPhone Horn

5 29/32"(150mm)

2"(51mm) 3 9/64"

(80mm)

2 35/64"(65mm)

1 19/64"(33mm)

B-KHS-1000-PP


D-04

phone-page telephone signal actuator - leading distributor of

Documents