pic-micro-web development board25 re5/p1c vin is the pin where you should apply 10-50vdc in case you...
TRANSCRIPT
-
PIC-MICRO-WEB development board Users Manual
Rev. C, October 2009
Copyright(c) 2009, OLIMEX Ltd, All rights reserved
Page 1
-
INTRODUCTION:
This small and compact board will give you the opportunity to add Internetconnectivity to any of your existing design or machine. Packed in compactplastic enclosure with DB25 male connector for the microcontroller portsand with the unique PoE (Power over Ethernet) feature which allows PIC-MICRO-WEB to take power by the Ethernet cable and with no need forexternal power supply adapter. The TCP-IP stack provided by Microchip isfree of charge and royalties and allows you to do http, ftp, e-mail etcservices. You can control the PIC GPIOs by web interface and to acquireand send data from external sensors to other Internet applications andclients. With 128K Flash memory for programs and 128KB Flash memoryfor web storage this small device have all resources usually needed forgeneral embedded Internet applications and interface of sensors andmachines to Internet.
BOARD FEATURES:
− PIC18F67J60 microcontroller with Ethernet and 1 Mbit memory for code− 1Mbit on board serial flash for web pages storage− mini ICSP/ICD connector for programming with PIC-ICD2, PIC-ICD2-
TINY and PIC-ICD2-POCKET. − Power-Over-Ethernet support (for use with MOD-PoE power supply
injector on standard LAN cables/switches)− It is possible to use the board without PoE in which case DB25.pin8
(Vin) should be connected to 10-50 VDC source − The board is enclosed in plastic shell DB25 parallel port− 25 available signals and power supply on the DB25 connector − Dimensions 50x30 mm (2 x 1.2")
ELECTROSTATIC WARNING:
The PIC-MICRO-WEB board is shipped in protective anti-static packaging.The board must not be subject to high electrostatic potentials. Generalpractice for working with static sensitive devices should be applied whenworking with this board.
BOARD USE REQUIREMENTS:
Cables: 1.8 meter USB A-B cable to connect PIC-ICD2 or PIC-ICD2-POCKET to USB host on PC or RS232 cable for PIC-ICD2-TINY. Other cables might be required in case of otherprogramming/debugging tools. You will also need a LAN cable.
Hardware: Programmer/Debugger – PIC-ICD2, PIC-ICD2-POCKET, PIC-ICD2-TINYor other compatible programming/debugging tool.MOD-PoE – module that provides Power-Over-Ethernet. If youdon't want to use this module, you should apply power (10-50VDC) directly to DB25.pin8.
Page 2
-
!!!Warning!!! When you want to program this microcontroller with PIC-ICD2, PIC-ICD2-POCKET or PIC-ICD2-TINY, before connectingthe programmer to your target board, you should first connectthe programmer to your computer and open MPLAB. There,first from menu Configure – Select Device – choose themicrocontroller you are about to program, then from menuProgrammer – Select Programmer – choose MPLAB ICD 2, waitwhile MPLAB is downloading operation system, and after ICD2is connected – check in menu Programmer – Settings – Power –there is option – Power target circuit from MPLAB ICD 2 – thisoption should be forbidden, you could not select it. Now it issafe to connect the programmer to your target board.
Software: PIC-MICRO-WEB is tested with MPLAB IDE v.7.62 + MPLABC18 C compiler. It is possible that the stack might notfunction properly if used with later versions of MPLAB IDE.
PROCESSOR FEATURES:
PIC-MICRO-WEB board use MCU PIC18F67J60 from Microchip with thesefeatures:- IEEE 802.3 compatible Ethernet Controller- Integrated MAC and 10Base-T PHY- 8-Kbyte Transmit/Receive Packet Buffer SRAM- Supports One 10Base-T Port- Programmable Automatic Retransmit on Collision- Programmable Padding and CRC Generation- Programmable Automatic Rejection of Erroneous Packets- Activity Outputs for 2 LED Indicators- Buffer:
o Configurable transmit/receive buffer sizeo Hardware-managed circular receive FIFOo Byte-wide random and sequential accesso Internal DMA for fast memory copyingo Hardware assisted checksum calculation for various protocols
- MAC:o Support for Unicast, Multicast and Broadcast packetso Programmable Pattern Match of up to 64 bytes within packet at
user-defined offseto Programmable wake-up on multiple packet formats
- PHY:o Wave shaping output filter
- Selectable System Clock derived from Single 25 MHz External Source:o 2.778 to 41.667 MHz
- Internal 31 kHz Oscillator- Secondary Oscillator using Timer1 @ 32 kHz- Fail-Safe Clock Monitor:
o Allows for safe shutdown if oscillator stops- Two-Speed Oscillator Start-up- High-Current Sink/Source: 25 mA/25 mA on PORTB and PORTC- Five Timer modules (Timer0 to Timer4)- Four External Interrupt pins- Two Capture/Compare/PWM (CCP) modules
Page 3
-
- Three Enhanced Capture/Compare/PWM (ECCP) modules:o One, two or four PWM outputso Selectable polarityo Programmable dead timeo Auto-shutdown and auto-restart
- Up to Two Master Synchronous Serial Port (MSSP) modules supportingSPI (all 4 modes) and I2C™ Master and Slave modes
- Up to Two Enhanced USART modules:o Supports RS-485, RS-232 and LIN 1.2o Auto-wake-up on Start bito Auto-Baud Detect (ABD)
- 10-Bit, Up to 16-Channel Analog-to-Digital Converter module (A/D):o Auto-acquisition capabilityo Conversion available during Sleep
- Dual Analog Comparators with Input Multiplexing- Parallel Slave Port (PSP) module (100-pin devices only)- 5.5V Tolerant Inputs (digital-only pins)- Low-Power, High-Speed CMOS Flash Technology:
o Self-reprogrammable under software control- C compiler Optimized Architecture for Reentrant Code- Power Management Features:
o Run: CPU on, peripherals ono Idle: CPU off, peripherals ono Sleep: CPU off, peripherals off
- Priority Levels for Interrupts- 8 x 8 Single-Cycle Hardware Multiplier- Extended Watchdog Timer (WDT):
o Programmable period from 4 ms to 134s- Single-Supply 3.3V In-Circuit Serial Programming™ (ICSP™) via Two
Pins- In-Circuit Debug (ICD) with 3 Breakpoints via Two Pins- Operating Voltage Range of 2.35V to 3.6V (3.1V to 3.6V using Ethernet
module)- On-Chip 2.5V Regulator
Page 4
-
BLOCK DIAGRAM:
Page 5
-
MEMORY MAP:
Page 6
-
Page 7
-
SCHEMATIC:
Page 8
clos
e
100n
F
100n
F
22pF
22pF
220n
F
CE220uF/10V
100n
F10
0nF
100n
F
100n
F
100n
100n
F
100n
F
4.7n
F
100n
F
100n
F 10u
F/6.
3V
10pF
10pF
2.2u
F/50
V
CE220uF/10V
100n
F
1N58
19(s
md)
WU
06S
ferr
ite b
ead
CL4
7uH
/SD
75
RJP
-003
TC1
red
VIN
VIN
VIN
25M
Hz
3276
8/6p
F
100k
330
49.9
/1%
49.9
/1%
49.9
/1%
49.9
/1%
270/
1%2k
/1%
4.3k
/1%
1.8k
/1%
390K
150K
330
1M
330
10K
PIC
18F6
7J60
AT4
5DB
011
BD
9001
FSO
-8
3.3V
3.3V
3.3V
3.3V3
.3V
3.3V
3.3V
3.3V
3.3V
3.3V
3.3V
3.3V
3.3V
db25
_mal
e
1N47
31(4
.3V
)
#SS1
#SS1
MIS
O
MIS
O
MO
SI
MO
SI
PG
C
PGC
PG
D
PGD
RS
T
RST
RS
TSC
K
SCK
TPIN
+
TPIN
+
TPIN
-
TPIN
-
TPO
UT+
TPO
UT+
TPO
UT-
TPO
UT-
12
3.3V
_E
C1
C2
C3
C4
C5
C6
C7
C8
C9
C10
C11
C12
C13
C14
C15
C16
C17
C18
C19
C20
C24
C31
D1
1 2 3 4 5 6
ICS
P
L1
L2
GN
D7
NC
8
PW
+9
PW
-10
RC
T5
RD
+3
RD
-6
TCT
4TD
+1
TD-
2
LAN
LED
P1
P2
P3
P4
P5
P6
GN
DG
ND
_
Q1
Q4
R1
R2
R3
R4 R
5
R6
R7
R8
R9
R10
R11
R12
R13
R14
R15
R20
#MC
LR7
AV
DD
19
AV
SS
20
EN
VR
EG
18
OS
C1/
CLK
I39
OS
C2/
CLK
O40
RA
0/LE
DA
/AN
024
RA
1/LE
DB
/AN
123
RA
2/A
N2/
VR
EF-
22
RA
3/A
N3/
VR
EF+
21
RA
4/T0
CK
I28
RA
5/A
N4
27
RB
0/IN
T0/F
LT0
3
RB
1/IN
T14
RB
2/IN
T25
RB
3/IN
T36
RB
4/K
BI0
44
RB
5/K
BI1
43
RB
6/K
BI2
/PG
C42
RB
7/K
BI3
/PG
D37
RB
IAS
53R
C0/
T1O
SO
/T13
CK
I30
RC
1/T1
OS
I/EC
CP
2/P
2A29
RC
2/E
CC
P1/
P1A
33
RC
3/S
CK
1/S
CL1
34
RC
4/S
DI1
/SD
A1
35
RC
5/S
DO
136
RC
6/TX
1/C
K1
31
RC
7/R
X1/
DT1
32
RD
0/P
1B60
RD
1/E
CC
P3/
P3A
59
RD
2/C
CP
4/P
3D58
RE
0/P
2D2
RE
1/P
2C1
RE
2/P
2B64
RE
3/P
3C63
RE
4/P
3B62
RE
5/P
1C61
RF1
/AN
6/C
2OU
T17
RF2
/AN
7/C
1OU
T16
RF3
/AN
815
RF4
/AN
914
RF5
/AN
10/C
VR
EF
13
RF6
/AN
1112
RF7
/#S
S1
11
RG
4/C
CP
5/P
1D8
TPIN
+47
TPIN
-46
TPO
UT+
51TP
OU
T-50
VD
D26
VD
D1
38
VD
D2
57
VD
DC
OR
E/V
CA
P10
VD
DP
LL54
VD
DR
X48
VD
DTX
49
VS
S9
VS
S1
25
VS
S2
41
VS
S3
56
VS
SP
LL55
VS
SR
X45
VS
STX
52
U1
/CS
/4
/RE
SE
T/3
/WP
/5
GN
D7
SC
K2
SI
1S
O8
VC
C6
U2
EN
5
FB3
GN
D7
INV
4
N.C
.2
RT
6
SW
1
VIN
8U
4
X1-
1
X1-
2
X1-
3
X1-
4
X1-
5
X1-
6
X1-
7
X1-
8
X1-
9
X1-
10
X1-
11X
1-12
X1-
13
X1-
14
X1-
15
X1-
16
X1-
17
X1-
18
X1-
19
X1-
20X
1-21
X1-
22
X1-
23
X1-
24
X1-
25
Z1
PIC
-MIC
RO
-WEB
Rev
. C
CO
PY
RIG
HT(
C)
2009
, Olim
ex L
td.
http
://w
ww
.olim
ex.c
om/d
ev
+
+
+
2x10
00pF
/2KV
2x75
Ohm
J1 J2 J3 J6
J4,5
J7,8
GN
D
-
POWER SUPPLY CIRCUIT:
PIC-MICRO-WEB takes power over Ethernet using the module MOD-PoE.Other possibility is 10-50VDC to be directly applied to DB25.pin8 if MOD-PoE is not to be used.
The board power consumption depends on the applied power supply andmay vary. At 12VDC the consumption is about 80mA.
RESET CIRCUIT:
PIC-MICRO-WEB reset circuit is made with R20 (10k) pull-up, R13 (330Ω)and capacitor C31 (100nF).
CLOCK CIRCUIT:
Quartz crystal 25 MHz is connected to PIC18F67J60 pin 39 clock in(OSC1/CLKI) and pin 40 clock out (OSC2/CLKO).
Quartz crystal 32.768 kHz is connected to PIC18F67J60 pin 29 (T1OSI)and pin 30 (T1OSO) and supplies the Timer1.
JUMPER DESCRIPTION:
3.3V_Eenables 3.3 V power supply for the PIC18F67J60 and all other
devices.Default state is closed.
INPUT/OUTPUT:
Status red LED connected to PIC18F25J10 pin 44 (PORTB.RB4/KBI0).
EXTERNAL CONNECTORS DESCRIPTION:
ICSP:
Pin # Signal Name
1 RST
2 +5V
3 GND
4 PGD
5 PGC
6 NC
PGD I/O Program Data. Serial data for programming.
Page 9
-
PGC Input Program Clock. Clock used for transferring the serial data (output fromICSP, input for the MCU).
DB25:
Pin # Signal Name Pin # Signal Name
1 RA4/T0CKI 2 RA0/LEDA/AN0
3 RC2/ECCP1/P1A 4 RA2/AN2/VREF-
5 RC7/RX1/DT1 6 VCC +3.3V
7 GND 8 VIN
9 RE1/P2C 10 RD2/CCP4/P3D
11 RE3/P3C 12 RE4/P3B
13 RD0/P1B 14 RA5/AN4
15 RA1/LEDB/AIN1 16 RA3/AN3/VREF+
17 RC6/TX1/CK1 18 RF2/AN7/C1OUT
19 RG4/CCP5/P1D 20 RB1/INT1
21 RB0/INT0/FLT0 22 RE1/P2D
23 RD1/ECCP3/P3A 24 RE2/P2B
25 RE5/P1C
VIN is the pin where you should apply 10-50VDC in case you don't want touse MOD-PoE.
Page 10
-
LAN:
Pin # Signal Name Chip Side Pin # Signal Name Chip Side
1 TPOUT+ 6 TPIN-
2 TPOUT- 7 GND
3 TPIN+ 8 Not Connected (NC)
4 3.3V 9 VIN
5 Not Connected (NC) 10 GND
TPOUT- Output Differential signal output.TPOUT+ Output Differential signal output. TPIN- Input Differential signal input.TPIN+ Input Differential signal input.VIN Input Power supply for the board – over Ethernet.
Page 11
-
AVAILABLE DEMO SOFTWARE :
You could find information about PIC-MICRO-WEB board, Microchip TCP/IPstack and how to change and configure the software on Understanding PICWEB boards on www.olimex.com/dev .
Page 12
-
ORDER CODE:
PIC-MICRO-WEB – assembled and tested (no kit, no soldering required)
How to order? You can order to us directly or by any of our distributors. Check our web www.olimex.com/dev for more info.
All boards produced by Olimex are RoHS compliant
Revision history:
REV.C - created OCtober 2009
Page 13
-
Disclaimer: © 2009 Olimex Ltd. All rights reserved. Olimex®, logo and combinations thereof, areregistered trademarks of Olimex Ltd. Other terms and product names may be trademarks ofothers.The information in this document is provided in connection with Olimex products. Nolicense, express or implied or otherwise, to any intellectual property right is granted by thisdocument or in connection with the sale of Olimex products. Neither the whole nor any part of the information contained in or the product described inthis document may be adapted or reproduced in any material from except with the priorwritten permission of the copyright holder.The product described in this document is subject to continuous development andimprovements. All particulars of the product and its use contained in this document aregiven by OLIMEX in good faith. However all warranties implied or expressed including butnot limited to implied warranties of merchantability or fitness for purpose are excluded.This document is intended only to assist the reader in the use of the product. OLIMEX Ltd.shall not be liable for any loss or damage arising from the use of any information in thisdocument or any error or omission in such information or any incorrect use of the product.
Page 14