piltk4 英文说明书 -v1.0-2019.09 · 2019. 10. 22. · hardware for attaching tv bracket to tv...
TRANSCRIPT
-
Installation InstructionsV1.0
PILTK4
Thank you for choosing our product! We strive to provide the best quality and services for our customers. Would you kindly share your experience on Amazon if you are satisfied? Should you have any issues, please don't hesitate to contact us. Telephone:800-556-9829 Mon-Fri 10am - 6pm (PST) (USA) (CAN)Email:[email protected] (US/CA/DE/UK/FR/IT/ES/JP/AU)
-
Supplied Parts
Tools Needed (Not lncluded)
Stud Finder Tape measure Pencil Drill
5mmWood Drill
10mmConcrete Drill
13mmsocket wrench Screwdriver
Hammer
IMPORTANT SAFETY INFORMATION
•Check package contents against Supplied Parts and Hardware Lists to assure that all components were received undamaged. Do not use damaged or defective parts.lf you require replacement parts, contact customer service at [email protected] •Not all parts and hardware included will be used. •Carefully read all instructions before attempting installation.If you do not understand the instructions or have any concerns or questions, please contact customer service at [email protected]•This product may contain moving parts. Use with caution.•Do not use this product for any purpose or in any configuration not explicitly specified in this instruction. We hereby disclaim any liability for injury or damage arising from incorrect assembly, incorrect mounting, or incorrect use of this product.•DO NOT INSTALL INTO DRYWALL ALONE.
1
Wall Plate
Wall Plate
01 x1
02 x1
Bracket Bracket
8mm Wrench
x1 x1 x103 04 05Level
-
Hardware for Attaching TV Bracket to TV
x4 x8 x8
Philips ScrewsM4 x 12mmM4 x 30mm
x4x4
M-A M-B
Philips ScrewsM6 x 15mmM6 x 30mm
x4x4
M-C M-D
x4
M-E
x4
M-F
Philips ScrewsM8 x 15mmM8 x 45mmM8 x 65mm
x4
M-G
M-I
SpacersL10mm
M-J
SpacersL5mm
M-H
Washersφ6mmM4-5-6
Supplied Hardware
Hardware for Attaching Wall Plate to Wall
Lag BoltsST7X55
x4 x4
A
These anchors are for concrete or brick walls ONLY. DO NOT use them in drywall or wood studs.
CAUTION!
B
Wall Anchor
2
φ10MM
-
Step 2
FLAT BACK TV(UNIVERSAL MONITOR PLATE)
Attach the TV Brackets to the TV
3
M-A/M-C
M-H
M-E
Step 1 Measure VESA and Check TV Screws
Check TV screws
When attaching brackets to the flat screen, be careful not to over tighten screws and be sure that screws do not bottom out in the mounting holes.
Too Short Too Long
Correct Correct
Hand thread screws into the threaded inserts on the back of your TV to determine which screw diameter (M4,M6, or M8) to use.
Measure the distance between the holes located at the back of your TV (these measures may form the shape of a square, or a rectangle) and check that these taken measurements are within the VESA(*) range for this wall mount.VESA: International standard established by the TV manufacturers used to determine if LCD/LED TVs are compatble with wall mounts.
Width
Heig
ht
200 mm ≈ 7 7/8 in400 mm ≈ 15 3/4 in
100 mm ≈ 4 in300 mm ≈ 11 3/4 in600 mm ≈ 23 6/10 in
or
-
ROUND BACK TV (UNIVERSAL MONITOR PLATE)
First, make sure the diameter of the bolt(M-A - M-G) fits your TV. Then, please see the diagram above. You will need to thread the bolt into the TV using the washer (M-H) and spacer (M-I or M-J) if necessary with a screwdriver(Not included). Please make sure the monitor brackets(03/04) are vertically centered and level with each other.
M-B/M-D
M-H
M-IM-J
M-F/M-G
M-IM-J
Step 3 Assemble Mount(Optional)
4
Medium16’’ StudsVESA:100X100-400X400mm
24’’ StudsVESA:100X100-600X400mm
Large
DO NOT overtighten. Tighten only until snug.
or
-
Use a stud finder(not included)to locate wood studs. Mark the edge and center locations.
Step 4
Step 4A
X
For wood stud installation, follow STEP 4AFor concrete installation, follow STEP 4B
Attach Wall Plate [01] or [01/02] to Wall
Wood Stud Option
WARNING:
WARNING:
Ensure the wall plate is securely fastened to the wall before continuing on to the next step.
● Any material covering the wall must not exceed 5/8 in. (16 mm)● Nominal wood stud size: common 2 x 4 in. (51 x 102 mm) minimum 1½ x 3½ in. (38 x 89 mm)● Stud center must be verified
WARNING:
Avoid potential personal injury or property damage! DO NOT over-tighten the lag bolts [A]. Tighten the lag bolts [A] only until they are pulled firmly against the wall plate [01] or [01/02].
5
-
4A-2
4A-3
4A-4
ø5mm
55mm
1/2 in.(13mm)Socket Wrench
Position the wall plate at your desired height and line up the holes with your stud center line. Level the wall plate and mark the holes.
Drill 4 pilot holes using a 5 mm diameter drill bit. Make sure the depth is not less than 55mm.
Install the wall plate [01] or [01/02]. using lag bolts [A] . Tighten the lag bolts [A] only until they are pulled firmly against the wall plate.
6A
-
4B-1 4B-2
ø10mm
60mm
Position the wall plate at your desired height, level the wall plate and mark the pilot hole locations.
Drill 4 pilot holes using a 10mm diameter drill bit. Make sure the depth is not less than 60mm. Never drill into the mortar between blocks.
7
Step 4B
Avoid potential personal injury or property damage! DO NOT over-tighten the lag bolts [A]. Tighten the lag bolts [A] only until they are pulled firmly against the wall plate [01] or [01/02]. .
WARNING:
WallAnchor
B
WARNING:Ensure the wall plate is securely fastened to the wall before continuing on to the next step.
WARNING:● Any material covering the wall must not exceed 5/8 in. (16 mm)● Mount the wall plate [01] or [01/02]. directly onto the concrete surface● Minimum solid concrete thickness: 203 mm (8 in.)● Minimum concrete block size: 203 x 203 x 406 mm (8 x 8 x 16 in.)
Solid Concrete or Concrete Block Option
-
4B-3
Use the hammer to knock anchors [B] into the wall.
8
AB
Install wall plate using lag bolts [A] and anchors [B]. Be sure the anchors [B] are seated flush with the concrete surface. Tighten the lag bolts [A] only until they are pulled firmly against the wall plate. DO NOT over-tighten the lag bolts [A].
Step 5 Ajust the Tilt Tension Screws [S] to Adjust the Tilt Angles of TV
8mm Wrench
03
04Top of TV
Bottom of TV
S
S
SS
Loosen
TightenS
Loosen the six tilt tension screws [S] on both brackets, adjust the hook of the bracket to the desired angle, then tighten tilt tension screws with a wrench (not included) and a screwdriver (not included) to fix the tilting angle of TV.
-
Locking
03
04
Step 6 Hang TV to the Wall Plate [01] or [01/02].
Step 7 Secure TV
9
Pull down and hold both cords [R], press the bottom of the TV into the wall plate [01] or [01/02].until the latches lock the TV in place.
HEAVY! You may need assistance with this step.
Press
R
-
10
Disconnect all cables, pull down and hold both cords [R] while gently pulling the bottom of the TV away from the wall.CAUTION: Avoid potential personal injury or property damage! To prevent breaking the locking latch: always pull and hold the cords [R] down while pulling the TV away from the wall.Then lift the TV up and off of wall plate [01] or [01/02]. Place the TV on cardbard or other protective surface to avoid damage.
NOTE: To rehang the TV, follow the procedures in Step 6 and 7 on PAGE 9.
Removing the TV
HEAVY! You may need assistance with this step.
UnlockingR