pipe & wall video inspection systems user manual · 2014. 10. 22. · trouble shooting trouble...

19
1 PIPE & WALL VIDEO INSPECTION SYSTEMS USER MANUAL For 3688 SERIES ASSEMBLING AND OPERATING INSTRUCTIONS

Upload: others

Post on 30-Nov-2020

1 views

Category:

Documents


0 download

TRANSCRIPT

Page 1: PIPE & WALL VIDEO INSPECTION SYSTEMS USER MANUAL · 2014. 10. 22. · TROUBLE SHOOTING Trouble Reason/Solution Black Screen Abnormal power supply/Check if the power is connected well

1

PIPE & WALLVIDEO INSPECTION SYSTEMS

USER MANUALFor

3688 SERIESASSEMBLING AND OPERATING INSTRUCTIONS

Page 2: PIPE & WALL VIDEO INSPECTION SYSTEMS USER MANUAL · 2014. 10. 22. · TROUBLE SHOOTING Trouble Reason/Solution Black Screen Abnormal power supply/Check if the power is connected well

2

Read instructions carefully before operating this system

WARNING1. Never use this device in an environment with explosive

materials such as GAS, OIL, ETC.2. Avoid using the device in extremely cold, hot or humid environment;

otherwise it may damage the device. Do not drop or press hard onthe device.

3. Avoid using the parts / components from other manufacturers to thissystem, which may damage the equipment due to the un-compatibility.

4. Warranty invalidation if the device is disassembled by users or if there are any physical damages.

5. Always back up your data before connecting your USB stick / MicroSD Card to this system. The manufacturer is not responsible for anydata damage or loss on your USB stick / Micro SD Card for anyreason.

6. Do not disconnect the unit while recording or playing. It may damagethe unit and/or the USB stick / Micro SD Card.

7. Don’t misuse the Battery Charger Cable and Power Cord, otherwisethe battery pack may be damaged or the system cannot workproperly.

8. The system’s PUSH CABLE made of fiberglass is very rigid andnot flexible. It CAN NOT be bent sharply or pushed too hard;otherwise it will be broken.

9. If you have an extra portable cable reel, and try to put it in the caseafter use, you must put it in the right position; otherwise, LCD monitormay be broken by the part on the reel when you close the case.

10. Waterproof camera head should NOT be used under the water ofover 100FT.

11. We reserve the right to make any change about our products withoutany notice in advance.

12. We assume no liability for damage and/or injury resulting from use ofequipment supplied by our company.

Page 3: PIPE & WALL VIDEO INSPECTION SYSTEMS USER MANUAL · 2014. 10. 22. · TROUBLE SHOOTING Trouble Reason/Solution Black Screen Abnormal power supply/Check if the power is connected well

3

CONTENTS Assembly Drawing and Parts List..........................................................4 Specifications..............................................................................5 User Manual..........................................................................................6 Display Device…………………………………………………………….7 Counter....................................................................................................8 Control box………………………………………………………………….9 Pan-Tilt Camera Head.....................................................................11 Cable Reel............................................................................................13 Remote Control ………………………….......................................14 LED brightness......................................................................................15 Video recording and snap shooting............................................... 15 Recharging the Battery.........................................................17

Trouble Shooting ……........................................................................19Daily Maintenance………………………………………..……………........19System Connection Diagram……………………………………………19

Page 4: PIPE & WALL VIDEO INSPECTION SYSTEMS USER MANUAL · 2014. 10. 22. · TROUBLE SHOOTING Trouble Reason/Solution Black Screen Abnormal power supply/Check if the power is connected well

4

Assembly Drawing and Parts ListPart No. Description

1 ROTATE CAMERA

2 _7 INCH _10 INCH MONITOR

3 _60M(200FT) _90M(300FT) _120M(400FT) CABLECFIBERGLASS CABLE

4 BATTERY CHARGER

5 BATTERY CASE

6 FUSE BAG

7 POWER ADAPTER

8 CAMERA SKIDS

9 3M&5M VIDEO CABLE

10 REMOTE CONTROL

11 DISC

12 SKIDS SCREW (12 PCS)

13 Control box

1

1

2

13

Page 5: PIPE & WALL VIDEO INSPECTION SYSTEMS USER MANUAL · 2014. 10. 22. · TROUBLE SHOOTING Trouble Reason/Solution Black Screen Abnormal power supply/Check if the power is connected well

5

Specifications

Item DescriptionPower adapter 110VAC~240VAC 12VDCBattery Case LI-ION batteryLength of Cable _60M(200FT) _90M(300FT)

_120M(400 FT)

Camera Light Source Built-in White LED lights (14PCS)Camera Angle-of-View Camera swing angle: 180°

Camera Inclination Detection:

1. Measuring range: -90°~ +90°

2. Resolution: 1°Camera Rotating Angle 360°Camera Image about 0.44Mpixel_ P A L _ o r

0.38Mpixel_NTSC_Monitor Screen Size 7”OR10” TFT LCD Color MonitorMonitor Picture Resolution 1024_768 pixel (for 10”LCD)

800_480pixel(for 7”LCD)Monitor Input Voltage 12 Volts DCSystem Operating Temperature -28°C to 50°C

Page 6: PIPE & WALL VIDEO INSPECTION SYSTEMS USER MANUAL · 2014. 10. 22. · TROUBLE SHOOTING Trouble Reason/Solution Black Screen Abnormal power supply/Check if the power is connected well

6

User Manual

Application

1. WATER SUPPLY2. WASTE WATER3. ELECTRICAL AIR CONDITIONER4. CABLE DUCTING5. DUCTED VACCUM SYSTEMS6. PLUMBING7. BUILDINGS

WARNING:NEVER USE THIS DEVICE IN AN ENVIRONMENT WITH EXPLOSIVEMATERIALS SUCH AS GAS, OIL, ETC.

Before use1.1 Please connect the camera head with the cable & reel.1.2 Please connect the cable reel with the CAM port on the front

panel with the black soft cable and screw it tightly1.3 Please insert USB/SD in the port1.4 Please insert the DC power in the socket of DC on the front

panel; then the power indicator light will be on and the systemwill start to work automatically after about 7 seconds

Page 7: PIPE & WALL VIDEO INSPECTION SYSTEMS USER MANUAL · 2014. 10. 22. · TROUBLE SHOOTING Trouble Reason/Solution Black Screen Abnormal power supply/Check if the power is connected well

7

Display Device

1. 12V DC2. UP3. DOWN4. DVR POWER5. RETURN6. RECORDING7. LEFT8. SD9. RIGHT10. USB

11. PLAY/ENT12. IR13. REM14. POWER15. CAM16. MIC17. MIC POWER ON/OFF18. MIC LED19. USB PORT20. TF

Page 8: PIPE & WALL VIDEO INSPECTION SYSTEMS USER MANUAL · 2014. 10. 22. · TROUBLE SHOOTING Trouble Reason/Solution Black Screen Abnormal power supply/Check if the power is connected well

8

Counter:Cable with optoelectronic meter counter

1.Reset2.Metric & Imperial conversion3.Display of Metric or Imperial

Page 9: PIPE & WALL VIDEO INSPECTION SYSTEMS USER MANUAL · 2014. 10. 22. · TROUBLE SHOOTING Trouble Reason/Solution Black Screen Abnormal power supply/Check if the power is connected well

9

Control box:

Item feature

Switch Power switch Socket POWER &AVR Socket

K1 UPK2 DOWNK3 TURN RIGHTK4 TURN LEFTK5 HOMEK6 LED UPK7 LED DOWNK8 FOCUS UPK9 FOCUS DOWN

Power Power LED

Page 10: PIPE & WALL VIDEO INSPECTION SYSTEMS USER MANUAL · 2014. 10. 22. · TROUBLE SHOOTING Trouble Reason/Solution Black Screen Abnormal power supply/Check if the power is connected well

10

Connection diagram for controller & Peripheral Unit_

6

_DISPLAY_

_DVR_

_DC POWER_

DVR DISPLAY

To control panel:1_ POWRE2_ DVR DATA.

To Cable:1_ DC POWER;2_ RS485 DATA;3 _ V I D E OSIGNAL.

Page 11: PIPE & WALL VIDEO INSPECTION SYSTEMS USER MANUAL · 2014. 10. 22. · TROUBLE SHOOTING Trouble Reason/Solution Black Screen Abnormal power supply/Check if the power is connected well

11

Pan-Tilt Camera Head

I_Working environment_

1_ Temperature: -28__+50_

2_ Humidity_90%RH (non-condensation)

II_Storage environment_

1_ Temperature: -20__+60_

2_ Humidity: 90%RH(non-condensation)

III. Main Technical Indicators:

1. Power source input: DC 12~18V,8W_maximum_

2. Camera module:

1) Image sensor:1/3 Sony Super HAD _

2) Total pixels: about 0.44Mpixel_PAL_or 0.38Mpixel_NTSC_

3) Horizontal resolution: 600 TVL

4) Minimum illumination: 0.05LUX/F1.2

5) Camera swing angle: 180°

6) LED quantity: 14pcs

7) Light Cup Angle: 45°

Page 12: PIPE & WALL VIDEO INSPECTION SYSTEMS USER MANUAL · 2014. 10. 22. · TROUBLE SHOOTING Trouble Reason/Solution Black Screen Abnormal power supply/Check if the power is connected well

12

3. Camera Inclination Detection:

1) Measuring range: -90°~ +90°

2) Resolution: 1°

Page 13: PIPE & WALL VIDEO INSPECTION SYSTEMS USER MANUAL · 2014. 10. 22. · TROUBLE SHOOTING Trouble Reason/Solution Black Screen Abnormal power supply/Check if the power is connected well

13

Cable reel

1. Meter Counter Box2. Reset Button3. Display4. Meter& imperial Button5. Female Plug6. Cable Wheel

Page 14: PIPE & WALL VIDEO INSPECTION SYSTEMS USER MANUAL · 2014. 10. 22. · TROUBLE SHOOTING Trouble Reason/Solution Black Screen Abnormal power supply/Check if the power is connected well

14

Remote ControlRemote control has the same basic functions with the buttons on thefront panel.

Page 15: PIPE & WALL VIDEO INSPECTION SYSTEMS USER MANUAL · 2014. 10. 22. · TROUBLE SHOOTING Trouble Reason/Solution Black Screen Abnormal power supply/Check if the power is connected well

15

LED brightnessDuring the status of monitoring images or video recording,

press LEFT/RIGHT button and a pop up will be displayed, thenpress LEFT/RIGHT to adjust the LED brightness; pressRETURN to confirm and exit the pop up.

Video recording and snap shooting1.1.RecordingPress RETURN button and main menuPops up (Picture 1), then press RIGHT

Button to select the icon , thenPress PLAY/ENT to start recording theVideos. At This time, RECORDIN and LED lightsWill be on and press PLAY/ENT button again to snap

shooting;Press RETURN button to exit recording and save.You can only take pictures or monitor the pipeline when

selecting the icon in Picture 1.9

2.1_PlayingPress RIGHT button to select , then pressPLAY/ENT, a pop-up (Picture 2) will display on the

screen and you can select the videos or files to play the recorded; Press UP/DOWN button to enter/exit.; PressPLAY/ENT to pause Playing. 2.2_DeletingPress LEFT/RIGHT during the monitoring imagesor videos playing to display the pop-up (Picture 3);Press UP/DOWN to select your choice: selectto give up and exit deleting; select to confirm deleting.3.1.System Setting

Select the setting icon in the main menuto change the setting and then the main menufor Setting will display (Picture 4).3.2.Playing setting

Select player icon to change the setting

Picture1

Picture 2

Picture3

Picture 4

Page 16: PIPE & WALL VIDEO INSPECTION SYSTEMS USER MANUAL · 2014. 10. 22. · TROUBLE SHOOTING Trouble Reason/Solution Black Screen Abnormal power supply/Check if the power is connected well

16

3.3. Storage and Formatting Select storing option icon to know the current storage and

formatting. Left is the TF card volume; Right is the USB volume.

103.4. Time and Date Setting

Select Clock setting icon t to set the time_Press UP/DOWNto select the target and LEFT/RIGHT to adjust the numbers.

3.5. Version InformationSelect version icon to know the current software.

No Single RotatingSingle RotatingMultiple Rotating

Total Storage

Files VolumeFormatting

PLAY Button for Time Zone Change

Date Setting

Time Setting

Page 17: PIPE & WALL VIDEO INSPECTION SYSTEMS USER MANUAL · 2014. 10. 22. · TROUBLE SHOOTING Trouble Reason/Solution Black Screen Abnormal power supply/Check if the power is connected well

17

Recharging the Battery1) Plug the charger into the AC socket on the wall and insert the

other end into the DC jack of battery box (See Figure2- A). Note : Don’t misuse the battery charger cable and power code, otherwise the battery pack may be damaged, or the system

cannot work properly.2) Press the charge button (See Figure2-B) while the Battery Box is

turned off. The battery can be charged while the battery box is on andthe device is being used. However, once the power in the batteryruns completely out, it can only be charged when the Battery Boxis turned off.

3) The charge LED will be red during charging and will turn greenwhen charging is over (Normal charging time: 5 - 6 hours).

Figure 2

IMPORTANT MESSAGE: Do not overcharge the battery! Overchargingcan result in acid leaking from or damage to the battery.

Page 18: PIPE & WALL VIDEO INSPECTION SYSTEMS USER MANUAL · 2014. 10. 22. · TROUBLE SHOOTING Trouble Reason/Solution Black Screen Abnormal power supply/Check if the power is connected well

18

Battery specifications:1. TOTAL POWER 12W2. LI-ION BATTERY 12VDC MAX._ 40Wh3. CHARGER 13.5V 800mA4. CHARGE TIME 6 HOURS5. WORKING TIME ≥120 MINUTES6. PROTECTIVE VOLTAGE 8.1V7. THE VOLTAGE BEFOR DISCHARGING 12.6V8. LOAD CURRENT 1100mA(INPUT 12.2V HOUR)

Page 19: PIPE & WALL VIDEO INSPECTION SYSTEMS USER MANUAL · 2014. 10. 22. · TROUBLE SHOOTING Trouble Reason/Solution Black Screen Abnormal power supply/Check if the power is connected well

19

TROUBLE SHOOTINGTrouble Reason/Solution

Black Screen Abnormal power supply/Check if the power is connectedwell to ensure the sufficient power.

No signal No signal transfer/Check if the connection is good andreconnect all parts referring to the connection diagram.

No recording Not inserting the USB/SD or the USB/SD has no sparespace/Insert the USB/SD with enough space.

Lights off Camera head is not on the right position/Screw off thecamera head and on the cable connector again.

Not enoughpower

Battery not fully recharged/ Fully charge the battery andthen use.

Battery notcharging

Poor contact of the power adapter or damaged battery/Ensure the good contact with the charger or change thebattery.

Daily maintenance1.1. Keep the product clean. Clean the camera head and cable &

reel before disconnecting to avoid the water splashed on thePCB board on the camera head or gold pins. Once there aresplashed water drops, please clean the parts with the drycloth immediately. Disconnect the parts after the product isdry. Put the cover on the camera head connector and CAMconnector on the front panel. Put it away in the same way aswhen the package is received.

1.2. Put it away in the dry environment and keep it out of reach ofchildren.

System Connection Diagram Control Box (Option)

------ -----SoftCable

Cable &Reel

CameraHead

DisplayScreen

180º/360º PanTilt Camera2.4G WirelessText Writer