pipemarker v8 manual - epson labelworks pxlabelworks.epson.com/wp-content/uploads/2017/07/... ·...

System RequirementsMicrosoft Windows® 8.1, 8, 7, Vista, XP

100 Mb HDD SpaceXGA (1024 x 768) or higher

K-Sun® PEARLabel® 400iXL printer and/or K-Sun® PEARLabel® 360 printer

PipeMarker™ V8 MAnuAL

K-Sun® PipeMarker™ V8K-Sun® PipeMarker™ V8 software allows you to print pipe markers, pipe tags, and arrow, checkerboard and diagonal stripe tape to aid in compliance with OSHA, nFPA, IIAR, CGA, nEC, and AnSI pipe and electrical conduit identification requirements. PipeMarker™ V8 includes over 815 predefined markers covering requirements for general facility use, physical plant, pulp and paper plants, chemical plants, food processing and manufacturing and medical facilities. In addition, it allows you to create and save your own custom markers by adding signal words, pictographs, supplemen-tal information, pipe ID, QR or Data Matrix bar codes or marker serialization.

What’s New in K-Sun® PipeMarker™ V8?Added: Pipe Size 10+ inchesAdded: Pre-designed Pipe Markers – 3 new categories (Food Processing, Facility Markers, & HVAC Duct Marking)Added: 200+ Pre-designed Pipe Markers Now works with K-Sun® PEARLabel® 400iXL 1”, 2”, 4” printer and K-Sun PEARLabel® 360 (1” and 1.5” tape sizes)Added: Pattern Printing for Arrow, Checkerboard or Diagonal Stripe TapeAdded: Import up to 100 pictographs/symbolsAdded: QR Code or Data Matrix barcodesAdded: Serialization after legendAdded: Spanish Signal Words Now works with Windows® 8.1, 8, 7, Vista, XPAdded: Ability to print durable IIAR markers using separate component printing.Added: Ability to print Medical Gas Markers using Pattern Printing.

3

Table of Contents

1. Quick Start Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Insert

2. Installing/Uninstalling PMV8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-9

3. Using Pre-designed Markers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-19

4. Editing a Pre-designed Marker to Custom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20-40 4.1 Edit Pipe Marker Text Dialog Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21-31

4.2 Edit Pipe Marker Graphics Dialog Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32-39

4.3 Adding Company Information to Marker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

5. Creating NEW Pipe Marker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41

6. Saving Custom Pipe Markers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42

7. IIAR Markers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43-48

8. Medical Gas Markers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49-57

9. Pattern Printing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58-60

10. Regulation Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61-62

11. Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back Page

PipeMarker™ V8 Quick Start Guide

START THE PROGRAMStart the program from the desktop by double clicking on the K-Sun® PipeMarker™ V8 program icon.

The program’s main screen opens.

Select PrinterClick in the [Printer] box. Choose PEARLabel® 400iXL for all marker sizes. Choose PEARLabel® 360 for smaller markers.

Select Tape Width PEARLabel®400iXL

PEARLabel® 360

2

Open a Pipe Marker by �rst selecting a category and then Pipe Legend. Click in the [Category] box and a list of pipe marker categories will drop down. To choose a category, highlight and [Click].

Next, click on the [Pipe] legend box.

A list of pre-designed markers will appear. Scroll through the choices. To choose a marker, highlight and click. The marker appears on the screen.

1

Select Language, Pipe Size, Flow (arrow direction) and Format.Click in the [Language] box and select the desired language format. Choose from English, Spanish, or Bilingual format.

Click in the [Flow] box and select the desired �ow direction. Choose from left, right, or both.

Click the desired [Format] button to select the placement of the arrow - none, left, right or both.

3

The displayed pipe marker will change to re�ect your selections.

Edit the Pipe MarkerDouble-Click on the displayed pipe marker to access the Edit the Pipe Marker Text dialog box and the Edit the Pipe Marker Graphics dialog box. Toggle between screens using the button in the lower corner of the box Edit Text, Edit Graphics. Make desired changes to any marker and click [OK] to return to the main screen.

4

Click in the [Pipe] Size box and select the corresponding outside diameter size of the pipe to be marked.

5

USAGE GUIDELINE A pipe marker usage guideline box will be displayed that lists regulatory and standards information pertinent to the pipe marker being printed. Read the guidelines carefully.

Print the Pipe MarkerThe marker on the screen shows how the marker will print. Con�rm color of supplies in printer.Choose Print Button or Click on PipeMarker, Print.

The Print Box will indicate the total number of markers that will print in the set based on the marker design, pipe size and tape width. Do not change this number.

Example: Pipe size ¾ - 1 ¼ printing on 4” tape may yield 4 markers while Pipe size ¾ - 1 ¼ printing on 1 ½” tape may yield 1 marker in set.

Click [OK].

The Printer dialog box will appear for the K-Sun® PEARLabel® 400iXL or PEARLabel® 360 printer.

To preview the pipe marker before printing, set Print Preview in Properties.

If more than one set of markers is needed, change the number of markers to print at Copies, Number of Copies.

SET PRINT PREVIEWTo set print preview choose [Properties] on the print screen. Then on the [Options] Tab, check Print Preview. Click [OK].

Now at the Print dialog screen click [OK].A printer dialog box will appear with Tape Width Value (Choice made in program) and Current Tape Width (Supply in printer)If these match, click [OK].

If Print Preview was selected: Review the marker before printing. If OK click on the printer icon. To cancel printing click on Red X icon and a dialog box will appear explaining “Printing will be canceled. Ok?” Yes or No. Select Yes.

K-Sun® Corporation 370 SMC Drive | Somerset WI 54025 1.800.622.6312 | [email protected] | www.ksun.com1/2014 SL00513-B

Installing/Uninstalling PMV8

Installing/Uninstalling PM

V8

1

2. Installing K-Sun® PipeMarker™ V8This is an autorun CD. The installation CD browser should start automatically once the CD is placed in the drive. If it does not start automatically, run the setup program on the CD. Once the CD browser has started, click the Install Software button and follow the instructions on the screen.

DO NOT CONNECT THE PRINTER TO THE USB UNTIL INSTRUCTED.

Note: Software Program K-Sun® PipeMarker™ V8 will be installed into the default directory (default: K-Sun\PMV8)

The K-Sun® PipeMarker™ V8 Installer screen appears. Choose [Install Application and Driver].

If MaxiLabel Pro Ver 5.0 is already installed, this screen will appear first when installing. Choose [Modify].


V8

2Installing/Uninstalling PMV8


V8

When the license agreement dialogue box appears, read and confirm the contents and click [Agree]. To abort installation: Click [Disagree].

The install begins.



V8

When the destination selection dialogue box appears, confirm the destination folder, and click [Next]. Installation begins. To change the destination folder: Click [Browse...].

The Setup begins.



V8

When the completion message appears, the installation is complete. Click [Finish]. To create a desktop shortcut, leave on the marked check box.

There may be a slight pause while the printer driver install begins. DO NOT PLUG IN THE USB until instructed.



V8

Installing Printer Driver. If you have already installed MaxiLabel® Pro Ver 5.0 and the PEARLabel® 400iXL or PEARLabel® 360 printers choose [Cancel] here.

Otherwise use the drop down menu and choose the PEARLabel® 400iXL printer.

Select printer. Click [Next].



V8

Follow the instructions on the screen. Connect the adapter, plug in the uSB, and turn power on printer.

Wait for the completion message (Green Check Mark). The driver install is now complete. Choose [Finish].

To install the K-Sun® PEARLabel® 360 Insert the software CD-ROM into CD-ROM drive on your computer. orReturn to C:\K-Sun\PMV8 directory and double click on [Setup.exe]



V8

The Modify screen appears. Click [ Modify].

The K-Sun® PipeMarker™ V8 Installer screen appears. Choose [Install driver only].

Read and accept the license agreement.



V8

Select K-Sun® PEARLabel® 360 printer. Click [Next].

Follow the instructions on the screen. Plug in the adapter and plug in the uSB.



V8

Wait for the Green Check Mark. Click [Finish].

NotE foR NEtWoRK AdmiNiStRAtoRS:Printers can be connected to a PC using Windows® 8,7,Vista, XP that is part of a network and print from one common printer. However the following functions cannot be accepted from the client:1. Acquiring the tape width when using MaxiLabel® Pro Ver 5.0 or PipeMarker™ V8.2. Operating the printer property utility.

The Readme fileThe Readme file contains last minute notes, troubleshooting tips, and other useful information that may not beavailable in any other area of the software or the documentation. When it is displayed, print it by clicking on File and then Print. From the desktop, click [Start], then go to Installed Location (Default is C:\K-Sun). Open the folder PMV8 and locate “PMV8 readme.txt”

Uninstalling K-Sun® PipeMarker™ V8Note: uninstalling K-Sun® PipeMarker™ V8 will permanently delete your custom marker categories.

Copy the files, “PIPE.FIL”, “P-cust1.cat”, “P-cust2.cat”, “P-cust3.cat”, “P-cust4.cat”, and “P-cust5.cat” from the directory (default: “..\K-Sun\PMV8) to a known location for reinstallation.

To remove K-Sun® PipeMarker™ V8 from your computer or install it on a different computer:

First: Uninstall K-Sun® PipeMarker™ V8use the Add/Remove Programs utility in the Control Panel to uninstall K-Sun® PipeMarker™ V8

Second: Uninstall Drivers for K-Sun® PEARLabel® 400iXL and 360.use the Add/Remove Programs utility in the Control Panel to uninstall MaxiLabel® Pro Printer Driver.

Windows® 8.1 Upgrade from 8.0 - Install driversunplug printer(s) uSB.Insert CD and select [Modify]. Choose [Install driver only].Select printer. Follow instructions on screen. When instructed plug in uSB and turn on if needed. Wait for the Green Check Mark. Click [Finish].

10using Pre-designed Markers

Using Pre-designed M

arkers

3. Using Pre-designed Pipe MarkersCategoryK-Sun® PipeMarker™ V8 organizes pipe markers into 19 categories to easily find and keep track of markers. Pre-designed pipe markers are named after general types of pipe and conduit applications. Fourteen of the 19 categories contain predefined pipe markers that are supplied with the software. Custom1 through Custom5 contain pipe markers that are created and saved. Each custom category holds 200 custom pipe markers.

Click in the box labeled Category to see the list of Categories. Select a Category by clicking on it.

List of CategoriesIIARAirChemicalElectricalFireFacilitiesFoodManufacturingMedical GassesPulp PaperVacuumWaterFacility MarkersHVAC MarkersCustom1Custom2Custom3Custom4Custom5

using Pre-designed Markers11

Legend Selection within CategoryTo see a list of pipe markers within a Category, click in the box labeled Pipe.

Each pipe marker in the list is identified by its Field Color, Pictograph, Signal Word and Legend. Click on the pipe marker you want to view and it will be displayed on the screen.

imPoRtANt NotE: The AnSI/ASME A13.1-2007 standard has identified specific colors for flammable liquids, combustible fluids and toxic or corrosive fluids. You must consult MSDS/SDS Sheets before selecting a color. If the pipe content contains multiple hazards, for instance flammable and toxic, it must be determined which poses the greater risk and mark appropriately.


arkers



arkers

Search for Pipe MarkersManual SearchTo find pipe markers by manually paging through them, click on the desired category in the Category box. Then click in the Pipe box and use the up/down arrows on your keyboard to page through the pipe markers in that category.

Automatic Search

To find pipe markers using the automatic Search function, click on the Search button to the right of the Category Box.A Search for markers dialog box will pop up. Search for pipe markers by specifying up to three words, in any order, from the English and Spanish Legend and Supplemental text. Click [OK]. The software will search all categories (except the IIAR category), find all the pipe markers that contain the words entered and copy them into the “Search on... Category.” Click [OK]. The pipe markers will be saved in the “Search on... Category” until there is a new search.


LanguageAll pre-designed pipe markers have both English and Spanish legends and each pipe marker can be printed in one of three language options: English, Spanish, and Bilingual formats. Click in the Language box and click on the desired language option.

When Spanish is selected, the pipe marker will look the same as the English pipe marker except that the equivalent Spanish legend is displayed. When Bilingual is selected, both English and Spanish legends are displayed. When you make your selection, the displayed markers will change to reflect your choice.Note: Translations from English to Spanish should be reviewed for clarity and accuracy by the user. Several expressions and dialects exist and K-Sun® has presented the most popular translation to the best of our ability.

Note: If editing a bilingual pipe marker, edit both the English and Spanish legend (text). If you do not want to edit the Spanish portion, delete it before saving the marker. The Spanish portion is only displayed and printed if Bilingual or Spanish Language options are selected.

To type special Spanish characters hold down the Alt key and type the character.

To type superscripts and subscripts into a pipe marker legend:

Superscript use a carat symbol “^” preceding text character Subscript use a tilde symbol “~” preceding text character

Only the character following the symbol will be superscripted or subscripted. If more than one character needs to be superscripted or subscripted then the desired symbol must precede each character.


arkers



arkers

Pipe (Pipe Size)

Click in the [Pipe] box and select the size that corresponds to the outer diameter of the pipe to be marked. The software will automatically adjust the length of the marker and the height of the legend letters to comply with AnSI/ASME A13.1-2007 or nFPA 99c.

After selection, the displayed marker will change.

Depending on the Pipe Size and the material size to be printed on, the screen will show how many markers can be printed.

For instance: ¾- 1 ¼ pipe size

using K-Sun® PEARLabel® 360 printer with 36mm supply: 1 marker

using K-Sun® PEARLabel 400iXL printer with 4” supply: 4 markers

The ASME/AnSI and nFPA standards do not specify marker size for pipes less than 3/4” diameter and recommend using tags for pipes less than 3/4’” diameter. K-Sun® PipeMarker™ V8 includes a small marker size for use on pipes less than 3/4” where appropriate.



arkers

Tape WidthFor the K-Sun® PEARLabel® 400iXL there are 24mm/1”, 50mm/2” or 100mm/4” tape widths available.For the K-Sun® PEARLabel® 360 there are 24mm/1’ and 36 mm/1 ½” tape widths available.The choice of printer, pipe size and width will determine how many markers are printed. Example: K-Sun® PEARLabel® 400iXL, Pipe size ¾ - 1 ¼ and 100mm will make 4 markers:

Example: K-Sun® PEARLabel® 360, Pipe size ¾ - 1 ¼ and 36mm will make 1 marker.

Note: K-Sun® PipeMarker™ V8 automatically sizes text as required by AnSI/ASME Scheme for the Identification of Piping Systems ASME A13.1-2007.



arkers

Format - Flow (Arrow Direction) ANSi A13.1-2007 Standard “Arrows shall be used to indicate direction of flow. Where flow can be in both directions, arrows in both directions shall be displayed.”

using the format buttons create markers with no arrows, arrows on only the right or left end, or arrows on each end.

Click in the [Flow] box and select under [Format] the desired flow direction for the marker. The choices are Left, Right and Both.

After [Flow] choice, click on [Format] choice. The displayed marker (and the arrows on the Format buttons) will change.

Example: Left Arrow Flow one position

Example: Right Arrow Flow two positions

Example: Both Arrows Flow two positions



arkers

To change the Style of Arrows to Chevron or Double Chevron, Double Click on the label and use the Edit the Pipe marker Graphics screen.

Select Arrow Style and click [OK].

Format – Tags or Arrow Tape using the format buttons create arrow tape or tags.

18Using Pre-designed Markers


arkers

TagsASME/AnSI standards do not specify marker size for pipes less than 3/4” diameter and recommend using tags for small pipes. Tags may also be used to mark valves and components. Any pipe marker can be printed out in tag format.

Click on the [Format] with the tag icon. The displayed marker will change to tag format.

Note: Tag Format requires 100mm supply.

Note: Only one symbol per tape can be added.Tags printed bilingual will have note about other language on reverse side.

Arrow TapeArrow only tape can be created in K-Sun®PipeMarker™ V8 by using either the arrow tape icon or Pattern Printing Method (see pgs 58-60).

Click on the arrow tape icon

A blank marker appears.

Double-Click inside the marker.

19Using Pre-designed Markers


arkers

Edit the Pipe Tape Graphics dialog box appears. Select available Pictograph (Symbols) by highlighting and the clicking the >> Button. Symbol will show selected.

A row of arrows (or other pictographs –up to 3) will appear.Choose [Pipemarker] [Print].

Note: If pictographs or arrow only appear once or twice or to repeat more often, increase pipe size and or print multiple copies. Also, consider using pattern printing to create arrow tape.

20Editing Pre-designed Marker to Custom

Editing Pre-designed Marker to Custom

4. Editing a Pre-designed Marker to CustomWhen you edit a marker, K-Sun® PipeMarker™ V8 automatically makes changes to the marker layout to accommodate those changes.

Editing a pre-designed or previously saved pipe marker will not change the saved version of the pipe marker. Save the changed version as a new pipe marker in the Custom Category. (see Saving Pipe Markers)

It is not possible to delete or overwrite pre-designed pipe markers that come supplied with the software.

Select a pre-designed marker.

Select PipeMarkers, Edit, then click on Text or Graphics to edit the currently displayed marker. The desired Edit dialog box will pop up.

Make changes in the Edit the Pipe Marker Text dialog box or the Edit the Pipe Marker Graphics dialog box.


4.1 Edit Pipe Marker Text Dialog Box

Color – Field Color

Select the appropriate field color for your application. Field colors are the main background color of a marker. The following field colors are available:

Field Color Text Color IndicatesRed Field White Fire, DAnGER, Medical Gas Piping - Instrument AirYellow Field Black Flammable Liquid, CAuTIOn, Medical Gas-Medical AirOrange Field Black Toxic & Corrosive Fluids, WARnInG, Energized EquipmentBrown Field White Combustible Fluids, Medical Gas Piping- HeliumGreen Field White Potable, Cooling Water, Safety Equip,

Medical Gas-OxygenBlue Field White Compressed Air, nOTICE,

Medical Gas Piping-nitrous OxidePurple Field White user Defined, Medical Gas-Waste Anesthetic Gas DisposalWhite Field Black user Defined, Medical Gas-Medical Surgical VacuumWhite Stripe Black Medical Gas-non-medical and Category 3 VacuumWhite Checker Black Medical Gas Piping - Laboratory VacuumGray Field White user Defined, Medical Gas Piping-Carbon DioxideBlack Field White user Defined, Medical Gas Piping-nitrogenYellow Field Black Medical Gas-non-medical Air Cat. 3 Gas Powered DeviceYellow Checker Black Medical Gas Piping-Laboratory Air

Note: Stripe and Checker fields do not appear on the screen but can be created using Pattern Printing.

IMPORTANT NOTE: The ANSI/ASME A13.1-2007 standard has identified specific colors for flammable liquids, combustible fluids and toxic or corrosive fluids. You must consult MSDS/SDS Sheets before selecting a color. If the pipe content contains multiple hazards, for instance flammable and toxic, it must be determined which poses the greater risk and mark appropriately.


22Editing Pre-designed Markers to Custom

Legend AlignmentClick the corresponding radio button for the desired alignment. Align text with the left side of the marker, centered on the marker, or on the right side of the marker. Select Vertical Legend or Rotate 180 degrees.

Vertical LegendsLegend Alignment changes from Left, Center, Right to Top, Center, Bottom.

The displayed marker will change to reflect your selection.

Note: Pictographs added to vertical legends will be displayed in the same orientation as vertical text. Imported pictographs will not rotate.



English Legend/Spanish LegendThe pipe marker legend identifies the pipe’s contents. K-Sun® PipeMarker™ V8 allows you to enter or add to the legend in both English and Spanish for all non-IIAR markers. Text is automatically sized as required for the pipe diameter, and set to be black or white letters, per AnSI/ASME guidelines.

All pre-designed pipe markers include Spanish Legends that are translations of the English Legend.

Note: When you edit a pipe marker, you must edit both the English and Spanish legend if you wish to have the Spanish Legend correspond to the English Legend. If you do not want to edit the Spanish portion you can delete it before saving your marker. In any case, the Spanish portion is only displayed and printed if you select Bilingual or Spanish Language options. See also special characters.

One line of Supplement information can be added in each language. This line can be used alone or in conjunction with Signal Words and Pictographs to give a specific warning about the pipe’s contents or to add any additional information that may enhance safety or facilitate identification and maintenance. The font size will automatically be set to be smaller than the Legend font size.

When adding Signal Words or additional lines of text, set PRInT PREVIEW on to review before printing. For some Pipe Size/Tape width combinations it is not possible to add Signal Words and Text. Either chose a larger width supply or do not add the Signal Words/and or text.



Printing markers created with Signal Word and/or Additional LineFor some markers/sizes adding the signal word or additional line requires choosing larger tape width (to accom-modate the extra text) or not using signal word or additional line on the marker.

If you create a marker that requires a larger tape width, an information panel appears:Adding Signal Word or Additional Text on this Marker requires Larger Tape Width.

Here is a chart to help you. for markers highlighted in Yellow that say Yes, either remove signal word and text or go to next larger width when possible.

Printer Pipe [Size] Tape WidthAdd Signal

Word Add Line 3 Tape Message400iXL <3/4 24mm Yes Yes Yes400iXL 3/4 -1 1/4 24mm Yes Yes Yes400iXL 1 1/2 - 2 24mm Information: Pipe Marking Standard for Letter Size requires Larger Tape Width

400iXL <3/4 50mm Yes Yes no400iXL 3/4 - 1 1/4 50mm Yes Yes no400iXL 1 1/2 - 2 50mm Yes Yes no400iXL 2 1/2 - 6 50mm Yes Yes Yes400iXL 8-10 50mm Information: Pipe Marking Standard for Letter Size requires Larger Tape Width

400iXL <3/4 100mm Yes Yes no400iXL 3/4 - 1 1/4 100mm Yes Yes no400iXL 1 1/2 - 2 100mm Yes Yes no400iXL 2 1/2 - 6 100mm Yes Yes no400iXL 8-10 100mm Yes Yes Yes400iXL >10 100mm Yes Yes Yes

360 <3/4 24mm Yes Yes Yes360 3/4 - 1 1/4 24mm Yes Yes Yes360 1 1/2 - 2 24mm Information: Pipe Marking Standard for Letter Size requires Larger Tape Width

360 <3/4 36mm Yes Yes no360 3/4 - 1 1/4 36mm Yes Yes Yes360 1 1/2 - 2 36mm Yes Yes Yes360 2 1/2 - 6 36mm Information: Pipe Marking Standard for Letter Size requires Larger Tape Width



Signal WordsPipe marker standards make no mention of the inclusion of signal words on pipe markers.Signal Words are standardized words and surrounds that are intended to capture the employee’s immediate attention. A Signal Word can be used alone or in conjunction with a Pictograph (symbol) or Supplement to give a specific warning about the pipe’s contents or to add any additional information that may enhance safety or facilitate identification and maintenance. K-Sun® PipeMarker™ V8 includes English and Spanish signal words, and one or the other, or both, will appear on marker depending on the Language option.

Choose from among the 8 Signal Words, in Spanish or English in AnSI Z535.4-2011 Style. The Signal Words are available in reverse for working with White Ribbon. The Signal Word will be displayed at the bottom left corner of the marker. In the case of vertical legend markers, the signal word will be displayed at the top left corner of the marker.

NotE: Signal Words only print out in the color of the marker/ribbon. Consider carefully before adding signal words to a marker.



To Add a Signal WordDouble-Click the displayed marker and go to the Edit the Pipe Marker Text dialog box.

Click the drop-down list box to see all available signal words and click on the desired signal word.

Signal Word will be added to marker.



Usage Guidelines – Signal Words

BIOHAZARD[29 CFR 1910.145(f )](8) Biological hazard tags. (1) Biological hazard tags shall be used to identify the actual or potential presence of a biological hazard and to identify equipment, containers, rooms, experimental animals, or combinations thereof, that contain or are contaminated with hazardous biological agents.

[29 CFR 1910.145(e)](4) Biological hazard signs. The biological hazard warning shall be used to signify the actual or potential presence of a biohazard and to identify equipment, containers, rooms, materials, experimental animals, or combinations thereof, which contain, or are contaminated with, viable hazardous agents. For the purpose of this subparagraph the term “biological hazard,” or “biohazard,” shall include only those infectious agents presenting a risk or potential risk to the well-being of man.

[AnSI Z535.2-2011]no mention of this signal word for signs.

[AnSI Z535.5-2011]no mention of this signal word for tags.

CAUTION[29 CFR 1910.145 (f )](6) Caution tags. Caution tags shall be used in minor hazard situations where a non-immediate or potential hazard or unsafe practice presents a lesser threat of employee injury. Caution tags shall be used only in these situations.

(2) Caution signs. (i) Caution signs shall be used only to warn against potential hazards or to caution against unsafe practices. (ii) All employees shall be instructed that caution signs indicate a possible hazard against which proper precaution should be taken.

[AnSI Z535.5-2011]4.3 Caution tags: Indicates hazardous situations that, if not avoided, could result in minor or moderate injury.

[AnSI Z535.2-2011]4.11.3 Caution signs:Indicates hazardous situations that, if not avoided, could result in minor or moderate injury.



DANGER[29 CFR 1910.145 (f )](5) Danger tags. Danger tags shall be used in major hazard situations where an immediate hazard presents a threat of death or serious injury to employees. Danger tags shall be used only in these situations.

(1) Danger signs. (i) There shall be no variation in the type of design of signs posted to warn of specific dangers and radiation hazards. (ii) All employees shall be instructed that danger signs indicate immediate danger and that special precautions are necessary.

[AnSI Z535.5-2011]4.1 DAnGER tags: 1) are used to indicate hazardous situations which, if not avoided, will result in death or serious injury. This signal word is be limited to the most extreme situations.2) DAnGER tags may be used for lock-out/tag-out situations when used with the intention of preventing death or serious injury.

[AnSI Z535.2-2011]4.11.1 DAnGER signs:Indicates a hazardous situation that, if not avoided, will result in death or serious injury. This signal word is to be limited to the most extreme situations.

EMERGENCY[29 CFR 1910.145]no mention of this signal word for signs or tags.



NOTICE[29 CFR 1910.145]no mention of this signal word for signs or tags.

[AnSI Z535.5-2011]4.4 nOTICE tags: Indicates information considered important, but not hazard-related (e.g. messages related to property damage.) The safety alert symbol may not be used with this signal word.

[AnSI Z535.2-2011]4.11.4 nOTICE signs: Indicates information considered important, but not hazard-related (e.g. messages related to property damage.) The safety alert symbol may not be used with this signal word.



SAFETY FIRST[29 CFR 1910.145]no mention of this signal word for signs or tags.



THINK[29 CFR 1910.145]no mention of this signal word for signs or tags.



WARNING29 CFR 1910.145(f )](7) Warning tags. Warning tags may be used to represent a hazard level between “Caution” and “Danger,” instead of the required “Caution” tag, provided that they have a signal word of “Warning,” an appropriate message and otherwise meet the general tag criteria of paragraph (f )(4) of this section.

no mention of this signal word for signs.

[AnSI Z535.2-2011]

4.11.2 WARnInG Signs:Indicates a hazardous situation that, if not avoided, could result in death or serious injury.

[AnSI Z535.5-2011]4.2 WARnInG Tags:Indicates a hazardous situation that, if not avoided, could result in death or serious injury.



Serialization-After LegendPipe marker standards make no mention of the inclusion of identification or serialization on pipe markers.

Add identification to individual pipe markers in the form of a prefix and or a number. Most commonly this is used for location identifiers or system component identifiers to assist in maintenance or trouble reporting.

The prefix can be up to 8 letters or numbers. The starting number chosen will appear on the first pipe marker and will be incremented for the number of markers printed. Specifying a starting serial number of 0 disables display of the serial number on the pipe marker. Valid values are 0 to 30000. For non-incremental numbers place the desired number in the prefix box.

Double-Click the marker. On the Edit the Pipe Marker Text Dialog box, under Serialization, check the After Legend box. Add Prefix if needed and Starting number. Click [OK].

Marker will reflect Serialization.

On the usage guidelines page indicate the number of markers needed.

Based on the above selection of 5, markers will print FIRE RISER W1, FIRE RISER W2, FIRE RISER W3, FIRE RISER W4, FIRE RISER W5.



Serialization-On Marker To create serialization on marker, but not after legend, enter Prefix and Starting number. Do not check After Legend box.

Serialization will appear in bottom right corner of marker.



4.2 Edit Pipe Marker Graphics Dialog Box

Pictographs/SymbolsPipe marker standards make no mention of the inclusion of pictographs/symbols on pipe markers.

A symbol is a pictorial representation used to identify a hazardous condition or to convey a safety instruction. Symbols can be used alone or in conjunction with a Signal Word or supplemental text to give a specific warning about the pipe’s contents or to add any additional information that may enhance safety or facilitate identification and maintenance.

To add a pictograph/symbol to a marker, first Double-Click on the displayed marker and click [Edit Graphics>>] button.

Edit the Pipe Marker Graphics dialog box appears.

use the scroll bar to review the list of symbols. Highlight the symbol to see illustration of symbol.



Highlight the desired pictograph in the Available list box. Double-Click which automatically selects the pictograph/symbol to the Selected list. When using single click also click the “>>” add button above the illustrated pictograph/symbol. The pictograph will be placed in the Selected list. up to three pictographs can be added to any marker. Click [OK].

To remove a pictograph added to the selected box either Double-Click it or highlight it and click the “<<” remove button below the illustrated pictograph.

Example: Marker with symbol



Pictograph Symbol ListArrow BothArrow DownArrow Down FullArrow LeftArrow Left FullArrow RightArrow Right FullArrow upArrow up FullBioHazard (AnSI)Chevron Double LeftChevron Double RightChevron LeftChevron RightCorrosion (GHS)Electric Bolt (AnSI)Electric Hand (AnSI)Environment (GHS)Exclamation Mark (GHS)Exploding Bomb (GHS)EyewashFire Extinguisher 1Fire Extinguisher 2Fire Hose (AnSI)First Aid CrossFlame (GHS)Flame Over Circle (GHS)Gas Cylinder (GHS)Health Hazard (GHS)ReactiveSecure CylindersShowerShower_EyewashSkull & Crossbones (GHS)TelephoneToxicWarning Alert **Water Reactive

NotE: GHS Symbols require a black symbol on a white background with a red diamond frame. The black symbols are being provided to add to a marker but K-Sun® suggests using MaxiLabel®Pro Ver 5.0 to create your GHS symbol.

** Warning Alert – AnSI Z535.2011 4.11 Safety Alert Symbol – Indicates a hazard. It is composed of an equilateral triangle surrounding an exclamation mark. The symbol shall not be used to alert persons to property damage – only accidents.



Usage Guidelines - Symbols[AnSI Z535.2-2011 A2]When a safety symbol is used as part of a multi-panel safety sign, label and tag format, described in the AnSI 535.2, AnSI 535.4 and AnSI 535.5 standards, it usually consists of a safety black image on a white background, without color or surround shape.

Two exceptions where surround shapes are required are the Safety Alert Symbol (exclamation mark with an equilateral triangle) and the Prohibition Symbol (within a circular band with a diagonal slash.)



Import Pictograph/SymbolClick [Import] button under Available Pictograph (Symbols).

Locate the desired image (.bmp, wmf, emf format). Click [Open].

The pictograph/symbol appears in available symbols. Double-Click to select for marker. up to 100 images, pictographs/symbols can be saved.

To delete an image from Available Pictograph Symbols library, highlight the symbol and choose Delete. Deleting imported symbols also deletes them on custom markers. Symbols that come with the program cannot be deleted.



Creating QR Code or Data Matrix BarcodePipe marker standards make no mention of the inclusion of bar codes on pipe markers. use QR Codes or Data Matrix Barcodes to add links to SDS sheets or maintenance records.

Begin by choosing QR Code button or DataMatrix button on the Edit the Pipe Marker Graphics dialog box.

Add your code information. Click [OK].

Example for QR Code



The QR code now appears in Symbols. Click on the >> Button to add to marker. Click [OK].

Example: QR Code added to marker.



If you add symbol you can delete:

You cannot delete the permanent set of symbols

up to 100 Symbols can be added.If you delete a symbol that was added to a saved pipe marker the symbol will be deleted on the pipe marker.



4.3 Adding Company Information to MarkerAdd company information (or other contact information) to a marker next to copyright information.From the main screen, click [Options], [Company Information].

Type your company name (up to forty characters), and click [OK].

Company information is only available in the same size as K-Sun® copyright information.

For larger text or to add a logo, create a .bmp with these elements and import as a symbol to the marker.

For Pipe Size 10> company information cannot be added.


41Creating a new Pipe Marker

Creating a New

Pipre Marker

5. Creating a New Pipe MarkerCreate a custom pipe marker from scratch or edit an existing marker to custom status with K-Sun® PipeMarker™ V8.

Click on PipeMarkers, New, to start from scratch. The Edit the Pipe Marker Text dialog box appears.

Choose Color (Background field color). In the English text box add text. The Font Size box is not dimmed out. Only in New will you have this option.

Note: Custom pipe markers may not meet AnSI/ASME guidelines but provide a way to create additional markers and signage.

After creating the custom marker, Choose PipeMarkers, Save. The Save Pipe Marker dialog box appears. Save Marker to Custom 1, 2, 3, 4, or 5. Choose Yes.

The marker will be saved, listing Field Color, Pictograph, Signal Word and Legend.

To recall, choose Custom Category(1-5) and review markers within the category.

To delete, choose Marker and display on screen. Choose Pipemarkers, Delete.

Information screen will appear. Delete this Pipe from ‘Custom Created Pipe’ category? To Delete Choose Yes.

To print, choose PipeMarkers, Print. Review the usage guideline. Choose number of markers to print. Click [OK].

The printer dialog box appears. Click [OK]. Confirm Tape Width. Click [OK].

42Saving Custom Pipe Markers

Saving Custom Pipe M

arkers

6. Saving Custom Pipe MarkersSave a new or edited pipe marker in one of the 5 Custom Categories. Click on PipeMarkers, Save, and select one of the 5 Custom categories in which to save the marker. Each custom category can hold up to 200 markers.

Pipe markers saved will be added to the bottom of the list in the Custom category and like all other stored pipe markers, will be identified by their Field Color, Pictograph, Signal Word and Legend. A custom pipe marker can be deleted. Remember, if you delete a symbol/pictograph, the symbol and/or pictograph will be deleted from the custom designed pipe marker.

Delete Custom Pipe MarkerCustom pipe markers can be deleted in K-Sun® PipeMarker™ V8 by highlighting the custom pipe marker to be deleted in the pull-down list of Custom Pipe markers, and selecting the Delete option in the PipeMarkers menu.

43IIAR Markers

IIAR M

arkers

7. IIARK-Sun® PipeMarker™ V8 includes component creation of pipe markers based on the requirements for Identification of Ammonia Refrigeration Piping and System Components Bulletin 114 dated September 1991.

Choose Category IIAR

IIAR AbbreviationsIIAR has approved abbreviations for names commonly given to piping in ammonia refrigeration systems. They are:BD Booster DischargeCD Condenser DrainDC Defrost CondensateES Economizer SuctionHGD Hot Gas DefrostHPL High Pressure LiquidHSD High Stage DischargeHSS High Stage SuctionHTRL High Temperature Recirculated LiquidHTRS High Temperature Recirculated SuctionLTRL Low Temperature Recirculated LiquidLTRS Low Temperature Recirculated SuctionLIC Liquid Injection CoolingLSS Low Stage SuctionRV Relief VentTSR Thermosyphon ReturnTSS Thermosyphon SupplyThe IIAR category contains 27 pre-designed markers.

Editing IIAR markerTo use other abbreviations that may be acceptable in your workplace choose a marker closest to your desired marker.

44IIAR Markers

IIAR M

arkers

Double-Click on the marker.

Edit the IIAR Marker dialog screen appears. under ABBREV (Abbreviation) Choose Custom and add your abbreviation (up to 5 letters).

Note: use the Edit the IIAR to create a custom IIAR marker but you cannot save a custom IIAR marker.

Note: IIAR standards do not specify marker sizes for pipes less than ¾” diameter and recommend using tags for small pipes. Tags may be used to mark valves and components. IIAR pipe markers cannot be printed out in tag format.

45IIAR Markers

IIAR Physical StateIIAR has approved abbreviations and color-coded bands to identify the physical state of the refrigerant. They are:

LIQ Orange Liquid VAP Sky Blue Vapor

For pipes that contain both the liquid and vapor states of the refrigerant, both should be used.

IIAR M

arkers

46IIAR Markers

IIAR M

arkers

IIAR PressureIIAR markers include an indication of refrigerant pressure. Pressures over 70 psig, under normal operating conditions are considered to be HiGH pressure. Pressures equal to or less than 70 psig, under normal operating conditions, are considered to be LoW pressure. These are indicated by the word HIGH in a red band or the word LOW in a green band.

47IIAR Markers

Printing IIAR MarkersK-Sun® recommends printing IIAR markers with this method using the K-Sun® PEARLabel® 400iXL or K-Sun® PEARLabel® 360.

Print entire label with black ribbon and yellow tape.

Choose PipeMarkers, Print.Review usage Guidelines.At the Print Dialog Box choose [OK].The entire marker prints.

now print the color sections using separate printing.

Choose PipeMarkers, Separate PrintThe Select Separate Print Screen appears. Choose LIQ and PRESSuRE

IIAR M

arkers

48IIAR Markers

Click [OK].The Print dialog box appears. Choose [OK].A Tape Change dialog box appears. Review and change supplies as necessary.Choose [Confirmed].

An example showing Separate Component Printing:

Alternative Printing method using Separate Printing.It is possible to print out each section of the label and then paste each section to the next section.

NotE: use Separate Printing to create a set of stock labels or components that may need replacing.

Illustrated PEARLabel® 360 1/2 cut printing.

To create Stock Labels:Choose Printer, Pipe Size.Choose Separate Printing.Check Section only. (for instance LOW)At number to print, change quantity to number needed.

IIAR M

arkers

49Medical Gas Markers

Medical G

as Markers

8. Medical Gas MarkersPrinting Medical Gas Markers-Stripe Background+ Black Boxed TextNotE: Printing Medical Gas Markers (with stripe or checkerboard backgrounds) will require printing two labels. One for creating the background pattern and a separate label for the text that will be applied over the background pattern.

Medical Gas Marker Non-Medical and Level 3 Vacuum requires a White and Black Diagonal Stripe with black-boxed text on a white background. Make this marker with K-Sun® PEARLabel® 400iXL and 360 printers.

To create this pipe marker use the following steps.

Open the program to Category-Medical Gasses. Choose Pipe Legend Non Medical Vacuum. Choose Printer, Pipe Size, Tape Width and add Flow Marking if desired.

now Choose PipeMarkers Print. usage Guidelines appear. Make note of the Marker Size Length.For this example it is 8.9 inches. Cancel Printing.

Choose Pattern Printing. Choose Diagonal Stripe, Regular and make length 9”. Click [OK]. Confirm that in your K-Sun® PEARLabel® 400iXL printer Black Ribbon, White Tape supplies. Click [OK]. Confirm Supplies width. Click [OK]. Print Preview appears. Click the printer icon.


Medical G

as Markers

Open MaxiLabel® Pro Ver 5.0. In K-Sun® PEARLabel® 360 put in 24mm Black on White Tape.

For Pipe Size ¾-1 ¼” Height of Letters is ½” (See Height of Letters) Choose Arial font and 48 pt.(This is the default font size for 24mm supply with K-Sun® PEARLabel® 360 printer)

Type Text. Set Text properties Bold, Tall, narrow Character Spacing. using the Line Tool draw a box around text. Set line properties to .03. Insert Arrow Symbol. Print.


Apply label to top of diagonal stripe label.

Example: non Medical Vacuum Marker

Height of LettersARIAL FONT- TAPE/TEXT SIZE COnVERSIOn FOR PIPE MARKER 48PT ½” for Pipe Size ¾” to 1 ¼” Outside Diameter72PT ¾” for Pipe Size 1 ½ to 2” Outside Diameter

Medical G

as Markers


Medical G

as Markers

Printing Medical Gas Markers-Stripe Background + Black TextNotE: Printing Medical Gas Markers (with stripe or checkerboard backgrounds) will require printing two labels. One for creating the background pattern and a separate label for the text that will be applied over the background pattern.

Medical Gas Marker Non-Medical Air requires a Yellow and White diagonal stripe background with Black Text. Make these markers with the K-Sun® PEARLabel® 400iXL printer.


Open the program to Medical Gasses Category. Choose Pipe Legend Non Medical Air.Choose Printer, Pipe Size, Tape Width and add Flow Marking if desired.

In K-Sun® PEARLabel® 400iXL place Black Ribbon, Clear Tape.Before printing make note of length of marker in usage Guidelines. Print.

In K-Sun® PEARLabel® 400iXL Change to White Ribbon, Yellow Tape. now choose Pattern Printing. Diagonal Stripe. Set Length.

Click [OK]. Print. note print preview will not show colors correctly.


Apply Text over Yellow Diagonal Stripe.Example: non Medical Air Marker

Medical G

as Markers


Medical G

as Markers

Printing Medical Gas Markers-Checkerboard Background + Black TextNotE: Printing Medical Gas Markers (with stripe or checkerboard backgrounds) will require printing two labels. One for creating the background pattern and a separate label for the text that will be applied over the background pattern

Medical Gas Marker Laboratory Air requires a Yellow and White Checkerboard background with black text. Make this markers with the K-Sun® PEARLabel® 400iXL.Choose Medical Gasses Category and then Pipe Legend [Laboratory Air]. Choose Printer, Pipe Size, Tape Width and add Flow Marking if desired.

In K-Sun® PEARLabel® 400iXL place Black Ribbon, Clear Tape. Print. Before printing make note of length of marker in usage Guidelines. Print.

In K-Sun® PEARLabel® 400iXL Change to White Ribbon, Yellow Tape. now choose Pattern Printing. Checkerboard Stripe. Set Length.Click [OK]. Print. note print preview will not show colors correctly.


Apply Text over Yellow Checkerboard Background.Example: Laboratory Air Marker

Medical G

as Markers


Medical G

as Markers

Printing Medical Gas Markers-Checkerboard Background+ Black Boxed TextNotE: Printing Medical Gas Markers (with stripe or checkerboard backgrounds) will require printing two labels. One for creat-ing the background pattern and a separate label for the text that will be applied over the background pattern

Medical Gas Marker Laboratory Vacuum requires a White and Black checkerboard with black-boxed text on a white background. Make this marker with K-Sun® PEARLabel® 400iXL and 360 printers.


Open the program to Category-Medical Gasses. Choose Pipe Legend Laboratory Vacuum. Choose Printer, Pipe Size, and Tape Width. Add Flow Marking if desired.

now Choose PipeMarkers Print. usage Guidelines appear. Make note of the Marker Size Length.For this example it is 8.9 inches. Cancel Printing.Choose Pattern Printing. Choose Checkerboard Stripe, 4 and make length 9”. Click [OK].


Medical G

as Markers

Confirm that in your K-Sun® PEARLabel® 400iXL printer Black Ribbon, White Tape supplies. Click [OK]. Confirm Supplies width. Click [OK]. Print Preview appears. Click the printer icon.

Open MaxiLabel® Pro Ver 5.0. In K-Sun® PEARLabel® 360 put in 24mm Black on White Tape.

For Pipe Size ¾-1 ¼” Height of Letters is ½” (See Tape size, Text grid for Arial font below) Choose Arial font and 48 pt. (This is the default font size for 24mm supply with K-Sun® PEARLabel® 360 printer)

Type Text. Set Text Properties Bold, Tall, narrow Character Spacing. using the Line Tool draw a box around text. Set line properties to .03.Insert Arrow Symbol. Print.

Apply label to top of Checkerboard label.Example: Laboratory Vacuum Marker

Height of LettersARIAL FOnT- TAPE/TEXT SIZE COnVERSIOn FOR PIPE MARKER48PT ½” for Pipe Size ¾” to 1 ¼” Outside Diameter72PT ¾” for Pipe Size 1 ½ to 2” Outside Diameter

58Pattern Printing

Pattern Printing

9. Pattern Printing-Arrow TapeTo print Arrow Tape, Diagonal Stripe or Checkerboard Tape choose Pattern Print button.The Pattern Print Dialog box will appear.

Note: Only for Pattern Printing Print Preview is automatically turned on to provide a visible display when creating a pattern marker.

Arrow tape Determine your style and select length (up to 90 inches). Click [OK].The Print dialog box appears. Click [OK]. The Print Preview screen appears. Review. To Print click [Printer icon] or to cancel click Red [X].

59Pattern Printing

Pattern Printing

Pattern Printing - Diagonal Stripe TapeDetermine your stripe style and set length up to 90 inches. Click [OK].

The Print dialog box appears. Click [OK].

The Print Preview screen appears. Review. To Print click [Printer icon] or to cancel click Red [X].

60Pattern Printing

Pattern Printing

Pattern Printing - Checkerboard TapeDetermine the number of checks (use drop down box to select). Click [OK].Select Length up to 90 inches. Click [OK].

The Print dialog box appears. Click [OK].

The Print Preview screen appears. Review. To Print click [Printer icon] or to cancel click Red [X].

62Regulation Reference

10. REGULATION INFORMATIONANSI/ASME StandardsThe relevant AnSI/ASME standards for pipe markers and tags are: AnSI/ASME A13.1-2007 Scheme for the Identification of Piping Systems AnSI Z535 2011 Color Chart AnSI Z535.1-2006 (R2011) Safety Colors AnSI Z535.2-2011 Environmental and Facility Safety Signs AnSI Z535.3-2011 Criteria for Safety Symbols AnSI Z535.4-2011 Product Safety Signs and Labels AnSI Z535.5-2011 Safety Tags and Barricade Tapes (for Temporary Hazards)These standards are subject to change. Contact ASME at: ASME American Society of Mechanical Engineers Two Park Avenue new York, nY 10016-5990 Phone: 800-843-2763 (uS Canada) 001-800-843-2763 (Mexico) 973-882-1170 (outside north America) www.asme.orgContact AnSI at: www.ansi.org Washington DC Headquarters 1899 L Street nW, 11th Floor Washington DC 20036 Phone 202-293-8020 Fax 202-293-9287 new York City Office (Operations) 35 West 43rd Street, 4th Floor new York, nY 10036 Phone 212-642-4900 Fax 212-398-0023

CFR Code of Federal Regulations The portion of the Code of Federal Regulations (CFR) that is relevant to pipe markers is 29 CFR part 1910.145.

The CFRs are subject to change. Contact the Government Printing Office at:

For questions and to place orders, contact the Government Printing Office Customer Contact Center.Our Hours of Service: Expert operators are available to answer you from 8:00 a.m. to 5:30 p.m. Eastern Time, Monday through Friday (except u.S. Federal Holidays).

PHONE: uS and Canadian customers: call toll-free: 1.866.512.1800. Washington, DC area or International customers: call +1.202.512.1800.

EMAIL: Send an email to [email protected]

FAX: Print & fill out order form and fax to: 202.512.2104

MAIL ORDERS: Print & fill out order form and mail to:u.S. Government Printing OfficeP.O. Box 979050St. Louis, MO 63197-9000Available on line at osha.gov

Regulation Reference

63



CGA Compressed Gas Association The relevant CGA standard for pipe markers is CGA C-9-2004 Reaffirmed 2008 Standard Color Marking of Compressed Gas Containers for Medical use

Compressed Gas Association14501 George Carter Way, Suite 103Chantilly VA 20151Phone 703-788-2700Fax 703-961-1831www.cganet.com

IIAR International Institute of Ammonia Refrigeration Bulletin #114 Guidelines for Identification of Ammonia Refrigeration Piping and System Components.

Standards are subject to change. Contact IIAR at:International Institute of Ammonia Refrigeration1001 n. Fairfax Street Suite 503Alexandria VA 22314703-312-4200www.iiar.org

NFPA National Fire Protection Association Some relevant nFPA standards for pipe markers and tags are:

nFPA 70 national Electrical Code (nEC) nFPA 99C Health Care Facilities These standards are subject to change. Contact nFPA at: national Fire Protection Association 1 Batterymarch Park PO BOX 9101 Quincy MA 02269-9101 Telephone: 1-800-344-3555

64Technical Support

Technical Support

11. K-Sun® Technical SupportIf you have a question or suggestion about the K-Sun® PipeMarker™ V8 program readme please contact us.

Phone: 715-247-4440 800-622-6312x214Fax: 715-247-4003 800-522-9108Email: [email protected]

When calling, be at the computer the software is installed on and have the following information available:

Date of Software purchase Windows® Operating System Printer type or model Printer driver version Any messages that appeared on your screen Details about what happened when the problem occurred

When emailing, include the information above and convenient time for calling.

Technical Support is provided M-F 8AM-4PM uS Central Time

pipemarker v8 manual - epson labelworks pxlabelworks.epson.com/wp-content/uploads/2017/07/... ·...

Documents