pixel preview book of heroes volume 1 (6780422)

8/9/2019 Pixel Preview Book of Heroes Volume 1 (6780422)

1/7

P i x e l

P r e v i e

w

aela Keil (order #6780422)


2/7

Art, ext and layout: Zigmund Kawakami

Computer Users: If you have access to the internet please visit Octopus Apocalypseonline at the official umblr, Facebook , and Google+ pages.

Pixel Preview

Book of Heroes Volume 1

OCAP-PXD-X01: Pixel Preview: Book of Heroes Volume 1 ©2013–2015 Octopus Apocalypse. All rights reservedTis material is protected under the copyright laws of the United States of America. No part of the material orartwork herein may be reproduced, stored in a retrieval system, or transmitted in any form by any means, elec-tronic, mechanical, or otherwise, without the express written permission of Octopus Apocalypse, except for wherespecifically otherwise noted.


http://octapoc.tumblr.com/http://www.facebook.com/OctopusApocalypsehttps://www.google.com/+Octopusapocalypsehttps://www.google.com/+Octopusapocalypsehttp://www.facebook.com/OctopusApocalypsehttp://octapoc.tumblr.com/


3/7

Required Materials: All miniatures in this set can be assembled with the following materials.Glue Stuck: An extra strength glue stick is preferable. Any low moisture glue will work well too.Scissors: All Paper Dungeon miniatures can be cut out with common household scissors.

Optional Materials: Te following materials may be required for optional assembly steps, but are not required.Hobby Knife: Experienced users may wish to cut miniatures out with a hobby knife.ape: Clear tape is used in the optional step of reinforcing the miniature’s base tab.Black Felt ipped Marker: Used for edging the miniatures.

Tis document has 3 major sections:

Instructions: Tis section contains information on Required Materials, Basic Miniature Assembly and MountedMiniature Assembly.

Catalog: Te catalog shows the miniatures included in this set along with instructions for using the simpleminiature selection sheet

Miniature Selection Sheet: Tis is where you select and print your miniatures. Make sure to read the section onUsing the Miniature Selection Sheet before using for the first time.

Note 1: Tis document has been bookmarked for your convenience. All sections can be accessed via the

bookmarks panel

Note 2: Bases and base assembly instructions can be found in the Pixel Mini Base Station document.

Using Tis Document

Required Materials



4/7

Basic Miniature Assembly

Step 1:

Cut out the miniature as shown. When cutting, cut along the bottom and sides of the base tab.

Step 2:Fold the base tabs outward, cutting along the top of the base tab up to the black outline will make this—as well as s3—easier. Next fold the miniature along the fold line, use the base tabs or a light source to make sure the sides are ev

Step 3:Glue the two sides together, when applying glue make sure to cover the entire area of the black outline. Once the ghas dried, cut out the miniature along the black outline

Edging (Optional):With a black felt tipped marker, fill in the white edge of the figure—see above image for example.

Reinforcing and Shaping the Base ab (Optional):Apply a small piece of tape to the bottom of the base tab and trim. You may also wish to cut the ends of the base tabpoints, this makes inserting the miniature into the base easier.

Final Assembly:Insert the miniature into the base. If you’re having trouble, flex the base to open the slot wider.Once your miniature is completed, proceed to adventure.



5/7

Mounted Miniature Assembly

Step 1:Cut out the mounted miniature as shown and fold along the fold line, due to the lack of base tabs it may be especi

useful to hold the miniature up to a light source to make sure it’s properly aligned. ake special note if there are 2 dots on one side of the miniature. Tis indicates that as the larger side of the figure, when cutting it is important to won the large side or you may cut off parts of the miniature.

Step 2:Glue the folded miniature together from the glue line up (gray line running through miniature), If miniature is glubelow the glue line, it will not sit properly on the mount.

Step 3:Cut out the miniature, if a large side is indicated cut out along that side.

Step 4:urn over the figure, the opposite side may require extra trimming. rim off remaining white areas on the smaller sif needed and edge if desired.

Step 5:Place your completed miniature on your chosen mount and proceed to adventure.



6/7

The full version of Book of Heroes Volume 1 includes all 34 miniatures pictured below

Chestnut Horse

5

Half-Orc Rogue

4

Half-Elf Cleric

3

Dwarf Fighter

2

Te following page is the miniature selection sheet. User is permitted to make unlimited printed copies of the materialscontained within for personal use.

Human Wizard

1

Tis product uses the Simple Miniature Selection Sheet, a simplified version of the Miniature Selection Sheet found in other PixelDungeon Products.

o use the Simple Miniature Selection Sheet, find the number of the miniature you wish to print—found directly above theseinstructions—and click on that number.

Click the miniature the cycle through the available variants. Te 4 character miniatures in this set include a standing and a mounted variant. Te Horse includes a standard and barded variant.

o clear out the selected miniature from a miniature slot, simply click the clear button. All buttons are non-printing.

Note: Due to its size, multiple horses should not be printed in adjacent miniature slots and are not available on the two right-most slots.



7/7

Clear

54321

Clear

54321

Clear

54321

Clear

4321

Clear

4321

Clear

54321

Clear

54321

Clear

54321

pixel preview book of heroes volume 1 (6780422)

Documents