pleatfil™ pgp - techno filter€¦ · pleatfil™ pgp pleated polypropylene filter cartridge...
TRANSCRIPT
PLEATFIL™ PGPPleated polypropylene filter cartridge
Pleatfil™ PGP filter cartridges are cost effective, Beta
5000 absolute rated pleated polypropylene filters.
The fully welded construction of PGP grade filters,
with no resins, binders, or adhesives, makes them
particularly suitable for chemical, food & drink,
and high-purity water filtration applications where
chemical compatibility and minimal levels of
extractables are crucial. Pleatfil™ liquid filter cartridges
are fully validated and recorded in the product validation
guide for Pleatfil™.
PLEATFILTM PGP
TM
using the industry standard single pass OSU-F2 test
procedure with ISO 12103 part 1 A2 Fine and A4
Coarse test dust in water.
Manufactured in Europe from 100% virgin
Thermal bonded construction eliminates the
requirement for adhesives, maintaining product
integrity in demanding applications and minimising
Food & Biological Safety
All materials conform to the relevant requirements of
FDA CFR21 part 177, USP Plastics Class VI and EC
1935/2004.
range of applications, and are used for the
end products.
Pleated polypropylene filter cartridge
Removal ratings from 0.2 to 100 micron
One-piece construction up to 40”
Fully welded construction
High surface area, up to 0.6 m²/10”
Full range of bonded end caps available
Low pressure drop
Long life, high dirt-holding capacity
Materials conform with FDA 21CFR part 177,
and EC 1935/2004
A full validation guide is available upon request
• •• ••• • • •••
•
Retention characteristics
have been determined by a single-pass technique
using suspensions of ISO 2103 Part 1 A2 Fine and
A4 Coarse test dust in water.
TM
Media
Code
PGP020
PGP050
PGP01
PGP02
PGP05
PGP10
PGP25
PGP50
PGP75
PGP100
99.98%
Bèta 5000
0.20
0.50
1.0
2.0
5.0
10.0
25.0
50.0
75.0
100.0
99.90%
Bèta 1000
< 0.20
0.45
0.75
1.7
3.5
8.0
15.0
29.0
55.0
85.0
99%
Bèta 100
-
0.35
0.55
1.5
2.0
4.8
12.0
25.0
40.0
75.0
90%
Bèta 10
-
0.3
0.4
1.2
1.5
2.5
8.0
15.0
35.0
70.0
Dimensions (nominal)
Outside Diameter: 69 mm
Inside Diameter: up to 32 mm
Lengths: 5” to 40”
Operating Conditions
Recommended Maximum ∆P PP core 4.0 bar @ 20 °C
PP core 1.2 bar @ 65 °C
Recommended change-out
PP core 2 bar ∆P @ 20 °C
Maximum service life 12 months
Maximum continuous operating T:
80 °C with PP centre core
Sterilisation and sanitisation
Hot water: 90 °C for 30 minutes @ max 0.2
bar dp
Materials of Construction
Filter Medium: PolypropyleneDrainage layers: PolypropyleneInner Core: PolypropyleneOuter Core: PolypropyleneEnd Caps: PolypropyleneGaskets & O-rings: various materials
Technical Data Pleatfil TM PGP
A comprehensive range of thermally welded end caps are available to suit most existing installations.
:
solutions with a viscosity of 1 centipoise.
20
15
10
5
00 5 10 15 20 25
Flow (l/min)
Dif
fere
nti
al P
ress
ure
(m
bar)
PGP 25 / 50
PGP 75 / 100
Viscosity (CPS) 1 100 200 400 600 800 1000 1500 2000 4000 6000 8000 10000
Conversion factor 1 .85 .58 .35 .25 .17 .16 .11 .08 .05 .035 .026 .021
PGP 10
Fusion bondingInner coreSupport layerFilter mediaDrainage layerOuter supportTop end cap / adaptor
1
2
3
4
5
6
7
8
4
5
5
6
3
28
7
2
1
Dif
fere
nti
al P
ress
ure
(m
bar)
60
50
40
30
20
10
00 5 10 15 20 25
PGP020
PGP050
PGP01PGP02
Flow (l/min)
PGP05
PLEATFILTM PGP
High-quality cartridge construction ensures
consistent performance
melt-blown polypropylene medium to minimise
The structurally stable medium eliminates the risk of
channelling and particle unloading even under impulse
materials are carefully pleated and seam-bonded to avoid
Quality Assurance & Traceability
environment by staff fully gowned to minimise any risk of
contamination during production.
Filter Housings
Filter housings are subdivided into two main categories:
Housings for (pressurised) air & other gases.
Address
Techno Filter B.V.
Johan Enschedeweg 72
1422 DR Uithoorn
Contact
Telephone: +31(0)297 - 524 131
Faxnr: +31(0)297 - 524 333
CoC: 54868718
VAT registrationnr: NL 851471559B01
The Netherlands
the European regulations of the Pressure Equipment
and vacuum applications.
Techno Filter designs and supplies:
sanitary and industrial grades.
“lenticulars” in sanitary grades.
industrial grades.
from 0.4 up to appr. 1250 microns.
PED 97/23 standard: categories III and IV. This means
or questions about custom housings, please contact
Techno Filter.
•
•
•
•
•
•
•
PGP00.1