plows - parts for trucks

www.danielsplows.com

844.BLU.PLOW

P L O W S

PULL PLOWPULL PLOW

(844.258.7569)

Two plows are better than one!

Incredibly Efficient

P L O W S 844-BLU-PLOW • www.danielsplows.com

The Daniels Pull Plow doesn’t replaceyour front-mounted plow - it complementsit by cleanly removing snow and ice fromthose hard-to-plow areas that your frontmounted plow simply isn’t designed toefficiently handle.

Thanks to 2,000 lbs. of downwardhydraulic pressure, residential driveways,loading dock areas and circle drives arecleared in record time - right down to thepavement! Since your snow removalactions are always done while movingforward, it’s much safer thanbackdragging snow into acrowded, busy street!

The Daniels Pull Plow fits virtuallyany 4WD vehicle equipped witha 2" receiver-type hitch.

Thanks to the patentedSPEEDHITCH™ — hook-up isfast and easy!

Simply connect the SPEEDHITCH™

to the truck’s standard 2" receiver-

type hitch and connect chain to the

truck frame.

Connect the drawbar arms to the

“ears” on the T-bar, then connect

the horizontal arm.

The entire plow assembly can be

removed from the truck in under

30 seconds, freeing the rear of

the truck for other uses.

Model Number 7201* 8001 9001 9601Plow Width 72" 80" 90" 96"

Overall Dimensions(6') (6'-8") (7'-6") (8')

Material Specifications

Weight (lbs.) 275 300 325 350

Height 19" 19" 19" 19"

Moldboard 8 gauge 8 gauge 8 gauge 8 gauge

Side plates 3/8" 3/8" 3/8" 3/8"

Draw bar arms 1" x 2" 1" x 2" 1" x 2" 1" x 2"

3/8" x 5" 3/8" x 5" 3/8" x 5" 3/8" x 5"Cutting edge - AR400

Poly version available(non-reversible)

* Limited Availability

Pull Plow Specifications

1

2

3

External HydraulicContainment Boxes arestandard for mounting thepower units with the plowat the back of the truckinstead of in the enginecompartment. TheHydraulic Containment Boxcomes supplied with a wireharness which runs to thevehicles battery and acontrol switch into the cab.Clean, contained, out ofthe way, and accessible formaintenance. Easilyinstalled and removed withthe lift assembly.Does not affect the fastand easy 1, 2, 3 Hook Up.

HYDRAULICS: ALL MODELS

CLEARANCES: ALL MODELS

Cycle time: 2.5 secondsOil capacity: 2 qts.Fluid type: Dexron Trans fluidDown pressure set at 2,000 lbs.

Rear of bumper to end of plow: 26"Maximum lift height-side plates: 12"Maximum lift height-rear of plow: 18"

Cylinder rods are black nitride treated for5x corrosion resistance and extreme durability

RECOMMENDED APPLICATION80“ - Jeep and small chassis trucks90" - 1/2 ton and full-size trucks96" - 3/4 and 1 ton trucks (dually)

Daniel’s “NEW” MountBar, pins into the 2”Reciever Hitch and issecured by attachinghooks to the truckframe.

No more welding tothe hitch. Installationtime is cut in halfwithout sacrificingstrength or the easyon and off.


844.BLU.PLOW

P L O W S

Industry’s Most Durable & EfficientStraight Blade Plow

STRAIGHT BLADESTRAIGHT BLADE

(844.258.7569)

Daniels Plowsoffers a straightblade in theperfect size formounting to skidsteers!

Provides the same incredible high snowplowing efficiency for all makes and sizesof skid steer.

Use one plow to both push and stack snow.

Eliminate the need for multiple pieces ofequipment at the job site.

Straight Blade SpecificationsIncredibly Efficient Model Number 2710 2712 2714*

Plow Width 10' 12' 14'

Plow Construction

Width Hydro-Turned 8' 2" 9' 10" 11' 6"

Moldboard:

Material 7 ga. 7 ga. 7 ga.

Height 27" 27" 27"

Vertical Reinforcing Ribs:

Material 1/4" 1/4" 1/4"

Number 7 9 11

Hinged Tripping Points 5 5 5

Trip Springs 4 4 4

Shipping Weight 1100 lb. 1250 lb. 1475 lb.

Wear Edge - Reversible 5/8" x 8" 5/8" x 8" 5/8" x 8"(Two Sections)

Keeps snow in front of the blade!

Prevents snow from spilling over the sides of the plow

Features an exclusive, spring-loaded trip design!

PATENTED PUSHER KIT

STANDARD FEATURES

AVAILABLE OPTIONS

•

• Double-acting cylinders withmaximum stroke at 35 degrees.

• 2 Pin Mounting Plate for Skid Steers

• Swivel Plate and pivoting backing plate

• Pusher Kit • Skid Shoes

• Curb Guards

Hydraulic cylinder rods are black nitridetreated for 5x corrosion resistance andextreme durability.

• Reversible AR400 steel cutting edges.

Provides Skid Steers with Unprecedented Efficiency

P L O W S

OptionalCurb Guard

2 Pin PlateStandard Option

844-BLU-PLOW • www.danielsplows.com

* Limited AvailabilityPusher Kit available on any size.


844.BLU.PLOW

P L O W S

(844.258.7569)

WING PLOWWING PLOWTHE

Incredibly Efficient

PATENTED PUSHER KIT

P L O W S 844-BLU-PLOW • www.danielsplows.com

The Daniels Wing Plow canbest be described in twowords - Incredibly Efficient!

By using one plow to bothpush and stack snow, the needfor multiple pieces ofequipment at the job site iseliminated.

The patented, fold-back wingdesign lets you reduce theplow’s size by up to 50% forunsurpassed maneuverability,ease oftransport,and whenconditionscall for asmallerplow size.

Model Number 3412! 3414 3416 3418 3420

Plow Construction

Plow Width 12' 14' 16' 18' 20'

Center Plow 8' 10' 10' 12' 12'

Each Wing 2' 2' 3' 3' 4'

Width Hydro-Turned* 6'9" 7'6" 8'6" 10'6" 10'6"

Width Hydro-Turned** 10' 11'6" 13'1" 14'8" 16'4"

Moldboard:Material 10 ga. 10 ga. 10 ga. 10 ga. 10 ga.Height 34" 34" 34" 34" 34"

Vertical Reinforcing Ribs:Material 1/4" 1/4" 1/4" 1/4" 1/4"Number 10 11 11 13 13

Hinged Tripping Points 5 5 5 7 7

King Pin Diameter 2 1/2" 2 1/2" 2 1/2" 2 1/2" 2 1/2"

Trip Springs 2 2 4 4 6

Shipping Wt. (lbs.) 2100 2300 2500 2800 3100

Wear Edge 5/8" x 8" 5/8" x 8" 5/8" x 8" 5/8" x 8" 5/8" x 8"

*With Wings folded ** With Wings open

(Reversible)

Wing Plow Specifications

STANDARD FEATURES

AVAILABLE OPTIONS

•

• Double-acting cylinders w/max.stroke at 35 degrees

• Cushioning Relief Valve

• Backing Plate and Standard Ears

• Double Wing Hinge Design

• Reversible Steel Wear Edges

• Patented Pusher Kit

• Curb Guards

• Skid Shoes

Hydraulic cylinder rods are blacknitride treated for 5x corrosionresistance and extreme durability.

Featuring our exclusivespring-loaded trip design

Keeps snow in front of the blade

Prevents snow from spillingover the sides

Increases capacity up to 45%

Available in all sizes

Larger Sizes Built To OrderUpon Request

Recommended Wheel Loader Size

14' 10,000 to 15,000 lbs.

16' 18,000 to 23,000 lbs.

18' 20,000 to 25,000 lbs.

20' 23,000 to 32,000 lbs.Wing Plow with pusher kitsadd 3,000-5,000 lbs.

! Limited Availability


844.BLU.PLOW

P L O W S

PINNACLE PUSHERPINNACLE PUSHER

(844.258.7569)

844-BLU-PLOW www.danielsplows.com

Incredibly EfficientIncredibly Efficient• Proven over ten years in the harshest

conditions of Alaska, including the North Slope.

• Overbuilt and fully-welded, this plow pushes snow, pulls snow from curbs, loading docks, garage doors, etc.

Key Features• Operators that switched from

traditional box plows have realized increased efficiencies up to 40%.

• The Pinnacle Pusher uses rubber and steel cutting edges for all types of snow and ice conditions.

Pinnacle Pusher Specifications

• Floating detachable mount system.

• Extended skis available on request.

• Sectional 1” thick reinforced belted edge allows for quick change-out and performance on uneven surfaces.

Model Number PP-24-6 PP-24-8 PP-36-8 PP-36-10 PP-36-12 PP-42-10 PP-42-12 PP-42-14

Height 24” 24” 36” 36” 36” 42” 42” 42”Width 6’ 8’ 8’ 10’ 12’ 10’ 12’ 14’Cubic Volume 19 Cu ft. 25 Cu ft. 57 Cu ft. 71 Cu ft. 85 Cu ft. 96 Cu ft. 115 Cu ft. 134 Cu ft.Plow ConstructionMoldboard 11 ga 11 ga 11 ga 11 ga 11 ga 11 ga 11 ga 11 gaVertical Ribs 3/4” & 3/8” 3/4” & 3/8” 3/4” & 3/8” 3/4” & 3/8” 3/4” & 3/8” 3/4” & 3/8” 3/4” & 3/8” 3/4” & 3/8”

Quantity 3 3 3 5 5 5 5 5Cross Beams C-5 C-5 C-6 C-6 C-6 C-6 C-6 C-6Cutting EdgesDrag Cutting Edge - AR400 Steel

5/8” x 6” 5/8” x 6” 5/8” x 6” 5/8” x 6” 5/8” x 6” 5/8” x 6” 5/8” x 6” 5/8” x 6”

Push Edge - Reversible Reinforced Rubber

~1” x 12”3 sections








Drag Shoe- AR400 Steel 1-1/8” x 6” 1-1/8” x 6” 1-1/8” x 6” 1-1/8” x 6” 1-1/8” x 6” 1-1/8” x 6” 1-1/8” x 6” 1-1/8” x 6”

Ski-AR400 Steel 3/4” x 4” 3/4” x 4” 3/4” x 4” 3/4” x 4” 3/4” x 4” 3/4” x 4” 3/4” x 4” 3/4” x 4”Shipping Weight +/- 795 lbs. 925 lbs. 1235 lbs. 1500 lbs. 1650 lbs. 2400 lbs. 2600 lbs. 3000 lbs.

Recessed bolt heads on shoes and skis protect bolt heads from wear and allows the plow to clean right up to the curb.

Optional extended ski aids operator in maintaining level plowing position.

Sectional reinforced rubber edges enable easy, cost effective replacement, and offer cleaner plowing of uneven surfaces.

Detachable floating mount allows plow position to adapt to ground contours.

VERSATACH3-IN-1 PLOW

844.BLU.PLOW(844.258.7569)


Imagine the Convenience and Savings of Three Plows in One!

844-BLU-PLOW www.danielsplows.com

Standard Plow Features

VersaTach Plow Specifications

Leading edges of wings are curved •and reinforced with an angled shoe for safety when approaching curbs.

Hydroturn the VersaTach Plow 35 •degrees left and right in any position.

Double-acting Angle Cylinders with 35 •degree maximum plow angling

Double-acting Wing Cylinders with 90 •degree maximum wing rotation

Hydraulic cylinder rods are black nitride •treated for 5x corrosion resistance and extreme durability.

Hydraulic Sequencing Manifold with •plow angle relief built-in

Preset Pressures on manifold valves•

Electric three position switch for angling •and independent wing pivot control

Electricalquickdisconnectfittingsto•manifold solenoids

Full Moldboard Trip•

Drive straight on a trailer to easily cover •multiple sites

Model Number VT12Plow Width *In Straight Postion 12.5’Plow Outside Width *In Box Postion 8’Center Plow Width 6.5’Each Wing (when straight, independently pivoting wings adjustable from 1 degree to 90 degrees)

3’

Inside Box Width 6’Width When Hydroturned *In Straight Postion 10’Moldboard Height 27”Moldboard Material 11 GaugeReinforcement Material 1/4” Min.Tripping Points 5Trip Springs 4Weight (lbs.) 1500Wear Edge 3/4” x 8”Minimum Loader Size (lbs.) 6,000

SAY YES TO THE VERSATACH!

Flick of a switch from inside the 1. cab!

Full hydraulic plow transforms 2. from a Straight Blade to a Box Plow and any shape in between

Each wing controlled separately3.

Entire plow hydroturns 35 4. degrees in either direction in all positions

Offers an unlimited combination 5. of shapes that best match snow and surface conditions

SAY NO TO INCONVENIENCE

NO more returning to the shop •to swap out plows

NO more trying to make a •Straight Blade do the work of a Box Plow

NO more loss of •maneuverability when pushing as a box

The VersaTach Plow utilizes the hydraulics from your machine’s 3rd valve. By connecting the 3rd valve lines to the VersaTach, the hydraulic manifold allows the 3-in-1 Plow to angle left and right 35 degrees and pivot the winds to the degree needed.

Relief is built into the hydraulic manifold to relieve pressure to the VersaTach Plow as it angles when an obstruction is met. Electric switch is supplied with the VersaTach Plow with three positions to control the angling of the Plow and each Wing at any degree independently.

plows - parts for trucks

Documents