polymer flooding - cairo university...the advantages of polymer flooding are two-fold: 1. a...
TRANSCRIPT
![Page 1: POLYMER FLOODING - Cairo University...The advantages of polymer flooding are two-fold: 1. a reduction in the quantity of water required to reduce the oil saturation to its residual](https://reader033.vdocument.in/reader033/viewer/2022042709/5f53e20e1ce047227662a2dc/html5/thumbnails/1.jpg)
12/26/2017 1
POLYMER FLOODING
Dr. Helmy SayyouhPetroleum EngineeringCairo University
![Page 2: POLYMER FLOODING - Cairo University...The advantages of polymer flooding are two-fold: 1. a reduction in the quantity of water required to reduce the oil saturation to its residual](https://reader033.vdocument.in/reader033/viewer/2022042709/5f53e20e1ce047227662a2dc/html5/thumbnails/2.jpg)
12/26/2017 Dr.Helmy Sayyouh 2
You will learn
1. Polymer flood are ideally suited for reservoirs where normal waterfloods fail due to high heterogeneity or high oil-water mobility ratio.
2. Polymers are also used in gas injection and waterflood projects for treating conformance problems.
3. Polymers are also used in many EOR projects to providemobility control behind the injected chemical slug.
![Page 3: POLYMER FLOODING - Cairo University...The advantages of polymer flooding are two-fold: 1. a reduction in the quantity of water required to reduce the oil saturation to its residual](https://reader033.vdocument.in/reader033/viewer/2022042709/5f53e20e1ce047227662a2dc/html5/thumbnails/3.jpg)
12/26/2017 Dr.Helmy Sayyouh 3
4. Polymers are subject to mechanical breakage, shear degradation, temperature sensitivity, and bacterial decay.
5. Selection of right polymer for right application is very important.
6. Some polymer solutions exhibit rate-sensitive behavior.
![Page 4: POLYMER FLOODING - Cairo University...The advantages of polymer flooding are two-fold: 1. a reduction in the quantity of water required to reduce the oil saturation to its residual](https://reader033.vdocument.in/reader033/viewer/2022042709/5f53e20e1ce047227662a2dc/html5/thumbnails/4.jpg)
12/26/2017 Dr.Helmy Sayyouh 4
7. Some polymers exhibit increased effective viscosity while flowing in a reservoir.
8. Adsorption of polymer by rock is a major design consideration.
![Page 5: POLYMER FLOODING - Cairo University...The advantages of polymer flooding are two-fold: 1. a reduction in the quantity of water required to reduce the oil saturation to its residual](https://reader033.vdocument.in/reader033/viewer/2022042709/5f53e20e1ce047227662a2dc/html5/thumbnails/5.jpg)
12/26/2017 Dr.Helmy Sayyouh 5
Introduction
Non-thermal oil recovery methodscould be considered for moderately viscous oils (50-200cp), thin formation (less than 9 m), low permeability's (less than 1 Darcy) and large depths (greater than 900m).
![Page 6: POLYMER FLOODING - Cairo University...The advantages of polymer flooding are two-fold: 1. a reduction in the quantity of water required to reduce the oil saturation to its residual](https://reader033.vdocument.in/reader033/viewer/2022042709/5f53e20e1ce047227662a2dc/html5/thumbnails/6.jpg)
12/26/2017 Dr.Helmy Sayyouh 6
Non-thermal methods serve to:
-reduce the viscosity of the oil,
-increase the viscosity of the displacing fluid, or
-reduce the interfacial tension.
![Page 7: POLYMER FLOODING - Cairo University...The advantages of polymer flooding are two-fold: 1. a reduction in the quantity of water required to reduce the oil saturation to its residual](https://reader033.vdocument.in/reader033/viewer/2022042709/5f53e20e1ce047227662a2dc/html5/thumbnails/7.jpg)
12/26/2017 Dr.Helmy Sayyouh 7
Polymer Injection
–In this process, a water-soluble polymer is used to decrease the mobility ratio of water flooded by increasing the drive water viscosity, and primarily improve the volumetric sweep efficiency.
–It is applicable in the less than 10 to 150 cp viscosity range.
![Page 8: POLYMER FLOODING - Cairo University...The advantages of polymer flooding are two-fold: 1. a reduction in the quantity of water required to reduce the oil saturation to its residual](https://reader033.vdocument.in/reader033/viewer/2022042709/5f53e20e1ce047227662a2dc/html5/thumbnails/8.jpg)
12/26/2017 Dr.Helmy Sayyouh 8
• A polymer flooding is suited for reservoirs where normal waterfloods fail due to one of the two reasons:High Heterogeneity and High oil -water mobility ratio.
• Polymer floods mainly target oil in areas of the reservoir that have not been contacted efficiently.
![Page 9: POLYMER FLOODING - Cairo University...The advantages of polymer flooding are two-fold: 1. a reduction in the quantity of water required to reduce the oil saturation to its residual](https://reader033.vdocument.in/reader033/viewer/2022042709/5f53e20e1ce047227662a2dc/html5/thumbnails/9.jpg)
12/26/2017 Dr.Helmy Sayyouh 9
• Polymers are also used in many other EOR processes - such as surfactant and micellar floods - to provide mobility control at the chemical slug - chase water contact.
• In addition, polymers are also employed for treating conformance problems.
![Page 10: POLYMER FLOODING - Cairo University...The advantages of polymer flooding are two-fold: 1. a reduction in the quantity of water required to reduce the oil saturation to its residual](https://reader033.vdocument.in/reader033/viewer/2022042709/5f53e20e1ce047227662a2dc/html5/thumbnails/10.jpg)
12/26/2017 Dr.Helmy Sayyouh 10
Polymers are long thread-like molecules that are flexible and resilient. When added to
water in a small amount, they have a number of positive effects:
1. Increase apparent viscosity of waterand thereby lower oil-water mobility ratio.
2. Lower mobility ratio results in improving displacement efficiency as well as vertical and areal sweep efficiencies
![Page 11: POLYMER FLOODING - Cairo University...The advantages of polymer flooding are two-fold: 1. a reduction in the quantity of water required to reduce the oil saturation to its residual](https://reader033.vdocument.in/reader033/viewer/2022042709/5f53e20e1ce047227662a2dc/html5/thumbnails/11.jpg)
12/26/2017 Dr.Helmy Sayyouh 11
3.Selectively lower permeability to water without impacting permeability to oil.
4.Improve injectivity and productivity profiles.
![Page 12: POLYMER FLOODING - Cairo University...The advantages of polymer flooding are two-fold: 1. a reduction in the quantity of water required to reduce the oil saturation to its residual](https://reader033.vdocument.in/reader033/viewer/2022042709/5f53e20e1ce047227662a2dc/html5/thumbnails/12.jpg)
12/26/2017 Dr.Helmy Sayyouh 12
Polymers are quite expensive.
Continuous injection is cost prohibitive.
Only a small volume of polymer slug (25 to 40% PV) is injected which is then pushed ahead into the reservoir with plain water.
![Page 13: POLYMER FLOODING - Cairo University...The advantages of polymer flooding are two-fold: 1. a reduction in the quantity of water required to reduce the oil saturation to its residual](https://reader033.vdocument.in/reader033/viewer/2022042709/5f53e20e1ce047227662a2dc/html5/thumbnails/13.jpg)
12/26/2017 Dr.Helmy Sayyouh 13
• Polymer have been used in oil production in three modes:
• As near-well treatments to improve the performance of water injectors or watered out producers by blocking off high conductivity zones.
![Page 14: POLYMER FLOODING - Cairo University...The advantages of polymer flooding are two-fold: 1. a reduction in the quantity of water required to reduce the oil saturation to its residual](https://reader033.vdocument.in/reader033/viewer/2022042709/5f53e20e1ce047227662a2dc/html5/thumbnails/14.jpg)
12/26/2017 Dr.Helmy Sayyouh 14
• As agents that may be cross-linked in situ to plug high conductivity zones at depth in the reservoir.
• As agents to lower water mobility or water-oil mobility ratio.
![Page 15: POLYMER FLOODING - Cairo University...The advantages of polymer flooding are two-fold: 1. a reduction in the quantity of water required to reduce the oil saturation to its residual](https://reader033.vdocument.in/reader033/viewer/2022042709/5f53e20e1ce047227662a2dc/html5/thumbnails/15.jpg)
12/26/2017 Dr.Helmy Sayyouh 15
• Laboratory and simulation studies showed that the oil recovery is generally higher than water flood oil recovery, perhaps 1 to 5 incremental.
• Polymer flooding was reported to be successful in Huntington Beach, California and in Taber South, Canada.
• This process is not cost-effective for heavy oil.
![Page 16: POLYMER FLOODING - Cairo University...The advantages of polymer flooding are two-fold: 1. a reduction in the quantity of water required to reduce the oil saturation to its residual](https://reader033.vdocument.in/reader033/viewer/2022042709/5f53e20e1ce047227662a2dc/html5/thumbnails/16.jpg)
12/26/2017 Dr.Helmy Sayyouh 16
The advantages of polymer flooding are two-fold:
1. a reduction in the quantity of waterrequired to reduce the oil saturation to its residual value in the swept portion of the reservoir.
2. an increase in the areal and vertical coverage in the reservoir due to a reduced water flood mobility ratio.
![Page 17: POLYMER FLOODING - Cairo University...The advantages of polymer flooding are two-fold: 1. a reduction in the quantity of water required to reduce the oil saturation to its residual](https://reader033.vdocument.in/reader033/viewer/2022042709/5f53e20e1ce047227662a2dc/html5/thumbnails/17.jpg)
12/26/2017 Dr.Helmy Sayyouh 17
What is a Polymer?
• Polymer is a chemical that is composed of a number of individual molecules that are attached in some manner.
• These units are usually associated in a pattern that repeats itself throughout the length of each polymer repeating units and are called MONOMERS.
![Page 18: POLYMER FLOODING - Cairo University...The advantages of polymer flooding are two-fold: 1. a reduction in the quantity of water required to reduce the oil saturation to its residual](https://reader033.vdocument.in/reader033/viewer/2022042709/5f53e20e1ce047227662a2dc/html5/thumbnails/18.jpg)
12/26/2017 Dr.Helmy Sayyouh 18
• Example: Polyacrylamide (PAM)
• CH2 – CH – CH2 – CH – CH2 - CH –• l l l• C = O C = O C = O• l l l• NH2 NH2 NH2
![Page 19: POLYMER FLOODING - Cairo University...The advantages of polymer flooding are two-fold: 1. a reduction in the quantity of water required to reduce the oil saturation to its residual](https://reader033.vdocument.in/reader033/viewer/2022042709/5f53e20e1ce047227662a2dc/html5/thumbnails/19.jpg)
12/26/2017 Dr.Helmy Sayyouh 19
Polyacrylamides (PAM)
The polymer straight chain is made up of many acrylamide monomer molecules. Hence, its molecular weight can be tailor made to any desired range (in general from 1 to 10 million ).
The molecule is very long and thin. It is therefore subject to mechanical breakage and shear degradation.
The molecule contracts as salt concentrationincreases. The presence of divalent ions (calcium and magnesium) is very detrimental.
![Page 20: POLYMER FLOODING - Cairo University...The advantages of polymer flooding are two-fold: 1. a reduction in the quantity of water required to reduce the oil saturation to its residual](https://reader033.vdocument.in/reader033/viewer/2022042709/5f53e20e1ce047227662a2dc/html5/thumbnails/20.jpg)
12/26/2017 Dr.Helmy Sayyouh 20
Polysaccharrides (PS)
• It is a bioplymer with average molecularweight of 3-5 million.
• The ring structure provides rigidity and is therefore resistant, to mechanical degradation and tolerant to salinity.
• It is highly susceptible to bacterial action and can create formation plugging.
![Page 21: POLYMER FLOODING - Cairo University...The advantages of polymer flooding are two-fold: 1. a reduction in the quantity of water required to reduce the oil saturation to its residual](https://reader033.vdocument.in/reader033/viewer/2022042709/5f53e20e1ce047227662a2dc/html5/thumbnails/21.jpg)
12/26/2017 Dr.Helmy Sayyouh 21
Mobility Ratio Concept
• The mobility ratio is defined as the mobility of the displacing phase to the mobility of the displaced phase.
• The water-oil mobility ratio can be written as:
M = λw / λo = Krw μo / Kro μw
![Page 22: POLYMER FLOODING - Cairo University...The advantages of polymer flooding are two-fold: 1. a reduction in the quantity of water required to reduce the oil saturation to its residual](https://reader033.vdocument.in/reader033/viewer/2022042709/5f53e20e1ce047227662a2dc/html5/thumbnails/22.jpg)
12/26/2017 Dr.Helmy Sayyouh 22
• The role of water-soluble polymers is to increase the water viscosity and also to reduce the permeability of the rock to water, in other words, to reduce the water-oil mobility ratio close to unity or less.
![Page 23: POLYMER FLOODING - Cairo University...The advantages of polymer flooding are two-fold: 1. a reduction in the quantity of water required to reduce the oil saturation to its residual](https://reader033.vdocument.in/reader033/viewer/2022042709/5f53e20e1ce047227662a2dc/html5/thumbnails/23.jpg)
12/26/2017 Dr.Helmy Sayyouh 23
• After water breakthrough into the producers, the flow of the two phases in the swept area of the reservoir is controlled by the fractional flow equation:
• fw = 1 / ( 1 + (Ko/ μo) (Kw/μw))
• and fo = 1 - fw
![Page 24: POLYMER FLOODING - Cairo University...The advantages of polymer flooding are two-fold: 1. a reduction in the quantity of water required to reduce the oil saturation to its residual](https://reader033.vdocument.in/reader033/viewer/2022042709/5f53e20e1ce047227662a2dc/html5/thumbnails/24.jpg)
12/26/2017 Dr.Helmy Sayyouh 24
Method Description
• In polymer flooding, a slug of polymer solution is injected into the reservoir with a prior injection of a low-salinity brine (fresh water) slug.
• The polymer slug is followed by another fresh water slug and by continuous water injection.
![Page 25: POLYMER FLOODING - Cairo University...The advantages of polymer flooding are two-fold: 1. a reduction in the quantity of water required to reduce the oil saturation to its residual](https://reader033.vdocument.in/reader033/viewer/2022042709/5f53e20e1ce047227662a2dc/html5/thumbnails/25.jpg)
12/26/2017 Dr.Helmy Sayyouh 25
Polymer flooding improves oil recovery over water flooding by increasing the reservoir volume contacted.
• It is successful when applied in the early stages of a water flood process.
• Reservoirs with high permeability variations, the risk factor is high.
![Page 26: POLYMER FLOODING - Cairo University...The advantages of polymer flooding are two-fold: 1. a reduction in the quantity of water required to reduce the oil saturation to its residual](https://reader033.vdocument.in/reader033/viewer/2022042709/5f53e20e1ce047227662a2dc/html5/thumbnails/26.jpg)
12/26/2017 Dr.Helmy Sayyouh 26
Polymer Types
• There are two principle types of polymers being used in field applications:
![Page 27: POLYMER FLOODING - Cairo University...The advantages of polymer flooding are two-fold: 1. a reduction in the quantity of water required to reduce the oil saturation to its residual](https://reader033.vdocument.in/reader033/viewer/2022042709/5f53e20e1ce047227662a2dc/html5/thumbnails/27.jpg)
12/26/2017 Dr.Helmy Sayyouh 27
• Polyacrylamides:
• Is obtained by the polymerization of the acrylamide monomer.
• It has a molecular weight higher than 3 million and a linear chain molecular structure.
• It is sensitive to salt, less expensive and providing higher residual resistance to drive water injection.
![Page 28: POLYMER FLOODING - Cairo University...The advantages of polymer flooding are two-fold: 1. a reduction in the quantity of water required to reduce the oil saturation to its residual](https://reader033.vdocument.in/reader033/viewer/2022042709/5f53e20e1ce047227662a2dc/html5/thumbnails/28.jpg)
12/26/2017 Dr.Helmy Sayyouh 28
• Polysaccharides:
• Is obtained from sugar in a fermentation process caused by the bacterium Xanthomonas campestris.
• It is not affected by salinity, and shear effects can be tolerated.
• This biopolymer is expensive; its stability degrades at temperatures above 200ºF, and is not retained on rock surfaces.
![Page 29: POLYMER FLOODING - Cairo University...The advantages of polymer flooding are two-fold: 1. a reduction in the quantity of water required to reduce the oil saturation to its residual](https://reader033.vdocument.in/reader033/viewer/2022042709/5f53e20e1ce047227662a2dc/html5/thumbnails/29.jpg)
12/26/2017 Dr.Helmy Sayyouh 29
![Page 30: POLYMER FLOODING - Cairo University...The advantages of polymer flooding are two-fold: 1. a reduction in the quantity of water required to reduce the oil saturation to its residual](https://reader033.vdocument.in/reader033/viewer/2022042709/5f53e20e1ce047227662a2dc/html5/thumbnails/30.jpg)
12/26/2017 Dr.Helmy Sayyouh 30
![Page 31: POLYMER FLOODING - Cairo University...The advantages of polymer flooding are two-fold: 1. a reduction in the quantity of water required to reduce the oil saturation to its residual](https://reader033.vdocument.in/reader033/viewer/2022042709/5f53e20e1ce047227662a2dc/html5/thumbnails/31.jpg)
12/26/2017 Dr.Helmy Sayyouh 31
Properties of Polymer Solutions
• Rheology:
• Both types of polymer solutions give non-Newtonian flow characteristics.
• The viscosity of Polymer solutions decrease with increasing temperature.
![Page 32: POLYMER FLOODING - Cairo University...The advantages of polymer flooding are two-fold: 1. a reduction in the quantity of water required to reduce the oil saturation to its residual](https://reader033.vdocument.in/reader033/viewer/2022042709/5f53e20e1ce047227662a2dc/html5/thumbnails/32.jpg)
12/26/2017 Dr.Helmy Sayyouh 32
Stability:
• Mechanical Strength• Bio-polymers are shear stable, but PAM
can be segregated by mechanical shear.
• Thermal Stability• Many laboratory tests have not shown
long-term temperature stability much higher than 259F.
![Page 33: POLYMER FLOODING - Cairo University...The advantages of polymer flooding are two-fold: 1. a reduction in the quantity of water required to reduce the oil saturation to its residual](https://reader033.vdocument.in/reader033/viewer/2022042709/5f53e20e1ce047227662a2dc/html5/thumbnails/33.jpg)
12/26/2017 Dr.Helmy Sayyouh 33
• Bacteriological Stability• Bactericides are used in treating oil field
waters.
• Chemical Stability• The viscosity of polymer solutions is
sensitive to salts.
• Clays increase polymer adsorption.
![Page 34: POLYMER FLOODING - Cairo University...The advantages of polymer flooding are two-fold: 1. a reduction in the quantity of water required to reduce the oil saturation to its residual](https://reader033.vdocument.in/reader033/viewer/2022042709/5f53e20e1ce047227662a2dc/html5/thumbnails/34.jpg)
12/26/2017 Dr.Helmy Sayyouh 34
Resistance Factor
• The measure of the mobility reduction is known as the resistance factor:
• R = λw/ λp = Krw μp / Krp μw = Mw-o / Mp-o
• Polymers with high resistance factors can be used in permeability modification.
![Page 35: POLYMER FLOODING - Cairo University...The advantages of polymer flooding are two-fold: 1. a reduction in the quantity of water required to reduce the oil saturation to its residual](https://reader033.vdocument.in/reader033/viewer/2022042709/5f53e20e1ce047227662a2dc/html5/thumbnails/35.jpg)
12/26/2017 Dr.Helmy Sayyouh 35
![Page 36: POLYMER FLOODING - Cairo University...The advantages of polymer flooding are two-fold: 1. a reduction in the quantity of water required to reduce the oil saturation to its residual](https://reader033.vdocument.in/reader033/viewer/2022042709/5f53e20e1ce047227662a2dc/html5/thumbnails/36.jpg)
12/26/2017 Dr.Helmy Sayyouh 36
Residual Resistance Factor
• The measure of the reduction of rock's permeability to water after polymer flow is known as residual resistance factor:
• Rr = ( Krw /μw) before polymer flow / ( Krw /μw) after polymer flow
![Page 37: POLYMER FLOODING - Cairo University...The advantages of polymer flooding are two-fold: 1. a reduction in the quantity of water required to reduce the oil saturation to its residual](https://reader033.vdocument.in/reader033/viewer/2022042709/5f53e20e1ce047227662a2dc/html5/thumbnails/37.jpg)
12/26/2017 Dr.Helmy Sayyouh 37
Field Projects
ParameterNo. of Projects Mean
•• Depth, ft 87 4005• T, ºF 88 117• Permeability, md 80 453• μo , cp 82 21.5• Polymer ppm 48 279• Recovery, %OOIP 20 3.85
![Page 38: POLYMER FLOODING - Cairo University...The advantages of polymer flooding are two-fold: 1. a reduction in the quantity of water required to reduce the oil saturation to its residual](https://reader033.vdocument.in/reader033/viewer/2022042709/5f53e20e1ce047227662a2dc/html5/thumbnails/38.jpg)
12/26/2017 Dr.Helmy Sayyouh 38
![Page 39: POLYMER FLOODING - Cairo University...The advantages of polymer flooding are two-fold: 1. a reduction in the quantity of water required to reduce the oil saturation to its residual](https://reader033.vdocument.in/reader033/viewer/2022042709/5f53e20e1ce047227662a2dc/html5/thumbnails/39.jpg)
12/26/2017 Dr.Helmy Sayyouh 39
![Page 40: POLYMER FLOODING - Cairo University...The advantages of polymer flooding are two-fold: 1. a reduction in the quantity of water required to reduce the oil saturation to its residual](https://reader033.vdocument.in/reader033/viewer/2022042709/5f53e20e1ce047227662a2dc/html5/thumbnails/40.jpg)
12/26/2017 Dr.Helmy Sayyouh 40
![Page 41: POLYMER FLOODING - Cairo University...The advantages of polymer flooding are two-fold: 1. a reduction in the quantity of water required to reduce the oil saturation to its residual](https://reader033.vdocument.in/reader033/viewer/2022042709/5f53e20e1ce047227662a2dc/html5/thumbnails/41.jpg)
12/26/2017 Dr.Helmy Sayyouh 41
![Page 42: POLYMER FLOODING - Cairo University...The advantages of polymer flooding are two-fold: 1. a reduction in the quantity of water required to reduce the oil saturation to its residual](https://reader033.vdocument.in/reader033/viewer/2022042709/5f53e20e1ce047227662a2dc/html5/thumbnails/42.jpg)
12/26/2017 Dr.Helmy Sayyouh 42
• The original permeability of the core, having been reduced by adsorption on the rock surface and by mechanical entrapment of polymer molecules, cannot be recovered.
![Page 43: POLYMER FLOODING - Cairo University...The advantages of polymer flooding are two-fold: 1. a reduction in the quantity of water required to reduce the oil saturation to its residual](https://reader033.vdocument.in/reader033/viewer/2022042709/5f53e20e1ce047227662a2dc/html5/thumbnails/43.jpg)
12/26/2017 Dr.Helmy Sayyouh 43
Guidelines for Polymer Application
• Reservoir characteristics
• Depth: a critical factor only when related to reservoir temperature.
• Temperature: less than 200ºF assure a stable polymer solution.
• Pressure: is not critical if it permits the injection pressure to be less than the formation parting pressure.
![Page 44: POLYMER FLOODING - Cairo University...The advantages of polymer flooding are two-fold: 1. a reduction in the quantity of water required to reduce the oil saturation to its residual](https://reader033.vdocument.in/reader033/viewer/2022042709/5f53e20e1ce047227662a2dc/html5/thumbnails/44.jpg)
12/26/2017 Dr.Helmy Sayyouh 44
• Porosity: must be medium to high (higher than 18%).
• Permeability: good between 50 and to 250 md.
![Page 45: POLYMER FLOODING - Cairo University...The advantages of polymer flooding are two-fold: 1. a reduction in the quantity of water required to reduce the oil saturation to its residual](https://reader033.vdocument.in/reader033/viewer/2022042709/5f53e20e1ce047227662a2dc/html5/thumbnails/45.jpg)
12/26/2017 Dr.Helmy Sayyouh 45
Fluid Characteristic
• Oil viscosity: up to 200 cp.
• Oil saturation: high
![Page 46: POLYMER FLOODING - Cairo University...The advantages of polymer flooding are two-fold: 1. a reduction in the quantity of water required to reduce the oil saturation to its residual](https://reader033.vdocument.in/reader033/viewer/2022042709/5f53e20e1ce047227662a2dc/html5/thumbnails/46.jpg)
12/26/2017 Dr.Helmy Sayyouh 46
Guidelines for Reservoir Selection
1. Vertical and areal heterogeneity is the primary cause for low recovery under the existing waterflood.
2. Reservoir is not compartmentalized. There are no major faults, fractures, high permeability thief zones, or zonal discontinuities.
3. Rock does not contain excessive clays and minerals
![Page 47: POLYMER FLOODING - Cairo University...The advantages of polymer flooding are two-fold: 1. a reduction in the quantity of water required to reduce the oil saturation to its residual](https://reader033.vdocument.in/reader033/viewer/2022042709/5f53e20e1ce047227662a2dc/html5/thumbnails/47.jpg)
12/26/2017 Dr.Helmy Sayyouh 47
4. Water salinity in the reservoir is not high. Also, clean fresh water source is available for preparation of polymer solution.
5. The oil recovery target should be highto afford expenses associated with injection of large volumes of polymer solution.
6. Reservoir temperature should be less than 2500 - 3000 F. New thermally stable polymers are being developed but their costs are high.
![Page 48: POLYMER FLOODING - Cairo University...The advantages of polymer flooding are two-fold: 1. a reduction in the quantity of water required to reduce the oil saturation to its residual](https://reader033.vdocument.in/reader033/viewer/2022042709/5f53e20e1ce047227662a2dc/html5/thumbnails/48.jpg)
12/26/2017 Dr.Helmy Sayyouh 48
7. The crude oil viscosity is such that the effective mobility ratio is in the target range -- 2 to 20.
8. Reservoir is liquid filled. Otherwise, ,substantial quantities of polymer solution may be lost to filling in the void pore space, inadvertent movement into the gas cap, or displacement of oil outside the drainage area of the well.
![Page 49: POLYMER FLOODING - Cairo University...The advantages of polymer flooding are two-fold: 1. a reduction in the quantity of water required to reduce the oil saturation to its residual](https://reader033.vdocument.in/reader033/viewer/2022042709/5f53e20e1ce047227662a2dc/html5/thumbnails/49.jpg)
12/26/2017 Dr.Helmy Sayyouh 49
Designing a Polymer Flood Program
• Laboratory flow tests should be contacted to duplicate the polymer flood program under the reservoir P&T conditions.
• These tests in preserved or wettability-restored cores would provide information on polymer concentration effect on effective viscosity, polymer injectivity, chase water injectivity, adsorption loss, retention, reduction in residual oil saturation, polymer slug size, oil recovery, etc.
![Page 50: POLYMER FLOODING - Cairo University...The advantages of polymer flooding are two-fold: 1. a reduction in the quantity of water required to reduce the oil saturation to its residual](https://reader033.vdocument.in/reader033/viewer/2022042709/5f53e20e1ce047227662a2dc/html5/thumbnails/50.jpg)
12/26/2017 Dr.Helmy Sayyouh 50
• Using the conventional methods for predicting watertlood response can also make estimate of polymer flood response.
• It is done on the assumption that polymer water would be used throughout. Hence, the predicted results are often optimistic.
![Page 51: POLYMER FLOODING - Cairo University...The advantages of polymer flooding are two-fold: 1. a reduction in the quantity of water required to reduce the oil saturation to its residual](https://reader033.vdocument.in/reader033/viewer/2022042709/5f53e20e1ce047227662a2dc/html5/thumbnails/51.jpg)
12/26/2017 Dr.Helmy Sayyouh 51
POLYMER FLOODING
What have we learned to-date?
1.The international projects - China, Germany, France, Austria Oman, Canada - have proven successful (both technically and economically) in recovering incremental oil over waterfloods.
Incremental Oil Recovery = 6 to 52% OOIP.
![Page 52: POLYMER FLOODING - Cairo University...The advantages of polymer flooding are two-fold: 1. a reduction in the quantity of water required to reduce the oil saturation to its residual](https://reader033.vdocument.in/reader033/viewer/2022042709/5f53e20e1ce047227662a2dc/html5/thumbnails/52.jpg)
12/26/2017 Dr.Helmy Sayyouh 52
2. The USA projects (128) have been only marginally effective in recovering incremental oil over waterfloods.
• Avg. Incremental Oil Recovery = 4.9% OOIP.
• The polymer quantity (PV x PPM) used in the successful international floods exceeded the USA floods by factor of 3 to 16.
![Page 53: POLYMER FLOODING - Cairo University...The advantages of polymer flooding are two-fold: 1. a reduction in the quantity of water required to reduce the oil saturation to its residual](https://reader033.vdocument.in/reader033/viewer/2022042709/5f53e20e1ce047227662a2dc/html5/thumbnails/53.jpg)
12/26/2017 Dr.Helmy Sayyouh 53
3. Projects cover a wide range of reservoir properties
• Reservoir Temperature < 1500 F• High Perm, Porosity Sandstones• Salinity. Domain - - 5 to 200K PPM Polymers -
-• HPAM, Xanthan • Polymer Quantity - - 46 to 700 PV x PPM • Oil Saturation at Start of Flood - - 50 to 70% • Oil Viscosity - - 7 to 80 cp• Viscosity of Injected Polymer - - 10 to 20 cp
![Page 54: POLYMER FLOODING - Cairo University...The advantages of polymer flooding are two-fold: 1. a reduction in the quantity of water required to reduce the oil saturation to its residual](https://reader033.vdocument.in/reader033/viewer/2022042709/5f53e20e1ce047227662a2dc/html5/thumbnails/54.jpg)
12/26/2017 Dr.Helmy Sayyouh 54
4. Many reasons are cited for the success of these projects:
• Improved areal and vertical sweep efficiencies
• Improved displacement efficiency • Acceleration of oil production • Shortening of project life • Re-pressurization of reservoir
![Page 55: POLYMER FLOODING - Cairo University...The advantages of polymer flooding are two-fold: 1. a reduction in the quantity of water required to reduce the oil saturation to its residual](https://reader033.vdocument.in/reader033/viewer/2022042709/5f53e20e1ce047227662a2dc/html5/thumbnails/55.jpg)
12/26/2017 Dr.Helmy Sayyouh 55
5. The successful projects were matched viscosity floods - -the viscosity of polymer bank at the leading edge was equal or higher than oil viscosity under reservoir conditions.
![Page 56: POLYMER FLOODING - Cairo University...The advantages of polymer flooding are two-fold: 1. a reduction in the quantity of water required to reduce the oil saturation to its residual](https://reader033.vdocument.in/reader033/viewer/2022042709/5f53e20e1ce047227662a2dc/html5/thumbnails/56.jpg)
12/26/2017 Dr.Helmy Sayyouh 56
6. Many successful projects used a polymer concentration taper, thereby minimizing
slug breakdown due to fingering.
7. Detailed laboratory core floods, small-scale field pilots, and simulation modeling
preceded successful floods.