ponyprog now works with several hardware interfaces

8/2/2019 PonyProg Now Works With Several Hardware Interfaces

1/10

PonyProg now works with several hardware interfaces. Choose the one you prefer and try it.

SI Prog (Serial port Interface for PonyProg)

The official PonyProg hardware interface. It works with all devices supported by PonyProg

All schematics in this page are copyrighted by Claudio Lanconelli, you need my permission

before to publish them in your site, magazine or other media.

Some adapters are not available as GIFs. Look at PDF file, please.

Complete schematics are available in Acrobat PDF file format:


2/10

SI-Prog base: connect it to the PC DB9 serial port.

You can connect any of the following adapter card to the 10 pin connector. The interface sinks current

from the PC serial port, so it doesn't need any external power.

AVR microcontroller adapter

AVR 20 pin (AT90S1200, AT90S2313) connect diagram tobase board

AVR 40 pin (AT90S4414, AT90S8515) connect diagram tobase board

AVR 8 pin (AT90S2323, AT90S2343, ATtiny12) connect diagram tobase board
http://www.lancos.com/siprogsch.html#baseboardhttp://www.lancos.com/siprogsch.html#baseboardhttp://www.lancos.com/siprogsch.html#baseboardhttp://www.lancos.com/siprogsch.html#baseboardhttp://www.lancos.com/siprogsch.html#baseboardhttp://www.lancos.com/siprogsch.html#baseboardhttp://www.lancos.com/siprogsch.html#baseboardhttp://www.lancos.com/siprogsch.html#baseboardhttp://www.lancos.com/siprogsch.html#baseboardhttp://www.lancos.com/siprogsch.html#baseboardhttp://www.lancos.com/siprogsch.html#baseboard


3/10

ATmega microcontroller adapter

ATmega103 / ATmega128 connect diagram to base board

Note that this AVR don't use MISO, MOSI pins for SPI programming, instead use PE0, PE1
http://www.lancos.com/siprogsch.html#baseboardhttp://www.lancos.com/siprogsch.html#baseboardhttp://www.lancos.com/siprogsch.html#baseboardhttp://www.lancos.com/siprogsch.html#baseboardhttp://www.lancos.com/siprogsch.html#baseboard


4/10

Atmel core51 microcontroller adapter

AT89S8252/AT89S53 connect diagram tobase board
http://www.lancos.com/siprogsch.html#baseboardhttp://www.lancos.com/siprogsch.html#baseboardhttp://www.lancos.com/siprogsch.html#baseboardhttp://www.lancos.com/siprogsch.html#baseboard


5/10

PIC 12/16 adapter

PIC16F8xx and PIC12C50x connect diagram tobase board
http://www.lancos.com/siprogsch.html#baseboardhttp://www.lancos.com/siprogsch.html#baseboardhttp://www.lancos.com/siprogsch.html#baseboardhttp://www.lancos.com/siprogsch.html#baseboard


6/10

ICBus eeprom adapter

I2C Bus eeprom (24Cxx, SDE2516, ...) connect diagram tobase board

Microwire eeprom adapter

Microwire eeprom (93Cx6) connect diagram tobase board

SPI eeprom adapter

SPI eeprom (25xxx, 95xxx) connect diagram tobase board

SDE2506 eeprom adapter
http://www.lancos.com/siprogsch.html#baseboardhttp://www.lancos.com/siprogsch.html#baseboardhttp://www.lancos.com/siprogsch.html#baseboardhttp://www.lancos.com/siprogsch.html#baseboardhttp://www.lancos.com/siprogsch.html#baseboardhttp://www.lancos.com/siprogsch.html#baseboardhttp://www.lancos.com/siprogsch.html#baseboardhttp://www.lancos.com/siprogsch.html#baseboardhttp://www.lancos.com/siprogsch.html#baseboardhttp://www.lancos.com/siprogsch.html#baseboardhttp://www.lancos.com/siprogsch.html#baseboardhttp://www.lancos.com/siprogsch.html#baseboard


7/10

SDE2506 connect diagram tobase board

NVM3060 eeprom adapter

NVM3060 connect diagram tobase board

MDA2061 MDA2062 eeprom adapter
http://www.lancos.com/siprogsch.html#baseboardhttp://www.lancos.com/siprogsch.html#baseboardhttp://www.lancos.com/siprogsch.html#baseboardhttp://www.lancos.com/siprogsch.html#baseboardhttp://www.lancos.com/siprogsch.html#baseboardhttp://www.lancos.com/siprogsch.html#baseboardhttp://www.lancos.com/e2p/mda-adapter.pnghttp://www.lancos.com/siprogsch.html#baseboardhttp://www.lancos.com/siprogsch.html#baseboard


8/10

Click to enlarge

MDA2062 connect diagram tobase board

VR ISP (STK200/300) parallel port interface

The best way to perform AVR ISP programming. It works even in low voltage systems (3V). To

select it choose "AVR ISP I/O" or "AVR ISP API" from the Options - Setup menu and theparallel checkbox.

You can connect directly to the target system (ISP) through the 10 pin connector, alternatively

you can connect a PonyProg adapter card for AVR, AT89S, SPI eeproms, microwire eeproms

and feed external power to the device."AVR ISP API" on Linux version need the parport, parport_pc and ppdev kernel modules.

On Windows2000/XP you have to select "AVR ISP I/O" and use a standard PC LPT port.

Note that this interface doesn't support ICBus devices, use the SI-Prog or EasyI2CBus interfaceinstead.

The STK200/300 official dongle is provided by Kanda.

Some people suggest me improvements to the original STK200 dongle. For the discussionlookhere

Here are the improved schematics.

AVR ISP with STK200/300 pinout (connect it to STK200/300 eva board)
http://www.lancos.com/e2p/mda-adapter.pnghttp://www.lancos.com/e2p/mda-adapter.pnghttp://www.lancos.com/siprogsch.html#baseboardhttp://www.lancos.com/siprogsch.html#baseboardhttp://www.lancos.com/siprogsch.html#baseboardhttp://www.avrfreaks.net/index.php?name=PNphpBB2&file=viewtopic&t=33265http://www.avrfreaks.net/index.php?name=PNphpBB2&file=viewtopic&t=33265http://www.avrfreaks.net/index.php?name=PNphpBB2&file=viewtopic&t=33265http://www.avrfreaks.net/index.php?name=PNphpBB2&file=viewtopic&t=33265http://www.lancos.com/siprogsch.html#baseboardhttp://www.lancos.com/e2p/mda-adapter.png


9/10

AVR ISP with SI-Prog pinout (connect it toSI-ProgAVR adapter boards)
http://www.lancos.com/siprogsch.htmlhttp://www.lancos.com/siprogsch.htmlhttp://www.lancos.com/siprogsch.htmlhttp://www.lancos.com/siprogsch.html


10/10

ponyprog now works with several hardware interfaces

Documents