300Mbps Inwall Wireless Repeater

Quick Installation Guide

300Mbps InwallWireless Repeater

Quick Installation Guide

Hardware and Operation Mode

LED and Interface

PowerWLANEthernetSystem

Gateway Mode

Access Point Mode

Repeater Mode

AP Mode AP Mode

AP MODE Repeater MODE

Router/Switch

Operation Mode

Gateway

Router/Switch

Installation Steps

Hardware Connection

Setting the Computer

Log in the Web Management

Setting the AP

Test the Wireless Network

Install the AP to the Wall

Note:1. Before Install the AP on the wall, you wouldbetter complete the software setting.2. Before the setting of the AP, you would bettercomplete the design of Topology of networkand IP address the devices.

Hareware Conection

Setting the Repeater through Wireless

Setting the AP using WirelessPlug the Wireless Repeater to the Outlet, and using wireless to connect the repeater (SSID：CQ300, Key:66666666), and then log the 192.168.0.1 to setting the Repeater using the IE Browser.

and then log the 192.168.0.1 to setting the AP using the IE Browser.Plug the Wireless Repeater to the Outlet, and using wires connect to the repeater

Hardware Connection

Inwall Repeater

Inwall Repeater

Setting the Repeater through Wires with RJ45 Cable

Setting the AP using Wires

As belows shows.

Setting the ComputerSetting the AP through Wireless

same network segment as AP,subnet mask 255.255.255.0

the default Passwords is"66666666"CQ300

ZHH

segment as the AP subnet mask 255.255.255.0 As belows shows.

Setting the AP through Wires with RJ45 Cable

1

2 3

WAN/LAN Ethernet Port

Micro USB Port for Power

WPS Button

Power Plug

Log in the Web Managementa.Open your web browser, type 192.168.0.1 in the address bar

b.enter the User name/Passwords: preset as admin/admin, then you can found on the label attached to the router, click OK

Setting the APEnter into the page of WEB software management page, then set Inwall AP as requirement. The default working mode is Access Point.

Choose the “Internet Settings”, that means AP will change to Gataway Mode:

Choose the “Wireless Repeater”, that means AP will change to Repeater Mode:

WAN Setting: Choose Dail Way, PPPoE/Dynamic IP Support.PPPoE need User Name and User Password �ll in, which is provided by ISP, then settingthe Wireless Network, such as SSID and Key of the netowrk. Click the Apply the System will reboot.NOTE: In the mode, the DHCP Server is enable by default, the computer can get the IPaddress from AP.

SSID: Fill in the name of wireless network

IP/Port/MAC/URL Filtering: This feature is turned on, the router will be in accordancewith the �ltering rules are selected for forwarding of data limitations. When the �ltering rules for [refuse], the router will refuse to forward data in accordance with the conditions; when the �ltering rules to [allow], the router will only transmit data in accordance with the conditions

Channel: Setting the Channel of wireless network

Encryption: Choose the AES type, and setting the key of wireless netowrk.

NOTE: In the mode, the DHCP Server is disable by default, you need change the IPAddress to the same subnet with former Router/Switch.

Gateway Mode

AP Mode Advances Setting

Repeater Mode 2. Then input the right password (wireless key) .

2. Click Scan AP , then choose the Wireless Network you want

3. Type the SSID and Key of your wireless network.

Choose the “Wireless Coverage”, that means AP will change to AP Mode: Choose the “Advances Setting”, you can set Firewall and Management function of AP: If the exist wireless access point, routers with WPS Button, very easy to makeour wi� repeater to bridge and extend the exist wi� signal by press WPS button.

1. Push the WPS button of wi� router or ap2. Push the WPS button of wireless repeater3. Done!

NOTE: In the mode, the DHCP Server is disable by default, you need change the IPAddress to the same subnet with former Router/Switch.

Backup: Save the con�guration �le to your computer Restore: Using the saved con�guration �le recovery con�guration Reset Default: Restore the factory default settings, please press this button Reboot: Device will restartRouter, DDNS, QoS, User Logs, Upgrade Firmaware are also supports

Symptoms TreatmentForget the login user name and passwords

Can’t login AP through WEB management

Forget the AP’s SSID and passwords

Mobile Phone canaccess the Internet, butPC can not access

No Power indicator 1. If DC Power, check the local power supplier2. If PoE Power, check the PoE adapter and Internet cable

Restore to factory default

Restore to factory default

Change the Channel of Wi� to 1~11, some PCdo not support the 12, 13 channel

Trouble Shooting Appendix 2Using the WPS Button Appendix 1

1 Pls make sure the PC and AP’s IP Address are in same network segment, can be checked through Ping: PC start--input CMD in Run, then ping 192.168.0.1 2 Login after Restore AP to factory default3 Make sure there isn’t any equipment take IP address of 192.168.0.1 in AP networking4 Check your computer and network cable to avoid any problem, recommend to use unshielded twisted pair 10/100M Ethernet cable.

4 5

6

WAN/LAN Ethernet Port

Micro USB Port for Power

WPS Button

Power Plug