power quality f efficiency - electrahertz · power quality & efficiency generator controllers...

Power quality& efficiency

Generator controllers Lovato F-1 – 2

Automatic transfer controllers Lovato F-3

Battery chargers Lovato F-4

Power capacitors

Lovato F-5Power factor controllers

Electronicon F-6

EM F-7 – 10Power factor racks and systems

Schaffner F-11Delta F-12

Active/ passive harmonic filters

Finder F-13Hager F-14

Occupancy sensors

Finder F-13Modular time switches

F1

F2

F

F-10Above prices do not include VAT. E&OE

Pow

er q

ualit

y &

effi

cien

cy

525V power factor racks and systems

RCSE series power factor rack systemRCSE series power factor racks are designed for direct panel mounting onto vertical supports within floor standing electrical panels

RCSE series rack design incorporates the following:• Sheet metal mounting frame for easy panel mounting (capacitors visible without having to remove rack)• Electronicon heavy duty “gas filled” cylindrical capacitors (with integrated discharge resistors)• Special capacitor switching contactors 400 VAC coil (230V on request)• Three-phase busbar mounted fuse holder with hinged fuse protection cover• Suitably rated HRC fuses for each phase of each capacitor bank• Incorporated busbar, supports and inter-connecting busbar links• Dimensions: From front of switchgear to front plate: 150 mm Behind front mounting plate: 320 mm Between vertical supports: 486 mm

type kvar at: description dimensions (mm) price 525V 400V (H) (W) (D)

RCSE series single step racks (525V capacitors) fuse protection

RCSE01505 15 9 single step capacitor rack system 270 555 470 4580.00RCSE03005 30 18 single step capacitor rack system 270 555 470 6280.00RCSE06005 60 36 single step capacitor rack system 270 555 470 9470.00

RCDE series double-step racks (525V capacitors) separate fuse protection for each bankRCDE03025 2 x 15 2 x 9 double step capacitor rack system 270 555 470 7540.00RCDE06025 2 x 30 2 x 18 double step capacitor rack system 270 555 470 10780.00RCDE12025 2 x 60 2 x 36 double step capacitor rack system 270 555 470 17260.00RCDE04535 15 + 30 9 + 18 double step capacitor rack system 270 555 470 7590.00RCDE09035 30 + 60 18 + 36 double step capacitor rack system 270 555 470 14010.00

Power factor systems (automatic) 525V

For applications with varying capacitor requirements. An automatic reactive controller monitors the network and only switches capacitor banks when required, avoiding potential over or under compensation in a network.FMSE series floor standing systems (165 - 1050 kvar - 525V)Complete ready-to-install system comprising following:• Suitably ventilated floor standing enclosure (thermostatically controlled roof mounted exhaust fan)• Mains isolator, door interlocking (with early make/late break auxiliary contact)• High end reactive controller DCRG 8 (with digital display of all important network parameters)Able to monitor all three phase voltage and currents, providing accurate indication of: - Active, Apparent Power as well as Active, Reactive, Apparent Energy monitoring - Current and Voltage Harmonics analysis (up to 31st harmonic) - Calendar-clock with backup reserve power - Event logging: alarms, setup changes, events ect. (internal memory stores last 250 events) - Internal panel temperature monitoring - Expandable with up to 4 expansion modules for: additional steps, analog I/O’s, RS323, RS485, Ethernet, GPRS/GSM modem communication

type kvar at: steps (kvar) 525V expands dimensions (mm) 525V 400V 15 30 60 to (kvar) (H) (W) (D)

FMSE series floor standing complete power factor systems (525V capacitors)

• Reverse-flow roof mounted exhaust fan (improved cooling and ventilation of the entire panel)• Bottom cable entry (top entry available on request)• RC series racks heavy duty cylindrical capacitors, fusegear and busbars “special” capacitor switching contactors incorporating limiting inductances

FMSE01605 165 99 1 1 2 525 2180 600 630 54320.00FMSE02105 210 126 1 3 570 2180 600 630 61050.00FMSE02505 255 153 1 2 3 525 2180 600 630 68930.00FMSE02805 285 171 1 1 4 525 2180 600 630 75380.00FMSE03305 330 198 1 5 570 2180 600 630 79110.00FMSE03905 390 234 1 6 570 2180 600 630 88980.00FMSE04505 450 270 1 7 570 2180 600 630 97170.00FMSE05705 570 342 1 9 – 2180 600 630 115230.00FMSE06905* 690 414 1 11 1050 2180 1200 630 154900.00FMSE08105* 810 450 1 13 1050 2180 1200 630 172960.00FMSE09305* 930 486 1 15 1050 2180 1200 630 191030.00FMSE10505* 1050 522 1 17 – 2180 1200 630 209090.00

* Made up by combining two panels with one controller operating all capacitor banks

Remote monitoringFor remote monitoring and control of all electrical network parameters (including harmonics), panel internal temperature, alarms, events and all setup parameters. (see page F-5 for all comm. options)

Made in Germany

FMSE...

F-11 Above prices do not include VAT. E&OE

Active / Passive harmonic filters

FN3416-45-33

FN3420-200-480-3

FN3420...

FN3258-16-44

ECOsine Active harmonic filters

Multiple functions: harmonic filtering - reactive power compensation - load balancing Reliability and efficiency are important to business operation. This includes reliable operation of machines, manufacturing systems, and office equipment. Nevertheless, this is frequently not the case and often there is no obvious reason, despite the use of UPS and back-up generators. Unlike passive harmonic filters, these filters can provide harmonic mitigation under any load conditions up to their rated capacity.• Global or selective compensation of harmonic currents up to the 50th order (reduces THID to 1.5% - 3%) • Compensation of displacement power factor• Load balancing• Response time: less than 300 μs • Adapts to changing network topologies instantly• Up to 5 units can be wired in parallel to increase overall system requirements

type rated current phase IP rating power dimensions (mm) price 400V (A) loss (W) (H) (W) (D)

ECOsine three wire active harmonic 380 - 480 VAC ±10% (500 - 690 VAC available on request)

FN3420-50-480-3 50A 3 wire IP20 <1300 615 358 288 203632.00FN3420-120-480-3 120A 3 wire IP20 <2500 972 469 412 297440.00FN3420-200-480-3 200A 3 wire IP54 <5000 2105 808 604 1084512.00FN3420-300-480-3 300A 3 wire IP54 <7500 2105 808 604 1255929.004-wire version available on request for triple harmonic filtering eg. 3rd, 9th, 15th….orders

ECOsine passive harmonic filters

ECOsine FN 3416 represent very compact “economy line” with THID performance of ≤10 % in conjunction with the VSD’s built in DC-link choke. Ideal for non-linear three-phase equipment with 6-pulse front end rectifier circuits. Sufficient to comply with EN61000-3-12 or IEEE-519 and other power quality standards. Schaffner ECOsine filters help to unburden electrical infrastructures from excess loading and heat caused by current harmonics, and therefore support better utilization of electric system capacity. Lower harmonics also reduce the risk of system resonances and potential downtime of sensitive electronic equipment.FN 3416 filters upgrade standard motor drives to “low-harmonic drives” quickly and easily.• THID performance of <10% (5% available on request)• Compact design - Quick installation • Efficient: >98% nominal line voltage and power• Conformity to: UL508, EN61558-2-20, CE (LVD2006 / 95 / EC)

type rated current rated load power (kW) power dimensions (mm) 400V (A) 400V 500V loss (W) (H) (W) (D)

FN3416-45-33 45A 22 30

306 455 280 230 46712.00FN3416-60-34 60A 30 37 408 520 280 248 53524.00FN3416-75-34 75A 37 45 410 520 280 248 62672.00FN3416-110-35 110A 55 75 546 580 280 248 87195.00FN3416-150-40 150A 75 90 784 700 450 385 102084.00Larger sizes up to 200kW available on request

EMC/RFI filters three-phase filters

Electro Magnetic Interference (EMI) unwanted high frequencies which ride on the AC waveform. Many products such as variable frequency drives generate EMI, which may interrupt, obstruct, degrade or limit the effective performance of electronic equipment.• Max. continuous operating voltage: 480/277 VAC• Exceptional attenuation performance from 150kHz to 30Mhz• Excellent saturation resistance up 50 meters cable length• Most compact and slim filter design in its class• Increases the immunity of the equipment being protected• Compliance with class A according to EN 55011

rated typical leakage power dimensions (mm)type current drive current loss (H) (W) (D) 50°C size 400V (W)

FN3258-16-44 16A 7.5kW 33.0 mA 6.1 250 45 70 3374.00FN3258-30-33 30A 15kW 33.0 mA 11.8 270 50 85 3949.00FN3258-42-33 42A 22kW 33.0 mA 15.7 310 50 85 4622.00FN3258-55-34 55A 30kW 33.0 mA 25.9 250 85 90 5567.00FN3258-75-34 75A 37kW 33.0 mA 32.2 270 80 135 7093.00FN3258-100-35 100A 55kW 33.0 mA 34.5 270 90 150 8659.00FN3258-130-35 130A 75kW 33.0 mA 43.1 270 90 150 10285.00FN3258-180-40 180A 90kW 33.0 mA 58.3 380 120 170 13352.00


Made in GermanyAnti-harmonic power factor systems (automatic)

Rack systems incorporating anti-harmonic de-tuned reactorsHRSE series power racks are designed for direct panel mounting onto horizontal rail supports within panels

HRSE series rack design incorporates the following:• Heavy duty sheet metal mounting frame• Electronicon heavy duty “gas filled” cylindrical capacitors (with integrated discharge resistors)• Suitably rated special capacitor switching contactors incorporating limiting resistors• Anti-harmonic de-tuned reactors (for networks with THDU ≤6% and/or THDI ≤40%)• Three-phase busbar mounted fuse holder for each capacitor bank with suitably rated HRC fuse links• Incorporated busbar, supports and inter-connecting busbar links

type kvar at: description dimensions (mm) price 400V 440V (H) (W) (D)

HRSE series power factor rack system with anti-Harmonic Reactors

HRSE series single step anti-harmonic racksHRSE01204 12.5 15 single step capacitor + reactor unit 310 740 538 8680.00HRSE02504 25 30 single step capacitor + reactor unit 310 740 538 11240.00HRSE05004 50 60 single step capacitor + reactor unit 310 740 538 15180.00

HRDE series double-step anti-harmonic racksHRDE05024 2 x 25 2 x 30 double capacitor step + reactor unit 310 740 538 19690.00HRDE10024 2 x 50 2 x 60 double capacitor step + reactor unit 310 740 538 28350.00

HRDE03734 12.5 + 25 15 + 30 double capacitor step + reactor unit 310 740 538 17080.00HRDE07534 25 + 50 30 + 60 double capacitor step + reactor unit 310 740 538 24000.00

FHRE series floor standing power factor systems with anti-harmonic de-tuned reactors

For installations subject to harmonics on sites utilising harmonic generating devices such as:variable speed drives, inverters, UPS systems, battery chargers, LED lighting etc.

Complete ready-to-connect floor standing system comprising:• Suitably ventilated floor standing enclosure with roof mounted exhaust fan• Mains isolator, door interlocking (with early make/late break auxiliary contact)• High end reactive control relay DCRG 8 (with digital display of all important network parameters)• Can be configured to monitor three voltage and current phases, to provide accurate indication of: - Active, Apparent power as well as Active, Reactive, Apparent Energy monitoring - Current and Voltage Harmonics analysis (up to 31st harmonic) - Calendar-clock with backup reserve power - Event logging: alarms, setup, changes, etc. (internal memory stores last 250 events) - Internal panel temperature monitoring• Expandable with up to 4 expansion modules for: - Additional steps, analog I/O’s, RS323, RS485, Ethernet, GPRS/GSM modem communication

type kvar at: steps (kvar) at 400V expands dimensions (mm) 400V 440V 12.5 25 50 to kvar (H) (W) (D)

FHRE series floor standing complete power factor systems (440V capacitors)

• Reverse-flow roof mounted exhaust fan (improved cooling and ventilation of the entire panel)• Bottom cable entry (top entry available on request)• Series HR racks incorporating following: - Heavy duty Electronicon capacitors - Fusegear and busbars per capacitor bank - Anti-harmonic de-tuned reactors (for networks with THDU ≤6% and/or THDI ≤40%)

FHRE11304 113 (120) 136 1 2 1 320 2280 900 600 72140.00FHRE13804 138 (146) 166 1 1 2 346 2280 900 600 76690.00FHRE15004 150 (160) 180 – 2 2 360 2280 900 600 79400.00FHRE17504 175 (200) 210 – 1 3 400 2280 900 600 83900.00FHRE23804 238 (250) 300 1 1 4 350 2280 900 600 105840.00FHRE27504 275 (300) 330 – 1 5 400 2280 900 600 113050.00FHRE33804 338 (360) 420 1 1 6 – 2280 900 600 134990.00FHRE37504 375 (400) 450 – 1 7 – 2280 900 600 142200.00

FHRE43824* 438 (465) 575 1 1 8 765 2350 1800 600 187040.00FHRE47524* 475 (500) 575 – 1 9 775 2350 1800 600 194250.00FHRE57524* 575 (610) 695 – 1 11 775 2350 1800 600 223400.00FHRE67524* 675 (720) 815 – 1 13 775 2350 1800 600 253150.00FHRE77524* 775 (825) 940 – 1 15 – 2350 1800 600 292300.00


Remote monitoringFor remote monitoring and control of all electrical network parameters (including harmonics), panel internal temperature, alarms, events and all setup parameters. (see page F-5 for all comm options)

FHRE...

HRDE...


Pow

er q

ualit

y &

effi

cien

cy

Automatic battery chargers

BCF...

BCG ...

BCE...

Switchmode battery chargers• Switchmode technology• Charging cycle in accordance with DIN 41773 standards• Automatic reset at end of alarm conditions

output output max. power description

dimensions (mm) type

voltage current consumption

(H) (W) (D) price

VA W

BCF series modular automatic switching battery chargers

• Modular DIN rail mounting (aligns with standard MCB’s) or chassis mount• Wide auxiliary supply range 100 - 240 VAC (±10%) 50/60Hz• Protection: - Mains input fuse (non replaceable) - Battery output fuse - Electronic lock in case of short circuit on battery terminals, reverse Battery polarity and battery overload• LED indication of: - Correct output voltage - Reverse battery polarity• Alarm output relay (3A 250 VAC) AC1 duty

BCF025012 12V 2.5A 80 49 auto battery charger 96 90 56 1195.00BCF045012 12V 4.5A 150 70 auto battery charger 96 90 56 1481.00

BCF012524 24V 1.25A 80 39 auto battery charger 96 90 56 1195.00BCF025024 24V 2.5A 150 77 auto battery charger 96 90 56 1481.00

BCG series rail mount switching battery chargers

• High efficiency• Wide auxiliary supply range 110 - 240 VAC (±10%) 50/60Hz• DIN rail or chassis mounting (can be mounted vertically with adaptor)• Boost signal controlled by external contact• Hiccup function for battery recharging when its voltage is lower than 50% rated value• Maximum charging current limiting trimmer 20 - 100% (adjustable from front)• Protection: - Mains input fuse - Electronic lock in case of short circuit on battery terminals, reverse Battery polarity and battery overload• LED indication of: - Power ON - Charging operation I>30% Ic - Overload or short circuit condition - Reverse battery polarity• Alarm output relay (5A 30 VDC) duty

BCG0612 12V 6A 230 97 auto battery charger 150 162 63 2284.00BCG1212 12V 12A 384 190 auto battery charger 150 162 63 4428.00

BCG0524 24V 5A 364 158 auto battery charger 150 213 63 2284.00BCG1024 24V 10A 630 311 auto battery charger 150 213 63 4428.00

Accessories for above BCG battery chargers

BCGX00 vertical side mount adaptor (for space saving) for BCG0612 and BCG0524 77.00

BCE series linear battery chargers

• Linear technology• Auxiliary supply voltage: 220 - 240 VAC (±10%) 50/60Hz• Charging current: 30 - 100% i.e (adjustable)• Protection: - Mains input fuse (except BCE2V524 and BCE0312) - Battery output fuse - Electronic lock in case of short circuit on battery terminals, reverse Battery polarity output overload <0.5 Ue and disconnected battery• LED indication of: - Power ON - Charge I>0.2 Ic - Alarm for protection tripping• Alarm output: Static NPN transistor BCE2V5 and BCE03 - others relay (5A 250 VAC)

BCE0312 12V 3 117 – auto battery charger 93 134 100 3056.00BCE0612 12V 6 222 – auto battery charger 130 192 140 4929.00BCE1212 12V 12 400 – auto battery charger 230 192 140 7264.00

BCE2V524 24V 2.5 166 – auto battery charger 93 134 100 3244.00BCE0524 24V 5 317 – auto battery charger 130 192 140 5306.00BCE1024 24V 10 610 – auto battery charger 230 192 140 8029.00


Automatic transfer switch controllers

ATL600

Automatic transfer switch controllersAutomatic mains failure (AMF) gen-set controllers• Supervision of two or three three-phase power sources• Emergency demand supervision for stand-by generating sets• Tie-breaker management• Automatic non-priority load management• IR programming port on front panel for communication with PC• Event logging• Remote control and supervision• Modbus-RTU, Modbus-ASCII and Modbus-TCP communication protocols

type digital relay description price inputs outputs

ATL600 series 144 x 144 mm panel mounting

- AC power supply- Management of two power sources- Measurement inputs for three phase + neutral voltage values (suitable for 1 and 2 phase lines)- 128 x 80 backlit graphic LCD to view measurements, events and alarms

ATL600 6 7 automatic transfer switch controller for 2 sources 7730.00


As above ATL600 but with following additional features:- Dual power supply (110 - 240 VAC line and 12 - 24 VDC battery supply)- Real time clock RTC- Expandable with rear plug-in expansion modules (see page F-5)

ATL610* 6 7 automatic transfer switch controller for 2 sources 9912.00

* 2 slot to accept plug-in expansion modules EXP1010/1011/1012/1013/1014


As above ATL610 but with following additional features:- Management of 2 energy sources and 1 tie breaker- 6 preconfigured system layouts- Built-in NFC technology for parameter setup via smartphone or tablet- Built-in RS485 communication- Built-in programmable PLC logic- Expandable with rear plug-in expansion modules (see page F-5)



As above ATL800 but with following additional features:- Management of 3 energy power sources and 2 tie breakers- 4 current inputs for the three phases and neutral- 14 preconfigured system layouts- 128 x 112 backlit graphic LCD to view measurements, events and alarms- Expandable with rear plug-in expansion modules (see page F-5)


ATL100 series (econo) automatic transfer controller 54 mm wide

Suitable for monitoring two independent power sources and to manage switching between thetwo sources with single phase control. Combined with two contactors, the controller is ideal forsimple applications which do not require all controls

• Modular DIN43889 housing (3 modules wide 54 mm)• Response thresholds of min and max voltage: 80% and 120% of nominal setting• 2 single phase inputs and outputs L+N• Priority line: L• LED indication: 2 x (green) presence of both input voltages, 1 x presence of output voltage 1 x (red) indicates presence voltage out of limits on inputs

ATL100 2 2 single phase automatic transfer controller 4092.00

ATL900

ATL 100

new


Energy saving devices

18.41

18.51

18.21

18.31

Modular time switchesFinder digital time switches incorporate easy to use NFC (Near Field Communication) for fast, flexible programming of time via a smartphone, can also be performed via the front mounted joystick control

• Versions with 1 or 2 contacts - 16A• 110…230 VAC/DC supply• Internal battery (easily replaceable) for set-up and programming without supply voltage• Wide backlit display for easy programming and visualisation

type time min. reserve contact width in price range setting configuration 17.5 mm

Digital (analog-style) digital time switch

• Easily configurable for daily or weekly programming

125182300000 24hr/7 day 30 min. yes 1 CO 2 1093.00

Digital time switch with programmable pulse output

• Switch ON/OFF override facility• Pulse output from 1 second to 59 minutes• Holiday program

126182300000 7 day 1 sec. yes 1 CO 2 1345.00

Astro time switches (calculates sunrise/sunset according to longitude/latitude coordinates)

• Astro program: calculation of sunrise and sunset times through date, time, location coordinates• Programmable offset from Astronomic times (up to 90 min)

12A182300000 7 day 1 sec. yes 1 CO 2 1457.0012A282300000 7 day 1 sec. yes 2 CO 2 1745.00

PIR movement detectors (IP40)

type switching load description A/VA

Movement detectors (economic version) 120 - 230 VACCompact economical ceiling mount movement detector for internal installations, these sensors detect movement in common areas and operate lights when required in low ambient areas.

• Wide area of survey 360° (5/8 meter detection at 2.8 meter height)• Adjustable settings: Light ON (since last detection) 10 sec - 12 min. Lux setting (ambient light intervention threshold) 5 - 350 lx

182182300000 10/2500 surface mounting internal PIR movement detector 888.00183182300000 10/2500 recessed mounting internal PIR movement detector 888.00

Occupancy sensors - incorporating “presence” and “movement” detection

Occupancy sensors supply voltage 110…230 VAC (50/60Hz)• Two sensors - “presence” (for zones of low activity) and “movement” (for transit areas)• Dual “push-in” termination for easy “looping” with other switches with pushbutton release• Supplied with all hardware for surface mounting or recess mounting• Adjustable settings: – Light ON (since last detection) 12 sec - 35 min. – Lux setting (ambient light intervention threshold) 5 - 350 lx – Sensitivity control for reduced sensing area

Passage way sensor (Ø) 84 x (D) flush: 44 / surface: 85 mm

• Rectangular areas - lobbies, corridors and walkways (sensing area 30 met x 4 met wide)

184182300300 10/2500 passage way internal movement and presence detector 1673.00

Ceiling mount sensor (Ø) 84 x (D) flush: 35 / surface: 76 mm

Responds to very small movements, suitable for use in offices, schools, and the workplace

• Wide sensing area 360° (4/8 meter detection at 2.8 meter height)• Two sensing areas: “presence” and “movement” detection

185182300300 10/2500 ceiling mount internal movement and presence detector 1369.00

12A28231

12618230

new


Engine / Generator controllers

Stand alone gen-set controllers• Generator voltage and current control• Engine protection• Programmable inputs and outputs• Programmable alarm properties

type digital digital description price inputs outputs

RGK400SA series 96 x 96 mm panel mounting (IP40)

– Universal supply: 12 / 24 VDC– Display: LCD icon display– Measurement voltage: 100 - 480 VAC– Current Input: 1PH, /5A or /1A– 1 analog resistance input for oil pressure / engine temperature or fuel level control– Single, two and three phase voltage control - L1-L2-L3-N– Customisable alarm text (2 alarms)– IR programming port on front panel for communication with PC– NFC technology for parameter setup via smartphone or tablet

RGK400SA 5 5 stand alone gen-set controller 3001.00

RGK420SA* 5 5 stand alone gen-set controller 3410.00

* Incorporates 3 position key switch (OFF, local start, remote start)

RGK 400SA accessories

Expansion modules (rear plug-in)EXP1040 additional - 2 digital / resistance inputs, 2 static outputs 1719.00EXP1041 additional - 2 thermocouple inputs, 2 static outputs 1797.00

EXP8005 housing gasket to increase protection to IP65 98.00

RGK600SA series 144 x 144 mm panel mounting

As above RGK400SA but with following additional features:

– Display: Graphic LCD 128 x 80 pixels with backlight– Measurement voltage: 100 - 480 VAC– Current Input: 3PH, /5A or /1A– Operating temperature: -30 - +70°C– 3 analog resistance input for oil pressure, engine temperature or fuel level control– Customisable alarm text (8 alarms)– Non-volatile memory for event storage– Modbus-RTU and Modbus-ASCII protocols

RGK600SA 4 6 stand alone gen-set controller 6138.00 with “W” or magnetic “pickup”for engine speed reading (no CANbus)

RGK601SA 4 6 stand alone gen-set controller 6502.00 with CANbus-J11939 (no “W” or magnetic “pickup”)



– Measurement voltage: 30 - 600 VAC (programmable VT ratio)– 3 analog resistance input for oil pressure, engine temperature or fuel level control– Single, two and three phase voltage control - L1-L2-L3-N– PLC logic for inputs, outputs and internal status– RS232 communication port

RGK700SA 6 7 stand alone gen-set controller 9321.00



– RS485 communication (no RS232 port)– Neutral current measurement range: 0.050…6A or 1.2A– 400Hz frequency support– 1 programmable analog input– Modbus-TCP communication protocol– Current leakage control– RTC clock-calendar– Expandable with rear plug-in expansion modules (see page F-5)

RGK800SA 6 7 full featured stand alone gen-set controller 11594.00RGK800

RGK700

RGK600

RGK 420SA

new


Pow

er q

ualit

y &

effi

cien

cy

Engine / Generator controllers

RGK900

Automatic mains failure (AMF) gen-set controllers• Automatic starting of generator and load switching to stand-by emergency source in case of mains failure• Supervision in “open transition” for contactors, motorised circuit breakers and changeover switches• Engine protection• Programmable inputs and outputs• Programmable alarm properties

type digital digital description price inputs outputs

RGK600 series 144 x 144 mm panel mounting

– Universal supply: 12 / 24 VDC– Display: Graphic LCD 128 x 80 pixels with backlight– Measurement voltage: 100 - 480 VAC– Current Input: 3PH, /5A or /1A– Single, two and three phase voltage control - L1-L2-L3-N– IR programming port on front panel for communication with PC– 3 analog resistance input for oil pressure, engine temperature or fuel level control– Customisable alarm text (8 alarms)– Non-volatile memory for event storage– Modbus-RTU and Modbus-ASCII protocols

RGK600 4 6 stand alone gen-set controller 6548.00 with “W” or magnetic “pickup”for engine speed reading (no CANbus)RGK601 4 6 stand alone gen-set controller 6911.00 with CANbus-J11939 (no “W” or magnetic “pickup”)RGK610* 4 6 stand alone gen-set controller (1 exp. slot) 7230.00 with “W” or magnetic “pickup”for engine speed reading (no CANbus)

* 1 slot to accept plug-in expansion modules EXP1010/1011/1012


As above RGK600 but with following additional features:- Measurement voltage: 30 - 600 VAC (programmable VT ratio)- IR programming port on front panel for communication with PC- PLC logic for inputs, outputs and internal status- RS232 communication port

RGK700 6 7 stand alone gen-set controller 9776.00


As above RGK700 but with following additional features:- RS485 communication (no RS232 port)- Neutral current measurement range: 0.050…6A or 1.2A- 400Hz frequency support- 1 programmable analog input- Modbus-TCP communication protocol- Current leakage control- RTC clock-calendar- Expandable with rear plug-in expansion modules (see page F-5 )

RGK800 8 10 full featured stand alone gen-set controller 12049.00

Paralleling controllers for mains - mains and generator - generator

• Mains-generator “closed transition” synchronising• Mains-generator load sharing with source peak demand control• Engine protection• Generator paralleling supervision (island mode with load sharing)

RGK900 series 180 x 240 mm panel mountingAs above RGK800 but with following additional features:- Voltage measurement range: 30-720 VAC- Frequency measurement range: 45…65Hz or 360…440Hz- Display: Graphic LCD 128 x 112 pixels with backlight- Customisable alarm text (16 alarms)- Modbus-RTU, Modbus-ASCII and Modbus-TCP communication protocols- 2 analog outputs for engine speed control (governor) / voltage regulator (AVR)- Built-in buzzer, multi-level passwords, sleep function- Expandable with rear plug-in expansion modules (see page F-5)

RGK900SA 13 10 full featured stand alone gen-set controller 28417.00RGK900 13 10 mains-generator paralleling control 28872.00Control of mains, automatic transfer switching and paralleling on multiple generators controlled by RGK900SARGK900MC 13 10 Mains-ATS (Automatic Transfer Switching) controller 22052.00

RGK 600


Pow

er q

ualit

y &

effi

cien

cy

Occupancy sensors

EE804

EE805

EE820

EE860

EE815

Occupancy sensors

• Detect movement• Measure ambient light• Automatically switch lights “on” (if ambient is below pre-set level and movement is detected)• Automatically switch lights “off” (if no movement is detected after a pre-set time delay period)• Complies with: IEC 60669-1 and IEC 60669-2-1 - Supply voltage: 230 VAC 50Hz - Switch current: 8/10/16A 230V (AC1) - Lux adjustment: 5 - 1000 lux

EE804 and EE805 motion detectors

EE804 and EE805 are 360° indoor movement detectors with a built-in light sensitive switchingfunction. Ideal for use in interior circulation areas such as corridors, entrance halls, bathrooms etc.

- Operating time delay: 5s - 15 min- Detection range: 6 meter radius (at 2.5 meters high) 360°

type mounting description rated price current

EE804 surface 105.5 mm dia. economical motion detector 8A 422.00EE805 flush 75 mm hole economical motion detector 8A 449.00

EE820 basic motion detectors (IP55)

Wall mounting with numerous mounting possibilities for indoor or outdoor applications.- Operating time delay: Pulse, 5s -15 min- Detection range: 16 met frontal /8 met lateral (at 2.5 meters high)EE820 surface 140° wall mnt. basic occupancy sensor 10A 567.00

EE860 enhanced motion detectors (IP55)

Offers vertical and horizontal adjustment and area limitation with shutters suitable for indoor or outdoor applications. Wall, inner/outer corner, ceiling mount. Setting and adjustments made via concealed potentionmeters or remote control.

- Operating time delay: 5s - 15min - Detection range: 16 met frontal / 10 met lateral (at 2.5 meters high) - Sensitivity adjustment: 20% - 100%

EE860 surface 220° wall mnt. basic occupancy sensor 16A 901.00

Accessories

EE825 corner mount accessory (inner/outer) EE820 62.00EE827 ceiling mount accessory EE820 81.00EE855 corner mount accessory (inner/outer) EE860 62.00EE806 IR remote control for enhanced series EE815/20 515.00

High-performance combined presence and motion detector

High-performance presence detectors combine detection of both presence and motion in an areaideally suited for offices where human presence is detected to maintain lighting level.Motion detection enhances the overall sensing range of the detectors.

EE815 compact flush mount presence detector

Compact super-flush device mounts through a 50 mm hole for very neat installation.Settings and adjustments made via concealed potentiometers or remote control.

- Operating time delay: 1 min - 1 hour - Detection range: Presence 5 meter radius (at 2.5 meters high) Motion 7 meter radius (at 2.5 meters high)

EE815 flush 60 mm hole 360° enhanced presence detector 16A 1159.00

EE810 surface flush mount presence detector

- Operating time delay: 1 min - 1 hour - Detection range: Presence 7 meter radius (at 2.5 meters high) Motion 13 meter radius (at 2.5 meters high) - Lux adjustment 5 - 1200 lux

EE810 flush dual sens 360° enhanced presence detector 16A 2216.00


Pow

er q

ualit

y &

effi

cien

cy

Power capacitors and rack system Made in Germany

275.100-10120

275.398-715401

275.186-516600

275.525-701400

Three-phase cylindrical capacitorsMKPg-275 three-phase power capacitors, dry self-healing dielectric, gas filled (N2) protecting windings from environmental influences extending life expectancy, permitting mounting in any position.

• Capacitance tolerance: -5 - +10%• Max. permissible current: 1.5 - 2 IN• Max. inrush current: 300 x IN• Dielectric losses: <0.2 W/kvar• Mounting position: Any position• Impregnant (filling) Inert insulation gas (N2) (completely harmless to the environment)• Protection: Overpressure disconnection facility• Standards: IEC/EN 60831, VDE 0560-46/47, CSA C22.2 - 190-M1985, UL - 810, GOST 1282-88

type kvar at: CN description dimensions (mm) price 400V 440V 480V μF 3 x (H) Ø

MKPg-275 three-phase cylindrical capacitors M12 base mounted fixing stud

400...480V three phase industrial capacitorsFor severe operating conditions or substantial voltage fluctuations

• Rated Voltage: 400…480V, 50 Hz• Temperature category: 60 -40°C - +60°C (Max: 24 hr average 50°C - annual ave 40°C)• Duty: Continuous (life expectancy > 150000 h)• Supplied with discharge resistors (except * require separate discharge module)

275.525-701400 2.0 2.5 3.0 14 3-ph capacitor 164 60 663.00275.523-502800 4.2 5.0 6.1 33 3-ph capacitor 196 60 708.00275.545-504000 6.2 7.5 8.7 40 3-ph capacitor 164 75 824.00275.546-505800 8.3 10.0 12.5 58 3-ph capacitor 230 75 904.00275.546-506800 10.0 12.5 15.0 68 3-ph capacitor 230 75 963.00275.556-508300 12.5 15.0 18.0 83 3-ph capacitor 230 85 1049.00275.266-511100 16.8 20.0 24.1 111 3-ph capacitor 230 95 1471.00275.278-513700 20.0 25.0 30.0 137 3-ph capacitor 245 100 1583.00275.186-516600 25.0 30.0 36.0 166 3-ph capacitor 230 116 1660.00275.389-519900* 30.0 36.0 43.0 199 3-ph capacitor 280 116 2166.00275.389-522100* 33.3 40.0 48.0 221 3-ph capacitor 280 116 2189.00

275.105-10100* discharge resistor module for 30/33 kvar 400V capacitor 3 x 100 kΩ 45.00

525V three phase capacitors

• Rated Voltage: 400…525V, 50 Hz• Temperature category: D -40°C - +55°C (Max: 24 hr average 45°C - annual ave 35°C)• Duty: Continuous (life expectancy 480V >150000 h 525V >100000 h)• Supplied with discharge resistors (except * require separate discharge module)

type kvar at: CN description dimensions (mm) 525V 480V 400V μF 3 x (H) Ø

275.535-601900 5 4.1 2.8 19 3-ph capacitor 164 65 750.00275.546-703800 10 8.3 5.8 38 3-ph capacitor 230 75 968.00275.548-605800 15 12.5 8.8 58 3-ph capacitor 245 75 928.00275.566-607700 20 16.7 11.6 77 3-ph capacitor 230 85 1473.00275.269-611500 30 25.0 17.4 115 3-ph capacitor 280 85 1600.00275.396-715400* 40 33.4 23.2 154 3-ph capacitor 230 136 2609.00

275.100-10120* discharge resistor module for 30/40 kvar 525V capacitor 3 x 120 kΩ 36.00

690V three phase capacitors

• Rated Voltage: 690…760V, 50 Hz• Temperature category: 60 -40°C - +60°C (Max: 24 hr average 50°C - annual ave 40°C)• Duty: Continuous (life expectancy > 150000 h)• * (Require separate discharge module)

type kvar at: CN description dimensions (mm) 690V 760V μF 3 x (H) Ø

275.185-402800* 12.5 15 27.6 3-ph capacitor 164 116 1522.00275.186-405600* 25 30 56 3-ph capacitor 230 116 1879.00275.39B-411100* 50 60 111 3-ph capacitor 295 136 3193.00

275.106-10180* discharge resistor module for above 690V capacitors 3 x 180 kΩ 45.00


Pow

er q

ualit

y &

effi

cien

cy

Made in GermanyPower capacitors and rack system

Power factor systems (automatic) 400/440VFor applications with varying capacitor requirements. An automatic reactive controller monitors the network and only switches capacitor banks when required, avoiding potential over or under compensation in a network.

FMSE series floor standing systems (138 - 975 kvar - 400V)

Complete ready-to-install system comprising following:• Suitably ventilated floor standing enclosure (thermostatically controlled roof mounted exhaust fan)• Mains isolator, door interlocking (with early make/late break auxiliary contact)• High end reactive control relay DCRG 8 (incorporating digital display of all important network parameters) Able to monitor all three phase voltage and current to providing accurate indication of: - Active, Apparent Power as well as Active, Reactive, Apparent Energy monitoring - Current and Voltage Harmonics analysis (up to 31st harmonic) - Calendar-clock with backup reserve power - Event logging: alarms, setup changes, events etc. (internal memory stores last 250 events) - Internal panel temperature monitoring - Expandable with up to 4 expansion modules for: additional steps, analog Inputs/Outputs, RS323, RS485, Ethernet, GPRS/GSM modem communication

type kvar at: steps (kvar) at 400V expands dimensions (mm) price 400V 440V 12.5 25 50 100 to (kvar) (H) (W) (D)

FMSE series floor standing complete power factor systems (440V capacitors)

• Reverse-flow roof mounted exhaust fan (improved cooling and ventilation of the entire panel)• Bottom cable entry (top entry available on request)• RC series racks heavy duty cylindrical capacitors, fusegear and busbars “special” capacitor switching contactors incorporating limiting inductances

FMSE13804 138 165 1 1 2 – 450 2180 600 630 55630.00FMSE17504 175 210 – 1 3 – 475 2180 600 630 60360.00FMSE20004 200 240 – 2 3 – 475 2180 600 630 66650.00FMSE23804 238 285 1 1 2 1 425 2180 600 630 73380.00FMSE27504 275 330 – 1 3 1 475 2180 600 630 78090.00FMSE30004 300 360 – 2 1 2 425 2180 600 630 84520.00FMSE33804 338 405 1 1 2 2 425 2180 600 630 91110.00FMSE37504 375 450 – 1 1 3 475 2180 600 630 95830.00FMSE40004 400 480 – 2 1 3 500 2180 600 630 102250.00FMSE43804 438 525 1 1 2 3 500 2180 600 630 108850.00FMSE47504 475 570 – 1 1 4 500 2180 600 630 113580.00FMSE50004 500 600 – – 2 4 – 2180 600 630 116950.00

FMSE53824* 538 645 1 1 2 4 975 2180 1200 630 147600.00FMSE57524* 575 690 – 1 1 5 975 2180 1200 630 152440.00FMSE67524* 675 810 – 1 1 6 975 2180 1200 630 170790.00FMSE77524* 775 930 – 1 1 7 975 2180 1200 630 188530.00FMSE87524* 875 1050 – 1 1 8 975 2180 1200 630 206880.00FMSE97524* 975 1170 – 1 1 9 – 2180 1200 630 224620.00


Remote monitoring devices

For remote monitoring and control of all electrical network parameters (including harmonics), panel internal temperature, alarms, events and all setup parameters. Plug-in communication modules simply plug into controller and are automatically configured,to offer various communication protocols.

EXP1011 opto-isolated RS232 plug-in communication expansion module 2197.00EXP1012 opto-isolated RS485 plug-in communication expansion module 2197.00EXP1013 opto-isolated ETHERNET with web server function expansion module 4381.00EXP1014 opto-isolated Profibus-DP plug-in communication expansion module 6820.00

De-tuned anti-harmonic reactors 400V, 50 Hz

Detuned reactors protect capacitors against harmonics, avoiding parallel resonance and amplification of harmonics flowing in the network.

• Detuning Degree: 7%, 189 Hz• Insulation: F class insulation, 155°C• Internal thermal protection: Thermal cutout (125°C) incorporated (on centre phase)• Reference standards: IEC/EN 60076-6, 61558-2-20

type kvar at: description dimensions (mm) 400V 440V Ln (mH) (H) (W) (D)

HFRA1207 12.5 15 anti-harmonic reactor 2.89 210 210 125 2875.00HFRA2507 25 30 anti-harmonic reactor 1.43 185 240 170 4050.00HFRA5007 50 60 anti-harmonic reactor 0.713 230 300 180 4990.00

EXP10 11

HFRA...

FMSE...


Power factor controllers

EXP...

CX 02

DCRG 8

DCRL...

New DCRL / DCRG power factor controllers incorporate latest technological advanced monitoring to provide accurate measurement and control of network parameters in power factor correction applications, providing total protection of capacitors and systems.

• Expandable through clip-in expansion modules (I/Os, Comm ports etc.)• High accuracy (TRMS) measurements with configurable alarms• Front optic interface port for programming, data download, diagnostics• Suitable for medium voltage systems (with VT’s)• Wide voltage measurement range: 50 - 720 VAC L-L, 50 - 415 VAC L-N• Configurable 1A or 5A current input• Capacitor overload protection• Panel over-temperature protection by internal sensor

type number expand description housing price of steps up to size (mm)

DCRL controllers 3, 5 and 8 step single phase CT connection

DCRL series power factor controllers with advanced functionality in a dedicated ultra compact housing, combine modern front design with ease of mounting and expandability.

- Backlit icon LCD display (alarm codes with scrolling text) - Voltage and current THD with single harmonic analysis up to 15° order

3 and 5 step controllers 1 expansion slot (H) 96 x (W) 96 x (D) 65 mmDCRL3 3 step 6 step panel mount power factor controller 96 x 96 3183.00DCRL5 5 step 8 step panel mount power factor controller 96 x 96 3683.00

8 step controllers 2 expansion slots (H) 144 x (W) 144 x (D) 44 mmDCRL8 8 step 14 step panel mount power factor controller 144 x 144 5320.00

DCRG controllers 8 step single and three-phase CT connection

DCRG series power factor controllers are designed to satisfy technical characteristics of modern electrical installation requirements in all industries and working conditions, to detectcritical operating conditions and offer total protection of power factor systems.

- 8 steps (expandable by up to another 8 steps with plug-in expansion modules)- Three current inputs permit per phase analysis of all electrical parameters of the installation- Quick CT programming function / Automatic identification of direction of CT current flow- Backlit graphic LCD display (permits reading in bar-graph and wave form format)- Connection to 1/3 ph lines, 3 ph + N and co-generation systems with 4 quadrant operation- Configurable for fast dynamic (thyristor) switching or a combination of static and relay

8 step controller 4 expansion slots (H) 144 x (W) 144 x (D) 44 mmDCRG8 8 step 18 step panel mount power factor controller 144 x 144 6517.00

EXP expansion modules (plug into rear of controller to add more functionality)

EXP series expansion modules add extra functionality to the controllers.DCRL 3/5 accepts one module - DCRG 8 accepts up to 4 modules - DCRL 8 accepts up to 2 modules

Inputs/outputsEXP1006* 2 relay outputs to increase number of capacitor steps 604.00EXP1007* 3 relay outputs to increase number of capacitor steps 1382.00EXP1000 4 opto-isolated digital inputs 1221.00EXP1001 4 opto isolated static outputs to increase number of static steps 1221.00EXP1002 2 opto-isolated digital inputs and 2 opto-isolated static outputs 1465.00EXP1003* 2 relay outputs rated 5A 250 VAC 1465.00EXP1004 2 opto-isolated analog inputs PT100 or 0/4-20mA or 0-10V or 0…±5mA 4393.00EXP1005 2 opto-isolated analog inputs 0/4-20mA or 0-10V or 0…±5mA 4393.00EXP1016 2 NTC 01 temperature measurements and 2 three phase current inputs 3954.00

CommunicationEXP1010* opto-isolated USB interface 2197.00EXP1011* opto-isolated RS232 interface 2197.00EXP1012* opto-isolated RS485 interface 2197.00EXP1013* opto-isolated Ethernet with web server function (only for 8 step controllers) 4381.00EXP1014 opto-isolated Profibus-DP interface 6820.00EXP1015 GPRS/GSM modem without antenna 5271.00

* Available for DCRL and DCRG others only available for DCRG

AccessoriesC2 PC - DCRL/DCRG connecting cable + EXP1011 module 697.00C9 cable PC - Analog modem connecting cable 913.00

CX01 PC - DCRL/DCRG connecting cable with USB dongle 2120.00CX02 PC - DCRL/DCRG Wi-Fi dongle 5297.00CX03 GSM Quad-band antenna for EXP1015 modem (800/900/1800/1900MHz) 944.00

CX 01


Power factor systems (automatic) Made in Germany

RCSE series power factor rack systemRC series power factor racks are designed for direct panel mounting onto vertical supports within floor standing electrical panels.

RCSE series rack design incorporates the following:• Sheet metal mounting frame for easy panel mounting (capacitors visible without having to remove rack)• Electronicon heavy duty “gas filled” cylindrical capacitors (with integrated discharge resistors)• Special capacitor switching contactors 400 VAC coil (230V on request)• Three-phase busbar mounted fuse holder with hinged fuse protection cover• Suitably rated HRC fuses for each phase of each capacitor bank• Incorporated busbar, supports and inter-connecting busbar links• Dimensions: from front of switchgear to front plate: 150 mm Behind front mounting plate: 320 mm Between vertical supports: 486 mm

type kvar at: description dimensions (mm) price 400V 440V 480V (H) (W) (D)

RCSE series single step racks (400...480V capacitors) fuse protection

RCSE01204* 12.5 15 18 single capacitor rack 270 555 470 4790.00RCSE01504 15 20 24 single capacitor rack 270 555 470 5370.00RCSE02004 20 25 30 single capacitor rack 270 555 470 5810.00RCSE02504* 25 30 36 single capacitor rack 270 555 470 6230.00RCSE03004 30 40 43 single capacitor rack 270 555 470 6870.00RCSE04004 40 50 58 single capacitor rack 270 555 470 9010.00RCSE05004* 50 60 72 single capacitor rack 270 555 470 9315.00RCSE06004 60 80 86 single capacitor rack 270 555 470 11315.00RCSE08004 80 100 115 single capacitor rack 270 555 470 16000.00RCSE10004* 100 120 144 single capacitor rack 270 555 470 17080.00

RCD series double-step racks (400...480V capacitors) separate fuse protection for each bankRCDE04024 2 x 20 2 x 25 2 x 30 double capacitor rack 270 555 470 9990.00RCDE05024 2 x 25 2 x 30 2 x 36 double capacitor rack 270 555 470 10680.00RCDE06024 2 x 30 2 x 40 2 x 43 double capacitor rack 270 555 470 11970.00RCDE08024 2 x 40 2 x 50 2 x 58 double capacitor rack 270 555 470 16370.00RCDE10024* 2 x 50 2 x 60 2 x 72 double capacitor rack 270 555 470 16950.00

RCDE03734* 12.5+25 15 + 30 18 + 36 double capacitor rack 270 555 470 9390.00RCDE06034 20 + 40 25 + 50 30 + 60 double capacitor rack 270 555 470 13160.00RCDE07534* 25 + 50 30 + 60 36 + 72 double capacitor rack 270 555 470 13870.00

* Preferred types

Wall mount power factor systems (automatic) 400/440V

For applications with varying capacitor requirements. An automatic reactive controller monitors the network and only switches capacitor banks when required, avoiding potential over or under compensation in a network.

WMSE series wall mount power factor systems (37 - 150 kvar - 400V)

Complete ready-to-install system comprising following• Reverse-flow fan ventilated wall mount enclosure, bottom cable entry (top entry on request)• Mains isolator, door interlocking (with early make / late break auxiliary)• Heavy duty three phase capacitors (with internal discharge resistors)• Reactive control relay DCRL 5 (digital display of all important electrical network parameters)• “Special” capacitor switching contactors incorporating limiting resistors• HRC fuse protection (per capacitor bank)

type kvar at: steps (kvar) at 400V expands dimensions (mm) 400V 440V 12.5 25 50 to (kvar) (H) (W) (D)

WMSE series wall-mount complete power factor systems (440V capacitors)

WMSE03704 37.5 45 1 1 – 87.5 700 600 300 18720.00WMSE05004 50 60 2 1 – 87.5 700 600 300 21440.00WMSE06204 62.5 75 1 2 – 87.5 700 600 300 23210.00WMSE07504 75 90 2 2 – 87.5 700 600 300 26060.00WMSE08704 87.5 105 1 3 – – 700 600 300 27830.00

WMSE10004 100 120 2 1 1 150 700 900 300 31220.00WMSE11204 112.5 135 1 2 1 150 700 900 300 33110.00WMSE12504 125 150 2 2 1 150 700 900 300 35830.00WMSE13704 137.5 165 1 1 2 150 700 900 300 36610.00WMSE15004 150 180 – 2 2 – 700 900 300 38370.00See overleaf for larger floor standing power factor systems

WMSE...


Pow

er q

ualit

y &

effi

cien

cy

new

Excellent power quality reduces energy loss, extending equipment life and lowering costs. In contrast, poor power quality caused by harmonics distortion, reactive power, or non-linear loads, tends to lower power reliability and utility. As many industries and applications continue to adopt a wide variety of electronic equipment to facilitate the production process, power quality distortion has become a common problem.

Improves power factorContinuously outputs and compensates reactive power in real time to maintain power factor >0.99 Provides cycle response <20ms and dynamic response <500us.Output current unaffected by the mains voltage fluctuation, providing stable support for mains voltage.

Suppresses harmonicsEliminates resonance problems, eliminating amplified harmonic current and voltage, extending component life cycle and protecting the system.

type rated rated description dimensions (mm) weight price current voltage (H) (W) (D) (kg)

APF2000 series - Active Power Filters

Delta’s Active Power Filter APF2000 is the key to a clean grid and more efficient production. Adopting industry’s highest standard 32-bit digital microprocessor to instantly compensate for all types of harmonics for ultimate power quality improvement.

• Harmonic current compensation• Reactive power compensation• Load imbalance compensation

The APF2000 is a perfect solution for harmonic distortion, voltage and current distortion, reactive power loss, load imbalances, Improved power quality, lower energy loss and maintenance costs.

Rated voltage: 200 - 480VCooling method: Force air cooling (fan cooling)Step time response: <300μsTotal response time: <20msHarmonic compensation: 2nd to 50th harmonicHarmonic comp. ratio: ≥95%Parallel configuration: 2 - 6 unitsCommunication: RJ45 (Ethernet), D-Sub (RS-232), RJ45 (RS-485)

Wall mounted bottom cable entry

APF050A43A-31 50A 200 - 480V active power filter 590 370 311 50 198314.00APF100A43A-31 100A 200 - 480V active power filter 1101 423 440 90 306240.00

Floor standing bottom/top cable entry

APF200A43A-31 200A 200 - 480V active power filter 2130 630 656 350 612852.00APF300A43A-31 300A 200 - 480V active power filter 2130 630 656 370 832788.00

SVG2000 series - Static Var Generator

SVG 2000 series is a current type Static Var Compensator (SVC). It is a full-bridge structure power module designed with a choke to allow direct connection to the power grid for power quality control.

Fundamentally, the SGV2000 generates output voltage to control the amplitude and phase of the output current. It absorbs or supplies the accurate amount of reactive power to the system and precisely regulates the reactive power output. The SVG2000 Series is capable of directly monitoring the AC power side of the current and it compensates the harmonic current or the surge current that occurs at impact load.

Rated voltage: 220 - 480V ±10%Cooling method: Force air cooling (fan cooling)Step time response: <500μsTotal response time: <20msHarmonic compensation: 2nd to 13th harmonicHarmonic comp. ratio: ≥95%Parallel configuration: 2 - 6 unitsCommunication: RJ45 (Ethernet), D-Sub (RS-232), RJ45 (RS-485)

type rated rated description dimensions (mm) weight kVAR voltage (H) (W) (D) (kg)

Floor standing bottom/top cable entry

SVG300A43A-11 300 kVAR 220 - 480V static var generator 2130 630 940 650 1102859.00SVG500A43A-11 500 kVAR 220 - 480V static var generator 2130 830 940 1200 1723218.00

Quality of supply

SVG500A43A-11

APF50A43A-31

APF200A43A-31

power quality f efficiency - electrahertz · power quality & efficiency generator controllers...

Documents