ppt slide for presentation
DESCRIPTION
ppt on pc operated robotTRANSCRIPT
![Page 1: Ppt Slide for Presentation](https://reader035.vdocument.in/reader035/viewer/2022062512/552e38284a795978658b48b8/html5/thumbnails/1.jpg)
PC OPERATED WIRELESS ROBOT
By: G.MURALI KRISHNA (07591A0481) G. MAHESH KUMAR (07591A0479)
![Page 2: Ppt Slide for Presentation](https://reader035.vdocument.in/reader035/viewer/2022062512/552e38284a795978658b48b8/html5/thumbnails/2.jpg)
Introduction
AIM : The Main Aim of This project is to control the robot with PC
through wireless.
Robot can move either Forward or Backward, Left or right through the set of Commands given from the PC.
![Page 3: Ppt Slide for Presentation](https://reader035.vdocument.in/reader035/viewer/2022062512/552e38284a795978658b48b8/html5/thumbnails/3.jpg)
TECHNOLOGY USEDThis project basically uses Radio frequency(RF) Technology to transmit and receive the data wirelessly
Radio frequency (RF) is a rate of oscillation in the range of about 30 kHz to 300 GHZ
RF Transmitter : RF transmitter are the electronic devices that create continuously varying electric current , encode sine waves , and broadcast radio waves.
RF Receiver: RF receivers are electronic devices that separate radio signals from one another and convert specific signals into audio, video, or data formats. RF receivers use an antenna to receive transmitted radio signals and a tuner to separate a specific signal from all of the other signals that the antenna receives.
![Page 4: Ppt Slide for Presentation](https://reader035.vdocument.in/reader035/viewer/2022062512/552e38284a795978658b48b8/html5/thumbnails/4.jpg)
HARDWARE REQUIREMENTS
TRANSMITTER SECTION:
•Microcontroller
•RF transmitter
•Encoder
•MAX 232
•PC
RECEIVER SECTION :
•Microcontroller
•RF receiver
•Decoder
•H-bridge
![Page 5: Ppt Slide for Presentation](https://reader035.vdocument.in/reader035/viewer/2022062512/552e38284a795978658b48b8/html5/thumbnails/5.jpg)
Block Diagram Transmitter
![Page 6: Ppt Slide for Presentation](https://reader035.vdocument.in/reader035/viewer/2022062512/552e38284a795978658b48b8/html5/thumbnails/6.jpg)
RECEIVER
![Page 7: Ppt Slide for Presentation](https://reader035.vdocument.in/reader035/viewer/2022062512/552e38284a795978658b48b8/html5/thumbnails/7.jpg)
REGULATED POWER SUPPLY:
![Page 8: Ppt Slide for Presentation](https://reader035.vdocument.in/reader035/viewer/2022062512/552e38284a795978658b48b8/html5/thumbnails/8.jpg)
MICRO CONTROLLER (AT89C51)
The AT89C51 is a low-power, high-performance CMOS 8-bit microcontroller with 4K bytes of in-system programmable Flash memory
Fig : - Pin diagram of AT89C51
![Page 9: Ppt Slide for Presentation](https://reader035.vdocument.in/reader035/viewer/2022062512/552e38284a795978658b48b8/html5/thumbnails/9.jpg)
at89c51 features:
•Compatible with MCS-51® Products• 4K Bytes of In-System Programmable (ISP) Flash Memory• 4.0V to 5.5V Operating Range• 128 x 8-bit Internal RAM• 32 Programmable I/O Lines• Two 16-bit Timer/Counters• Six Interrupt Sources• Full Duplex UART Serial Channel• Low-power Idle and Power-down Modes
![Page 10: Ppt Slide for Presentation](https://reader035.vdocument.in/reader035/viewer/2022062512/552e38284a795978658b48b8/html5/thumbnails/10.jpg)
RF Section
RF Transmitter: RF Receiver:
![Page 11: Ppt Slide for Presentation](https://reader035.vdocument.in/reader035/viewer/2022062512/552e38284a795978658b48b8/html5/thumbnails/11.jpg)
RF Section specifications
•The ST-TX01-ASK is Hybrid transmitter module
• Its specifications:
• Frequency Range: 315 / 433.92 MHZ.
•Supply Voltage: 3~12V.
•Output Power: 4~16dBm.
•Circuit Shape: Saw.
•The RX04 is an ASK Receiver module
•Its specifications:
•Integrated IF and data filters.
•Operation voltage: 5 Volts.
•Low power consumption.
•Operation temperature range : 10﹣ ℃ ~+ 60 ℃
![Page 12: Ppt Slide for Presentation](https://reader035.vdocument.in/reader035/viewer/2022062512/552e38284a795978658b48b8/html5/thumbnails/12.jpg)
RS 232 cable:
To allow compatibility among data communication equipment, an interfacing standard called RS232 serial cable is used. A serial cable is a cable that can be used to transfer information between two devices using serial communication
![Page 13: Ppt Slide for Presentation](https://reader035.vdocument.in/reader035/viewer/2022062512/552e38284a795978658b48b8/html5/thumbnails/13.jpg)
Max 232The data which we are entering in to the hyper terminal editor is available at the COM1 port. Then the data enters in to the MAX232 voltage converter via the RS232 cable. The MAX232 converts the voltage levels of the RS232 to the TTL level and then sends to the UART of the microcontroller. So the main duty of the max232 is for the voltage conversions.
RS-232 TTL Logic----------------------------------------------15V ... -3V <-> +2V ... +5V <-> 1+3V ... +15V <-> 0V ... +0.8V <-> 0
![Page 14: Ppt Slide for Presentation](https://reader035.vdocument.in/reader035/viewer/2022062512/552e38284a795978658b48b8/html5/thumbnails/14.jpg)
Each H-Bridge having two inputs. Micro controller gives input to H-Bridge to control the direction of the robot. Based on the given inputs to the H-Bridge, the motor will be rotates either in clock-wise or in anti-clock wise direction. So that the movement of the robot will be controlled.
![Page 15: Ppt Slide for Presentation](https://reader035.vdocument.in/reader035/viewer/2022062512/552e38284a795978658b48b8/html5/thumbnails/15.jpg)
SOFTWARE COMPONENTS
•EMBEDDED C•KEIL•PROTEUS
![Page 16: Ppt Slide for Presentation](https://reader035.vdocument.in/reader035/viewer/2022062512/552e38284a795978658b48b8/html5/thumbnails/16.jpg)
Transmitter schematic:
![Page 17: Ppt Slide for Presentation](https://reader035.vdocument.in/reader035/viewer/2022062512/552e38284a795978658b48b8/html5/thumbnails/17.jpg)
Receiver Schematic
![Page 18: Ppt Slide for Presentation](https://reader035.vdocument.in/reader035/viewer/2022062512/552e38284a795978658b48b8/html5/thumbnails/18.jpg)
Photograph of Project Kit:
![Page 19: Ppt Slide for Presentation](https://reader035.vdocument.in/reader035/viewer/2022062512/552e38284a795978658b48b8/html5/thumbnails/19.jpg)
CONCLUSION
The project “PC OPERATED WIRELESS ROBOT CONTROLLING” has been successfully designed and tested.
Secondly, using highly advanced IC’s and with the help of growing technology the project has been successfully implemented.
![Page 20: Ppt Slide for Presentation](https://reader035.vdocument.in/reader035/viewer/2022062512/552e38284a795978658b48b8/html5/thumbnails/20.jpg)
FUTURE ASPECTS
In this project, the robot controlling is done with the help of the PC through the RF communication. The RF modules which are using in this project are less range depending on the cost effective we are not preferring the other high range modules.
Wireless is finding a huge development in Communications. So this project can further be enhanced with the help GSM and zigbee etc communication technologies.
![Page 21: Ppt Slide for Presentation](https://reader035.vdocument.in/reader035/viewer/2022062512/552e38284a795978658b48b8/html5/thumbnails/21.jpg)
![Page 22: Ppt Slide for Presentation](https://reader035.vdocument.in/reader035/viewer/2022062512/552e38284a795978658b48b8/html5/thumbnails/22.jpg)
THANK YOU