•Dry gas seals are basically mechanical face seals

• consisting of a mating (rotating) ring and a primary (stationary) ring

• During operation, grooves in the mating ring generate a fluid-dynamic force

•causing the primary ring to separate from the mating ring, thus, creating a "running gap" between the two rings.

•A sealing gas is injected into the seal, providing the working fluid for the running gap and the seal between the atmosphere or flare system and the compressor internal process gas.

Dry Gas Seal Arrangement

Typical Dry gas seal

Seal Face of Dry gas

Theory of Non-ContactTheory of Non-Contact

Lift off of stationary ring achieved by increased pressure at the taper portion.

Demo

Dry Gas Seal Arrangement in K-2115/K-4115

Dry Gas Seal Arrangement in K-2115/K-4115

F 1

F 2

FIT

FLARE

SECONDARY&

SEPARATION GAS SUPPLYN2

PRIMARY SEAL GAS SUPPLY

FROM COMPRESSOR DISCHARGE

START UP SUPPLY N2PCV

PCV

FIT

Dry Gas Seal Supply Console - P&ID

Primary Seal Gas is, typically, Filtered gas from the compressor Primary Seal Gas is, typically, Filtered gas from the compressor discharge side, injected in to the Seal Chamber (the primary discharge side, injected in to the Seal Chamber (the primary inboard seal chamber)inboard seal chamber)A major part of the this injected gas will flow back to the A major part of the this injected gas will flow back to the compressor through the inner labyrinth at the process gas side.compressor through the inner labyrinth at the process gas side.This achieves the prevention of emissions from the compressor This achieves the prevention of emissions from the compressor to to the atmosphere.the atmosphere. A small quantity of gas will pass thro the dynamically A small quantity of gas will pass thro the dynamically separated gap of seal faces to the intermediate chamber between separated gap of seal faces to the intermediate chamber between the inboard &outboard sealsthe inboard &outboard sealsSince this cavity is vented, the rate ( quantity per minute) of gas Since this cavity is vented, the rate ( quantity per minute) of gas flowing out is measured downstream.flowing out is measured downstream.This is the indication of the leakage rate of the seal. This is the indication of the leakage rate of the seal. A minimum rate of leakage will be always present. Increase in A minimum rate of leakage will be always present. Increase in the rate of leakage beyond design limits indicates reduced seal the rate of leakage beyond design limits indicates reduced seal performance/ Efficiencyperformance/ Efficiency

Understanding Seal Gas Supplies to Dry Gas SealUnderstanding Seal Gas Supplies to Dry Gas SealPrimary SealPrimary Seal

Understanding Seal Gas Supplies to Dry Gas SealUnderstanding Seal Gas Supplies to Dry Gas Seal

Secondary Seal is a backup seal which seals the leakageSecondary Seal is a backup seal which seals the leakagefrom primary seal chamber from primary seal chamber

Nitrogen is injected in to this secondary Seal ChamberNitrogen is injected in to this secondary Seal ChamberThe Secondary Seal Functions as a safety seal to avoid emissions to The Secondary Seal Functions as a safety seal to avoid emissions to

atmosphere in case of excessive leakage in the primary seal atmosphere in case of excessive leakage in the primary seal

Separation seal ( Barrier seal) Separation seal ( Barrier seal) This seal also works in conjunction with a separation labyrinth This seal also works in conjunction with a separation labyrinth situated situated between the bearing housings and Seal Chambersbetween the bearing housings and Seal ChambersThe separation gas is also Nitrogen, injected in to the separation The separation gas is also Nitrogen, injected in to the separation labyrinthlabyrinthThe main purpose of Separation gas supply is to prevent the oil in The main purpose of Separation gas supply is to prevent the oil in the the bearing side from entering the seal Chamber. bearing side from entering the seal Chamber. Presence oil in the seal chamber will cause Presence oil in the seal chamber will cause

damage to the Dry gas seal componentsdamage to the Dry gas seal components

Secondary Seal Secondary Seal ( Containment seal )( Containment seal )

Operational Guide Lines –Dry Gas Operational Guide Lines –Dry Gas SealsSealsSeal Gas Supply QualitySeal Gas Supply Quality

The Quality of Gas fed to the seals must be clean and Dry- The Quality of Gas fed to the seals must be clean and Dry- Coalescing Filters to filter 2 microns shall be used in the Coalescing Filters to filter 2 microns shall be used in the Dry gas Supply Console. Pressure Drop across the Filters shall be Dry gas Supply Console. Pressure Drop across the Filters shall be monitored and filters must be renewed to achieve good seal performancemonitored and filters must be renewed to achieve good seal performance

Seal Gas Supply flowSeal Gas Supply flowThe seal gas supply flow must be sufficient enough to ensure that the seal isThe seal gas supply flow must be sufficient enough to ensure that the seal isSupplied with sufficient filtered gas during operation with excess gas going back Supplied with sufficient filtered gas during operation with excess gas going back in to the Compressor casing. This is will provide an ideal sealing environment in to the Compressor casing. This is will provide an ideal sealing environment to maintain the optimum seal performanceto maintain the optimum seal performanceSeal Gas Leakage TrendsSeal Gas Leakage Trends

Seal performance is monitored through leakage trends. Seal performance is monitored through leakage trends. Occasional SpikesOccasional SpikesIn the leakage due process parameter variations, shaft In the leakage due process parameter variations, shaft movement, speed changes are movement, speed changes are no cause for alarmno cause for alarm. But . But persistent trend of higher leakage may give a forewarning of seal persistent trend of higher leakage may give a forewarning of seal problems problems

11

Operational Guide Lines –Dry Gas SealsOperational Guide Lines –Dry Gas Seals 22

Reverse Rotation Reverse Rotation Reverse Rotation should be avoided as it will damage the Reverse Rotation should be avoided as it will damage the delicate parts of a Dry Gas Sealdelicate parts of a Dry Gas Seal

Reverse Pressure Reverse Pressure Reverse pressure under static condition will result in an increase in static leakage. Reverse pressure under static condition will result in an increase in static leakage. Under Dynamic condition, reverse pressure can result major damageUnder Dynamic condition, reverse pressure can result major damage to the Dry Gas Seal System components.to the Dry Gas Seal System components.

Slow RollSlow RollIn Turbine Driven compressors Slow roll below 1000 rpm be avoided. In Turbine Driven compressors Slow roll below 1000 rpm be avoided. The separation of seal faces will not be achieved under such condition. The separation of seal faces will not be achieved under such condition. Seal faces will be running with contact which will damage Seal faces will be running with contact which will damage the geometry of the grooves in the seal facethe geometry of the grooves in the seal face