preliminary evaluation of manufactured … - 02 (ocr...preliminary evaluation of manufactured sand...
TRANSCRIPT
PRELIMINARY EVALUATION OF MANUFACTURED SAND FROM FRANK W. WHITCOMB/WINOOSKI, VT.
FOR USE IN STRUCTURAL CONCRETE
REPORT 84-2 APRIL 1984
REPORTING ON WORK PLAN 83-C-7
STATE OF VERMONT AGENCY OF TRANSPORTATI ON
MATERIALS & RESEARCH DIVISION
P. J. GARAHAN, P.E. , SECRETARY OF TRANSPORTATION S. J . GAGE, P.E., DIRECTOR OF ENGINEERING & CONSTRUCTION
R. F. NICHOLSON, P.E . , MATERIALS & RESEARCH ENGINEER C. C. BENDA, P.E., STRUCTURAL CONCRETE ENGINEER
Prepared By:
W. L. Meyer, Technician C Structural Concrete Subdivision
Reviewed By:
R. F. Nicholson, P. E. Material s & Research Engineer
Date: - =o_4-..:...__-_.!./_0 __ -_'~_4-___ _
"The information contained in this report was compiled
for the use of the Vermont Agency of Transportation. Conclusions
and recommendations contained herein are based upon the research
data obtained and the expertise of the researchers, and are not
necessarily to be construed as Agency policy. This report does
not constitute a standard, specification, or regulation. The
Vermont Agency of Transportation assumes no liability for its
contents or the use t hereof. 11
; ;
TABLE OF CONTENTS
Abstract . .
Introduction
Materials
Procedures
Results . . . . . . . . . . ' . . . . . . . . . . . . . . . . . .
Summary & Conclusions
Recommendations .....
Appendix
1
2
4
6
8
12
13
Work Plan No. 83-C-7. . . . . . . . . . . . . . . . • . . . 14
iii
ABSTRACT
This report documents results of a preliminary investigation
of manufactured sand from the Frank W. Whitcomb Construction Corp.
quarry in Winooski, Vermont, for use in structural concrete.
Tests were performed to detetmine compliance with the requirements
of Section 704.01 of the Vermont Standard Specifications for Highway
and Bridge Construction. Concrete mixes containing the proposed new
material were examined for compressive strength and resistance to
freezing and thawing. Results of tests were compared to results
obtained from concrete mixes containing a reference fine aggregate .
Limited availability of the proposed new material necessitated
performing fewer tests than had been originally scheduled.
This report recommends that, when sufficient quantities of this
material are available, all tests originally planned for this evaluation
be completed and a final report prepared.
1
INTRODUCTION
This report documents results of a preliminary investigation
of manufactured sand, proposed for use in structural concrete. The request
for this evaluation was submitted by the Frank W. Hhitcomb Construction
Corp . of Bellows Fal ls, Vermont, which also requested the material be
evaluated for use in bituminous concrete.
The request indicated sufficient quantities of material were avail
able for testing purposes, but failed to state the source and location of
the material or the manufacturing process i nvolved.
It was eventually l earned the source of material was a quarry belong
ing to the Frank W. Whitcomb Construction Corp . , located in Winooski,
Vermont. Parent material from the quarry was transported to Rexnord, Inc.,
Milwaukee, Wisconsin, where the manufactured sand was produced, using a
Gyradisc crusher. Samples of the manufactured sand were available at the
Frank W. Whitcomb Construction Corp. facility in North Halpole, New Hamp
shire.
The request also indicated the Frank\~. \~hitcomb Construction Corp.
was aware that the proposed ma terial is currently prohibited from being
used as the only fine aggregate in bituminous or structural concrete .
Present specifications permit a combination of washed natural sand and
stone screenings, but limit stone screenings to not more than 50 percent,
by weight, of the com~ination.
The manufactured sand, as submi tted, failed to comply with grading
requirements for Section 704.01 FINE AGGREGATE FOR CONCRETE . Prior to .
its use in structural concrete mixes, the material was separated on appro
priate screens and recombined to provide a grading which met requirements.
Limited availability of t he materia l also required that fewer trial batches
2
be prepared than had been originally scheduled.
The modified performance- i n-concrete phase of this evaluation was
conducted in the Central Laboratory of the Materials and Research
Division, using coarse aggregate from the Winooski quarry and a reference
fine aggregate from Hinesburg Sand and Gravel Company, Inc., in Hinesburg,
Vermont. Results of tests performed on concrete containing the new fine
aggregate were compared wi th results obtained from concrete containing
the reference fine aggregate. The Class B concrete used in this evalua
tion was examined for compressive strength and resistance to freezing
and thawing .
A concurrent investigation of the proposed material, conducted by
the Bituminous Concrete Subdivision, is documented in Materials and
Research Division Report 83-4.
3
MATERIALS
The materials used in this investigation are as follows:
a. Coarse Aggregate :
3/4" Crushed Stone F. W. Wh i tcomb Construction Corp. Winooski, Vt .
b. Fine Aggregate:
A. Proposed New Aggregate {Manufactured Sand) F. W. Whitcomb Construction Corp. ~linooski, Vt.
B. Reference Aggregate Hinesburg Sand & Gravel Company, Inc . Hinesburg, Vt.
c. Cement:
Type II Glens Falls Portland Cement Co. Glens Fall s, N. Y.
d. Air Entraining Admixture:
Darex AEA W. R. Grace & Co. Cambridge, MA
e. Water Reducing Admixture:
WRDA with Hycol W. R. Grace & Co. Cambridge, MA
4
Aggregate properties used for preparing mix designs are shown in Tabl e 1 and Table 2.
TABLE 1 COARSE AGGREGATE PROPERTIES
Dry Rodded Bulk Absorption, Unit Heijht,
Specific Gravity percent lbs/ft
Reference Aggregate-Hhitcomb , t.Jinooski 2.78 0.4 100.32
TABLE 2 FINE AGGREGATE PROPERTIES
Bul k Absorption, Fineness Specific Gravity percent Modulus
Reference Aggrega te - 2.64 0.9 2. 72. Hinesburg S&G/Hinesburg
Manufactured Sand - 2.61 0.8 2.78 ~Jhi tcorrb/t.Ji nooski
5
PROCEDURES
Samples of the proposed new material were obtained from the manufac
turer and tested for compliance with Section 704.01. The material was
examined for gradation, organic impurities, and compressive strength of
mortar. Soundness test resul ts were obtained from the Bituminous Concrete
Subdi vision which conducted a concurrent evaluation of the material.
The specific gravity used to prepare mix designs was also obtained
from the Bituminous Concrete Subdivision.
Prel iminary gradation tests, which agreed with data submitted by the
manufacturer, indicated the material did not comply with requirements.
Prior to preparing trial batches, the material was separated on the appro
priate screens and recombined to provide an acceptable gradation.
Performance-in-concrete tests were conducted on concrete prepared in
the Central Laboratory. Mixtures were designed by Structural Concrete
Subdivision personnel for Class B concrete. Plans to investigate Class A
concrete were abandoned, due to a lack of sufficient new material.
Concrete used in this evaluation was mixed in a Sears rotary drum
mixer with batch size being one cubic foot. Two batches of Class B concrete
containing the new aggregate were prepared, as well as two batches of
Class B concrete containing the reference aggregate.
The mix proportions used are shown in Table 3.
6
TABLE 3
CLASS B CONCRETE MIX DESIGNS BATCH QUANTITIES PER CUBIC YARD
New Aqc reqate Bat ch 1 Batch
*Whitcomb Coarse Aggregate, 1bs 1686 1686 *Whitcomb Fine Aggregate, 1bs . 1405 1405 ~Hinesburg Fine Aggregate, 1bs. - -Cement, 1 bs. 611 611 Air Entraining Admixture, oz. 3.9 3.9 Water Reducing Admi xture, oz. 18.3 18. 3 Net \~ater gal. 37.2 37.3
2
*Wei ghts converted to saturated surface - dry condition
Reference Aqqreqate Batch 3 Batch 4
1686 1686 - -
1423 1423 611 611 3.0 3. 3
18.3 18. 3 34.8 34.3
Tests were performed on the f resh concrete to determine Sl ump (AAS HTO
T 11 9-82), Air Content (AASHTO T 152-82), and Unit Weight (AASHTO T 121-82 ).
Three test cylinders (6" x 12 11) and one freeze- thaw specimen (3" x 3" x 16")
were cast from each batch . The cylinders were tested for compress i ve
strength (AASHTO T 22-82) at 28 days. The f reeze-thaw specimens were moist
cured for 14 days , after which they were subjected to 500 cycles of freezing
and thawing (AASHTO T 161 -82) in a 3% NaCl solution.
7
D.>;;o ~Cl) ~ Vl "1C: Cl) _.
~ rt-D.>Vl rt-roo
....... Q.l
a. Gradation (AASHTO T 27-82) "1rt-Cl)Cl)
Vl D.lrt-VlVl
-.....o o:;:, _. - rt-Proposed New Aggregate 0:::1" ~Cl) Vl .. -o
Bituminous Structura 1 Laboratory V.A.O.T. Manufacturer•s Concrete Concrete Graded Reference S.pecification
Data Subdivision Subdivision Material Aggregate Requirements !
"1 0 -o 0 Vl Cl) 0.. ;;o
(X)
Sieve Size % Passing ; % Passi ng % Passinq % Passing % Passing % Passing I
3/8 11 100 100 100 100 100 100 i No. 4 100
I
100 100 100 . 98 95-100
,..., :;:, (/) Cl) c ~ .-
-i ....... (/) .... :;:, Cl)
No . 8 92 ' 95 94· 94 81 - Q.l ~
No. 16 53 : 63 59 60 68 50- 80 No. 30 32 38 36 35 49 25- 60
~ "1 Cl) ~
No. 50 20 : 24 23 23 24 10- 30 Q.l rt-
No . 100 11 14 13 10 8 2- 10 Cl)
No. 200 I 5 5 5 3 2 - Q.l :;:, 0..
Fineness I. Modulus I
2. 92 2.66 2.75 2.78 2.72 2.60- 3.10 I
l "1 Cl)
....... Cl) "1 Cl) :;:, - - -- --() Cl)
....... .... ::1 Cl)
b. Organic Impurities (AASHTO T 21-81)
Proposed New Reference
Aggregate Aggregate
Color Plate <1 1
c. Compressive Strength of Mortar
(1) Proposed new aggregate test results .
Proposed Proposed New
Ottawa New Aggregate, Sand, Aggregate, percent of
Avg. psi Avg. psi Ottawa Sand
3 days 2680 4540 169
7 days 3260 4950 152
(2) Reference aggregate test results.
Reference Ottawa Reference Aggregatet Sand, Aggregate, percent of
Avg. psi Avg. psi Ottawa Sand
3 days 2400 4170 174
7 days 3050 5050 166
d. Soundness, Using Sodium Sulfate (AASHTO T 104-77)
*Proposed New
Aggregate, percent loss
6.0
Reference Aggregate,
percent loss
2. 2
V.A.O.T. Speci fica ti on
Reguirements
2 maximum
V.A. O.T . Spec. Subsection 704.0l(c)
Requirements, r>ercent of Ottawa Sand
100 minimum
100 minimum
V .A.O. T. Spec. Subsection 704.0l(c)
Requirements, percent of Ottawa Sand
100 minimum
100 minimum
V.A.O.T. Speci fica ti on Requirements, percent loss
8 maximum
*Resul ts from Materials & Research Division Report 83-4
9
Coarse aggre~ate test results are as follows:
a. Gradation (AASHTO T 27-82)
Sieve Size
1" 3/4" 3/8"
No. 4 No. 8
3/4" Crushed Stone
Percent Passing
100 99 26 4 1
b. Thin and/or Elongated Particles (VT AOT-MD 22)
3/4" Crushed Stone; percent
3.0
V.A.O.T. Speci fi ca t ion Requirements
Per.cent Passing
100 90-100 20- 55 0- 10 0- 5
V.A.O.T. Specification Requirements ,
percent
10 maximum
c. Los Angeles Abrasion, "B" Gradi ng (AASHTO T 96-77)
3/4" Crushed Stone, percent loss
15. 1
V.A.O.T. Speci fica ti on Requirements, percent loss
35 maximum
d. Soundness, Usi ng Sodium Sulfate (AASHTO T 104-77)
3/4" Crushed Stone, percent loss
0.3
V.A.O.T. Speci fi cation Requ i rements, percent loss
8 maximum
The results of tests on the fresh and hardened concrete are shown in Table 4.
10
TABLE 4
CLASS B CONCRETE TEST RESULTS
New Ag' reg ate Reference Aggreg_at~
·satch 1 Batch 2 ·satch 3 Batch 4
51 ump, inches 3 2 1/2 3 1/2 4 3/4 Air Content, percent 5.0 5.1 4.8 5.3 Unit Weight, 1bs/ft3 146.1 146.1 - 147 . 7 Temperature, OF 72 72 74 70
*Compressive Strength, psi 28 days 5871 5986 5836 5600
Freeze-Thaw Durability We ight Loss, percent
@ 250 cycles 5.3 3.9 5.4 3.6 @ 500 cycles 7. 1 6. 1 9.5 7.7
Durability Factor @ 500 cycles 88.2 95. 1 73.4 95.8
*Design Compressive Strength 3500 psi
11
SUMMARY AND CONCLUSIONS
1) The sample of proposed new aggregate, submitted by the manufacturer,
contained an excess of material passing the No. 100 sieve. All
other aggregate test results complied with specification requirements.
2) The net water (see Table 3) required with the New Aggregate batches
exceeded the "Maximum Water Cement Ratio" permitted by specifications.
The average 37 . 25 gal/yd3is equal to a water/cement ratio of .51 . The
maximum allowable water/cement ratio for Class B concrete is .49 . The
net water also averaged 2.75 ga1/yd3 higher than that required in the
reference concrete. The increased water demand can generally be at
tributed to the greater angularity of the aggregate particles, when
compared to natural sand.
3) The angularity of the aggregate particles is also considered to be
responsible for the increased quantity of air entraining admixture
required in the concrete batches containing the manufactured sand.
4) The compressive strength of concrete containing the manufactured sand
was slightly higher than the strength of the concrete containing the
reference aggregate.
5) The concrete containing the manufactured sand showed slightly less
weight loss in freeze-thaw testing when compared to the concrete con
taining the reference aggregate. Sonic testing produced variable
results. Testing indicated the first batch of concrete containing
the manufactured sand and the first mixture ~ith the reference
aggregate were less durable than their respective second batches .
12
RECOMMENDATIONS
. Should the Frank W. Whitcomb Construction Corp. install
the necessary equipment and begin producing manufactured sand
at the Winooski, Vermont quarry, the following recommendations
should be carried out:
1. The evaluation be continued until all tests originally
scheduled are completed.
2. Prepare a final report documenting results of all tests
and make recommendations relative to possible future use
of the proposed new material including, if necessary,
changes in specifications.
13
TA 565 Rev. 4/79 APPENDIX
STATE OF VE!UiotU AGENCY OF TRANSPORTATION
MATERIALS & RESEARCH DIVISION
RESEARCH INVESTIGATION
Work Plan Uo. 83-C-7
Prepared By: W. Meyer ' Date: 2/3/83 quJ-1'/1 Sheet 1 of 2
Subject Evaluation of a Proposed New Fine Aggregate, Frank W. Whitcomb Canst. Corp. Winooski, Vt.
Investigation Reques t ed By Fran k W. Whitcomb Cons. CorpDate December 10, 1982-
Date Information Required. ____ ~A~s~s~o~o~n~a~s~p~o~s~s~ib~l~e~-------------------------
Purpose of Investigat ion To evaluate a new fine aggregate (manufactured sand)
from the Frank W. Whitcomb Construction Corp., Winooski, Vermont quarry
for use as a structural .concrete aggregate. ·
Proposed Tes ts or Evaluation Procedure~----------------------------------
See Vermont Procedure For Evaluating a New Source of Structural Concret~
Aggrega'te, VT-AOT-MRD 9-82. This procedure will be used as a guide for
investigating the proposed new material. Several modifications may be
necessary to tomplete the required evaluation, including:
(1) Material already examined failed to meet grading requirements.
Rescreening may be necessary to achieve an acceptable
gradation.
(See sheet two)
D. Brow~ Proposal Discussed With R. Frascoi~ Projected Manpower Requirements 40 man days
Investigation To Be Conducted By Structural Concrete Subdivision
Proposed Starting Date February 15, 1983 Estimated Completion Date May 25. 1983
Engineer~~4~ 2-jl--f:) by Materials Engineer __________________________________________ _
Mater i a l s & Research Division Agency of 7ranspor t a tion f1.:lh:> Tv f' o ri· FPhr11.:1 rV 3. 1983
14
Vt. Agency of Transportation Research Investigation APPENDI X, con't. Work Plan No. 83-C-7
February 3, 1983 . Page 2 of 2
(2) Initial performance-in-concrete tests will be performed using two batches each of Class A and Class 8 concrete containing the proposed new aggregate and two batches each of Class A and Class 8 concrete containing a reference aggregate.
(3) Present specifications permit not more than 50%, by weight, of stone screenings. The fine aggregate proposed consists of 100% crushed material. Additional performance-in-concrete tests, using various proportions of the proposed new material blended with a reference washed natural sand, may be necessary in order to establish a mix design to be evaluated under field conditions.
(4) Conduct a field evaluation of ready mixed concrete containing the proposed new material, or blended new material, to examine slump, air content, compressive strength, workability and finishing characteristics.
Prepare a progress report at the completion of each phase of the evaluation, and a final report when all testing has been completed.
15