prepking - gratis exam · prepking number : 642-185 passing ... b. configuring midlet for cts in...

PrepKing

Number: 642-185Passing Score: 800Time Limit: 120 minFile Version: 7.5

http://www.gratisexam.com/

PrepKing 642-185

Exam A

QUESTION 1Which statement is incorrect?

A. Cisco TelePresence System is a SIP phone from the CUCM perspective.B. Configuring MIDlet for CTS in the CUCM is similar to configuringf any other phone serice.C. Cisco Telepresence cannot interoperate with standard based video conferencing endpoints.D. Joining a Cisco TelePresence meeting can be done with one touch of a button on the Cisco IP phone.

Correct Answer: CSection: (none)Explanation

Explanation/Reference:

QUESTION 2Which device will cause a Cisco TelePresence call to drop if not plugged in?

A. microphoneB. camera HOMIC. camera EthernetD. sprakerE. Auto-Collaborate cable

Correct Answer: ESection: (none)Explanation


QUESTION 3Refer to the exhibit. The customer network has blue and red VSANs redundantly connected, Path A having a 4-ISL port channel and Path B having a 2-ISL port channel. Changes to the physical topology are not allowed forthe next six months. All the traffic now flows over Path A with congestion occurring on both VSANs at peaktimes. The blue VSAN is, on the average, generating four times the amount of data than that of the red VSAN.How can the blue and red VSAN traffic be spearted over the two paths, while preserving redundancy?

Build Your DreamsPassGuide 642-185

A. Make a zone in the blue VSAN with only ISL ports on Path B, and make another zone in the red VSAN withonly ISL ports on Path A.

B. Make a zone in the blue VSAN with only ISL ports on Path A, and make another zone in the red VSAN withonly ISL ports on Path B.

C. In the blue VSAN, give Path B a lower FSPF cost than Path A; in the red VSAN, give Path A a lower FSPFcost than Path B.

D. In the blue VSAN, give Path A a lower FSPF cost than Path B; in the red VSAN, give Path B a lower FSPFcost than Path A.



QUESTION 4Which ephone-dn type does the picture represent?


A. shared ephone-dnB. overlaid ephone-dnC. two ephone-dns with one numberD. single-line ephone-dn



QUESTION 5Refer to the exhibit. The routers are running RIPv2. Which addressing scheme would satisfy the needs of thisnetwork yet waste the fewest addresses?


A. Network 1: 192.168.10.0/26Network 2: 192.168.10.64/26Network 3: 192.168.10.128/26Serial link 1: 192.168.20.0/24Serial link 2: 192.168.30.0/24

B. Network 1: 192.168.10.0/26Network 2: 192.168.10.64/28Network 3: 192.168.10.80/29Serial link 1: 192.168.20.88/30Serial link 2: 192.168.30.96/30

C. Network 1: 192.168.10.0/26Network 2: 192.168.10.64/27Network 3: 192.168.10.96/28Serial link 1: 192.168.10.112/30Serial link 2: 192.168.10.116/30

D. Network 1: 192.168.10.0/27Network 2: 192.168.10.64/28Network 3: 192.168.10.96/29Serial link 1: 192.168.10.112/30Serial link 2: 192.168.10.116/30



QUESTION 6Which three options should be used to accommodate burst on a Cisco TelePresence call? (Choose three.)

A. Ask your provider to increase the Tc of their policers.B. Buy 20% more bandwidth so that the bursts are invisible to the provider.C. Implement shaping on the WAN interfaces to shape the bursts down to conform to the Build Your Dreams

PassGuide 642-185service provider's police policy.

D. Policing on the WAN interfaces to limit the bursts to conform to the service provider's policy.E. Remark TelePresence traffic as discard ineligible.

Correct Answer: ABCSection: (none)Explanation


QUESTION 7Which QoS mapping is specific to Cisco TelePresence?


A. CoS 5 to map to a DSCP value of 40B. CoS 4 to map to a DSCP value of 46C. CoS 3 to map to a DSCP value of 48D. CoS 5 to map to a DSCP value of 16E. CoS 4 to map to a DSCP value of 32



QUESTION 8Refer to the exhibit. Which statement describes DLCI 17?

A. DLCI 17 describes the ISDN circuit between R2 and R3.B. DLCI 17 describes a PVC on R2. It cannot be used on R3 or R1.C. DLCI 17 is the Layer 2 address used by R2 to describe a PVC to R3.D. DLCI 17 describes the dial-up circuit from R2 and R3 to the service provider.



QUESTION 9Refer to the exhibit.


Identify the port number where the HFR (Presentation) Codec Ethernet should connect.

A. 4B. 5C. 6D. 7E. 9F. 10G. 11H. 12I. 13

Correct Answer: C

Section: (none)Explanation


QUESTION 10Refering to the configuration for vs1. the 172.26.26.51 host OS fingerprinting is manually configured as whichoperating system type?

A. LINUXB. AIXC. SOLARISD. WINDOWS

Correct Answer: DSection: (none)Explanation


QUESTION 11Build Your DreamsPassGuide 642-185

After Cisco TelePresence Manager is configured for MicroSoft Exchange 2003, what must be done to move theconfiguration to support IBM Lotus Notes?

A. The Cisco TelePresence Manager must be reinstalled.B. The MicroSoft Exchange configuration must be modified to reflect the new IBM Lotus Notes server settings.C. The MicroSoft Exchange configuration must be reinstalled.D. This move is not supported.

Correct Answer: ASection: (none)Explanation


QUESTION 12You want to allow IP Phones in subnet 10.100.1.0 to register with Cisco Unified Communications ManagerExpress at address 10.10.1.1. Which two commands should you use?

A. ip helper address 10.10.1.1 under interface FastEthernet0/0.100B. option 150 ip 10.10.1.1 under dhcp pool PhonesC. default-router 10.100.1.1 under dhcp pool PhonesD. subnet prefix-length 24 under dhcp pool Phones


Correct Answer: BCSection: (none)Explanation


QUESTION 13Refer to the exhibit. What should be entered in the Name field when configuring Cisco Unified CommunicationsManager to control voice port T1 1/0/0 in BR2_GW?

A. S0/DS1-0@BR_GWB. BR2_GWC. 10.2.120.1D. S0/DS1@SDA0012005FEEF0

Correct Answer: BSection: (none)Explanation


QUESTION 14What type of trunk is required between the Cisco Unified Communications Manager where Cisco TelePresencedevices are registered and the Cisco Unified Videoconferencing MCU to support Cisco TelePresenceinteroperability?

A. SCCPB. H.323C. SIPD. H.323 to SIP



QUESTION 15A Cisco TelePresence solution is built based on SIP protocol. Which three links are configured


as SIP trunks? (Choose three.)

A. CTS endpoint to CUCMB. CTMS to CUCMC. Cisco IP Phone 7975 or 7970 to CUCMD. CUCM to CUBEE. CTRS to CUCM

Correct Answer: BDESection: (none)Explanation


QUESTION 16When a Cisco TelePresence endpoint participates on a call with 720p Best video quality, what video format isused on the camera, encoder, and display respectively?

A. 720p60, 720p, 720p60B. 720p30, 720p, 720p60C. 1080p30, 720p, 720p60D. 1080p30, 720p, 1080p60



QUESTION 17You need configure PSTN voice gateway. Which two dial peers will correctly route calls to emergency services?

A. dial-peer voice 1 potsdestination-pattern 9911prefix 911Build Your DreamsPassGuide 642-185port 1/0/0

B. dial-peer voice 2 portsdestination-pattern 911forward-digits allport 1/0/0

C. dial-peer voice 2 potsdestination-pattern 9911forward-digits allport 1/0/0

D. dial-peer voice 2 portsDesrtination-pattern 911Forward-digits 3Port 1/0/1

Correct Answer: ABSection: (none)Explanation


QUESTION 18At a minimum, what must an administrator configure in the CUCM for Cisco TelePresence Multipoint Switch?

A. SIP trunk and route patternB. H .323 gateway and route patternC. H.323 gateway, router pattern, route list and route groupD. SIP trunk, route pattern, route list and route groupE. H.323 gateway, route pattern and route groupF. route pattern, route list and route group



QUESTION 19Given the following:Cisco TelePresence endpoint A: CTS-3000Cisco TelePresence endpoint B: CTS-1000Cisco TelePresence endpoint C: CTS-1300Cisco TelePresence endpoint D: CTS-1000Cisco TelePresence endpoint E: CTS-1000For a multipoint meeting between these endpoints with room switching, endpoint A calls in first, followed byendpoint B, then endpoint C, then endpoint 0, and then endpoint E. Then endpoint B drops from the call.On which screen will Cisco TelePresence endpoint A see Cisco TelePresence endpoint E?

A. leftB. center

C. rightBuild Your DreamsPassGuide 642-185

D. randomly



QUESTION 20Which two protocols are used by the Cisco TelePresence Manager to communicate with the Cisco UnifiedCommunications Manager? (Choose two.)

A. AXL/SOAPB. XML/SOAPC. LDAPD. WebDavE. CTIF. SNMP

Correct Answer: AESection: (none)Explanation


QUESTION 21Which protocol is used by the primary codec to download its configuration from the Cisco UnifiedCommunications Manager?

A. TFTPB. SFTPC. HTTPD. HTTPS



QUESTION 22Refer to the exhibit. What would happen if one of the power supplies failed?


A. There would be no disruption regarding MDS operation.B. The MDS would shut down the standby supervisor to compensate for the power loss.C. The MDS would reset the failed power supply in an attempt to resolve the problem.D. Due to insufficient power, the MDS would shut down some modules.



QUESTION 23If the neighboring room produces 72 dB of noise, what would the minimum STC rating of the diving wall need tobe to block the noise?

A. 50B. 60C. 70D. 80



QUESTION 24What are the two choices for focal distance on a CTS-500? (Choose two.)

A. 3.5 feetB. 4 feetC. 6 feet

D. 8 feetE. 8.5 feet




QUESTION 25Given the following:Cisco TelePresence endpoint A: CTS-3000Cisco TelePresence endpoint B: CTS-1000Cisco TelePresence endpoint C: CTS-1300Cisco TelePresence endpoint 0: CTS-1000For a multipoint meeting between these endpoints with room switching, endpoint A calls in first, followed byendpoint B, then endpoint C, and then endpoint O. On which screens will Cisco TelePresence endpoint A seeCisco TelePresence endpoints B, C, and 0 respectively?

A. left, center, rightB. center, left, rightC. right, center, leftD. center, right, leftE. randomly



QUESTION 26What is the recommended height of the customer-supplied table for the CTS-1 000, CTS-11 00, and CTS-1300?

A. 26 in (66cm)B. 30 in (76cm)C. 36 in (91cm)D. 42 in (107cm)



QUESTION 27CIF has which video resolution?

A. 176 × 144B. 352 × 288

C. 704 × 576D. 1920 × 1080



QUESTION 28The packet loss threshold is determined by calculating the number of packets lost in a given


time period. How long is the time period?

A. 33 msB. 125msC. 165msD. 1 sE. 10 s



QUESTION 29What three ways can you connect an endpoint to a Static meeting on the Cisco TelePresence MultipointSwitch? (Choose three.)

A. CTS uses One Button to PushB. CTS systems manually dialC. meeting administrator adds CTS systems using the WebUID. system administrator dials the CTS system into the meeting using the CTS CLI.

Correct Answer: BCDSection: (none)Explanation


QUESTION 30How many CUVC 35XX MCUs can be configured in the Cisco TelePresence Manager?

A. 1B. 2C. 3D. unlimited number



QUESTION 31Refer to the exhibit. The Lakeside Company has the internetwork in the exhibit. The administrator would like toreduce the size of the routing table on the Central router. Which partial routing table entry in the Central routerrepresents a route summary that represents the LANs in Phoneix but no additional subnets?


A. 10.0.0.0/22 is subnetted, 1 subnetsD10.0.0.0 [90/20514560] via 10.2.0.2, 6w0d, Serial0/1

B. 10.0.0.0/28 is subnetted, 1 subnetsD10.2.0.0 [90/20514560] via 10.2.0.2, 6w0d, Serial0/1

C. 10.0.0.0/30 is subnetted, 1 subnetsD10.2.2.0 [90/20514560] via 10.2.0.2, 6w0d, Serial0/1

D. 10.0.0.0/22 is subnetted, 1 subnetsD10.4.0.0 [90/20514560] via 10.2.0.2, 6w0d, Serial0/1

E. 10.0.0.0/28 is subnetted, 1 subnetsD10.4.4.0 [90/20514560] via 10.2.0.2, 6w0d, Serial0/1

F. 10.0.0.0/30 is subnetted, 1 subnetsD10.4.4.4 [90/20514560] via 10.2.0.2, 6w0d, Serial0/1



QUESTION 32Which two frame rates can be used by Cisco TelePresence for auxiliary video encoding? (Choose two.)

A. 5B. 24C. 29.95D. 30E. 33F. 60


Correct Answer: ADSection: (none)Explanation


QUESTION 33Which two LDAP configurations are supported in Cisco TelePresence Manager intergration? (Choose two.)

A. Multiple Exchange Servers exists within a single forest and a single domain.B. Multiple Exchange Servers exists within a multiple forest and a single domain.C. Multiple Exchange Servers exists within a single forest and a multiple domain.D. Multiple Exchange Servers exists within a multiple forest and a multiple domain.

Correct Answer: CDSection: (none)Explanation


QUESTION 34On a Cisco TelePresecnce CTS-3000, where does audio for the left and right segments connect?

A. the primary codecB. the secondary codecsC. the Cisco TelePresence displaysD. the Cisco TelePresence Manager



QUESTION 35Which two Cisco TelePresence component types require B02.3af to operate in the default configuration?(Choose two.)

A. video camera

B. microphoneC. aux control unitD. AN expansion boxE. LED lightsF. Cisco IP Phone

Correct Answer: AFSection: (none)Explanation


QUESTION 36Which two Cisco TelePresence component types require 802.3af to operate in the default configuration?(Select two.)

A. video cameraB. microphoneC. aux control unit


D. A/V expansion boxE. LED lightsF. Cisco IP Phone

Correct Answer: AFSection: (none)Explanation


QUESTION 37Which are two continuity components that will read visually on camera? (Choose two.)

A. HVACB. room colorC. lighting color temperatureD. acoustic quality



QUESTION 38Refer to the exhibit. You have six IP phones configured to use MRGL_CFB. There are currently fiveconferences in progress. What will happen if the sixth IP phone tries to initiate a conference?

A. the conference will use SW_CFB_3 since it is the default and is not assigned to MRGL_CFBB. the conference will be attempted until the MRGL timer expiresC. the first conference resource that becomes available will be used for conference 6D. the conference will be rejected because there are no conference resources left


Explanation/Reference:Build Your DreamsPassGuide 642-185

QUESTION 39What levels of administration are available in the Cisco TelePresence Manager?

A. Administrator, Meeting Scheduler and Diagnostic TechnicianB. Administrator and Meeting SchedulerC. Administrator, Concierge, and Diagnostic TechnicianD. Administrator and ConciergeE. Meeting Scheduler and Diagnostic TechnicianF. Concierge, Meeting Scheduler and Diagnostic Technician



QUESTION 40Which three tools are on the recommended list for installing a Cisco CTS-3000? (Choose three.)

A. metric socket set with 16 mm to 22 mm socketsB. standard socket set with 1/2 in to 15/16 in socketsC. metric wrenches with 10 mm to 15 mm sizes

D. standard wrenches with 3/8 in to 7/8 in sizesE. levelF. tape measure

Correct Answer: CEFSection: (none)Explanation


QUESTION 41Refer to the exhibit. The mobile phone is unable to call the PSTN phone using the Mobile Voice Access feature.The mobile phone user hears "Your call cannot be completed as dialed ....." Which two CSSs combine todetermine whether access to the partition that is assigned to the PSTN route pattern is allowed? (Choose two.)


A. the Gateway CSSB. the Phone Device CSSC. the Remote Destination Profile CSSD. the Remote Destination Profile Rerouting CSSE. the Phone Line (DN CSS)

Correct Answer: CESection: (none)Explanation


QUESTION 42Which four Cisco TelePresence Systems support collaboration using the WolfVision document camera?

(Choose four.)

A. CTS-500B. CTS-1000C. CTS-1100D. CTS-1300E. CTS-3200

Correct Answer: ABCESection: (none)Explanation


QUESTION 43Which is a design requirement for Cisco TelePresence room aesthetics?

A. Every room should be identical.B. Maintain continuity in appearance among rooms.C. Carpet patterns and textures match from room to room.D. All rooms should be painted brown.


E. The only wall treatment should be paint.



QUESTION 44How do you calibrate the light meter from the Cisco recommended RRA tool kit?

A. Press the Auto Adjust button on the meter.B. Turn the meter on and off.C. Cover the sensor with the cap and press the Zero button.D. Cover the sensor with the cap and press the Light Source button.



QUESTION 45Which identifies the amplitude of an analog signal stream?

A. AB. C

Correct Answer: Section: (none)Explanation


QUESTION 46A customer has a static multipoint call setup. They have five separate Cisco CTS-3000 units connected to thismeeting: Seattle, Denver, Dallas, Houston, and Austin. The meeting is working fine, but when the AustinTelePresence room dropped off the call 30 minutes early, all endpoints dropped. When the other four roomscall back into the static multipoint meeting, they are only seeing an hourglass in the lower right corner of thescreen. Which is the cause of the problem?

A. The meeting was set up with a VIP Mode and the Austin room was configured as the VIP room. This willcause the meeting to fail until the Austin Room rejoins the conference.Build Your DreamsPassGuide 642-185

B. The meeting was set up with Austin as the Host room. This will cause the meeting to fail until the Austinroom rejoins the conference.

C. The Cisco TelePresence Multipoint Switch unit is failing to create any multipoint meetings and the issue hasnothing to do with the Austin room dropping the call.

D. The Cisco TelePresence Multipoint Switch has insufficient resources to host this meeting.The administrator must log into the Cisco TelePresence Multipoint Switch and assign additional segmentsto the Adhoc resources.



QUESTION 47You place a phone call from ext1234 to ext 2010. Which inbound dial peer on TEST-CMERouter 1 will bematched?

A. None, the call will dropB. default dial peer 30C. voip dial peer 30D. default dial peer



QUESTION 48When performing the Auto White Balance Adjustment on a Cisco TelePresence 3000, which three statementsare correct? (Choose three.)

A. Lights must be set as they would be during a Cisco TelePresence meeting.B. The RJ-45 cables must be unplugged from the cameras not being configured to ensure that each camera is

set up independently.C. Ensure that no movement in the room might cross in front of the camera or create shadows on the target

board.D. Target boards should be set up on each table segment at the same time. The adjustment Build Your

DreamsPassGuide 642-185runs on all segments at the same time to capture the exact lighting for a consistent configuration.

E. The adjustment must be run on eachsegment and can be run only one segment at a time.F. The adjustment needs to be run only on the center camera. The settings are duplicated on the left and right

segments.

Correct Answer: ACESection: (none)Explanation


QUESTION 49When using HFR codec in a multipoint call, what happens when an endpoint without HFR calls in?

A. The entire call downgrades the data channel to 5 fps.B. The entire call downgrades the data channel to 5 fps but when the endpoint without HFR codec drops, it

automatically increases the data channel to 30 fps.C. The endpoint without the HFR shares data at 5 fps and all the other endpoints share at 30 fps.D. The call drops since there are different frame rates.




Identify the port number where the A/V expansion box should connect.

A. 4B. 5C. 6


D. 7E. 9F. 10G. 11H. 12I. 13

Correct Answer: HSection: (none)Explanation


QUESTION 51Which statement about the Cisco Unified Communications Manager Express configuration is correct based onthe following information?

A. Nothing needs to be added. MoH will work fineB. MoH will not work because the multicast address is incorrectC. MoH will not work because you need to add the route 10.3.130.1 command in multicast moh 239.1.1.1 port

2000.D. The configuration will work only for calls that are being transferred because the transfer-system command

has been added.



QUESTION 52Refer to the exhibit. When a Cisco IP Communicator Phone roams from the San Jose site to the RTP site, thePhysical Location for the Cisco IP Communicator Phone changes and the Device Mobility Group remains thesame. After roaming to RTP, the user called a colleague in RTP and conferenced in a phone in his homelocation (San Jose). Which statement about the MRGL for the Cisco IP Communicator Phone is true?


A. The Cisco IP Communicator Phone will use the RTP_MRGL regardless of Device Mobility Group.B. The Cisco IP Communicator Phone will use the Home MRGL (SJ_ MRGL) since he is conferencing a user

at his home location.C. The Cisco IP Communicator Phone will use the Home MRGL (SJ_ MRGL) since his Device Mobility Group

(DMG) remained the same.D. The Cisco IP Communicator Phone will use the RTP_MRGL since his Device Mobility Group remained the

same.



QUESTION 53What are the three levels of room design category?

A. Basic, Standard, HighB. Good, Better, BestC. Classic, Professional, ExecutiveD. Remedial, Classic, Professional



QUESTION 54During the RRA, how should you hold the light sensor when taking the majority of light measurements?

A. Horizontally, so it gets the direct lighting from ceiling light fixtures.Build Your DreamsPassGuide 642-185

B. Vertically, toward the displays to measure the light they put off.C. Horizontally, toward and untreated windows to measure light coming in.D. Vertically, so it is reading light as if it were hitting the participant's face.



QUESTION 55Which two Cisco TelePresence systems are certified for room acoustics, lighting, continuity, network design,and system performance? (Choose two.)

A. Cisco CTS-500B. Cisco CTS-1100C. Cisco CTS-1300D. Cisco CTS-3000E. Cisco CTS-3200

Correct Answer: DESection: (none)Explanation


QUESTION 56Refer to the exhibit. Horst's Helicopters has a centralized Cisco Unified Communications Managerdeveloyment, with SRST implemented on MGCP gateways at the remotes sites. The WAN link to Seattle hasfailed. All phones in Seattle have registered to the SRST gateway and can call each other internally, but alloutside calls fail. Based on the output shown in the exhibit, what is the most likely solution to the problem?


A. Configure MCGP fallback on the gateway.B. Add the isdn outgoing-voice command to the configuration.C. Call the phone provider and report that the PRI link is down.D. Enable the outgoing POTS dial peer with the no shutdown command.



QUESTION 57Refer to the exhibit. A gatekeeper needs to be configured to provide Call Admission Control. Within the LosAngeles zone the maximum bandwidth for a single session is 128 kb/s and the maximum bandwidth betweenthe Los Angeles zone and any other zone is 256 kb/s. which two commands need to be added to theconfiguration to accomplish these requirements? (Choose two.)

A. bandwidth session 128B. bandwidth session zone la 128C. bandwidth total default 256D. bandwidth interzone la 256E. bandwidth default 128

Correct Answer: BDSection: (none)Explanation


QUESTION 58A single scanner needs to scan how many hosts belonging to the internal zone on TCP port 8081 before theanomaly detection configuration for vs1 will free an alert?

A. 3 or more hostsBuild Your DreamsPassGuide 642-185

B. 6 or more hostsC. 9 or more hostsD. 150 or more hosts



QUESTION 59Which two types of dial peers are needed to complete this call end-to-end?

A. serial dial peerB. parallel dial peerC. POTS dial peerD. VoIP dial peer

Correct Answer: CDSection: (none)Explanation


QUESTION 60On a Cisco TelePresence CLI, which command is the correct syntax to get Layer 2 addresses of all connecteddecices?

A. showarp listB. utils arp listC. getarp listD. arp lsit ativeE. showarp active



QUESTION 61Refer to the exhibit. Which two options do you need to deploy for the topology depicted to interconnect the MDS(SAN) and the Nexus 5000(LAN)?(Choose two.)


A. Fibre Channel expansion moduleB. consolidated network adapterC. Fibre Channel expansion packageD. FCoE-enabled moduleE. generation 3 line cards

Correct Answer: ACSection: (none)Explanation


QUESTION 62Refer to the exhibit. Which troubleshooting, you clear the fc1/10 interface counters and reset the interface.What the reason that interface fc1/10 is down?

A. The interface speed is missconfigured.B. The SFP is missing.C. The fiber-optic cable's transmit and receive pins are not correctly connected.D. The peer switch uses a different interoperability mode.

Correct Answer: ASection: (none)

Explanation



Which statement describes the Hard-lock VIP of a Cisco TelePresence Multipoint conference?

A. No Cisco TelePresence endpoint is allowed to join without the VIP approval..B. No Cisco TelePresence endpoint is allowed to join until the designated VIP Cisco TelePresence endpoint

joins.C. VIP video is switched out temporarily with voice-activated switching; VIP video is switched back

automatically.D. VIP video is always displayed at all sites and is never switched out



QUESTION 64What are two design considerations for corporate branding of a coustomer's Cisco TelePresence room?(Choose two.)

A. The room design is in-line with the existing look and feel of surrounding facilities.B. The room design is specific to Cisco guidelines and corporate branding is not relevant.C. The designer ensures the Cisco TelePresence installation and does noting terms of corporate brand design.D. The room design conveys corporate values.E. Corporate branding supersedes other aspects of room design.



QUESTION 65Please explain the parameter Overlay on button number 2.


A. It means that this IP phone has than one extension configured on line 2.B. It means any calls to line 1 when busy will be automatically forwarded to line 2.C. It means that the user can dial using any Overlay application, for example, Click to dial application.D. It means that the extension on line 2 is part of an Overlay group that handles calls that have been sitting in

the queue and exceed the "Lay" limit.



QUESTION 66Refer to the exhibit. The network has just been installed. Host B can access the Internet, but it is unable to pinghost C. What is the problem with this configuration?

A. Host B should be in VLAN 13B. The address of host C is incorrect.C. The gateway for host B is in a different subnet than the host is on.D. The switch port that sends VLAN 13 frames from the switch to the router is shut down.E. The switch port connected to the router is incorrectly configured as an access port.



QUESTION 67Which audio codec(s) are supported between the CTMS and CUVC 35XX?

A. G.711 and G.722B. G.722C. AAC-LDD. AAC-LD,G.711 and G.722E. G.711




QUESTION 68Your company has a Cisco TelePrensence 3200 room that is configured to get an IP address from yourcorporate DHCP server. The primary codec has received the address 10.0.200.4/24 from DHCP server. Whenthe first two secondary codecs request their IP addresses from a DHCP server, which addresses will theyreceive?

A. Both secondary codecs will be assigned the IP address 10.0.200.4/24.B. Secondary codecs are statically configured and do not request DHCP.C. Secondary codecs will receive addresses 10.0.200.5/24 and 10.0.200.6/24.D. Secondary codecs will receive addresses 192.168.0.2/24 and 192.168.1.2/24.E. Secondary codecs will receive addresses 192.168.0.1/24 and 192.168.0.2/24.



QUESTION 69What is the interval between Cisco TelePresence video frames on a point-to-point call when using apresentation codec on both endpoints?

A. 20 msB. 30 msC. 33 msD. 60 ms



QUESTION 70Refer to the exhibit. Which command would a user be able to use if given a role with this rule set?


A. clear counters interface fc1/1B. switchport speed 1000C. show FLOGI databaseD. radius-server host 10.10.0.0 auth-port 2003



QUESTION 71Refer to the exhibit. You have six IP making six conference calls. Which conference resource will Conference 4use?


A. HW_CFB_1B. HW_CFB_2C. SW_CFB_1D. SW_CFB_2E. SW_CFB_3



QUESTION 72What is the additional bandwidth consumption for the High Frame Rate codec to do 30 fps data collaboration?

A. 2 MbpsB. 4 MbpsC. 5 MbpsD. 6 Mbps



QUESTION 73Refer to the exhibit.Which action should you take to connect the Cisco MDS Switch to an existing Brocade andMcData multivendor SAN network using interoperability mode 1?


A. Reconfigure the DomainID to 100B. Change the sWWN using the McDta OUI.C. Force the principal switch election with prioritu 1.D. Disable the VSAN functionality.



QUESTION 74Refer to the exhibit. A user in RTP calls a phone in San Jose during congestion with Call Forward NoBandwidth(CFNB) configured to reach cell phone 408555150. The user in RTP sees the message "Not EnoughBandwidth" on their phone and hears a fast busy tone. Which two conditions can correct this issue? (Choosetwo.)


A. The calling phone (RTP) needs to have AAR Group value of AAR under the AAR Settings.B. The called phone (San Jose) needs to have AAR Group value of AAR under the AAR Settings.C. The calling phone (RTP) needs to have AAR destination mask of 914085550150 configured under AAR

Settings.D. The calling phone (RTP) needs to have AAR destination mask of 4085550150 configured under AAR

Settings.E. The called phone (San Jose) needs to have AAR destination mask of 914085550150 configured under AAR

Settings.F. The called phone (San Jose) needs to have AAR destination mask of 4085550150 configured under AAR

Settings.

Correct Answer: BFSection: (none)Explanation


QUESTION 75What protocol is used by the Cisco TelePresence codec to push meetings to its Cisco IP


Phone 797x?

A. AXLB. XMLC. RTCPD. RMI



QUESTION 76Which is correct when determining a background color for a Cisco TelePresence room?

A. select a bright color that draws attentionB. select white so everything stands out in front of itC. select the darkest colors so the plasmas will render other colors more accuratelyD. select neutral tones to give the appearance of warmth without too much distraction



QUESTION 77Refer to the exhibit. HostA cannot ping HostB. Assuming routing is properly configured, what could be thecause of this problem?

A. HostA is not on the same subnet as its default gateway.B. The address of SwitchA is a subnet address.C. The Fa0/0 interface on RouterA is on a subnet that can't be used.D. The serial interfaces of the routers are not on the same subnet.E. The Fa0/0 interface on RouterB is using a broadcast addresss.




QUESTION 78Refer to the exhibit. Bob has set his phone to forward calls to extension 5000. When a call is placed toextension 2000, which phone will ring?

A. Phone AB. Phone BC. Phone CD. Phone D



QUESTION 79Given the following:

Cisco TelePresence endpoint A:Phone field: Disable Speakerphone and Headset is checked. ON configuration: Auto answer is enabled.Cisco TelePresence endpoint B:Phone field: Disable Speakerphone and Headset is unchecked. ON configuration: Auto answer is enabled.What happens when Cisco TelePresence endpoint A calls Cisco TelePresence endpoint B?

A. Cisco TelePresence endpoint A gets a fast busy.B. Cisco TelePresence endpoint B gets a ring, and the call will establish as an audio-only call out of the Cisco

IP Phone.C. Cisco TelePresence endpoint B gets a ring, and the call will establish as a video-only call.D. Cisco TelePresence endpoint B gets a ring, and the call will establish , but there is no audio Build Your

DreamsPassGuide 642-185or video.



QUESTION 80Which protocol is used by the Cisco TelePresence Multipoint Switch to instruct Cisco TelePresence endpointsto stop transmitting video during an active multipoint call?

A. RTSPB. RTCPC. SIPD. H.323



QUESTION 81Refer to the graphic. Users on the Holyoke router are unable to access the intranet server attached to interfaceE0 of the Chicopee router. Inspection of the routing table of the Holyoke router shows that an entry for theChicopee E0 network is missing. Which command will configure the Holyoke router with a path to the intranetserver network?

A. Holyoke (config) # ip host Chicopee 201.73.27.2B. Holyoke (config) # ip host Chicopee 201.73.27.0.255.255.255.0C. Holyoke (config) # ip network 202.18.38.0D. Holyoke (config) # ip network 202.18.18.0. 255.255.255.0E. Holyoke (config) # ip route 202.18.18.0. 255.255.255.0.201.73.127.2F. Holyoke (config) # ip route 202.73.127.2.255.255.255.0.202.18.18.0



QUESTION 82Why has the network shown in the exhibit failed to converge?


A. The no auto-summary command needs to be applied to the routers.B. The network numbers have not been properly configured on the routers.C. The subnet masks for the network numbers have not been properly configured.D. The autonomous system number has not been properly configured.E. The bandwidth values have not been properly configured on the serial interfaces.



QUESTION 83Which option should you deploy to prevent man-in-the-middle attacks?

A. IPsecB. fabric bindingC. FC-SPD. SME

Correct Answer: A



QUESTION 84Which bandwidth is used by Cisco TelePresence CTS-1 000 for sending audio during an active call thatexcludes collaboration and audio add-in?

A. 64 kb/sB. 128 kb/sC. 192 kb/sD. 256 kb/s



QUESTION 85Which three statements correctly describe the communication between the Cisco TelePresence Manage andCisco Unified Communications Manager?

A. AXL\SOAP over HTTPS to the RIS Database of the Cisco Unified Communications Manager to obtaindetails from endpoint profiles.

B. AXL\SOAP over HTTPS to Unified CM for TelePresence Room discovery.C. AXL\SOAP over HTTPS to Unified CM for Multipoint Conferencing Unit discovery.D. CTI\QBE API used to monitor registration status of Multipoint Conferencing Unit discovery.E. CTI\QBE API used to monitor registration status of discovery TP rooms.

Correct Answer: ABESection: (none)Explanation


QUESTION 86When using Auto-Collaborate, what two actions need to be done to display the laptop content after connectingthe cable? (Choose two.)

A. Press the Auto-Collaborate softkey.B. Initiate Auto-Collaborate on the codec's GUI.C. Set the laptop resolution to 1024x768.D. Set your laptop resolution to 1024x720.E. Use function key on the laptop to send signal to external display.



QUESTION 87A Cisco TelePresence System 1000 is assigned 192.168.3.200/28. There is no LAN misconfiguration. Whywould the Cisco TelePresence System 1000 not be able to reach the CUCM?

A. The CUCM has an IP address of 10.1.1.2.B. The CUCM has an IP address of 192.168.3.2.C. The CUCM has the same MAC address as the CTS.D. There should be no issue.



QUESTION 88How much bandwidth does a Cisco CTS-3000 running at 1080p-best require with overhead and presentation(HFR) codec?

A. 11 Mb/sB. 15.4 Mb/sC. 18.3 Mb/s


D. 19.6 Mb/s



QUESTION 89What is the maximum dejitter buffer size in Cisco TelePresence endpoints?

A. 30 msB. 120 msC. 150 msD. 165 ms



QUESTION 90Which DHCP server gives secondary codecs in Cisco TelePresence CTS-3000 and CTS-3200 systems their IPaddresses?


A. DHCP server on the voice VLANB. DHCP server on the primary codecC. DHCP server on the Cisco Unified Communications ManagerD. DHCP server on the Cisco TelePresence Manager



QUESTION 91S0/0 on R1 is configured as a multipoint interface to communicate with R2 and R3 in the hub-and spoke FrameRelay topology shown in the exhibit. Originally, static route were configured between these routers tosuccessfully route traffic between the attached networks. What will need to be done in order to use RIP v2 inplace of the static routes?

A. Configure the no ip subnet-zero command on R1, R2, and R3.B. Dynamic routing protocols such as RIP v2 cannot be used across Frame Relay networks.


C. Configure the s 0/0 interface on R1 as two subinterfaces and configure point-to-point links to R2 and R3.D. Change the 172.16.2.0/25 and 172.16.2.128/25 subnetworks so that at least two bits are borrowed from the

last octet.E. Change the network address configurations to eliminate the discontigujous 172.16.2.0/25 and

172.16.2.128/25 subnetworks.



QUESTION 92On a Cisco TelePresence CLI, which command is the correct syntax to run a traceroute to a remote host?

A. network trace route {dest}B. tracert {dest}C. utils network tracert {dest}D. settracert {dest}



QUESTION 93What are the three necessary steps to configure a MIDlet? ( Choose three.)

A. Add another XML service in the CUCM and restart the tftp services.B. Upload required MIDlet files from CUCM TFTP file management and restart the tftp services.C. Add a service for MIDlet and subscribe the IP phone to that service.D. Subscribe the codec with the XML service you created for MIDletE. Configure authentication server URL in CUCM's IP phone device configuration page.

Correct Answer: BCDSection: (none)Explanation


QUESTION 94Refer to the exhibit. A call is placed from DN 5000 to DN 6999. The CSS for the call includes only the Branch 1partition. After the translation pattern is applied, what are the called and calling numbers?


A. 6999,5000B. 14085556999,5000C. 6999,1919555000D. 5556999,919555000E. 14085556999,1919555000



QUESTION 95On a Cisco TelePresence CLI, which command is the correct syntax to get the list of all services running?

A. utils service listB. service running listC. show service listD. get service list



QUESTION 96What are three reasons a CUCM cluster is recommended for Cisco TelePresence systems? (Choose three. )

A. The endpoints are able to connect faster.B. Easier to manage Cisco TelePresence systems related CUCM upgrades.C. Can prioritize Cisco TelePresence traffic separate than other video traffic.D. Some endpoints do not work with Cisco IP Phones.E. Production environment may not be running minimum CUCM version required Cisco TelePresence.F. Easier to create trunks with a dedicated CUCM cluster.

Correct Answer: BCESection: (none)Explanation


QUESTION 97As per RFC 4594, which DSCP marking should be used for Cisco TelePresence bearer traffic?

A. AF31B. AF41C. CS3D. CS4E. EF



QUESTION 98Refer to the exhibit. At the end of RSTP election process, which access layer switch port will assume thediscarding role?

A. Switch3, port fa0/1B. Switch3, port fa0/12


C. Switch4 , port fa0/11D. Switch4 , port fa0/2E. Switch3, port Gi0/1F. Switch3, port Gi0/2



QUESTION 99Your customer would like you to connect a OVI-O output to the Auto Collaborate video channel. What are yourtwo connection options? (Choose two.)

A. use a DCI-D to VGA male converterB. use DCI to HOMI cableC. use a VGA to DVI-A cableD. use a M1 to DVI-D cable



QUESTION 100The configuration for Call Park has been set. Users complain that the Call Park softkey does not appear ontheir phones. How to solve this problem?


A. You should add park-slot number ephone-dn 5B. You should restart the phones.C. You should configure park-slot number outside the range of 5xxx unmbers.D. The call-park command enable needs to be added under telephony-service.



QUESTION 101If the neighboring room produces 72 dB of noise, what would the minimum STC rating of the dividing wall needto be to block the noise?

A. 50B. 60C. 70D. 80



QUESTION 102In Release 1.5, what is the maximum amount of bandwidth used for traffic to and from the Cisco TelePresenceMultipoint Switch when all segments are used for non-interoperability calls?

A. 240 Mb/sB. 249 Mb/sC. 262 Mb/sD. 264 Mb/s



QUESTION 103You are configuring the Cisco IP Phone in the Cisco Unified Communications Manager for the CiscoTelePresecnce Room without using the Enhanced Phone User Interface (MIDlet). You must enter the URLinformation for the codec in the External Data Locations Information section. Which three fiels require a URL toallow the Cisco IP Phone to work correctly?(Choose three.)

A. InformationB. DirectoryC. MessageD. ServicesE. Authentication ServerF. Proxy Server


G. Idele

Correct Answer: DEGSection: (none)Explanation


QUESTION 104Which three states are possible within a dual-rate policer? (Choose three.)

A. conformingB. exceedingC. excess burstingD. violatingE. traffic policing

Correct Answer: ABDSection: (none)Explanation


QUESTION 105DSPs inside each Cisco TelePresence codec encode the digital video signal from the video cameras into RTPpackets using which encoding and compression standard?

A. SIPB. H.264C. H.225D. MPEGE. QCIF



QUESTION 106Given the following:Cisco TelePresence endpoint A: In the Cisco Unified Communications Manager, Quality is set to High Detail,Good Motion: 720pCisco TelePresence endpoint B In the Unified CM, Quality is set to High Detail, Best Motion:1080pWhat happens when Cisco TelePresence endpoint A calls Cisco TelePresence endpoint B?

A. Cisco TelePresence endpoint A gets a fast busy.B. The call connectsbut it drops with a Configuration mismatch error on Cisco TelePresence endpoint B.C. Cisco TelePresence endpoint B quality upgrades to 1 DSDp and the call goes through at 1 DSDp.D. Cisco TelePresence endpoint B quality drops down to 72Dp and the call goes through at 72Dp.



QUESTION 107What is an aesthetic requirement for a dedicated, three-screen Cisco TelePreasence room?

A. neutral colored wallsB. signageC. recessed, indirect lightingD. pendant lightingE. furniture that matches the Cisco TelePresence table



QUESTION 108Refer to the exhibit. What CSS should be assigned to a phone in the Phones partition to block calls tointernational numbers while allowing all other calls?

A. CSS AB. CSS BC. CSS CD. CSS D



QUESTION 109During your RRA assessment of a potential Cisco TelePresence Systen 3000 room you notice:* Walls 1, 2, and 4 are painted plasterboard (drywall)* Walls 3 is a heavy plate glass interior wall with a solid frosted finish


What are two inherent concerns? (Choose two.)

A. Privacy is compromised because people will be able to see into the room through the glass wall.B. Lighting from the adjacent room may illuminate a portion of this room and should be measured to see if

remediation is required.C. The glass wall will promote excessive reverberation between itself and the multiple plasma screens on the

Cisco TelePresence endpoint.D. The glass wall will promote excessive reverberation between itself and wall 4.



QUESTION 110Which bandwidth is used by Cisco TelePresence CTS-3000 for sending audio during an active call thatincludes collaboration and audio add-in?




QUESTION 111What two protocols can Cisco TelePresence endpoints use for Cisco Unified Video Conferencing? (Choosetwo.)

A. H.323B. SCCPC. SIPD. SRTP



QUESTION 112What two options does an administrator have using WebUI for CTMS in Monitoring/Room Testing for activemeeting? (Choose two.)

A. add a CTS System to a meetingB. view network statisticsC. view meeting statisticsD. start loopbackE. force switch


Correct Answer: ABSection: (none)Explanation


QUESTION 113Refer to the exhibit. Apart from the Cisco MDS sWWN, what do you need to change in order to be able toconnect the Cisco MDS to an existing McData switch using interoperability mode 4?

A. DomainID must be set to a value between 1 and 31.B. VSAN load balancing must be changed to the source, destination, exchange ID.C. The priority must be set to 1 to force the MDS to become the principal switch.D. VSAN 4094 must be used on an interface connected to the McData switch.





Identify the port number where the DMP audio device should connect.

A. 4B. 5C. 6D. 7E. 9F. 10G. 11H. 12I. 13



QUESTION 115Given the following:Cisco TelePresence endpoint A: CTS-3000Cisco TelePresence endpoint B: CTS-1000Cisco TelePresence endpoint C: CTS-1300Cisco TelePresence endpoint D: CTS-1000For a multipoint meeting scheduled between these endpoints, only endpoint A calls in. If this is the only meetingcurrently active, how many segments are being reserved on the Cisco TelePresence Multipoint Switch?

A. 0

B. 1C. 3D. 6E. 8



QUESTION 116You execute the show ephone command in the Cisco Unified Communications manage as below. Whatinformation will you get from the output?


A. There is only one IP phone.B. There are two registered IP phones. Shared number 5010 on line 2. Message waiting on shared line.C. There are two IP phones. Phone 2 is unregistered. Shared number 5010 on line 1. Message waiting on

shared line.D. There are two IP phones. Phone 2 is unregistered. Shared number 5010 on line 1. Message waiting on line

1 of phone 1.



QUESTION 117You configure a dial peer that points to Cisco Unity Express. Which line of configuration is incorrect?

A. TEST-BB. TEST-CC. TEST-DD. TEST-F



QUESTION 118The Centralized Component Compliance Module within the Network Path Assessment process consists ofwhich four components? (Choose four.)

A. Cisco Unified Communications Manager readinessB. Cisco TelePresence Manager readinessC. Cisco IOS Software and Catalyst operating system readinessD. Cisco Unified Videoconferencing Manager interoperability readinessE. Cisco TelePresence Multipoint Switch readinessF. Cisco security readiness

Correct Answer: ABDESection: (none)Explanation


QUESTION 119How are Cisco TelePresence Multipoint Switch resources selected for scheduled multipoint meetings?

A. The Cisco TelePresence Manager randomly selects a Cisco TelePresence Multipoint Switch to host themeeting.

B. The Cisco TelePresence Manager uses time zones to find the best Cisco TelePresence Multipoint Switchlocation for the meeting.

C. Cisco TelePresence Manager uses latitude and longitude to find nearest Cisco TelePresence Managerlocation for the meeting.

D. System administrator configures the Cisco TelePresence Manager - Cisco TelePresence System pairingsfor multipoint meetings.



QUESTION 120How many discrete call legs are needed to set up a call between the POTS phone attached to TEST-Router 1and the phone in the PSTN?

A. 3B. 4C. 6D. 7




QUESTION 121Refer to the exhibit. Company ABC uses 4-digit extensions. To call between sites, they dial the intersite accesscode `8' followed by the 3-digit site code and 4-digit extension of the phone they are trying to reach. Phone_A isin partition Branch1 with a CSS named BR1_External. If a user dials 85014532 from Phone_A, which elementof the route plan will be matched?

A. Route Pattern 8501! in the partition GatewayB. Route Pattern 8501.XXXX# in the partition GatewayC. Route Pattern 8501.XXXX in the partition GatewayD. the phone with extension 4532 in partition Branch1E. the phone with extension 4532 among the partition HQ_PhonesF. Translation Pattern 85XX in the partition Intersite

Correct Answer: FSection: (none)Explanation


QUESTION 122What is the maximum number of SRTP connections a Cisco TelePresence System 3200 endpoint will use?


A. 2B. 3C. 6D. D



QUESTION 123Refer to the exhibit. You have created a profile in the Cisco Unified Communications Manager for a newTelePresence room with the MAC address 00:19:A/04:4E:AE. You log into the Cisco TelePresence Managerand you enter the Discovery Service and select the Discover Rooms buttom. When you check the Roomslisting under the Cisco TelePresence Manager, you do not see the new room listed. You then inspect theDiscoveryMgr_auditiog file. Which is the cause of the problem?

Which three statements about the cabling of a Cisco TelePresence 3000 are true? (Choose three.)

A. All speakers connect to the primary codec.Build Your DreamsPassGuide 642-185

B. All video cameras connect to the primary codec.C. All 65 inch plasma displays connect to the primary codec.

D. Microphones connect to the corresponding codec.E. Speakers connect to the corresponding codec.F. Video cameras connect to the corresponding codec.G. Plasma displays connect to the corresponding codec.

Correct Answer: AFGSection: (none)Explanation


QUESTION 124A touch screen Cisco IP Phone 7970 or 7975 is part of a Cisco TelePresence endpoint. Which statement isNOT correct for the the Cisco IP Phone 7970 or 7975?

A. shares the same directory number with codecB. is used as an user interface for Cisco TelePresence systemC. is running SCCP loadD. can run both XML and MIDlet



QUESTION 125Refer to the exhibit. With the Mobile Connect feature configured, when the PSTN phone calls the Enterpriseuser at extension 3001, the Enterprise user's mobile phone does not ring. Which CSS is responsible forensuring that the correct partitions are accessed when calls are sent to the Enterprise user's mobile phone?

A. the gateway CSSBuild Your DreamsPassGuide 642-185

B. the Phone Device CSSC. the Remote Destination Profile CSSD. the Remote Destination Profile Rerouting CSSE. the Phone Line(DN)CSS



QUESTION 126What is the maximum dejitter buffer size in Cisco TelePresence endpoints?

A. 30 msB. 120msC. 150msD. 165ms



QUESTION 127Refer to the exhibit. While troubleshooting, you clear the fc 1/10 interface counters and reset the interface.What is the reason that interface fc 1/10 is down?

A. The interface speed is misconfigured.B. The SFP is missing.C. The fiber-optic cable's transmit and receive pins are not correctly connected.D. The peer switch uses a different interoperability mode.




QUESTION 128Which two of the following statements are correct regarding the virtual sensors configuration on the IPSsensor? (Choose two.)

A. vs1 uses inline interface-pairsB. vs1 operates inline between vlan 102 and vlan 201C. vs1 uses the ad1 anomaly detection instanceD. vs0 uses inline mode



QUESTION 129

Which would be considered the best environment to house a dedicated, three-screen Cisco TelePresencesystem?

A. a conference room in the cornet of a building with the best viewB. a conference room next to the elevator for easy accessibilityC. a conference room along an interior corridorD. an open space in the demonstration area of a briefing centerE. a large meeting room used for events



QUESTION 130Refer to the exhibit. Which step of digitizing analog signal does this represent?

A. signal sampleB. encodingC. sample quantizationD. 8-bit digital encoding




QUESTION 131What should the CRI rating be for a CTS-3000 or CTS-3200?

A. 56 wattsB. 60 wattsC. 82D. 92

E. 250 luxF. 800 lux



QUESTION 132When using the zoom ring on a CTS-1300 while adjusting the Left Camera for lift size, where should you alignthe black curved edge of the target on the display?

A. So that it touches the right red vertical bar on the display.B. So that it touches the left red vertical bar on the display.C. So that it touches the right edge of the display.D. So that it touches the left edge of the display.



QUESTION 133The following exhibit shows configs for H.323 gateway. You have been asked to implement TEHO from aremote branch office with area code 301 to the HQ office with area code 201 using Cisco UnifiedCommunications Manager. The remote office has an MGCP gateway and the HQ office has an H.323 gateway.Once the call arrives at the HQ, it should break out to the PSTN as a seven-digit local call. Which statementabout the route pattern is true?


A. router pattern should be 91201.[2-9]XXXXXX with Discard Digit as Predot and Prefix 9B. router pattern should be 91201.[2-9]XXXXXX with Discard Digit as PredotC. router pattern should be 91201.[2-9]XXXXXXD. router pattern should be 9.1201.[2-9]XXXXXX with Discard Digit as PredotE. router pattern should be 9.1201.[2-9]XXXXXX with Discard Digit as Predot and Prefix 9



QUESTION 134Cisco TelePresence Multipoint Switch Release 1.5 introduces the Multipoint Encryption security feature. Whichthree security settings does Multipoint Encryption support? (Choose three.)

A. authenticatedB. best-effortC. multimodeD. nonsecuredE. secured

Correct Answer: BDESection: (none)Explanation


QUESTION 135Refer to the exhibit. What alarm will be sent for this RMON event?


A. FCIP link failureB. Fibre Channel link downC. Fibre Channel link failureD. Fibre Channel link reestablishment



QUESTION 136Which statement is true about the VLAN Number field based on the following information?

A. Creating a new voice VLAN as long as it falls in the range 1 to 1001.

B. Creating a new voice and data VLAN as long as it falls within the range 1 to 1001C. Creating a voice VLAN as long as it falls in the range of 1 to 100D. Assigning a voice VLAN here in the range of 1 to 1001



QUESTION 137Which TCP port is used by Cisco TelePresence codecs to download firmware and configuration files?

A. 21B. 80C. 5060D. 6970E. 8080F. 8443



QUESTION 138Cisco TelePresence traffic receives the optimal service when it is provisioned with which QoS mechanism?

A. low latency queuingB. class-based weighted fair queuingC. weighted fair queuingD. strict policy queuing




What is the possible cause of the errors?


A. The Cisco TelePresence endpoint does not have a mailbox in the Calendar server.B. The Cisco TelePresence endpoint is not registered with the Cisco Unified Communications Manager.C. The room email address in the Unified CM for the Cisco TelePresence endpoint does match the email

address of the mailbox in the CalendarD. The Cisco TelePresence Manager user in the Calendar server does not have rights to the Cisco

TelePresence endpoint mailbox.



QUESTION 140How will an incoming call to 503 be routed based on this configuration?

A. Incoming call will be routed sequentially to users that belong to hunt group 1.B. The call will be routed sequentially to users that belong to hunt group 2.C. The call will be routed sequentially to users that belong to hunt group 3.D. The call will be routed sequentially to users that belong to hunt group 3 and then sequentially to hunt groups

1 and 2.



QUESTION 141Refer to the exhibit. On a router running Cisco IOS Release 12.3(14)T, an auto-attendant Tcl script is loadedand a warning message is displayed, stating that the operator parameter has not been registered. See theexhibit for an example of the error.


What must you do to continue?

A. nothing, the warning may be ignoredB. register the application with the gatekeeperC. register the application parameters with the gatekeeperD. register the application parameters with the applicationE. register the application with the Cisco Unified Communications ManagerF. register the application parameters with the Cisco Unified Communications Manager



QUESTION 142What is the burst size given Tc =20 ms, assuming R = 15.3 Mb/s, for a Cisco CTS-3000 running at 1080p-bestmotion?

A. 14,250 bytesB. 19,125 bytesC. 38,250 bytesD. 57,375 bytes



QUESTION 143When you place a call to 2000, phones 1 and 2 are paged. When you place a call to 2001 pages phones 3 and4. What command is missing so that a call to 2002 pages all phones1,2,3,4?

A. paging group 20 21B. paging group 10 20C. paging group allD. paging group 2000 2001 2002

Correct Answer: A



QUESTION 144Cisco TelePresence systems have which three advanced security features? (Choose three.)

A. SRTPB. SIP over TLSC. D-TLSD. SftpE. HTTPS



QUESTION 145What is the difference between A-Weighted and C-Weighted acoustic measurements?

A. A-Weighted is the ambient sound pressure level; C-Weighted is the calculated sound pressure level.B. A-Weighted is sound a human can hear; C-Weighted includes levels out of human hearing range.C. A-Weighted is the average dB of a certain area; C-Weighted is a single measurementD. A-Weighted is the average dB of a certain area; C-Weighted is a combined total measurement.



QUESTION 146Which three types of Cisco TelePresence endpoints support the Presentation-in-Picture feature? (Choosethree.)




QUESTION 147When integrating Cisco TelePresence Manager with Cisco Unified Communication Manager, an applicationuser configuration is required to have which four permissions? (Choose four.)

A. Standard AXL API AccessB. Standard CCM Admin UsersC. Standard CTI Enabled


D. Standard CCM End UsersE. Standard ServiceabilityF. Standard CCM Phone Administration

Correct Answer: ABCESection: (none)Explanation


QUESTION 148Choose the Gateway to the proper locations.

A. 2,3B. 2,5C. 3,5D. 1,3



QUESTION 149Which audio encoding and compression standard is used for a Cisco TelePresence call between two CiscoTelePresence endpoints?

A. G.711B. G.729C. Audio Lossless Coding


D. Advanced Audio Coding-Low Delay



QUESTION 150Which protocol is used by the Cisco TelePresence Multipoint Switch to instruct Cisco TelePresence endpointsto stop transmitting video during an active multipoint call?

A. RTSPB. RTCPC. SIPD. H.323



QUESTION 151How is VIP mode enabled for a scheduled multipoint Cisco TelePresence meeting?

A. through the Cisco IP phone interfaceB. through the WebUI on the CTMSC. through the Cisco TelePresence ManagerD. through calendar scheduling interface



QUESTION 152Which two media encryption methods are supported by Cisco TelePresence using SRTP? (Choose two.)

A. HMAC-SHA-1 auth tagsB. AES-128-ICMC. AES-128-CBCD. RSA Signatures



QUESTION 153What is the purpose of access code 9 based on the following information?


A. The access code 9 connects a caller to the operator when they press 9 on their phone keypad.B. This is a level 1 securityC. The access code 9 is the access code that internal users must use to make PSTN calls.D. he access code 9 is required when interfacing with a traditional PBX system



QUESTION 154What is the most effective way to way improve the continuity of a Cisco TelePresence room?

A. lighting fixturesB. adornmentsC. room colorD. artwork



QUESTION 155The customer's ISL links are flapping and seem to go down every few days. While troubleshooting the problem,they determine the speed of failover to the redundant path is taking too long. What is the recommendedsolution to the problem, involving turning on a feature?


A. use port trackingB. disable the flapping ISLC. use port channelD. adjust FSPF link costs



QUESTION 156Which Cisco TelePresence deployment model requires a Session Border controller?

A. Intra-CampusB. Intra-EnterpriseC. Inter- EnterpriseD. MultipointE. Multi-Cluster Cisco Unified Communications Manager



QUESTION 157

How do you calibrate the light meter from the Cisco recommended RRA tool kit?

A. Press the Auto Adjust button on the meter.B. Turn the meter on and off.C. Cover the sensor with the cap and press the zero button.D. Cover the sensor with the cap and press the Light Source button.



QUESTION 158Which command is the proper policer configuration given Tc = 20me for a Cisco CTS-1000 running at 1080p-best motion?

A. police 15300000 14250 conform-action transmit exceed-action drop


B. police 15300000 19125 conform-action transmit exceed-action dropC. police 15300000 38250 conform-action transmit exceed-action dropD. police 15300000 57375 conform-action transmit exceed-action drop



QUESTION 159Which two wall treatments does Cisco recommend for a Cisco TelePresence room? (Choose two.)

A. Use a glass wall.Build Your DreamsPassGuide 642-185

B. Place a whiteboard on the wall.C. Use flat paint with neutral color.D. Use wallpaper with neutral color.E. Use a wood paneled wall.F. Use a cinder block wall with neutral color.G. Use glossy paint with neutral color.



QUESTION 160During your RRA assessment of a potential Cisco TelePresence System 3000 room you notices.*None of the insulated walls extend up to the structural deck above the suspended ceiling tiles.*All adjacent rooms are conference rooms.The customer makes it clear that their landlord prohibits wall construction in the open plenum space above thesuspended ceiling. What are two appropriate recommendations? (Choose two.)

A. Recommend the customer doubles the layer of drywall below the plenum ceiling to achieve adequateisolation from adjacent room.

B. Recommend the customer installs white noise generator to mask the noise from adjacent rooms.C. Recommend the customer installs added insulation above the suspended ceiling tiles.D. Recommend the customer do noting but be advised of possible noise issues with the adjacent rooms so

that proper expectation is set.



QUESTION 161Which of these statements is true concerning VLAN Pairs and the GigabitEthernet0/0 interface based on thefollowing information?


A. you would need to edit the current configuration before adding another VLAN pair to interfaceGigabitEthernet0/0.

B. You would need to click the Add button and enter the appropriate information into the current configurationbefore adding another VLAN pair to interface GigabitEthernet0/0, y.

C. You cannot delete the default VLAN pairD. You cannot add another VLAN pair to interface GigabitEthernet0/0

Correct Answer: BSection: (none)

Explanation


QUESTION 162How many segments are supported by the Cisco TelePresence Multipoint Switch in Release 1.67

A. 16B. 24C. 32D. 48



QUESTION 163What feature does the High Frame Rate codec provide?

A. redundancy to the primary codecB. G.722 audio supportC. double the standard video frame rateD. 30 frame per second support on auto-collaboration video



QUESTION 164Which measurement is performed on the Acoustilyzer AL 1that filers out low frequency sound to approximatethe response of the human ear?

A. A-weighted SPLB. C- weighted SPLC. RTA SPLD. RT-60 SPL



QUESTION 165During your RRA assessment of a potential Cisco TelePresence System 3000 room you notice:


*The ceiling is 8 feet (2.4meters) high and currently illuminated with recessed parabolic light fixtures.Which lighting recommendation is the most appropriate?

enough light for the participants face and torso, so no lighting changes are required.

A. The ceiling should be raised higher than 8 feet (2.4meters ) to accommodate appropriate light fixtures foruse with TelePresence.

B. The existing fixtures are not ideal but are adequate for use with TelePresence.C. The ceiling fixtures should be replaced with recessed indirect light fixtures.D. No recommendation can be made until the lighting has been measured with a lux meter in the appropriate

zones.



QUESTION 166The network administrator of the Oregon router adds the following command to the router configuration: iproute 193.168.12.0.255.255.255.0.172.16.12.1. What are the results of adding this command? (Choose two.)

A. The command establishes a static route.B. The command invokes a dynamic routing protocol for 192.16.12.1.C. Traffic for network 192.168.12.0 is forwarded to 172.16.12.1.D. Traffic for all networks is forwarded to 172.16.12.1.E. This route is automatically propagated throughout the entire network.F. Traffic for network 172.16.12.0 is forwarded to the 192.168.12.0 network.



QUESTION 167What are the two file distribution types for a MIDlet? (Choose two.)

A. .rarB. .jarC. .javaD. .jad

E. .tarBuild Your DreamsPassGuide 642-185



QUESTION 168Using Auto Collaborate with a Cisco TelePresence endpoint, what resolution should the laptop share?

A. 800x600 60 HzB. 800x600 70 HzC. 1024X768 60 HzD. 1024X768 50 HzE. 1600X1200 60 Hz



QUESTION 169What jitter de-buffer threshold, when exceeded for 10 seconds, generates a warning message in the sysop logfor Cisco TelePresence codec Release 1.5?

A. 50 msB. 85 msC. 100 msD. 125 msE. 165 msF. 200 ms



QUESTION 170The Cisco Device Manager screen shows multiple problems in a SAN environment. Which two problems aredisplayed? (Choose two.)

A. The amount of RAM in the switch is running out.B. The amount of NVRAM in the switch is running out.C. Disk on port fc1/6 is at the limit of its receive bandwidth.D. Port iscsi2/2 is misconfigured.E. There is a problem with the CPU.



QUESTION 171During your RRA assessment of a potential Cisco TelePresence System 3000 room you notice:* When you acquire the average lux level measurements, all zones result with lux levels


between 268 and 290 on the vertical plane and between 604 and 678 on the horizontal plane. What are theexpected results once these measurements are submitted with the RRA?

A. The RRA will have a yellow status illumination bacause the vertical plane measurements are not between300-400 lux.

B. The RRA will have a yellow status illumination bacause the horizontal plane measurements are not above700 lux.

C. The RRA will have a yellow status illumination bacause the horizontal plane lighting is more than double thevalue of the vertical plane lighting.

D. The RRA will have a yellow status illumination bacause the vertical plane lighting is between 250-450 luxand horizontal plane lighting is less than 700 lux.

E. The RRA will have a yellow status illumination bacause there are no hotspots over 800 lux and no shadowsbelow 100 lux.



QUESTION 172On a Cisco TelePresence CLI, which command is the correct syntax to get the list of all services running?

A. utils service listB. service running listC. show service listD. get service list



QUESTION 173Which bandwidth is used by Cisco TelePresence CTS-1000 for sending audio during an active call thatexcludes collaboration and audio add-in?

A. 64 kb/sB. 128 kb/s

C. 192 kb/sD. 256 kb/s




Which statement is incorrect when a Cisco Telepresence System is used for contact center integration withUCCX?

A. The UCCX application user needs to monitor the status of both the codec and the phone.B. An agent can only be assigned with one CiscoTelepresence System endpoint.C. An agent cannot transfer a CiscoTelepresence call.D. A CiscoTelepresence System endpoint cannot put a call on hold to accept another one from the queue.



QUESTION 175

Refer to the exhibit. You have created a profile in the Cisco Unified Communications Manager for a newTelepresence room with the MAC address 00:19:AA:04:4E:AE. You log into the Cisco Telepresence Managerand you enter the Discovery Service and select the Discover Rooms button. When you check the Rooms listingunder the Cisco Telepresence Manager, you do not see the new room listed. You then inspect theDiscoveryMgr_audit.log file. Which is the cause of the problem?

A. The device profile for the Cisco CTS-3000 codec was set up with the incorrect CiscoTelepresence systemtype and this is causing the Cisco Telepresence Manager to ignore and delete the profile when it detects itis incorrect.

B. The device profile for the Cisco CTS-3000 codec was incomplete and this is causing the

CiscoTelepresence Manager to ignore and delete the profile when it detects it is incorrect.C. The device profile for the Cisco CTS-3000 codec was set up, but the device profile did not have a directory

number assigned to it, therefore the device is unregistered.D. You have not created an application user for the CiscoTelepresence endpoint in the Unified CM.E. You have not assigned the MAC address of thisTelepresence device to the Cisco Telepresence Manager's

application user account in the Unified CM.F. The CiscoTelepresence Manager has an existing room with the MAC address

00:19:AA:04:4E:AE. This will prevent the Cisco Telepresence Manager from saving this room Build YourDreamsPassGuide 642-185in its database.



QUESTION 176You are installing a CTS-1300 with a long straight cable. What is the minimum recommended distance forparticipant chair spacing?

A. 127 cm (50 inches)B. 91 cm (36 inches)C. 366 cm (120 inches)D. 76 cm (30 inches)E. 254 cm (100 inches)F. 112 cm (44 inches)



QUESTION 177You are installing a CTS-1300 with a long straight cable. What is the minimum recommended distance for theLCD bezel to the far edge of the table?





Refer to the exhibit. You are using Cisco Telepresence Manager and have just added a new room in the CiscoUnified Communications Manager and have made test calls successfully. You run the Discover Rooms optionunder Discovery Service successfully. You then go into the Rooms section and see the status. Which is thecause of the problem?

A. The Cisco Telepresence room Fluffy does not have an email account listed in the Unified CM. This ispreventing the Cisco Telepresence Manager from synchronizing with the email address for the CiscoTelepresence Room in the Calendar server.

B. The Cisco Telepresence room Fluffy has an email address listed in the Unified CM. The Calendar serverdoes not have an account for the email address provided by the Unified CM.

C. The Cisco Telepresence room Fluffy has an email address listed in the Unified CM. The Calendar serverhas an account for the email address provided by the Unified CM. The Cisco Telepresence Manager doesnot have proper privileges to view this account.

D. The Cisco Telepresence room Fluffy has an email address listed in the Unified CM. The Calendar serverhas an account for the email address provided by the Unified CM. The Cisco Telepresence Manager cannotauthenticate to the LDAP server and cannot log into the Calendar server to synchronize with the account.



QUESTION 179DRAG DROP


A.




A.




QUESTION 182What can be changed in the most cost-effective way with the biggest impact to improve the continuity of aCisco TelePresence room?




QUESTION 183How much recommended bandwidth-per-second provisioning does a Cisco TelePresence System 3000 that isrunning at 1080p require with the High Frame Rate codec?

A. 11 Mb/sB .15.4 Mb/s

B. 18.3 Mb/sC. 19 6 Mb/s



QUESTION 184Which are three administrative roles for the Cisco TelePresence Multipoint Switch? (Choose three)

A. Enabled/PrivilegedB. Super UserC. Conference SchedulerD. Concierge/Live DeskE. Diagnostic TechnicianF. Application User

Correct Answer: BCESection: (none)Explanation


QUESTION 185Under which condition is the Cisco MXE 5600 involved in a video call?

A. any point-to-point video callB. a video call that is placed between a Cisco TelePresence endpoint and a dissimilar video conferencing

endpointC. a video call that is placed between any two dissimilar endpoints Build Your Dreams

PassGuide 642-185D. any point-to-point or multipoint video call



QUESTION 186Video cafe that require interoperation are directly routed to a Cisco MXE 5600 by which one of the followingdevices?

A. Tandberg VCSB. Cisco IOS GatekeeperC. Cisco TelePresence ServerD. Cisco Unified Communications Manager

Correct Answer: DSection: (none)

Explanation


QUESTION 187Which protocol does the Cisco TelePresence Manager use to communicate with the Microsoft ExchangeServer 2003?

A. LDAPB. XMLC. WebDAVD. SIP



QUESTION 188During your assessment of a potential Cisco TelePresence System 3000 room you notice the following Thecustomer states that the landlord prohibits wall construction in the open plenum space that is above thesuspended ceiling. What are two appropriate recommendations? (Choose two)

A. The customer should double the layer of drywall that is below the plenum ceiling to achieve adequateisolation from adjacent rooms.

B. The customer should install a white noise generator to mask the noise from adjacent rooms.C. The customer should install added insulation above the TelePresence suspended ceiling tiles.D. The customer should do nothing but should be advised of possible noise issues with the adjacent rooms so

that the proper expectations can be set



QUESTION 189Which option does not need to be considered for room remediation?


A. color of the wallsB. lighting in the ceilingC. average sound pressure level of the roomD. pipe or duct above the ceilingE. location of the core layer switch



QUESTION 190Once a Cisco TelePresence Manager decides to schedule a multipoint meeting in a particular region and thatregion supports more than one CTMS, what is the process of selection?

A. The Cisco TelePresence Manager chooses the CTMS with the most available resources.B. The Cisco TelePresence Manager starts with the first CTMS in the list and selects the next CTMS in the list

once there is no capacity in the firstC. The Cisco TelePresence Manager selects the CTMS with highest preference in the list.D. The Cisco TelePresence Manager uses a round-robin algorithm to choose the CTMS.



QUESTION 191When you are using the HFR codec in a multipoint call that is using version 1.6 or less, what happens when anendpoint without the HFR codec calls in?

A. The entire call downgrades the data channel to 5 f/s.B. The entire call downgrades the data channel to 5 f/s but when the endpoint without the HFR codec drops, ft

automatically increases the data channel to 30 f/sC. The endpoint without the HFR codec shares data at 5 f/s and all of the other endpoints share data at 30 f/sD. The call drops because there are different frame rates.



QUESTION 192When configuring the Switching Policy on a Cisco TelePresence Multipoint Switch, which two switching optionscan, you choose? (Choose two)

A. DynamicB. RoomC. fragment-freeD. speakerE. rowF. on-demand




QUESTION 193On a Cisco TelePresence CTS-3000, where does audio for the left and right segments connect?




QUESTION 194The Cisco MXE 5600 performs which two of the following functions? (Choose two)

A. Routers video calls between Cisco TelePresence and non-TelePresence endpoints.B. Access SIP calls from the Cisco Unified Communications Manager only when the calling and called parties

have different media stream profile.C. Trans codes and enhances video that is sent over RTP between Cisco TelePresence and non-

TelePresence endpoints.D. Registers to the Cisco Unified Communication Manager over SIP trunk.



QUESTION 195Your customer would like you to connect a DVID output to the Auto Collaborate video channel. What are yourtwo connection options? (Choose two)

A. use a DVID to VGA male converterB. use DVI to HDMI cableC. use a VGA to DVIA cableD. use a M1 to DVID cable



QUESTION 196How do you check email by using a Cisco TelePresence system?

A. Use the Cisco IP phoneB. Use the One Button to Push Email featureC. Dial in to your email account

D. Install the Cisco TelePresence Content ModuleBuild Your DreamsPassGuide 642-185

E. You cannot check email with a Cisco TelePresence System


Explanation/Reference:Build Your Dreams

QUESTION 197Which bandwidth is used by Cisco TelePresence CTS-1000 for sending audio during an active call thatexcludes collaboration and audio add-in?




QUESTION 198You are installing a CTS-1300 with a long straight cable. What is the minimum recommended distance for theLCD bezel to the far edge of the table?








QUESTION 200Which option does not need to be considered for room remediation?


A. color of the wallsB. lighting in the ceilingC. average sound pressure level of the roomD. pipe or duct above the ceilingE. location of the core layer switch





















QUESTION 205How do you check email by using a Cisco TelePresence system?

A. Use the Cisco IP phoneB. Use the One Button to Push Email featureC. Dial in to your email accountD. Install the Cisco TelePresence Content Module


E. You cannot check email with a Cisco TelePresence System


Explanation/Reference:Build Your Dreams

QUESTION 206Refer to the exhibit. The customer network has blue and red VSANs redundantly connected, Path A having a 4-

ISL port channel and Path B having a 2-ISL port channel. Changes to the physical topology are not allowed forthe next six months. All the traffic now flows over Path A with congestion occurring on both VSANs at peaktimes. The blue VSAN is, on the average, generating four times the amount of data than that of the red VSAN.How can the blue and red VSAN traffic be spearted over the two paths, while preserving redundancy?


A. Make a zone in the blue VSAN with only ISL ports on Path B, and make another zone in the red VSAN withonly ISL ports on Path A.

B. Make a zone in the blue VSAN with only ISL ports on Path A, and make another zone in the red VSAN withonly ISL ports on Path B.

C. In the blue VSAN, give Path B a lower FSPF cost than Path A; in the red VSAN, give Path A a lower FSPFcost than Path B.

D. In the blue VSAN, give Path A a lower FSPF cost than Path B; in the red VSAN, give Path B a lower FSPFcost than Path A.



QUESTION 207Refering to the configuration for vs1. the 172.26.26.51 host OS fingerprinting is manually configured as whichoperating system type?

A. LINUXB. AIX

C. SOLARISD. WINDOWS







QUESTION 209Refer to the exhibit. Which command would a user be able to use if given a role with this rule set?


A. clear counters interface fc1/1B. switchport speed 1000C. show FLOGI databaseD. radius-server host 10.10.0.0 auth-port 2003



QUESTION 210What protocol is used by the Cisco TelePresence codec to push meetings to its Cisco IP


Phone 797x?

A. AXLB. XMLC. RTCP

D. RMI



QUESTION 211On a Cisco TelePresence CLI, which command is the correct syntax to run a traceroute to a remote host?

A. network trace route {dest}B. tracert {dest}C. utils network tracert {dest}D. settracert {dest}



QUESTION 212As per RFC 4594, which DSCP marking should be used for Cisco TelePresence bearer traffic?

A. AF31B. AF41C. CS3D. CS4E. EF



QUESTION 213What is the maximum number of SRTP connections a Cisco TelePresence System 3200 endpoint will use?


A. 2B. 3C. 6D. D



QUESTION 214Which two of the following statements are correct regarding the virtual sensors configuration on the IPSsensor? (Choose two.)

A. vs1 uses inline interface-pairsB. vs1 operates inline between vlan 102 and vlan 201C. vs1 uses the ad1 anomaly detection instanceD. vs0 uses inline mode



QUESTION 215Which three types of Cisco TelePresence endpoints support the Presentation-in-Picture feature? (Choosethree.)




QUESTION 216Choose the Gateway to the proper locations.

A. 2,3B. 2,5C. 3,5D. 1,3



QUESTION 217What is the purpose of access code 9 based on the following information?


A. The access code 9 connects a caller to the operator when they press 9 on their phone keypad.B. This is a level 1 securityC. The access code 9 is the access code that internal users must use to make PSTN calls.D. he access code 9 is required when interfacing with a traditional PBX system



QUESTION 218How do you calibrate the light meter from the Cisco recommended RRA tool kit?

A. Press the Auto Adjust button on the meter.B. Turn the meter on and off.C. Cover the sensor with the cap and press the zero button.D. Cover the sensor with the cap and press the Light Source button.



QUESTION 219Which of these statements is true concerning VLAN Pairs and the GigabitEthernet0/0 interface based on thefollowing information?


A. you would need to edit the current configuration before adding another VLAN pair to interfaceGigabitEthernet0/0.

B. You would need to click the Add button and enter the appropriate information into the current configurationbefore adding another VLAN pair to interface GigabitEthernet0/0, y.

C. You cannot delete the default VLAN pairD. You cannot add another VLAN pair to interface GigabitEthernet0/0







QUESTION 221Once a Cisco TelePresence Manager decides to schedule a multipoint meeting in a particular region and thatregion supports more than one CTMS, what is the process of selection?

A. The Cisco TelePresence Manager chooses the CTMS with the most available resources.

B. The Cisco TelePresence Manager starts with the first CTMS in the list and selects the next CTMS in the listonce there is no capacity in the first

C. The Cisco TelePresence Manager selects the CTMS with highest preference in the list.D. The Cisco TelePresence Manager uses a round-robin algorithm to choose the CTMS.



QUESTION 222Your customer would like you to connect a DVID output to the Auto Collaborate video channel. What are yourtwo connection options? (Choose two)

A. use a DVID to VGA male converterB. use DVI to HDMI cableC. use a VGA to DVIA cableD. use a M1 to DVID cable











QUESTION 225What are the three levels of room design category?

A. Basic, Standard, HighB. Good, Better, BestC. Classic, Professional, ExecutiveD. Remedial, Classic, Professional












prepking - gratis exam · prepking number : 642-185 passing ... b. configuring midlet for cts in...

Documents