product catalogue - flexfield | memoteknik

1HEXATRONIC.SERev. 2017-A

PRODUCT CATALOGUE

3HEXATRONIC.SE

ContentsTHE FLEXFIELD CONCEPT .............................................. 4

RACKS AND SUBRACKS .................................................. 6

DDF MODULES AND ACCESSORIES ............................... 8

ETHERNET MODULES AND ACCESSORIES ................... 16

ODF MODULES AND ACCESSORIES ............................. 18

4 HEXATRONIC.SE

WIDE VARIETY OF CABLES AND CONNECTORSThe module is the basic unit. There are modules to handle a variety of cables and connectors.

The FlexField Concept

A LOW COST MIX OF MODULES FOR SMALL OR BIG INSTALLATIONS Modules are hosted in the subrack, with five sizes of subracks available.

Different types of modules for different connectors/cables can be mounted in the same subrack. Start with the number of modules needed to partly fill the subrack and then add modules as needed.

FlexField – the most flexible cross connection system

• Handles coax, pair and opto cables.• Meets telecom standard G.703.• Handles data – Ethernet Cat 6.• Built on modules – fits small as well as big systems.

5HEXATRONIC.SE

19” AND ETSI RACKS/CABINETS – ALL TYPESThe subracks have mounting ears adjustable in width and depth.

SAFE MAINTENANCE AND QUICK ACCESSThere is no stress on the connectors when moving the modules, as the cables are mechanically fixed to the modules.

PATCH CORDS ARE WELL PROTECTEDPatch cords are strictly managed and well protected. The patch cords from each module enter through their own slot into the cable shelf. The cable shelf has a foldable front, which allows quick access.

PROBLEM-FREE ACCESS TO ALL CONNECTORS, WITH CABINETS TO THE WALL Due to the patented cable management in the module there is always access to all connections.

The cable management creates a built in cable slack that allows the module to always be extracted a

minimum of 30 cm from it’s original position – even at full installation. The fiber optic modules have

additional movement – they can be extracted 1.5 m. All terminations are accessible from the front.

This means that the cabinets can be placed tightly side by side to a wall.

6 HEXATRONIC.SE

Racks & Subracks

HIGH DENSITY, SERVICE FRIENDLY PATCH CORD MANAGEMENT

Racks• Designed for large amounts of patch cords.

• Patch cord crossing between racks is possible at the top. No need for threading patch cords. All passages are open. Bending radius min. 30 mm is guaranteed.

• At the top of the rack there is a built in cable duct. This replaces the overhead mounted cable duct.

• The rack has surface treatment with very good electrical conductivity.

• The rack has a grounding rail for 10 connections.

Subracks• The subrack comes in 5 sizes. Number of modules

1–10 pcs, height 1–5u.

• All subracks give front access to all connection points, which makes this system service friendly.

FlexField Rack 2000Part no. 5211

Rack with 19” profiles.

Height 2050, width 600, depth 400.

Inside height 42u.

Cable management handles up to 4000 patch cords.

No need for threading patch cords. All passages ore open. Bending radius min. 30 mm is guaranteed.

Surface treatment with very good electrical conductivity. Grounding rail for 10 connections.

When 2 racks are positioned side by side with center distance 800 mm there will be a storage for patch cord overlength. This can handle up to 4 meters overlength.

7HEXATRONIC.SE

FlexField Subrack 200Part no. 5087/20

Capacity 10 modules.

Fits in ETSI and 19” rack/cabinet.

Adjustable mounting ears.

Distance front – rack mounting point 30 alt. 80 mm.

Dimensions HxD 199(5u) x 270 mm.

Signing strip.

FlexField Subrack 45Part no. 5087/13

Capacity 2 modules.





Signing strip.

FlexField Wall Mount BoxPart no. 5087/30

Capacity 1 module.

Dimensions HxWxD: 190x130x45 mm.

FlexField Subrack 133Part no. 5263

Capacity 10 modules.





Possibility to use bending radius limiter.

8 HEXATRONIC.SE

DDF Modules & Accessories

HIGH PACKING DENSITY, SERVICE FRIENDLYHigh packing density is easily met. More than 400 coax systems or more than 800 pair cable systems can be installed in one rack/cabinet. Still all connections will be accesible and cross connection work can easily be performed.

Transmission Requirements – G.703All signals pass through multi-layer impedance controlled PCB’s and connectors of correct imped-ance. This gives good signal integrity and the trans-mission requirements in G.703 are met. The SWR budget of your link will not be ruined by FlexField.

EMCAll PCB’s have signal at the inner layers and shielding at the outer layers. The cable shields are terminated at low impedance. This result in low emission and high immuni-ty. EMC-standards like directives 89/336/EEC, 92/331 EEC are fulfilled.

Surge PulseIn some telecom applications there is a 500V surge pulse requirement. All FlexField modules fulfill this. They are tested according to IEC 61000-4-5.

9HEXATRONIC.SE

FlexField Module RJ - IDCPart no. 5100/01

Pair cable, 2 Mbit/s, E1/T1/J1.

8 systems.

Front: RJ45/48.

Inside: IDC termination, 16 pair.

Conductor: 0.4–0.63 mm.

Isolation: 0.7–1.1 mm.

Low impedance termination of shield.

FlexField Module RJ - IDC MonitorPart no. 5100/27


4 systems with monitor ports.

Front: RJ45/48, RJ45/48 25dB monitor ports.





FlexField Module RJ - RJ MonitorPart no. 5100/26



Front: RJ45/48, RJ45/48 25dB monitor ports.

Inside: RJ45/48.

FlexField Module RJ - RJPart no. 5100/02


8 systems.

Front: RJ45/48.

Inside: RJ45/48.

10 HEXATRONIC.SE

FlexField Module IDC - IDCPart no. 5100/15


8 systems.

IDC termintion, 16+16 pair.




FlexField G.703 Pair Cable Monitor CablePart no. 3408/P100/K100

Suitable for modules 5100/26, 5100/27.

To be used when the test instrument has BNC 75Ω interface.

Length 2 m.

FlexField Module 1,6/5,6 - 1,6/5,6Part no. 5100/04

Coax 75Ω 2–155 Mbit/s, E1/T1/J1/E3/T3/J3/STM-1.

4 systems.

Front: 1.6/5.6 Jack.

Inside: 1.6/5.6 Jack.

FlexField G.703 Coax Monitor CablePart no. 3102/200

Suitable for modules 5100/09, 5100/31, 5100/32, 5100/40, 5100/41, 5100/43.

To be used when the test instrument has BNC 75Ω interface.

Length 2 m.

11HEXATRONIC.SE

FlexField Module 1.6/5.6 - 1.6/5.6 MonitorPart no. 5100/31



Front: 1.6/5.6 Jack, M4 Jack 25dB monitor ports.


FlexField Module M4 - M4Part no. 5100/06


4 systems.

Front: M4 Jack.

Inside: M4 Jack.

FlexField Module BNC - BNCPart no. 5100/08

Coax 75Ω 2–270 Mbit/s, E1/T1/J1/E3/T3/J3/STM-1/video.

4 systems.

Front: BNC Jack.

Inside: BNC Jack.

FlexField Module M4 - M4 MonitorPart no. 5100/32



Front: M4 Jack, M4 Jack 25dB monitor ports.

Inside: M4 Jack.

12 HEXATRONIC.SE

FlexField Module BNC - BNC MonitorPart no. 5100/09

Coax 75Ω 2–270 Mbit/s, E1/T1/J1/E3/T3/J3/STM-1/video.


Front: BNC Jack, M4 Jack 25dB monitor ports.

Inside: BNC Jack.

FlexField Module 1.0/2.3 - 1.0/2.3Part no. 5100/34


4 systems.



FlexField Module BT43 - BT43 (SMB 75Ω)Part no. 5100/42


4 systems.

Front: BT43 Jack.

Inside: BT43 Jack.

FlexField Module 1.0/2.3 - 1.0/2.3 MonitorPart no. 5100/35



Front: 1.0/2.3 Jack, M4 Jack 25 dB monitor ports.


13HEXATRONIC.SE

FlexField Module BT43 - BT43 Monitor (SMB 75Ω)Part no. 5100/43



Front: BT43 Jack, M4 Jack 25dB monitor ports.

Inside: BT43 Jack.

FlexField Module 1.6/5.6 - IDC BalunPart no. 5100/10

Pair cable – coax 75Ω 2 Mbit/s, E1/T1/J1.

4 systems.






FlexField Module M4 - IDC BalunPart no. 5100/11


4 systems.

Front: M4 Jack.





FlexField Module 1.6/5.6 - IDC Balun MonitorPart no. 5100/41


4 systems.

Front: 1.6/5.6 Jack, M4 Jack 25 dB monitor ports.





14 HEXATRONIC.SE

FlexField Module M4 - IDC Balun MonitorPart no. 5100/40


4 systems.

Front: M4 Jack, M4 Jack 25 dB monitor ports.





FlexField Module BNC - IDC BalunPart no. 5100/12


4 systems.

Front: BNC – Jack.





FlexField Module RJ - BNC BalunPart no. 5100/24


4 systems.

Front: RJ45/48.

Inside: BNC Jack.

FlexField Module RJ - M4 BalunPart no. 5100/23


4 systems.

Front: RJ45/48.

Inside: M4 Jack.

15HEXATRONIC.SE

FlexField Module RJ - 1,6/5,6 BalunPart no. 5100/25


4 systems.

Front: RJ45/48.

Inside: 1,6/5,6 Jack.

16 HEXATRONIC.SE

Ethernet Modules & Accessories

THE PATCH PANELHigh density performance, more than 800 systems in a standard rack. Yet service friendly, the patch cords are strictly organized and all connections will be accesible so cross- connection work can easily be performed. Choose between modules for Cat5e or Cat6, STP or UTP.

You may also terminate the fiber optic riser cable and the PABX in the same patch panel. For fiber optics see section ODF.

The work area outlet8 RJ45 for 1–4 workplaces. Choose between modules for Cat5e or Cat6, STP or UTP.

DC-current in cable shieldIn an STP cabling there is always risk for unwanted DC-current in the shield due to varying ground potentials in the building. This causes a current to flow in the cable shields and this may give lower capacity in your network. To avoid this there is a module with built in dc-barrier, 5100/17.

FlexField Module RJ - RJ Ethernet STP/UTP Cat5ePart no. 5100/02

Ethernet 10/100 shielded and unshielded twisted pair.

8 systems.

Front: RJ45.

Inside: RJ45.

FlexField Module RJ - IDC Ethernet STP/UTP Cat5ePart no. 5100/16

Ethernet 10/100 shielded and unshielded twisted pair.

8 systems.

Front: RJ45.

Inside: IDC termination.



17HEXATRONIC.SE

FlexField Module RJ - JDC Ethernet UTP Cat6Part no. 5100/38

Ethernet 10/100 Gigabit ethernet unshielded twisted pair.

6 systems.

Front: RJ45.



Isolation: max 1.27 mm.

FlexField Module RJ - IDC Ethernet STP Cat6Part no. 5100/39

Ethernet 10/100 Gigabit ethernet shielded twisted pair.

6 systems.

Front: RJ45.



Isolation: max 1.27 mm.

FlexField Module RJ - IDC Ethernet UTP Cat3Part no. 5100/36

Telephone signals 64 kbit/s.

For termination of PABX.

Unshielded twisted pair.

10 lines.

Front: RJ45.




FlexField Module RJ - IDC Ethernet STP Cat6 with DC-barrierPart no. 5100/17

Equipped with DC-barrier – to stop flow of DC-current in cable shields. EMC safe design.

Ethernet 10/100/Gigabit ethernet shielded twisted pair.

4 systems.

Front: RJ45.



Isolation: 0.7 –1.1 mm.

18 HEXATRONIC.SE

ODF Modules & Accessories

ODF FOR TRUNK NETWORKS, FIBER TO THE X, LANThanks to its modular design FlexField makes an ODF for a variety of applications.

The FlexField fiber optic module handles 12 fibers. It holds splices, both single fiber and ribbon fiber and it holds fan-outs. Break-out cable and micro ducts also fit. Versions with SC adapters and FC adapters are available.

An ODF from twelve to thousands of fibers can be built.

SplicingSplices of various sizes are accepted. Defined positions give good overview. Minimum bending radius is guaranteed.

19HEXATRONIC.SE

CleaningThe front with the adapters can be pulled out. This makes it possible to clean the inner connectors.

Service FriendlyThe fibers enter the module through a flexible tube. This is of length 1.5 meter.

This gives the benefit that the splicing work can be done with the module conviniently placed on a working bench, out of the cabinet. When inserting the module in the cabinet, the flexible tube is rolled up and stored in the module.

Break Out CableThere is also a module for cables without splices and having low bending radius – being able to be brought directly into the module: break out cable; patch cord cable. No joint is used.

JointThe cable is coupled to the flexible tube by a joint.

To the left is shown Joint 48, handling a cable with maximum 48 fibers.

20 HEXATRONIC.SE

FlexField Module Break Out SCPart no. 5100/136

For cables with connectors: break out cable; patch cord cables.

Cable bending radius maximum 45 mm.

12 fibers.

SC adapters of SM quality, 6x2.

FlexField Module Splicing SCPart no. 5100/296

For splicing of ribbon fiber or single fiber. Length of splice maximum 45 mm.

12 fibers.

The cable is connected to this module using joint 48.


FlexField Module Break Out FC/PCPart no. 5100/37

For cables without splices and having low bending radius – being able to be brought directly into the module: break out cable; patch cord cable.

8 fibers.

FC/PC adapters of SM quality, 8x1.

FlexField Module splicing SC, PreconnectedPart no. 5100/306

For splicing of ribbon fiber or single fiber. Length of splice maximum 45 mm.

Preconnected with 12 pcs of pigtails, SM 10/125 UPC.

12 fibers.

The cable is connected to this module using joint 48.


21HEXATRONIC.SE

FlexField Pigtail SM 10/125 SC/UPCPart no. 4P021000/01/0100

Single fiber 10/125. Length 1 m. Diameter 0.9 mm.

Connector SC UPC.

FlexField Pigtail MM 50/125 SCPart no. 4P101000/01/0100

Single fiber 50/125. Length 1 m. Diameter 0.9 mm.

Connector SC.

FlexField Module Patch Cord Storage ShelfPart no. 5100/14

Storage of patch cord overlength.

12x5 m 2 mm cable can be stored.

Occupies the space of 2 modules in the sub rack.

Dimension W 80 mm.

FlexField Pigtail MM 62.5/125 SCPart no. 4P201000/01/0100

Single fiber 62.5/125. Length 1 m. Diameter 0.9 mm.

Connector SC.

22 HEXATRONIC.SE

FlexField Module Patch Cord Storage BobbinPart no. 5100/19

Storage of excess patch cord.

12x3 m 2 mm cable can be stored.

Occupies the space of 1 module in the subrack.

Dimension W 40 mm.

Bending radius min 30 is mechanically controlled.

Bending Radius Limiter 1uPart no. 5238

1 pair.

Fits in subrack 45-3.

Dimensions H 45 mm (1u).

Can be mounted and unmounted with subrack mounted in the rack.

Protects patch cords from sharp bending.

Quick mounting.

FlexField Joint 48Part no. 5195

For joining a cable containing maximum 48 fibers to maximum 4 Modules 5100/296 or 5100/306.

Bending Radius Limiter 2uPart no. 5239

1 pair.

Fits in subrack 133.

Dimensions H 88 mm (2u).

Can be mounted and unmounted with subrack mounted in the rack.

Protects patch cords from sharp bending.

Quick mounting.

Hexatronic Network Solutions, Sofierogatan 3A, SE-412 51 Göteborg, SwedenTel +46 (0)31 742 53 30 [email protected] www.hexatronic.se

Hexatronic Network SolutionsHexatronic Network Solutions is a Swedish based company which focuses on high quality products and solutions within four business areas: Connecting Hardware, Active Networks, Industry and Fiber Optics.

With a wealth of experience, extensive knowledge and a great interest in our customers, we develop and manufacture products and solutions with the goal of helping our clients to become more competitive. Our corporate headquarters is in Gothenburg and we have offices in Skellefteå and Stockholm.

A part of Hexatronic Group Hexatronic Group specializes in product and system solutions primarily within fiber communications. The Group offers a broad range of products and system solutions with a focus on infrastructure for passive fiber optics. Hexatronic has the stability and resources of a large Group, combined with the flexibility and speed of a small company.

Hexatronic is based in Sweden, but operates in a global market. Our customers are companies in the telecommunications industry, such as telecom operators, network owners, distributors and systems integrators. The Groups headquarters are in Sweden with sales offices and subsidiaries in Sweden, Norway, Finland, China, Great Britain, New Zealand and the United States. The Hexatronic share is listed on Nasdaq Stockholm.

For more information about Hexatronic Group: www.hexatronicgroup.com

linkedin.hexatronicpartners.se twitter.hexatronicpartners.se youtube.hexatronicpartners.se issuu.hexatronicpartners.se facebook.com/hexatronic

mailto:info%40hexatronic.se?subject=

http://www.hexatronic.se

http://linkedin.hexatronicpartners.se

http://twitter.hexatronicpartners.se

http://youtube.hexatronicpartners.se

http://issuu.hexatronicpartners.se

http://facebook.com/hexatronic

product catalogue - flexfield | memoteknik

Documents

number of modules

ethernet modules

mix of modules

ddf modules

odf modules

threading patch cords

fiber optic modules

different typesof modules