product: panoramic units - mainboard technical...

1 rev. 11/05/2015

TECHNICAL INSTRUCTIONS

Product:

Code - 97660604PANORAMIC UNITS - MAINBOARD

GB

DIAGNOSTIC LEDSCAN LED COLOR NORMAL STATE DESCRIPTION

DL11 Green ON CAN bus power supply on.

LAN LED GROUP COLOR NORMAL STATE DESCRIPTION

On K5 Green ONLAN booted on the card. Connection type. On: connection to 100Mbps. Off: connection to 10Mbps.

On K5 Yellow FLASHING

LAN booted on the card (depending on traffic). Activity network adapter. Fixed: cable connected, no activity. Flashing: Transmitting. Off: disconnected cable.

GROUP OF POWER SUPPLY

LEDSCOLOR NORMAL STATE DESCRIPTION

DL1 Green ON 12 V power supply present.DL2 Green ON 5 V power supply present.DL3 Green ON 3.3 V power supply present.DL4 Green ON 1.8 V power supply present.DL5 Green ON 1.2 V power supply present.

2 rev. 11/05/2015


Product:


GB

FPGA LED GROUPLED COLOR NORMAL STATE DESCRIPTIONDL8 Green OFF ---

DL9 Green FLASHINGFPGA loaded and clock (80 ms) ON -Note: it comes on approximately one minuteafter hyperion is turned on.

DL10 Green FLASHINGFPGA loaded and clock (80 ms) ON -Note: it comes on approximately one minuteafter hyperion is turned on; contrary to DL9.

LVDS LED GROUPLED COLOR NORMAL STATE DESCRIPTION

DL12 Green OFF

Communication in progress in channel LVDSPAN.The LED comes on (steady) while a PAN imageis acquired.

DL13 Green OFF

Communication in progress in channel LVDSCEPH.The LED lights up (steady) while a CEPH imageis acquired.

3 rev. 11/05/2015


Product:


GB

MAINBOARD LAYOUT

4 rev. 11/05/2015


Product:


GB

CONNECTIONS ON MAINBOARDCONNECTOR DESCRIPTION

K1 Temples rest.K2 Axis X motor (translation).K3 Axis Y motor (translation).K4 Axis R motor (rotation).K5 LAN network – input from POWER board.K7 Axis X photocell (translation).K9 Axis Y photocell (translation).

K12 Column potentiometer.K13 NOT USED.K14 Axis R photocell (rotation).K15 LVDS data – NOT USED.K16 LVDS data – towards PAN sensor module.K22 48V power supply – from CONVERTER board.K23 48V power supply (distribution) – NOT USED.K24 NOT USED.K35 Column motor control.K36 Upper (pin 1, 2) and lower (pin 4, 5) column limit switch (NC).

KCB1 CAN – from power board.KCB2 CAN – from converter board.KCB3 CAN – NOT USED.KCB4 CAN – NOT USED.

5 rev. 11/05/2015


Product:


GB

Backing up the setup data.

Make sure the PC-Driver is running. If the driver is running the Panoramic icon will be present in the notice area.

To backup the data, activate the service panel. Click the right key on the driver icon and select Config → PC Driver.

REPLACING THE MAINBOARD

Prerequisites for replacing the main board.

Before starting any replacement operation, make sure the following is available:• Calibration data backup (see instructions below).• Calibration kit (aluminium filter, test phantom and laser guide) to check for proper calibration after the replacement has

been made (see technical manual).• The latest version of PC-Driver (available for download on Extranet).

6 rev. 11/05/2015


Product:


GB

Press “Avanzato” (advanced) and enter password “cefla” on the driver setup panel.

Tap “Abilita mod. di servizio” (Enable service mod.) and “Salva” (Save) to enable the service panel.

7 rev. 11/05/2015


Product:


GB

Double click the Panoramic icon to go to the control panel. Click “Servizio” (Service) and press key “Backup”.

The following window for saving the data will appear. Save the file in a safe location known on the local computer. It is necessary to access this file after the board has been replaced. Make sure the folder in which the file is saved can be accessed later on. Do not use USB pen drives or other removable storage devices.

8 rev. 11/05/2015


Product:


GB

REPLACING THE BOARD

The figure below illustrates the position of the mainboard.

Loosen the screws shown in the figure and remove the cover.

MAINBOARD

9 rev. 11/05/2015


Product:


GB

Loosen the screws shown in the figure below and take off the side cover.

The mainboard can now be easily reached and replaced. Disconnect all the connections and remove the board by loosening the four screws shown in the figure.

10 rev. 11/05/2015


Product:


GB

Put in the new board and connect the connectors. The figure below points out which connections are used and which are not. Each cable has a tag that indicates the connector associated to the board.

11 rev. 11/05/2015


Product:


GB

Restoring the setup data.

Before restoring regular operation with the Panoramic unit the setup data saved before the board was replaced have to be uploaded. Double click the Panoramic icon to go to the control panel. Press “Ripristino” (restore) in the “Gestione dati di calibrazione” (setup data management) section.

Select the file previously saved and press “Apri” (Open).

12 rev. 11/05/2015


Product:


GB

At this point, turn off the device and then turn it back on. After restarting, the machine will be connected and ready for use.

Remember to disable the service panel before leaving the installation site. Click the Panoramic icon with the right key, select “Config” → ”PC Driver”. Press “Avanzato” (advanced), enter password “cefla”, deselect “Abilita mod. di servizio” (Enable service mod.) and press “Salva” (Save) and exit.

13 rev. 11/05/2015


Product:


GB

Aligning the serial numbers

In order to set the device back to “Ready”, it is necessary to align the serial numbers.Click the right key on the PC driver icon in the notice area and select Config → PC Driver.

Click “Avanzate” (advanced) and enter password “cefla” on the setup panel.

Select flag “Abilita mod. di servizio” (Enable service mod.) and press “Salva” (Save) to enable access to the service panel.

14 rev. 11/05/2015


Product:


GB

Double click the PC DRIVER icon in the notice area and then click “Numeri di serie” (serial numbers).

The panel containing the serial numbers will appear, enter the machine‘s serial number (708xxxxx) in text box ‚System‘ and press „OK“.

You will be asked if you want to save data in the device, click “Yes”.

Restart the device. The machine will be ready for use once the start up procedure has been completed.

product: panoramic units - mainboard technical...

Documents