product reference guide - s3. · pdf fileg i n e e r i n g t h a t ... 1 6 20" 10'...
TRANSCRIPT
Cablofil/Legrand
Phone 800-658-4641
618-566-3230
Fax 618-566-3250
8319 State Route 4
Mascoutah, IL USA 62258
www.cablofil.com
Pass & Seymour/Legrand
Phone 800-611-7277
Fax 800-223-4196
P.O. Box 4822
Syracuse, NY USA 13221-4822
www.passandseymour.com
Southwire
Phone 800-444-1700
Fax 770-838-6501
One Southwire Drive
Carrollton, GA USA 30119
www.southwire.com
www.ve-plus.com
Value engineering that’s guaranteed!
PRODUCT REFERENCE GUIDE
ranteed!Value engineering that s guarengineering that’s guar
Copyright © 2007 VE Plus, Printed in U.S.A. VEP•002•7/07
Today’s market demands that you deliver quality
installations with the best products available. That’s
why these industry-leading names in the electrical
industry have joined forces to increase your produc-
tivity and profitability with the VE PlusTM program. Our
studies show that you can save up to 30% on your
next commercial installation by using MC cable
from Southwire supported by Cablofil cable tray with
PlugTail devices from Pass & Seymour/Legrand
instead of conduit and pulled wire.
We’re so sure of your cost savings,
VE PlusTM
will guarantee it.
P&S PlugTail. Proven to be the fastest,
most reliable wiring device installation
for any commercial job.
At rough-in, install the pre-stripped leads of a P&S PlugTail
connector instead of pigtails. At device installation, click in the
connector and tighten the mounting screws – done in less than
a minute.
P&S PlugTail installation is three times faster than conven-
tional device installation. With no exposed terminals, you can
power-up and test a circuit at any time once the connectors
are installed. And because PlugTail delivers dependability,
quality and easier, safer service for years to come, your
customers benefit, too.
Southwire innovations help you gain
a competitive edge on every job.
UL® listed and NEC® compliant, this innovative new Type MC
cable can be used anywhere Type MC or AC cable are permit-
ted. The difference is Southwire's patented design. MCAP,
All-Purpose MC, can speed branch circuit make-up by up to
30 percent by eliminating separate ground-wire terminations.
HCF MCAP™ - the version for health care, can increase installa-
tion productivity by eliminating the need for anti-short bushings,
the need to remove the paper covering from each conductor
and can reduce securing and supporting requirements, while
providing a 350% better ground path connection. Eliminate the
most labor-intensive and costly aspect of wiring — ground
make-up inside the box, light fixture and panel.
Alumaflex™, with triple e™ aluminum alloy, feeder size MC
cable is a more flexible, light-weight and lower cost material
option to traditional pipe and wire in conduit. Pre-assembled,
factory-tested cable with color coded conductors and oversize
grounds mean a safer, easier and faster installation without
the risk of damage to conductors from pulling into conduit.
Available sizes range from 6 AWG to 900 kcmil. Switching to
aluminum MC feeder cable can reduce total installation costs
up to 50%.
Cablofil/Legrand – the world
leader in cable tray
MCAP™ cable supported by Cablofil wire tray
creates an installation that is neat and orderly
in appearance and installs faster than traditional
MC support methods. It’s capable of supporting
large number of cables in a single pathway
and the ventilated design of Cablofil tray keeps
cables cool — so no derating of cables is
required by the NEC.
An innovative
idea from the
best brands in the business!
1wwwwww..vvee--pplluuss..ccoomm
2 Cablofil's Optimized Wire Size, Tray Patent Number - 6.138.961. wwwwww..ccaabbllooffiill..ccoommAll dimensions are nominal. 880000--665588--44664411 –– 661188--556666--33224444
3wwwwww..ccaabbllooffiill..ccoommAll dimensions are nominal. 880000--665588--44664411 –– 661188--556666--33224444
PACKAGE DEPTH WEIGHT STANDARD OTHER FINISHES
QTY. INCHES WIDTH LENGTH LBS. FINISHES AVAILABLE
CVN 50 3 – 2" 3.3' 2.6 629 050 629 053 - 629 054 941 332 934 071
CVN 100 3 – 4" 3.3' 4.6 629 100 629 103 - 629 104 941 333 934 073
CVN 150 3 – 6" 3.3' 7.3 629 150 629 153 - 629 154 941 334 934 075
CVN 200 3 – 8" 3.3' 9.3 629 200 629 203 - 629 204 941 335 934 077
CVN 300 3 – 12" 3.3' 13.2 629 300 629 303 - 926 304 941 336 934 079
CVN 450 3 – 18" 3.3' 22.5 629 450 629 453 - ** 941 338 934 083
CVN 500 3 – 20" 3.3' 28.4 629 500 629 503 - 629 504 941 339 934 085
CVN 600 3 – 24" 3.3' 33.1 629 600 629 603 - 629 604 941 340 934 087
CLIP F02 25 – – – 2.2 646 200 646 207 - 646 204 942 807 942 808
COT 30 1 1 – – 2.0 923 010 923 013 - 923 014 942 283 933 889
COT 54 1 2 – – 2.8 923 020 923 023 - 923 024 942 284 933 891
COT 105 1 4 – – 4.7 923 040 923 043 - 923 044 942 285 933 895
COT 150 1 6 – – 6.6 941 011 942 680 - ** 942 298 942 370
COT J – – – – – 923 050 - - 923 054 - -
Tray Accessories
CLIP FO2CABLOFIL COVER CLIP
CVN CABLOFIL COVER
COT 30/ COT 54DIVIDER STRIP
COT 105/ COT 150DIVIDER STRIP
COT JDIVIDER COUPLER
EZBN 1/4
CE 40 SQUARE SPLICE
WASHER
CE 25 - CE 30SQUARE SPLICE
WASHER
Splicing
EDT SPLICE PLATE
PRE-CLICK SPLICE
ED 275 UNIVERSAL SPLICE BAR
EZT 90 KIT90˚ BEND KIT
RADT 90 KITRADIUS TEE 90˚KIT
EDRNTOOL MOUNTING TOOL
EDRN FAST SPLICE
SWKSPLICE WASHER KIT
PACKAGE DEPTH WEIGHT STANDARD OTHER FINISHES
QTY. INCHES WIDTH LENGTH LBS. FINISHES AVAILABLE
EDRN 50* – – – 8.8 558 241 - 558 247 - 941 281 934 032
EDRNTOOL 1 – – – 0.2 558 260 - - - 941 283 934 035
PRECLICK 8 – – – 1.7 942 735 942 736 - 942 739 942 738 942 737
EDT 50 – – – 6.6 558 251 - - 558 254 941 282 934 034
ED 275 50 – – – 14.4 558 221 558 223 - 558 224 941 279 930 621
SWK 50 – – – 3.6 558 071 - 942 746 - - -
CE 25 50 – – – 1.0 558 011 942 459 558 013 558 014 941 274 934 022
CE 30 50 – – – 1.7 558 041 942 460 558 043 558 044 941 275 934 028
CE 40 25 – – – 2.7 558 051 942 461 558 053 558 054 941 276 934 030
EZBN 1/4 50 – – – 1.3 941 084 – – 941 059 – –
FASLOCK XL 25 – – – 1.4 558 320 - 558 327 558 324 942 821 942 822
FASLOCK S 25 – – – 1.4 558 340 - 558 347 588 344 942 869 942 870
EAC – See Accessories Section at bottom of page 4
EZT 90 KIT** 1 – – – 1.5 941 052 942 686 - 941 056 942 307 942 379
RADT 90 KIT 2 1 – – – .66 942 911 - - - - -
RADT 90 KIT 4 1 – – – .66 942 912 - - - - -
*Tool included in every bag of splices**1 Kit contains hardware for 1 tee or 2 90° bends (Consists of 2 pcs EZ T90, 10 EZ BN 1/4, 10 CE 25, 2 CE 40)
FASLOCK
Tray All trays come in 10' lengths
CCFF 5544
CCFF 3300
CCFF 110055
CCFF 115500
*Products listed as “ZF” are only available in Straight Edge Tray.
COUPFIL 1 – – 24.8" 6 559 507
CCLMP21 10 – – – 0.9 942 871
CCLMP34 10 – – – 1.4 942 872
CCLMP45 10 – – – 2.1 942 873
CCLMP52 10 – – – 3.0 942 874
CCLMP64 10 – – – 3.5 942 875
CCLMP76 10 – – – 3.9 942 876
CCLMP95 10 – – – 4.7 942 877
CCLMP108 10 – – – 5.4 942 878
GNDSB 1 – – – 0.07 942 616
GNDCL 1 – – – 0.07 942 866
HD FAS ROLLER 1 – – – 3.5 942 879
HD FAS ROLLER GNDCLGROUNDING LUG
GNDSBGROUNDING LUG
CCLMPCABLE CLAMP
COUPFIL
PACKAGE DEPTH WEIGHT STANDARD OTHER FINISHES
QTY. INCHES WIDTH LENGTH LBS. FINISHES AVAILABLE
ZF 30/50* 1 1 2" 10' 3.3 000 011 000 013 000 018 000 014 941 096 933 907
CF 30/100 1 1 4" 10' 4.5 000 021 000 023 000 028 000 024 941 097 933 925
CF 30/150 1 1 6" 10' 5.7 000 031 000 033 000 038 000 034 941 098 933 934
CF 30/200 1 1 8" 10' 7.4 000 041 000 043 000 048 000 044 941 099 933 972
CF 30/300 1 1 12" 10' 9.4 000 051 000 053 000 058 000 054 941 100 934 016
CF 54/50 1 2 2" 10' 5.3 000 061 000 063 000 068 000 064 941 101 934 056
CF 54/100 1 2 4" 10' 6.5 000 071 000 073 000 078 000 074 941 102 934 095
CF 54/150 1 2 6" 10' 7.8 000 081 000 083 000 088 000 084 941 103 934 130
CF 54/200 1 2 8" 10' 9.0 000 091 000 093 000 098 000 094 941 104 934 158
CF 54/300 1 2 12" 10' 13.4 000 101 000 103 000 108 000 104 941 105 933 901
CF 54/450 1 2 18" 10' 22.8 000 251 000 253 000 258 000 254 941 108 933 928
CF 54/500 1 2 20" 10' 24.4 000 301 000 303 000 308 000 304 944 109 933 932
CF 54/600 1 2 24" 10' 27.5 000 401 000 403 000 408 000 404 941 110 933 944
CF 105/100 1 4 4" 10' 9.0 000 891 000 893 000 898 000 894 941 114 934 146
CF 105/150 1 4 6" 10' 10.2 000 901 000 903 000 908 000 904 941 115 934 152
CF 105/200 1 4 8" 10' 13.4 000 911 000 913 000 918 000 914 941 116 934 160
CF 105/300 1 4 12" 10' 21.2 000 921 000 923 000 928 000 924 941 118 934 163
CF 105/450 1 4 18" 10' 25.9 001 931 941 071 941 072 941 073 942 463 942 462
CF 105/500 1 4 20" 10' 27.5 000 941 000 943 000 948 000 944 941 120 934 170
CF 105/600 1 4 24" 10' 30.4 001 031 001 033 001 038 001 034 941 127 933 905
CF 150/300 1 6 12" 10' 24.4 000 961 000 963 942846 000 964 941 122 934 174
CF 150/450 1 6 18" 10' 26.5 001 011 001 013 001 018 001 014 941 125 933 902
CF 150/500 1 6 20" 10' 27.8 001 021 941 078 941 079 941 080 941 126 933 903
ZF 150/600* 1 6 24" 10' 29.5 942 466 942 721 942 591 ** 942 474 942 475
5wwwwww..ccaabbllooffiill..ccoommAll dimensions are nominal. 880000--665588--44664411 –– 661188--556666--33224444
4 wwwwww..ccaabbllooffiill..ccoommAll dimensions are nominal. 880000--665588--44664411 –– 661188--556666--33224444
PACKAGE DEPTH WEIGHT STANDARD OTHER FINISHES
QTY. INCHES WIDTH LENGTH LBS. FINISHES AVAILABLE
FASP 150 1 – – 6" 0.4 014 150 014 153 - 014 154 941 153 930 012
FASP 200 1 – – 8" 0.7 014 200 014 203 - 014 204 941 154 930 014
FASP 300 1 – – 12" 0.9 014 300 014 303 - 014 304 941 155 930 016
FASP 400 1 – – 16" 1.1 014 400 014 403 - 014 404 941 156 930 018
FASP 450 1 – – 18" 1.2 014 450 014 453 - 014 454 941 157 930 020
FASP 500 1 – – 20" 1.3 014 500 014 503 - 014 504 941 158 930 022
FASP 550 1 – – 22" 1.3 014 550 014 553 - 014 554 941 159 930 024
FASP 600 1 – – 24" 1.5 014 600 014 603 - 014 604 941 160 930 026
FASP 700 1 – – 28" 1.8 014 700 014 703 - 014 704 941 162 930 028
FASP 1000 1 – – 40" 2.6 014 010 014 013 - 014 014 941 149 930 006
FASP 2000 1 – – 80" 5.3 014 020 014 023 - 014 024 941 151 930 008
FASP 3000 1 – – 120" 7.9 014 030 014 033 - 014 034 941 152 930 010
AS 50 – – – 6.6 586 020 586 023 - 586 024 941 301 930 675
PROCS 1000 1 – – 39" 2.6 002 920 002 923 - 002 924 941 140 930 088
PROCS 2000 1 – – 79" 5.1 002 930 002 933 - 002 934 941 141 930 090
PROCS 3000 1 – – 118" 8.4 002 940 002 943 - 002 944 941 142 930 092
FASC – See Wall Mounting Section on page 3
CSC – See Wall Mounting Section on page 3
CS – See Wall Mounting Section on page 3
ECLI 10 – – – 0.4 557 190 557 193 - 557 194 942 797 **
PS 400 1 – – 17.5" 1.5 002 730 002 733 - 002 734 941 133 930 076
PS 500 1 – – 21.4" 1.8 002 740 002 743 - 002 744 941 134 930 078
PS 600 1 – – 25.4" 2.1 002 750 002 753 - 002 754 941 135 930 080
EDF 300 1 – – 12" 0.7 561 310 561 313 - - 942 817 942 818
EDF 600 1 – – 24" 1.8 557 610 557 613 - - 942 815 942 816
EDF 1000 1 – – 40" 2.6 561 090 561 093 - - 942 813 942 814
EDF 2/3000 1 – – 10' 8.2 561 020 561 023 - 561 024 941 289 930 643
PFREDF 1 – – – 1.3 561 080 - - 561 084 942 761 942 762
DF 1 – – – 1.3 561 060 561 063 - 561 064 ** **
ERD 10 1 – – – 0.4 561 050 561 053 - - 942 759 942 760
Ceiling Mounting
AS TRAPEZE
HANGING CLIP
PROCS STANDARD
PROFILE
EDF RAIL
ECLI
PS L
ERD 10 BRACE PLATE
PFREDF MOUNTING BRACKET
DF ANGLE MOUNTING
BRACKET
FAS P FAS PROFILE
EACELEVATION
CHANGE HINGE
PACKAGE DEPTH WEIGHT STANDARD OTHER FINISHES
QTY. INCHES WIDTH LENGTH LBS. FINISHES AVAILABLE
EZBN 1/4 50 – – – 1.3 941 084 - - 941 059 942 308 -
EZBN 5/16 50 – – – 2.0 942 778 - - 942 779 942 780 -
EZHN 1/4 100 – – – 0.6 941 713 - - 941 067 - -
EZHN 3/8 100 – – – 0.7 941 915 - - 941 069 - -
EZHN 1/2 100 – – – 2.0 941 814 - - 941 068 - -
EZFW 1/4 100 – – – 0.5 941 511 942 687 - 941 065 942 309 942 381
EZFW 3/8 100 – – – 0.6 941 612 942 688 - 941 066 942 310 942 382
EZFW 1/2 100 – – – .15 ** - - - - -
TRP 10 – – 6' 0.7 ** - - - - -
THRD 1/4 – 20 Pitch 1 – – 6' 0.7 942 351 - - 942 471 - -
THRD 3/8 – 16 Pitch 1 – – 6' 1.8 942 353 - - 942 472 - -
THRD 1/2 – 12 Pitch 1 – – 6' 3.1 942 465 - - 942 789 - -
EZCN 1/4 100 – – – 3.0 941 094 - - 941 060 - -
EZCN 3/8 100 – – – 4.0 941 205 - - 941 061 - -
EZCN 1/2 100 – – – 5.0 942 790 - 942 791 942 792 -
SWK 50 – – – 3.5 558 071 – 942 476
CE 25 50 – – – 1.0 558 011 942 459 558 013 558 014 941 274 934 022
CE 30 50 – – – 1.7 558 041 942 460 558 043 558 044 941 275 934 028
CE 40 25 – – – 2.7 558 051 942 461 558 053 558 054 941 276 934 030
ED – See Splicing Section on page 2
EAC 20 – – – .18 - 558 403 - - - -
CA 50 – – – 2.2 801 051 - 801 057 801 054 ** **
FASLOCK – See Splicing Section on page 2
ECLI 10 – – – 0.4 557 190 557 193 - 557 194 ** **
COUPFIL 1 – – 24.8" 6 559 507
EZHN THRD
TRP
EZBN
EZFW
EZCN
SWK
CE 25
CE 30
CE 40
CA ECLI
COUPFIL
Accessories
Wall Mounting
FAS U UNIVERSAL BRACKET
CSC STANDARD C BRACKET
CS STANDARD L BRACKET
CRPUNIVERSAL WALL BRACKET
UC 50 CABLE TRAY STANDOFF
CAT 30/41SNAP-IN WALL
HANGER SUPPORT
FAS P FAS PROFILE
FAS L BRACKET
FVVERTICAL BRACKET
FAS C BRACKET
PACKAGE DEPTH WEIGHT STANDARD OTHER FINISHES
QTY. INCHES WIDTH LENGTH LBS. FINISHES AVAILABLE
FASP 150 1 – – 6" 0.4 014 150 014 153 - 014 154 941 153 930 012
FASP 200 1 – – 8" 0.7 014 200 014 203 - 014 204 941 154 930 014
FASP 300 1 – – 12" 0.9 014 300 014 303 - 014 304 941 155 930 016
FASP 400 1 – – 16" 1.1 014 400 014 403 - 014 404 941 156 930 018
FASP 450 1 – – 18" 1.2 014 450 014 453 - 014 454 941 157 930 020
FASP 500 1 – – 20" 1.3 014 500 014 503 - 014 504 941 158 930 022
FASP 550 1 – – 22" 1.3 014 550 014 553 - 014 554 941 159 930 024
FASP 600 1 – – 24" 1.5 014 600 014 603 - 014 604 941 160 930 026
FASP 700 1 – – 28" 1.8 014 700 014 703 - 014 704 941 162 930 028
FASP 1000 1 – – 40" 2.6 014 010 014 013 - 014 014 941 149 930 006
FASP 2000 1 – – 80" 5.3 014 020 014 023 - 014 024 941 151 930 008
FASP 3000 1 – – 120" 7.9 014 030 014 033 - 014 034 941 152 930 010
FASL 100 1 – 4" 7" 0.9 556 100 556 103 ** 556 104 941 257 930 523
FASL 150 1 – 6" 9" 1.0 556 110 556 113 ** 556 114 941 258 930 525
FASL 200 1 – 8" 11" 1.1 556 120 556 123 ** 556 124 941 259 930 527
FASL 300 1 – 12" 14.9" 1.4 556 130 556 133 ** 556 134 941 260 930 529
FASL 400 1 – ** 18.8" 1.8 556 140 556 143 566 144 ** ** **
FASL 450 1 – 18" 20.8" 2.1 556 150 556 153 ** 556 154 942 848 942 600
FASC 100 1 – 4" 7"* 1.4 556 300 556 303 ** 556 304 941 261 930 531
FASC 150 1 – 6" 8.9"* 1.5 556 310 556 313 ** 556 314 941 262 930 533
FASC 200 1 – 8" 10.9"* 1.7 556 320 556 323 ** 556 324 941 263 930 535
FASC 300 1 – 12" 14.9"* 1.9 556 330 556 333 ** 556 334 941 264 930 537
FASC 400 1 – ** 18.8"* 2.4 556 340 556 343 556 344 ** ** **
FASC 450 1 – 18" 20.8"* 2.8 556 350 556 353 556 354 ** 942 596 **
FASU 100 1 3.5 4" 6" 0.3 557 410 557 413 - 557 414 941 267 930 575
FASU 150 1 5.0 6" 8" 0.4 557 420 557 423 - 557 424 941 268 930 577
FASU 200 1 5.5 8" 12" 0.5 557 430 557 433 - 557 434 941 269 930 579
FASU 300 1 5.5 12" 14" 0.8 557 440 557 443 - 557 444 941 270 930 581
FASU 400 1 5.5 16" 18" 1.8 557 450 557 453 - 557 454 941 271 930 583
FASU 500 1 5.5 20" 22" 2.9 557 460 557 463 - 557 464 941 272 930 585
FASU 600 1 5.5 24" 26" 6.4 557 470 557 473 - 557 474 941 273 930 587
FV 100 1 – – 8" 0.7 586 070 586 073 - 586 074 942 805 **
EDF – See Ceiling Mounting Section on page 4
CS 100 1 – 4" 5.7" 0.4 002 700 008 703 - 002 704 941 130 930 070
CS 200 1 – 8" 9.6" 0.8 002 710 002 713 - 002 714 941 131 930 072
CS 300 1 – 12" 13.6" 1.2 002 720 002 723 - 002 724 941 132 930 074
CSC 100 1 – 4" 5.7"* 1.1 002 760 002 763 - 002 764 941 136 930 082
CSC 200 1 – 8" 9.6"* 1.4 002 770 002 773 - 002 774 941 137 930 084
CSC 300 1 – 12" 13.6"* 1.8 002 780 002 783 - 002 784 941 138 930 086
CRP 100 1 3.7 4" 4.6" 0.4 557 213 - - - - -
CRP 150 1 3.7 6" 6.5" 0.7 557 223 - - - - -
CRP 200 1 3.7 8" 8.5" 0.8 557 233 - - - - -
CRP 300 1 3.7 12" 12.4" 1.0 557 243 - - - - -
CRP 400 1 4.7 16" 16.4" 1.3 557 253 - - - - -
CRP 500 1 4.7 20" 20.4" 1.8 557 263 - - - - -
CRP 600 1 4.7 24" 24.3" 2.4 557 273 - - - - -
UC 50 1 – – – 0.1 586 040 586 043 - 586 044 941 304 930 681
CAT 30/41 1 – – – 0.1 942 720 942 799 - 942 742 942 800 942 801
C 50– See Other Mounting Section on page 5
FASP – See Other Mounting Section on page 5
*L measurement is for bottom profile.**Multiple Tray
6 wwwwww..ccaabbllooffiill..ccoommAll dimensions are nominal. 880000--665588--44664411 –– 661188--556666--33224444
7wwwwww..ppaassssaannddsseeyymmoouurr..ccoomm
PACKAGE DEPTH WEIGHT STANDARD OTHER FINISHES
QTY. INCHES WIDTH LENGTH LBS. FINISHES AVAILABLE
FASCLM KIT 2 – – – 0.2 559 280 - 559 287 559 284 - -
ETC 20 1 0.8 – – 0.2 942 819 - - - - -
ETC 30 1 1 – – 0.4 942 820 - - - - -
EZBC 1/4 1 – – – 0.8 941 063 ** - 941 057 - -
EZBC 3/8 1 – – – 0.8 941 074 ** - 941 058 - -
EZBC 1/2 1 – – – 0.8 942 847 942 847 - ** - -
C 50 1 – – – 0.2 586 130 586 133 - 586 134 941 308 930 694
SBDA 1 – – – 0.2 585 210 - - 585 124 942 950 942 951
CABLEXIT100 1 – – – 0.2 585 160 585 163 585 167 585 164 941 299 930 669
HB 2 KIT 1 – – 9.4" 0.4 942 419 942 686 - 942 943 942 319 942 391
DROP OUT KIT 1 – – 12.25" 0.9 942 895 942 897 - 942 944 942 896 942 898
CCLMP21 10 – – – 0.9 942 871
CCLMP34 10 – – – 1.4 942 872
CCLMP45 10 – – – 2.1 942 873
CCLMP52 10 – – – 3.0 942 874
CCLMP64 10 – – – 3.5 942 875
CCLMP76 10 – – – 3.9 942 876
CCLMP95 10 – – – 4.7 942 877
CCLMP108 10 – – – 5.4 942 878
MFM 100 1 – – 4" 0.2 585 140 585 143 - 585 144 941 297 930 664
MFM 150 1 – – 6" 0.2 585 150 585 153 - 585 154 941 298 930 667
CABLE LABEL CLIP* 50 – – – – 559 127
EZJB 5/16 2 – – 2.5" 2.0 942 016 942 689 - 941 070 942 311 942 383
SZMCKIT 1 – – 7" 0.2 942 445
SZMCCUTR 1 – – – 0.2 942 444
SZMCSWAG 1 – – – 0.7 942 446
FS 41 50 – – – 3.3 599 007 - - - 942 823 942 824
GNDSB 1 – – – 0.07 942 616
GNDCL 1 – – – 0.07 942 866
HD FAS ROLLER 1 – – – 3.5 942 879
*Available in Black, White, Orange, Yellow, Green, Blue, and Gray
Other Mountings
EZBC THREADED ROD HANGER
HB 2 WALL/FLOOR
TERMINATION BRACKET
DROP OUTCABLE DROP OUT
SBDCONDUIT AND BOX SUPPORT
CABLEXIT
ETCTRAY BEAM SUPPPORT
MFMMETALLIC MULTIFIX PLATE
CABLE LABEL CLIP
C 50ELECTRICAL BOX SUPPORT
HD FAS ROLLER
EZJB 5/16J-BOLT
SZMCKITSEISMIC BRACING KIT
FS 41FASTRUT CONNECTOR
GNDCLGROUNDING LUG
SZMCCUTRCABLE CUTTER
SZMCSWAG HAND SWAGER
GNDSBGROUNDING LUG
FASCLM KITBEAM CLAMP
CCLMPCABLE CLAMP
Cablofil wire cable tray is available in a variety of finishes to meet any industry need, from decorative to extreme
environments. Use this color code to help you to determine the best finish for your application and its availability.
Finishes
For a more detailed explanation of finish standards and compatibility, visit: www.cablofil.com.
CABLOFIL PRODUCT CODE:
Our part number makes it easy to
identify part type, size and finish.
Please use this code whenever ordering or
specifying any Cablofil product.
FOR TRAY
TYPE OF TRAY DEPTH IN MM WIDTH IN MM FINISH CODE
FOR SUPPORTS ANDOTHER PRODUCTS
FASU 300 PG
PRODUCT CODE SIZE IN MM FINISH CODE
CF EZ54 / 100
PG
EZ
GC
316L
304L
PE
BL
DC
Pre-Galvanized: ASTM A 653 Exterior applications: Industrial plantsContinuous Galvanization Norm NF/A 91-131 Interior applications: Commercial offices, Computer roomsBefore Fabrication
Electrozinc: ASTM B 633 Interior applications:Electrozinc plating Norm NF/EN 12-329 Commercial offices, Computer rooms
Hot Dipped Galvanized: ASTM A 123 Exterior applications:After Fabrication Norm NF/EN/ISO 14-61 Corrosive Environments
Dacromet: ASTM F 1136 Exterior applications:Zinc and Aluminum Protection Corrosive EnvironmentsEquivalent to Hot Dip Galvanization
Stainless Steel 304L ASTM A 380 Clean Rooms, Food preparation, Wash down areasNorm NF 10-088-2
Stainless Steel 316L ASTM A 380 Marine Environments: Oil rigs, Ships, Refineries, Norm NF 10-088-2 Power Plants, Waste Water, Treatment Plants, Cement
Plants, Pulp and Paper Mills
Black Painted: ASTM B 633 Exposed interior applications: Retail stores, Hospitals,Black Powder Coated Control cabling, Data centers
Custom Painted: ASTM B 633 Exposed interior applications: Schools, Casinos, Custom Color Data centers, Control cabling, HospitalsPowder Coated
SYMBOL FINISH TESTING METHOD APPLICATION
Catalog
Number Wire Length and Type
Catalog
Number Wire Length and Type
PTRA6STR 6" Stranded THHN12
PTRA6SOL 6" Solid THHN12
PTRA6STRB25 25" Stranded THHN12
PTRA6SOLB25 25" Solid THHN12
Specification Grade GFCIs (Non feed-though type)
PT1595* Duplex — Fed Spec Grade 15A 125V 5-15R
PT2095* Duplex — Fed Spec Grade 20A 125V 5-20R
PT1595NTL* LED Nightlight Combination 15A 125V 5-15R
PT2095NTL* LED Nightlight Combination 20A 125V 5-20R
PT1595TR* Tamper-Resistant 15A 125V 5-15R
PT2095TR* Tamper-Resistant 20A 125V 5-20R
Hospital Grade GFCIs (Non feed-though type)
PT1595HG* Duplex 15A 125V 5-15R
PT2095HG* Duplex 20A 125V 5-20R
PT1595HGNTL* LED Nightlight Combination 15A 125V 5-15R
PT2095HGNTL* LED Nightlight Combination 20A 125V 5-20R
PT1595HGTR* Tamper-Resistant 15A 125V 5-15R
PT2095HGTR* Tamper-Resistant 20A 125V 5-20R
Catalog Ratings NEMA
Number Description A. V. Config. No.
Specification Grade Receptacles
PT5262A* Extra Heavy-Duty 15A 125V 5-15R
PT5362A* Extra Heavy-Duty 20A 125V 5-20R
PTTR62* Extra Heavy-Duty — Tamper-Resistant 15A 125V 5-15R
PTTR63* Extra Heavy-Duty — Tamper-Resistant 20A 125V 5-20R
PT26252* Decorator 15A 125V 5-15R
PT26352* Decorator 20A 125V 5-20R
PTIG26262* Decorator — Isolated Ground 15A 125V 5-15R
PTIG26362* Decorator — Isolated Ground 20A 125V 5-20R
PT5262* Duplex — Fed Spec Grade 15A 125V 5-15R
PT5362* Duplex — Fed Spec Grade 20A 125V 5-20R
PTIG5262* Duplex — Isolated Ground 15A 125V 5-15R
PTIG5362* Duplex — Isolated Ground 20A 125V 5-20R
Hospital Grade Receptacles
PT8200* Extra Heavy-Duty 15A 125V 5-15R
PT8300* Extra Heavy-Duty 20A 125V 5-20R
PTTR62H* Extra Heavy-Duty — Tamper-Resistant 15A 125V 5-15R
PTTR63H* Extra Heavy-Duty — Tamper-Resistant 20A 125V 5-20R
PT26262HG* Decorator 15A 125V 5-15R
PT26362HG* Decorator 20A 125V 5-20R
U.S. Pat. No. 6,994,585
P&S PlugTail Right Angle Connectors
Third Party Compliance
I — Ivory
W — White
GRY — Gray
BK — Black
BL — Blue
Red — Red
LA — LightAlmond
1. Blue only available in Spec Grade
Duplex Receptacles
2. For Isolated Ground (IG) Receptacles,
no color designation = Orange
3. For all other receptacles, no color
designation = Brown
*Color Designation
cULus Listed, File Number E140596,
Standard UL498, Federal Specification
WC596
PPTTTTRR6633WW
PPTTTTRR6633HHWW
PPTTTTRR6633HHLLAA
PPTT2266335522LLAA
PPTT22009955HHGGNNTTLLLLAA
PPTT22009955LLAA
PPTT55336622AAWW
PPTT88330000WW
PPTT22009955HHGGTTRRWW
PPTTIIGG55336622
PPTT22009955TTRRLLAA
PPTT55336622LLAA
PPTT2266336622HHGGII
PPTTIIGG2266336622
Electrical Devices
8 9wwwwww..ssoouutthhwwiirree..ccoommwwwwww..ssoouutthhwwiirree..ccoomm
NUMBER OF CONDUCTORS COLOR SEQUENCECOLOR SEQUENCE
277/480Y
NUMBER OF
CONDUCTORS
CONDUCTOR
SIZE (AWG)/
# OF PHASE
CONDUCTORS
CONDUCTOR
TYPE*
GROUNDING/
BONDING
CONDUCTOR
AMPACITY (AMPS)‡
60°C
OVERALL
DIAMETER
(inches)
GREEN THHN
COPPER GROUND
(AWG)
WEIGHT
(lbs./1000 ft.)75°C 90°C
STANDARD PACKAGE
COIL (feet) REEL (feet)
500 Note: Ampacities are based on Table 310.16 of the NEC, 2005 Edition. *Circuit sizes 12 AWG and 10 AWG also available as stranded conductors.‡Allowable ampacities shown are for general use as specified by the National Electrical Code, 2005 Edition, Section 310.15. If the equipment is markedfor use at higher temperatures, the conductor ampacity shall be limited to the following per NEC 110.14(C).60°C - When terminated to equipment for circuits rated 100 amperes or less or marked for size 14 through 1 AWG conductors.75°C - When terminated to equipment for circuits rated over 100 amperes or marked for conductors larger than size 1 AWG.90°C - For ampacity derating purposes.Per NEC 310.15(B)(2)(a), the ampacity of 4/C cables shall be reduced by a factor of 0.80 when the neutral is considered a current-carrying conductor.
12 / 2 Solid 10 solid AL 12 0.445 110 20 20 20 250 1000
12 / 3 Solid 10 solid AL 12 0.480 134 20 20 20 250 1000
12 / 4 Solid 10 solid AL 12 0.515 180 20 20 20 250 1000
10 / 2 Solid 8 solid AL 10 0.520 162 30 30 30 250 1000
10 / 3 Solid 8 solid AL 10 0.565 202 30 30 30 250 1000
10 / 4 Solid 8 solid AL 10 0.670 266 30 30 30 250 1000
COLOR CODING Standard Products
2 black, white
3 black, white, red
4 black, white, red, blue
Grounding Conductor green
Other special colors are available subject to economic order quantity. Custom cable constructions available for homeruns, multiple oroversized neutrals and isolated grounds. Subject to economicorder quantity.
2 brown, grey
2 orange, grey
2 yellow, grey
2 purple, grey
3 brown, yellow, grey
3 brown, orange, grey
4 brown, orange, yellow, grey
4 brown, yellow, purple, grey
Grounding Conductor green
CONDUCTOR
TYPE*
GROUNDING/
BONDING
CONDUCTOR
AMPACITY (AMPS)‡OVERALL
DIAMETER
(inches)
WEIGHT
(lbs./1000 ft.)75°C
STANDARD PACKAGE
COIL (feet)
CONDUCTOR
SIZE (AWG)/
# OF PHASE
CONDUCTORS
Note: Ampacities are based on Table 310.16 of the NEC, 2005 Edition. *Circuit sizes 12 AWG and 10 AWG also available as stranded conductors. ‡Allowable ampacities shown are for general use as specified by the National Electrical Code, 2005 Edition, Section 310.15. If the equipment is markedfor use at higher temperatures, the conductor ampacity shall be limited to the following per NEC 110.14(C).60°C - When terminated to equipment for circuits rated 100 amperes or less or marked for size 14 through 1 AWG conductors.75°C - When terminated to equipment for circuits rated over 100 amperes or marked for conductors larger than size 1 AWG.90°C - For ampacity derating purposes.Per NEC 310.15(B)(2)(a), the ampacity of 4/C cables shall be reduced by a factor of 0.80 when the neutral is considered a current-carrying conductor.
60°C 90°C
14 / 2 Solid 12 solid AL 0.385 63 15 15 15 250 1000
14 / 3 Solid 12 solid AL 0.410 78 15 15 15 250 1000
14 / 4 Solid 12 solid AL 0.435 96 15 15 15 250 1000
12 / 2 Solid 10 solid AL 0.430 88 20 20 20 250 1000
12 / 3 Solid 10 solid AL 0.445 110 20 20 20 250 1000
12 / 4 Solid 10 solid AL 0.480 134 20 20 20 250 1000
10 / 2 Solid 8 solid AL 0.485 123 30 30 30 250 1000
10 / 3 Solid 8 solid AL 0.520 162 30 30 30 250 1000
10 / 4 Solid 8 solid AL 0.538 202 30 30 30 250 1000
REEL (feet)
COLOR CODING Standard Products
2 black, white
3 black, white, red
4 black, white, red, blue
NUMBER OF CONDUCTORS COLOR SEQUENCE
Other special colors are available subject to economic order quantity.
2 brown, grey
2 orange, grey
2 yellow, grey
2 purple, grey
3 brown, yellow, grey
3 brown, orange, grey
4 brown, orange, yellow, grey
4 brown, yellow, purple, grey
NUMBER OF
CONDUCTORS
COLOR SEQUENCE
277/480Y
MCAP™ Cable - All Purpose
HCF MCAP™ Cable - All Purpose Hospital Care Facility
U.S. Pat. No. 6,486,395
U.S. Pat. No. 6,486,395
CONDUCTOR SIZE/
# OF COND.
(AWG/kcmil)
GROUNDING
CONDUCTOR
(AWG)†
APPROXIMATE
DIAMETER OVER
ARMOR (inches)
WEIGHT
(lbs/1000 ft)
NON WATERTIGHT
CONNECTOR***
(MODEL #)
AMPACITY (AMPS)‡
75°C 90°C
CONDUCTOR SIZE/
# OF COND.
(AWG/kcmil)
GROUNDING
CONDUCTOR
(AWG)†
APPROXIMATE
DIAMETER OVER
ARMOR (inches)
WEIGHT
(lbs/1000 ft)
NON WATERTIGHT
CONNECTOR***
(MODEL #)
AMPACITY (AMPS)‡
75°C 90°C
6/3 6 bare 0.784 240 50 60 NWT 083-075
6/4 6 bare 0.850 289 50 60 NWT 090-075
4-3 6 bare 0.879 298 65 75 NWT 104-100
4-4 6 bare 0.957 368 65 75 NWT 097-100
2-3 4 bare 0.998 411 90 100 NWT 104-100
2-4 4 bare 1.089 508 90 100 NWT 111-100
1-3 4 bare 1.108 496 100 115 NWT 118-100
1-4 4 bare 1.213 619 100 115 NWT 125-125
1/0-3 4 bare 1.188 578 120 135 NWT 125-125
1/0-4 4 bare 1.302 727 120 135 NWT 132-125
2/0-3 4 bare 1.274 678 135 150 NWT 132-125
2/0-4 4 bare 1.398 858 135 150 NWT 148-150
3 brown, orange, grey
4 brown, orange, yellow, grey
NUMBER OF
CONDUCTORS
NUMBER OF
CONDUCTORSCOLOR SEQUENCE
277/480Y
3 black, white, red
4 black, white, red, blue
Grounding Color Bare
COLOR SEQUENCE
120/208Y
COLOR CODING Standard Products
Note: Ampacities are based on Table 310.16 of the NEC, 2005 Edition.‡Allowable ampacities shown are for general use as specified by the National Electrical Code, 2005 Edition, Section 310.15.If the equipment is marked for use at higher temperatures, the conductor ampacity shall be limited to the following per NEC 110.14(C).
60°C - When terminated to equipment for circuits rated 100 amperes or less or marked for size 14 through 1 AWG conductors.75°C - When terminated to equipment for circuits rated over 100 amperes or marked for conductors larger than size 1 AWG.90°C - For ampacity derating purposes.
Per NEC 310.15(B)(2)(a), the ampacity of 4/C cables shall be reduced by a factor of 0.80 when the neutral is considered a current-carrying conductor.†Available with oversized grounding conductor when used for parallel feeds on special orders.***Recommended connectors may require upsizing to accommodate armor looseness after cutting.
Note: Ampacities are based on Table 310.16 of the NEC, 2005 Edition.‡Allowable ampacities shown are for general use as specified by the National Electrical Code, 2005 Edition, Section 310.15.If the equipment is marked for use at higher temperatures, the conductor ampacity shall be limited to the following per NEC 110.14(C).
75°C - When terminated to equipment for circuits rated over 100 amperes or marked for conductors larger than size 1 AWG.90°C - For ampacity derating purposes.
Per NEC 310.15(B)(2)(a), the ampacity of 4/C cables shall be reduced by a factor of 0.80 when the neutral is considered a current-carrying conductor.†Available with oversized grounding conductor when used for parallel feeds on special orders.***Recommended connectors may require upsizing to accommodate armor looseness after cutting.
AlumaFlex™ Cable
3/0-3 4 bare 1.38 830 155 175 NWT 139-125
3/0-4 4 bare 1.61 1135 155 175 NWT 166-150
4/0-3 2 bare 1.59 1086 180 205 NWT 157-150
4/0-4 2 bare 1.74 1370 180 205 NWT 175-200
250-3 2 bare 1.73 1272 205 230 NWT 175-200
250-4 1 bare 1.90 1630 205 230 NWT 193-200
300-3 1 bare 1.84 1470 230 255 NWT 184-200
300-4 1 bare 2.02 1870 230 255 NWT 213-250F
350-3 1 bare 1.94 1649 250 280 NWT 202-300F
350-4 1/0 bare 2.13 2120 250 280 NWT 213-250F
400-3 1 bare 2.04 1826 270 305 NWT 213-250F
400-4 3/0 bare 2.23 2410 270 305 NWT 224-250F
500-3 1 bare 2.20 2172 310 350 NWT 213-250F
500-3 2/0 bare 2.27 2151 310 350 NWT 213-250F
500-3 250 bare 2.27 2200 310 350 NWT 213-250F
500-4 3/0 bare 2.42 2870 310 350 NWT 246-250F
500-4 250 bare 2.95 2863 310 350 NWT 246-250F
600-3 1/0 bare 2.43 2540 340 385 NWT 257-250F
600-4 3/0 bare 3.40 3294 340 385 NWT 271-300F
600-4 400 bare 2.93 3677 340 385 NWT 299-300F
750-3 1/0 bare 2.63 3112 385 435 NWT 271-300F
750-3 3/0 bare 2.63 3171 385 435 NWT 271-300F
750-4 3/0 bare 2.90 4080 385 435 NWT 299-300F
750-4 500 CU bare 3.20 5532 385 435 NWT 328-350F
900-4 250 bare 3.11 4827 425 480 NWT 313-300F
COLOR CODING Standard Products
Low Voltage Colors
AlumaFlex™ Cable
Type MC - 3/0 AWG through 900 kcmil - Non Jacketed THHN/THWN-2
Type MC - 6 AWG through 2/0 AWG - Non Jacketed, Tri-Striped Black XHHW-2
triple e™ Aluminum Alloy
triple e™ Aluminum Alloy
HIGH Voltage Colors
triple e™ Aluminum Alloy
Color sequence for special colors are available subject to economic order quantity.
3 black, white, red
4 black, white, red, blue
Grounding Color Bare
NUMBER OF CONDUCTORSCOLOR SEQUENCE
120/208Y
Note: Phase conductors are black with printed ID.