USES:Ideal for concrete and clay pavers, flat and stamped concrete, ormasonry surfaces such as stucco, retaining walls, concrete wallsand exposed aggregate. Suitable for limestone, sandstone andnatural paving stones. 

PRODUCT DESCRIPTION:SB-9000 Wet Look Sealer will seal and enhance the beauty ofnew and old interlocking pavers, concrete, masonry and otherrelated surface with a rich, enhanced, wet look and gloss finish.The high solids formula combines properties of adhesion,flexibility and UV light resistance to provide a long lasting seal.SB-9000 will penetrate the substrate and provide a protectivelayer on the surface that is resistant to mild acid, alkali and saltattack. SB-9000 will increase the stain resistance of the surfaceto allow for easier cleaning, maintenance and extended wear.SB-9000 can be applied immediately after paver installation, asit is breathable and will not trap naturally occurring efflorescenceand moisture. SB-9000 is a solvent based product and is clearin appearance when applied. SB-9000 is designed as a one-coat application but a second coat may be applied if desired.Cured sealer is freeze resistant to -60°F (-51°C) and is stable upto a temperature of 180°F (82°C). 

TOLL FREE: 800-932-3343 www.sek.us.com

free from oil, dust, loose material, andpreviously applied sealer other than SB-9000 prior to sealer application. Ifneeded, prepare surface with SurebondCleaners before sealing. Thoroughlyrinse all cleaner residue prior to sealing.Allow surface to dry for a minimum of 24hours after cleaning and/or rain beforesealer application. A leaf blower isrecommended to remove dust, debrisand fine sand particles from the surfacebefore sealing. Cover/protect nearbylandscape, vehicles and buildings fromoverspray during application.

APPLICATION INFORMATION:Apply when day and night temperatures are between 40°F - 95°F.Avoid windy conditions to keep sealer spray from drifting. NO pre-blending or mixing required. Do NOT dilute. Apply by airlesssprayer, hand held (pump-up) sprayer, or short nap (solventresistant) roller. Sprayer/equipment should be of solvent resistantdesign with neoprene or Viton type fittings. Hold sprayer nozzleperpendicular to the surface and overlap each coat. If spray andback-roll application is used, use a short (1/4”) nap, solventresistant roller IMMEDIATELY AFTER SPRAYING as the productdries quickly. Short nap will ensure even application. If applying byroller only, it is advised to constantly maintain a wet edge, and tokeep the roller wet with sealer resin to avoid potential lap marksor surface mottling upon drying. Do not roll back and forthexcessively, as this may cause excessive bubbling. Re-rollingimmediately after film starts to become tacky can cause the rollerto become stringy. SB-9000 is designed for a two-coat applicationwith the second coat to be applied only after the first coat has driedto the touch. NOTE: Excessive applications can cause surface tobecome slippery.

DRY TIME:Surface will be dry to the touch in 20-30 minutes assuming 65-85°F. Low surface or air temperature will extend dry times. Protectthe surface from dust, rain, condensation, and traffic while drying.If dry, area can be open to foot & vehicular traffic in 24 hoursdepending on site conditions.

CLEAN UP:For tools and equipment use xylene or toluene.

MAINTENANCE/RE-APPLICATION:Sealed surfaces should be properly maintained following SEK-Surebond’s Restoration and Maintenance System guidelines to get thebest long-term performance from both the pavement and SB-9000.Keep surface clear of buildup of dirt, grime and stains by rinsing withcold, clean water. If staining of surface does occur, Surebond sealersare compatible with Surebond multi-use and specialty cleaners which

TECHNICAL DATA SHEET

PROTECTPROTECT

� CONTRACTOR GRADE FOR RESIDENTIAL AND COMMERCIAL PROJECTS �

CLEANERS SE ADWet Look Sealer

FeaturesWhat makes SB-9000 Wet Look Sealer different?

Enhances

Protective

Stain Resistant

Breathable

Immediate Application

Benefits

• Deeply Enhances Surface Tone with Gloss Finish

• Guards Against Salt, Acid &Other Corrosives

• Promotes Easier Cleaning& Maintenance

• Does Not Trap Moisture orEfflorescence

• Can be Applied Immediately onNew Installations

SB-9000

PRODUCTS FOR SEALING PREPARATION:SureClean - Deep Penetrating Multi-Use CleanerSureStrip - Fast Acting Sealer StripperEfflo Off - Efflorescence, Mineral & Salt Deposit CleanerS.R.B. - Stain & Rust BusterOil Extractor - Oil Stain Cleaner

PREPARATION: TEST FIRSTon a small inconspicuous area to determine the suitability andif desired results are achievable with this product on yourspecific surface. The surface should be thoroughly clean and

Manufactured by SEK/Surebond, Inc. Copyright 2016. All trademarks are the property of SEK/Surebond, Inc. www.sek.us.com

can be used to remove general dirtiness, organic and inorganic stains likeoils, food and beverages and mineral deposits from the surface. Testcleaners in inconspicuous area prior to cleaning. Be sure to check dilutionrates for all cleaners to determine if they are ready to use or to determineappropriate dilution rate especially for sealed surfaces. Efflorescenceshould be removed using Efflo Off and a pressure washer, in conjunctionwith agitation from a natural fiber brush. Care should be taken to ensurethat excessive pressure is not utilized, as it may erode joint sand and coulddamage the surface itself. Thoroughly rinse all cleaner off the surfacebefore sealing.

SB-9000 re-applications may need to be carried out every 3 - 5 yearsdepending on the type of surface and environmental/site conditions.

PACKAGING/SIZES:4 - 1 gallon containers per case5 gallon pails55 gallon drumsBulk packaging available

COVERAGE*:

*Per gallon. Two coats of SB-9000 are recommended. Allow first coat to dry to the touchbefore applying the second coat. Second coat coverage rate is estimated between 350 and400 sq. ft. per gallon (32.5 to 37.2 m/g). Actual coverage may vary depending on the type,age, condition, joint size and porosity of the surface, application method and site conditionssuch as temperature..

STORAGE: Store locked up in original packaging in a cool, well-venti-lated place. Keep container tightly closed when not in use. Do not allowto freeze. SB-9000 is a highly flammable liquid and should be storedaway from heat, hot surfaces, sparks, open flames and other ignitionsources.

SHELF LIFE: 2 years when properly stored

VOC CONTENT: <400 g/L

LIMITATIONS:Protect sealer from freezing and store in a cool place when not in use. Inwinter, keep in heated area. This sealer is not recommended for marble,granite, ceramic tile, and polished surfaces with a high gloss as they donot absorb the sealer. A test area is ALWAYS recommended to determineproduct suitability and compatibility with your specific surface before useand to verify if desired results are achievable. Due to the inherent variabilityof natural stone and clay products, long term performance may vary.Please consult with SEK-Surebond prior to sealing if there are concerns.Do not use SB-9000 in areas subjected to strong solvents, such as

SB-9000 6140

gasoline or brake fluid. The use of an anti-slip additive is recommendedfor increased traction on surface inclines or around consistently wet areassuch as pool deck surrounds. Do not use below grade or where water isalways present. Never try to seal wet or damp surfaces. A minimumtemperature of 40° (5°C) must be maintained for a period of 24 hours priorto application. Surface temperature should not exceed 95°F (35°C) duringapplication. Work should cease in inclement weather (rain or strong wind).

PRECAUTIONARY INFORMATION:KEEP OUT OF REACH OF CHILDREN • Read label and obtain specialinstructions before use • Do not handle until all safety precautions have beenread and understood • Do not eat, drink, or smoke when using this product •Wash thoroughly after handling • Use only outdoors in a well ventilated area •Keep away from heat, hot surfaces, sparks, open flames and other ignitionsources • Ground and bond container and receiving equipment • Useexplosion-proof equipment and only non-sparking tools • Take action to preventstatic discharge • Wear protective gloves, clothing, face and eye protection •Do not breathe vapors, spray or mist • Keep container tightly closed when notin use (See Safety Data Sheet for complete information.)

EMERGENCY & FIRST AID MEASURES: Get medical attention ifexposed and feel unwell, or are concerned. IF INHALED: Remove victim tofresh air and keep at rest in a position comfortable for breathing. Call aPOISON CENTER or physician if feel unwell. IF SWALLOWED: Immediatelycall a POISON CENTER or physician. Do NOT induce vomiting. IF ON SKIN:Immediately take off all contaminated clothing and wash before reuse. Rinseskin with plenty of water or shower. Call a POISON CENTER or physician ifyou feel unwell or if skin irritation occurs. IF IN EYES: Rinse cautiously withwater for several minutes. Remove contact lenses, if present and easy to do.Continue rinsing. Get medical attention if irritation occurs. IN CASE OF FIRE:Use CO2, dry chemical, or alcohol resistant foam to extinguish. (See SafetyData Sheet for complete information.)

WARRANTY: SEK-Surebond warrants its products to substantially conformto its published specifications at the time of purchase. The foregoing is the solelimited warranty applicable to the products. SEK-SUREBOND HEREBYDISCLAIMS ALL OTHER WARRANTIES OF ANY KIND OR NATURE,WHETHER EXPRESS, IMPLIED, OR STATUTORY, INCLUDING WITHOUTLIMITATION THE IMPLIED WARRANTIES OF MERCHANTABILITY,FITNESS FOR A PARTICULAR PURPOSE, OR ANY OTHER WARRANTYOTHER THAN THE WARRANTY SET FORTH ABOVE. The user is solelyresponsible for determining suitability of the products for their particularuse. While the actual application of this product is out of the control of SEK-Surebond, it is recommended that the application guidelines be followedcompletely and accurately. SEK-Surebond’s liability for any damage shallnot exceed the purchase price of the product used, and it shall have no liabilityfor consequential, incidental or punitive damages.

ASSISTANCE & ADDITIONAL INFORMATION:For sales, specification assistance, technical questions, detailing, etc., pleasecontact:

TECHNICAL DATA SHEET

PROTECTPROTECT

S

� CONTRACTOR GRADE FOR RESIDENTIAL AND COMMERCIAL PROJECTS �

MATERIAL SQ FEET SQ METERS

Concrete & Clay Pavers,Exposed Aggregate 250 - 300 23.2 - 27.9

Cast-In-Place & Precast Concrete 200 - 300 18.6 - 27.9

Limestone & Sandstone 150 - 250 13.9 - 23.2

Old Concrete 300 - 400 27.9 - 37.2

3925 Stern Ave.St. Charles, IL 60174Email: info@sek.us.comFax: 630-762-0607

800-932-3343www.sek.us.com

Wet Look SealerSB-9000