pts – production test systemektos.net/wp/wp-content/uploads/2016/11/pts.pdf · 2019. 10. 11. ·...
TRANSCRIPT
PTS – Production Test System
The PTS is an efficient and self contained system for for testing of printed
circuit boards after production. The PTS can help you save time and money
when testing larger quantities of mounted PCBs
What is the PTS?
The PTS consists of a computer which
controls a system that generates stimuli to -
and measures response from - a PCB under
test. An intuitive graphical user interface
shows the status and results of the test
sequence. The PTS performs reliable and
safe operations, and it is easily adjusted to
different types of mounted PCBs.
Which PCBs can be tested?
The PTS can test single PCBs as well as
panels of PCBs. 26*30 cm is the largest
standard size for a PCB, but we offer
customized adjustments for larger boards.
The PTS matches the requirements for
testing typical control PCBs including
digital and analog inputs and outputs.
When needed, the instrumentation
configuration can be expanded to provide
additional I/O capacity such as
communication ports and special signals.
A spring loaded needle bed fixture is
designed for each specific type of PCB, and
each fixture is equipped with handles and a
standard set of connectors for fast, easy,
and reliable docking into the PTS. Getting
started on testing a new type of PCB can be
done within minutes.
A customized test sequence
The individual test sequence for the
particular type of PCB under test is
executed by the pre-installed test software
in the PTS.
The test sequence is easy to read and run,
and the test results can be logged in a
database.
The test program and fixtures are
affordable and will be custom designed for
your PCBs within short notice.
Standard configurationComputer:
Ÿ High Quality Industrial Computer
Ÿ MS Windows
I/O board:
Ÿ 96 x channel 5 V TTL/CMOS DIGITAL I/O: Port A
with 1,2 mA current drive per channel, Port B
and C with 2 mA current.
Ÿ 6 x D/A 12 bit normal, +/- 10 VDC Range
Ÿ 2 x D/A 12 bit up to 1000 VDC galvanic isolation
Signal MUX:
Ÿ 48 channel multi purpose relays. Up to 220 VDC
(or 250 VAC), 2 A, switching power 62, 5 VA
Power MUX:
Ÿ 24 channel multi purpose relays. Up to 250 VDC
(or 250 VAC), 2 A
Instrumentation MUX:
Ÿ 48 channels for measuring voltage up to 220
VDC (or 250 VAC), 2 A, switching power 62, 5 VA.
Ÿ The instrumentation MUX board is divided into
four sections of 12 channels in each section.
Ÿ Each section can work with its own dedicated
measuring instrument or signal generator.
Ÿ The instrumentation board makes interfacing to
generators or instruments very flexible.
Digital multimeter:
Ÿ RIGOL DM 3068, 61/2 digits.
Standard power supplies:
The system comes with the following components
for power supply and signal stimuli to the device
under test:
Ÿ 1 x 230 VAC – 1 A
Ÿ 1 x 115 VAC – 2 A
Ÿ 2 x 12 VAC – 10 A
Ÿ 1 x 24 VDC – 5 A
Ÿ 1 x 12 VDC – 10 A
Ÿ 1 x 5 VDC – 10 A
Options
Ÿ Enlarged test fixture for circuit boards larger
than 26 x 30 cm
Ÿ Additional power supplies
Ÿ Additional communication interfaces
Ÿ Additional multiplexer channels and I/O
channels
Ÿ Additional instruments, loads, oscilloscopes, etc.
to be controlled from the test computer
Ÿ As an option, a barcode scanner can be
purchased and used for easy and secure linking
of stored test data and the individual serial
number of each PCB being tested.
WE OFFER SERVICE AND SUPPORT
Please contact us to find out if the The Production
Test System by EKTOS can help you save time and
money in your production of printed circuit boards.
A section of the test sequence which shows detected
errors on the PCB under test.
WWW.EKTOS.NET
EKTOS A/S
Farvervej 35
8800 Viborg
Denmark
+45 7070 1499
EKTOS-Ukraine LLC
1 Akademika Proskury Str.
61070 Kharkiv
Ukraine
+38 057 760 37 60
November 2016
EKTOS I-Fth227 Vovchynetska 12 FL
76006 Ivano-Frankivsk
Ukraine
+38 094 923 91 54