THIN BED MORTAR

Load-bearingand Partition Walls

* for one bead application for ceramic hollow brick with a width of 12 cm

CERAMIC HOLLOW BRIC

KS

EFFECTIVE 12 m² Wall*

from one can

EXPRESS Application

ELIMINATES Thermal Bridges

POLYURETHANE

SILICATE BLOCKSCELLU

LAR

CO

NC

RET

E

IN

SIDE AND OUTSIDE

STORE IN AN UPRIGHT POSITION

AT TEMP. FROM +5⁰C TO +35⁰C

Net content

750 mlCan capacity

1000

DANGER

TECHNICAL DATA:

Application & Substrate Temperature from -5⁰C to +30⁰C

Can Temperature from +5⁰C to +30⁰C (optimal +20⁰C)

Correction Time < 3 min

Thermal Conductivity (λ) ≤ 0.036 W/mK

Shelf Life 12 months

THIN BED MORTAR POLYURETHANE

APPLICATION: Put the PU Mortar on the long side of the block element keeping 3 cm distance from the side edge of the block.The recommended amount of strips, depending on the width of the masonry:

For details, refer to the technical data sheet, which should be read before application of the product.

PU Mortar yield from one 750 ml can

The width of the masonry block

Recommended number of beads Application of Horizontal [m2]

Application vertically horizontally [m2]

Up to 12 cm 1 10 -12 5 - 8

Above 12 cm 2 5 - 8 3 - 4

PU based Thin Bed Mortar is designed for internal and external walls / load-bearing & partition walls of: - Cellular Concrete Blocks - Ceramic Hollow Blocks - Silicate Blocksin high dimensional tolerance class TLMB (Thin Layer Mortar B).

PU Mortar is suitable for the construction of the walls of single-family homes and multi-family housing.The materials are connected with a thin joint (1-3 mm), which provides high thermal insulation and eliminates the risk of thermal bridges.The work can be carried out at low temperatures (up

construction season.

working product (Thin Bed Mortar is easily applied and quickly cures).Water and electricity are not needed. Construction

the low time investment necessary, easy transport and storage, and maximum utilization of the product.

INSTALLATION GUIDE

PREPARATION:PU Mortar is designed for internal and external walls / load-bearing & partition walls of Cellular Concrete Blocks, Ceramic Hollow Blocks and Silicate Blocks in high dimensional tolerance class TLMB (Thin Layer Mortar B).1.

of traditional mortar. Only this guarantees precise levelling of the whole wall.

2. Surfaces must be free of dust, debris and other materials that would impair the bond strength. Moisten the working surface with water, using e.g. brush or sprayer. Protect surfaces from dirt (of PU mortar).

Surfaces may become dirty from PU Mortar so should be protected e.g. with foil.The optimal can temperature is + 20⁰C. Too cold a can should be heated or conditioned to obtain room temperature.3. Wear protective gloves. 4. Shake can vigorously for 30 seconds to mix

components properly.5. Screw gun onto the can. Hold can upside-down during

application.

APPLICATION:1. Apply the PU Mortar along the brick/ block forming:- one bead in the middle of the block element with a

width of 12 cm- two parallel beads for block elements wider than 12 cm2. 2. Put the PU Mortar on the long side of the block

element keeping 3 cm distance from the side edge of the block/ brick with required diameter:

- about 3 cm for aerated concrete- about 5 cm for hollow ceramic and silicate blocks3. Blocks/ bricks should be put on applied mortar up to 3

min from application (within advised ‘open time”).4. Block/ brick should be pressed slightly in order to

obtain thin joint.5. To achieve the highest precision levelling of the blocks is

necessary. Blocks can be horizontally corrected within 3 minutes by up to 0.5 cm without detaching them from the wall. After PU Mortar application stabilise blocks by using rubber mallet.

Taking the blocks from the wall is inadvisable. In cases where blocks are removed new lines of mortar are required. Vertical application is recommended for the elimination of thermal bridges and in corners and joints with partitions.

CLEANING:When a break in application is longer than 15 minutes, the gun should be blocked and nozzle should be cleaned with cleaner. Keep the gun attached to the can.

FINISHING WORKS:Disconnect the gun from the PU Mortar can. Remove any remaining foam from inside the gun by pressing the trigger. Then clean the tip of the gun and the adaptor using the PU Foam Cleaner. Remove the spray tip from the valve and connect the can with the gun - screwing it into the basket of the gun. Press the trigger several times until the gun is completely cleaned. Block the gun by using the rear dial.

LIMITATION ON THE USE OF PU MORTAR: - Do not mix with other chemicals - Do not use when the substrate temperature is lower than -5⁰C - Do not use when the can temperature is lower than + 5⁰C(Bring the can up to room temperature, about + 20⁰C)After full cure protect the foam against UV radiation e.g. with plaster or bonded insulation board.During the work the conditions of safe use for PU Mortar

Safety Data Sheet.

STORAGE CONDITIONS:Store in a dry, cool and well-ventilated place in an upright position in a closed container. Storage temperature: from +5°C to +35°C (room temperature is recommended).

ignition, oxidizing agents, rubber, plastics, light metals,

months from date of manufacture.

CONTAINS: isocyanates, chloroalkanes C14-C17 phosphate, tris (2-chloro-1-metylenoetylen).

H HAZARD PHRASES: H222: H229: Pressurized container: may burst if heated. H315: Causes skin irritation. H317: May cause an allergic skin reaction. H319: Causes serious eye irritation. H332: Harmful if inhaled. H334: May

if inhaled. H335: May cause respiratory irritation. H351: Suspected of causing cancer. H362: May cause harm to breast-fed children. H373: May cause damage to organs through prolonged or repeated exposure. H410: Very toxic

P PRECAUTIONARY STATEMENTS: P102: Keep out of reach of children. P210: Keep away

No smoking. P251: Do not pierce or burn, even after use. P260: Do not breathe gas/vapours. P271: Use only outdoors or in a well-ventilated area. P280: Wear protective gloves/protective clothing/eye protection/face protection. P302+P352: IF ON SKIN: Wash with plenty of water/ and soap. P304+P340: IF INHALED Remove person to fresh air and keep comfortable for breathing. P305+P351+P338: IF IN EYES Rinse cautiously with water for several minutes. Remove contact lenses if present and easy to do. Continue rinsing. P410+P412: Protect from sunlight. Do not expose to temperatures exceeding 50 °C/122 °F.

INFORMATION WARNING: Contains isocyanates. Can cause an allergic reaction. See information supplied by the manufacturer. If necessary, seek medical advice immediately and show this container or label. Container is pressurized. Heating may cause

incandescent material. Recycle contents / container in accordance with national regulations on waste management. Repeated exposure may cause skin dryness or cracking. Use of this product may cause allergic reactions

asthma, eczema or other skin problems should avoid skin contact with this product. This product should not be used under conditions of poor ventilation unless using

type A1 according to standard EN 14387).

*

INDEX: R-RPP-MORTARID-P0534 AT-15-9562/2015KDWU 57/2017 z 02.01.2017Thin Bed Mortar System 4rd types testsClass 4rd of performancePRODUCTION PLANT: Strefowa 14, 43-100 TychyPRODUCER: RAWLPLUG S.A. ul. Kwidzyńska 6, 51-416 Wrocław, Poland, tel.: 0 801 000 103www.rawlplug.com