PVC Pipe Cutter

This cutter makes smooth clean cuts on small diameter PVC pipe. Also used with polyethylene (PEX) tubing.

Pipe or Burring Reamer

This type of reamer is made with bit brace shank, round shank, or “T” handle.

Flaring Tool

Used to make flared ends for soft tempered tubing.

Pipe Cutter

Too much pressure on the handle may cause the cutting wheel to break.

Teflon Tape

Used for sealing threads on metal and PVC pipe and on valves.

Pipe Die

Pipe dies should not be used for bolt threading as they are tapered.

Pipe Die Stock

Operates as a ratchet in both directions. Hold the pipe die.

Copper Fitting Brush

Used to clean metal parts to be soldered or welded and for cleaning pipe threads.

Copper Tube Cleaning Brush

A wire brush used to clean copper pipe or tubing for soldering. Comes in sizes 1/2" to 1".

Pipe Tap

Used to cut internal threads in pipe fittings.

ABS Cement

Used to connect ABS Plastic pipe and fitting. Black in color. Not compatable with PVC Pipe.

Pipe Vise

Used for holding pipe while cutting and threading.

Pipe Wrench

Adjustable and is used to turn pipe or conduit or round stock. Sizes 6" -18" in length are common, but can be much larger.

Propane Torch

A propane/air torch that develops temperatures suitable for soldering.

Solid Solder

It is available in I or 5 pound spools. Lead free solder is used for plumbing of domestic copper pipe.

Acid Brush

Used for applying pipe joint compound on threaded pipe and thinner's fluid (acid) or flux on copper pipe for soldering. The handle is tubular sheet metal 3/8 inch in diameter and 6 inches long.

Tubing Cutter

Used to cut copper and aluminum tubing.

PVC Glue

When gluing, apply glue to both the fitting and the pipe, slide the two pieces together and rotate 1/4 turn for good adhesion. Glue comes in a variety of thicknesses, set times, and colors.

PEX Crimp Tool

Use to close the crimp fasteners that hold PEX pipe to fittings. There are a number of other systems in use.

PEX Cinch Tool

Use to close the cinch fasteners that hold PEX pipe to fittings. There are a number of other systems in use.

PVC Primer

User to clean and soften PVC pipe before applying cement. Generally recommended for pipe 1" and larger.

SxT Street Ell.

Used to connect PVC pipe to threaded pipe at an angle. May be threaded on both ends, slip on both ends, or slip-thread.

SxSxS Tee

Used to connect three pieces of PVC pipe together. Outlet is commonly smaller than the ends. A typical designation is 1" x 1" x 1/2 SSS Tee. If the outlet is threaded then the designation would be SST.

SxT Reducer Bushing

Used to connect PVC pipe to a smaller diameter threaded pipe.

SxT Elbow

Used to connect PVC pipe to threaded pipe at a 45 or 90 degree angle. May change sizes. Such as 3/4" x 1/2" ST Elbow.

PVC Pipe

Used for cold water purposes, sizes range from 1/2 to 2 inch and it comes in 20 foot lengths.

SxS Reducer Bushing

Used to connect PVC pipes of different diameters.

S Cap

Used to stop the flow on PVC pipe. Slip cap is shown, but can be threaded.

SxS Coupling

Used to connect two pieces of pipe together in a straight line.

SxS Elbow

Comes in 45 and 90 degree angles.

SxS Street Ell

Used to connect two pieces of PVC pipe at an 90 degree angle. One end is male and other is female.

Compression Coupling

Can be used on steel or PVC pipe. Usually used for repair or temporary connections. Seals with a neoprene gasket.

Male Adaptor

The PVC slip end is female and the threaded end is male thread.

Female Adaptor

Used to connect PVC pipe to threaded pipe, has female ends.

SxSxT Tee

Used to connect a straight length of PVC pipe to a threaded pipe at an intersection. Sizes are given as end, end, middle such as 3/4" x 3/4" x 1/2" SST.

Threaded Cap

Used to stop the flow on threaded pipe.

PEX Pipe

Cross-linked polyethylene plastic pipe (tubing) is used for hot and cold water. It is easily worked and used with barbed fittings.

PEX Pinch Clamp

Use to fasten PEX pipe to barbed fittings. Used with a cinch tool. Made of stainless steel.

PEX Crimp Ring

Used to hold the PEX pipe on the barbed fitting. Used with a crimp tool. Commonly made of copper.

PEX Coupling

Couples PEX pipe.

PEX Tee

A barbed tee fitting used with PEX pipe systems. Commonly described by the size or each opening such as 1/2" x 1/2" x 3/4" (end, end, middle).

PEX Elbow

A 90 degree barbed elbow used with PEX systems

PEX Female Adapter

An adapter from the PEX barbed system to female iron pipe threads.

PEX Male Adapter

An adapter from the PEX barbed system to male iron pipe threads.

PEX Stubout

An adapter to copper pipe. Commonly used to with shutoff valves with compression fittings for water supply lines.

Copper Pipe

Rigid pipe used for water supply plumbing. Sizes commonly 1/2" - 2". Connections are soldered. Copper pipe is available in three basic types: Type M is thin-walled, Type L is medium-walled and Type K is thick-walled.

Copper Tubing

Flexible tubing used for water applications. Sizes commonly 1/4"-2" O.D. Connections are soldered, flared, or compression type.

CxC Street Ell

A street elbow for use the copper fittings. Often used with a C x C Ell to make a odd angle.

CxC Union

Used to connect two copper pipes together when neither can be moved.

Paste Flux

Flux is used in soldering to clean pipe allowing solder to flow easily.

C Cap

Used to stop the flow of liquid or gas in a copper pipe.

CxC Coupling

Used to connect two copper pipes together.

CxC Elbow

Comes in 45 and 90 degree angles.

CxT Adaptor or Male Adapter

Used to connect copper pipe to threaded pipe.

CxC Reducing Coupling

Used to connect copper pipes of different diameters.

CxCxC Tee

Used to connect three pieces of copper pipe together.

CxCxT Tee

Used to connect two copper pipes to a threaded pipe.

CxT Female Adapter

Used to adapt to female threads

90 Degree Elbow

A elbow that changes direction by 90 degrees. Both ends are female threads.

Floor Flange

It is a steel flange with female threads in the center and holes drilled on the edge of the flange for bolts or screws.

Galvanized Pipe

Steel pipe with a galvanized coating to prevent corrosion. It Should Not Be Used In Hydraulic Systems.

Union

A three piece fitting. The center piece is hex shaped to accommodate a wrench and tighten the two outer pieces. Used to join two pipes so they can be easily disconnected or join threaded pipe in the middle of a piping run.

Coupling

It is used to connect two pieces of pipe in a straight line.

45 Degree Elbow

A elbow that changes direction by 45 degrees. Both ends are female threads.

Nipple

Short pieces of threaded pipe, nipples are classified as close, short and medium, or are measured in inches of length.

Bushing

Used to reduce pipe size. One end is hex shaped to receive a wrench.

Black Pipe

Pipe lines may be constructed with threaded fittings or may be welded. Used for natural gas not water.

Cross

It is shaped like a cross and is threaded inside at the four ends.

Pipe Plug

The end is square to accommodate a wrench.

Bell Reducer

Similar to a coupling, but changes pipe sizes.

Street Ell

An elbow with male thread on one end and female threads on the other. Available in 90 and 45 degree angles.

Tee

Used to connect lateral branches of a pipe.

Close Nipple

A nipple that is as short as possible (threads touch).

Cap

Used to screw over the threaded end of a pipe to seal the opening.

Pipe Clamp

For 1/2 to 2 inch pipe. Used for repairing small leaks in steel pipe.

ABS Pipe

Acrylonitrile-Butadiene-Styrene (ABS) pipe used for sewer applications. Pipe is black plastic. ABS fittings are glued like other plastic pipe systems. Male and female ends are designated as "spigot" and "hub" respectively. Elbows are not designated by degrees, but rather by the part of the circle (ex. 1/4 bend = 90 degrees). Pipe commonly is found in sizes from 1 1/4" to 6" and 20 foot lengths.

Long Sweep 1/4 Bend Hub

Used to connect ABS pipe at a 90 degree angle and allows for easy clean out when using a drain auger or plumbers snake to clean out lines.

Double Wye Hub

Used for connecting two lines at a 45 degree angle to a straight ABS pipe.

Wye Hub

Used for attaching a line at a 45 degree angle to a straight line.

Male Adaptor-Hub X Male Pipe

Used to connect ABS pipe to female pipe threads.

Female Adaptor-Hub X Female

Used to connect ABS pipe to threaded pipe.

Adaptor-Spigot X Female Pipe

Used to connect female ABS pipe fitting to male pipe thread. Often used for cleanouts.

P Trap Hub With Union

Liquid is held in the base of the P Trap to prevent the passage of air or gasses.

Hose Bib

It has standard pipe threads on one end and hose coupling threads on the other.

Globe Valve

The flow is stopped when the handle is screwed in, forcing the disk over the vent.

Gate Valve

The flow is stopped when the wedge or gate is lowered into the seat.

Check Valve

Once liquid has passed through the valve it cannot flow back.

Ball Valve

By rotating the ball with the handle the valve closes or opens.

Cock Valve

Used to stop the flow of liquid or gas through a pipe. Also called a Stop Cock

Drain Auger

By rotating the auger while feeding it into the line the auger bit tip cuts away the obstruction in the line.

Pipe Joint Compound

Used to seal threaded fittings. May be formulated for use with plastic pipe or steel pipe only.

Plumbers Tape

A galvanized flexible steel tape with holes for screws or nails used to secure plumbing. It is cut to length on the job, wrapped around the pipe and secured with a nail or screw.

Hose Clamp

Used with rubber hose and polyethylene pipe. It consists of a circular steel collar with a tightening screw to secure the hose in place on a barbed fitting.