q913 re1 w1 lec 2

45
Reservoir Engineering 1 Course ( 1 st Ed.)

Upload: hossein-alaminia

Post on 13-Jan-2015

425 views

Category:

Education


5 download

DESCRIPTION

 

TRANSCRIPT

Page 2: Q913 re1 w1 lec 2

1. Petroleum Engineering & Its Importance

2. Petroleum Formation

3. Petroleum ExtractionA. Drilling

B. Production

4. Consumption of Oil

2013 H. AlamiNia Reservoir Engineering 1 Course: (Lec2) Petroleum Reservoirs 2

Page 3: Q913 re1 w1 lec 2

1. Reservoir Fluid Behaviors

2. Petroleum ReservoirsA. Oil

B. Gas

3. Gas Behavior

4. Gas Properties: Z Factor

2013 H. AlamiNia Reservoir Engineering 1 Course: (Lec2) Petroleum Reservoirs 3

Page 4: Q913 re1 w1 lec 2
Page 5: Q913 re1 w1 lec 2

Multiphase Behavior

Naturally occurring hydrocarbon systems found in petroleum reservoirs are mixtures of organic compounds that exhibit multiphase behavior over wide ranges of pressures and temperatures.

These hydrocarbon accumulations may occur in the gaseous state, the liquid state, the solid state, or in various combinations of gas, liquid, and solid.

2013 H. AlamiNia Reservoir Engineering 1 Course: (Lec2) Petroleum Reservoirs 5

Page 6: Q913 re1 w1 lec 2

Petroleum Engineers Task

These differences in phase behavior, coupled with the physical properties of reservoir rock that determine the relative ease with which gas and liquid are transmitted or retained, result in many diverse types of hydrocarbon reservoirs with complex behaviors.

Frequently, petroleum engineers have the task to study the behavior and characteristics of a petroleum reservoir and to determine the course of future development and production that would maximize the profit.

2013 H. AlamiNia Reservoir Engineering 1 Course: (Lec2) Petroleum Reservoirs 6

Page 7: Q913 re1 w1 lec 2

Classification of Reservoirs and Reservoir Fluids Petroleum reservoirs are broadly classified as oil or gas

reservoirs. These broad classifications are further subdivided depending on:The composition of the reservoir hydrocarbon mixtureInitial reservoir pressure and temperaturePressure and temperature of the surface production

The conditions under which these phases exist are a matter of considerable practical importance.

The experimental or the mathematical determinations of these conditions are conveniently expressed in different types of diagrams commonly called phase diagrams. One such diagram is called the pressure-temperature diagram.

2013 H. AlamiNia Reservoir Engineering 1 Course: (Lec2) Petroleum Reservoirs 7

Page 8: Q913 re1 w1 lec 2

Typical P-T Diagram for a Multicomponent System

2013 H. AlamiNia Reservoir Engineering 1 Course: (Lec2) Petroleum Reservoirs 8

Page 9: Q913 re1 w1 lec 2

Pressure-Temperature Diagram

Although a different hydrocarbon system would have a different phase diagram, the general configuration is similar. These multicomponent pressure-temperature diagrams are essentially used to:Classify reservoirsClassify the naturally occurring hydrocarbon systemsDescribe the phase behavior of the reservoir fluid

To fully understand the significance of the pressure-temperature diagrams, it is necessary to identify and define the following key points on these diagrams:Cricondentherm (Tct), Cricondenbar (pcb), Critical point,

Phase envelope (two-phase region), Quality lines, Bubble-point curve, Dew-point curve

2013 H. AlamiNia Reservoir Engineering 1 Course: (Lec2) Petroleum Reservoirs 9

Page 10: Q913 re1 w1 lec 2
Page 11: Q913 re1 w1 lec 2

Oil Reservoirs

Depending upon initial reservoir pressure pi, oil reservoirs can be subclassified into the following categories:Undersaturated oil reservoir. If the initial reservoir

pressure pi, is greater than the bubble-point pressure Pb of the reservoir fluid

Saturated oil reservoir. When pi is equal to the bubble-point pressure of the reservoir fluid

Gas-cap reservoir or two-phase reservoir. If pi is below the bubble point pressure of the reservoir fluidThe appropriate quality line gives the ratio of the gas-cap

volume to reservoir oil volume.

2013 H. AlamiNia Reservoir Engineering 1 Course: (Lec2) Petroleum Reservoirs 11

Page 12: Q913 re1 w1 lec 2

Crude Oils

Crude oils cover a wide range in physical properties and chemical compositions, and it is often important to be able to group them into broad categories of related oils. In general, crude oils are commonly classified into the following types:Ordinary black oilLow-shrinkage crude oilHigh-shrinkage (volatile) crude oilNear-critical crude oil

The above classifications are essentially based upon the properties exhibited by the crude oil, including physical properties, composition, gas-oil ratio, appearance, and pressure-temperature phase diagrams.

2013 H. AlamiNia Reservoir Engineering 1 Course: (Lec2) Petroleum Reservoirs 12

Page 13: Q913 re1 w1 lec 2

Ordinary Black Oil

A typical p-T diagram for an ordinary black oil

Liquid-shrinkage curve for black oil2013 H. AlamiNia Reservoir Engineering 1 Course: (Lec2) Petroleum Reservoirs 13

Page 14: Q913 re1 w1 lec 2

Low-Shrinkage Oil

A typical phase diagram for a low-shrinkage oil

Oil-shrinkage curve for low-shrinkage oil2013 H. AlamiNia Reservoir Engineering 1 Course: (Lec2) Petroleum Reservoirs 14

Page 15: Q913 re1 w1 lec 2

Volatile Crude Oil

A typical p-T diagram for a volatile crude oil A typical liquid-shrinkage curve for a volatile crude oil2013 H. AlamiNia Reservoir Engineering 1 Course: (Lec2) Petroleum Reservoirs 15

Page 16: Q913 re1 w1 lec 2

Near-Critical Crude Oil

A schematic phase diagram for the near-critical crude oil

A typical liquid-shrinkage curve for the near-critical crude oil2013 H. AlamiNia Reservoir Engineering 1 Course: (Lec2) Petroleum Reservoirs 16

Page 17: Q913 re1 w1 lec 2

Liquid Shrinkage for Crude Oil Systems

2013 H. AlamiNia Reservoir Engineering 1 Course: (Lec2) Petroleum Reservoirs 17

Page 18: Q913 re1 w1 lec 2
Page 19: Q913 re1 w1 lec 2

Gas Reservoirs

In general, if the reservoir temperature is above the critical temperature of the hydrocarbon system, the reservoir is classified as a natural gas reservoir. On the basis of their phase diagrams and the prevailing reservoir conditions, natural gases can be classified into four categories:Retrograde gas-condensate

Near-critical gas-condensate

Wet gas

Dry gas

2013 H. AlamiNia Reservoir Engineering 1 Course: (Lec2) Petroleum Reservoirs 19

Page 20: Q913 re1 w1 lec 2

Retrograde Gas-Condensate

A typical phase diagram of a retrograde system

A typical liquid dropout curve (liquid shrinkage volume curve for a condensate

system)2013 H. AlamiNia Reservoir Engineering 1 Course: (Lec2) Petroleum Reservoirs 20

Page 21: Q913 re1 w1 lec 2

Near-Critical Gas-Condensate

A typical phase diagram for a near-critical gas condensate reservoir

Liquid-shrinkage curve for a near-critical gas-condensate system2013 H. AlamiNia Reservoir Engineering 1 Course: (Lec2) Petroleum Reservoirs 21

Page 22: Q913 re1 w1 lec 2

2013 H. AlamiNia Reservoir Engineering 1 Course: (Lec2) Petroleum Reservoirs 22

Wet Gas

Phase diagram for a wet gas

Page 23: Q913 re1 w1 lec 2

2013 H. AlamiNia Reservoir Engineering 1 Course: (Lec2) Petroleum Reservoirs 23

Dry Gas

Phase diagram for a dry gas

Page 24: Q913 re1 w1 lec 2

Compositions of Various Reservoir Fluid Types

2013 H. AlamiNia Reservoir Engineering 1 Course: (Lec2) Petroleum Reservoirs 24

Page 25: Q913 re1 w1 lec 2
Page 26: Q913 re1 w1 lec 2
Page 27: Q913 re1 w1 lec 2

Reservoir Fluid Properties

To understand and predict the volumetric behavior of oil and gas reservoirs as a function of pressure, knowledge of the physical properties of reservoir fluids must be gained.

These fluid properties are usually determined by laboratory experiments performed on samples of actual reservoir fluids.

In the absence of experimentally measured properties, it is necessary for the petroleum engineer to determine the properties from empirically derived correlations.

2013 H. AlamiNia Reservoir Engineering 1 Course: (Lec2) Petroleum Reservoirs 27

Page 28: Q913 re1 w1 lec 2

Natural Gas Constituents

A gas is defined as a homogeneous fluid of low viscosity and density that has no definite volume but expands to completely fill the vessel in which it is placed.

Generally, the natural gas is a mixture of hydrocarbon and nonhydrocarbon gases. The hydrocarbon gases that are normally found in a

natural gas are methanes, ethanes, propanes, butanes, pentanes, and small amounts of hexanes and heavier.

The nonhydrocarbon gases (i.e., impurities) include carbon dioxide, hydrogen sulfide, and nitrogen.

2013 H. AlamiNia Reservoir Engineering 1 Course: (Lec2) Petroleum Reservoirs 28

Page 29: Q913 re1 w1 lec 2

Properties of Natural Gases

Knowledge of PVT relationships and other physical and chemical properties of gases is essential for solving problems in natural gas reservoir engineering. These properties include:Apparent molecular weight, MaSpecific gravity, γgCompressibility factor, zDensity, ρgSpecific volume, v Isothermal gas compressibility coefficient, cgGas formation volume factor, BgGas expansion factor, EgViscosity, μg

The above gas properties may be obtained from direct laboratory measurements or by prediction from generalized mathematical expressions.

2013 H. AlamiNia Reservoir Engineering 1 Course: (Lec2) Petroleum Reservoirs 29

Page 30: Q913 re1 w1 lec 2

Behavior of Ideal Gases

The gas density at any P and T:

Apparent Molecular Weight

Standard Volume

Specific Volume

Specific Gravity

2013 H. AlamiNia Reservoir Engineering 1 Course: (Lec2) Petroleum Reservoirs 30

Page 31: Q913 re1 w1 lec 2

Ideal Gases vs. Real Gases

In dealing with gases at a very low pressure, the ideal gas relationship is a convenient and generally satisfactory tool.

At higher pressures, the use of the ideal gas equation-of-state may lead to errors as great as 500%, as compared to errors of 2–3% at atmospheric pressure.

2013 H. AlamiNia Reservoir Engineering 1 Course: (Lec2) Petroleum Reservoirs 31

Page 32: Q913 re1 w1 lec 2

Behavior of Real Gases

Basically, the magnitude of deviations of real gases from the conditions of the ideal gas law increases with increasing pressure and temperature and varies widely with the composition of the gas. The reason for this is that the perfect gas law was

derived under the assumption that the volume of molecules is insignificant and that no molecular attraction or repulsion exists between them. Numerous equations-of-state have been developed in the

attempt to correlate the pressure-volume-temperature variables for real gases with experimental data.

2013 H. AlamiNia Reservoir Engineering 1 Course: (Lec2) Petroleum Reservoirs 32

Page 33: Q913 re1 w1 lec 2
Page 34: Q913 re1 w1 lec 2

Gas Compressibility Factor Definition

In order to express a more exact relationship between the variables p, V, and T, a correction factor called the gas compressibility factor, gas deviation factor, or simply the z-factor, must be introduced to account for the departure of gases from ideality. The equation has the form of pV = znRT

Where the gas compressibility factor z is a dimensionless quantity and is defined as the ratio of the actual volume of n-moles of gas at T and p to the ideal volume of the same number of moles at the same T and p:

2013 H. AlamiNia Reservoir Engineering 1 Course: (Lec2) Petroleum Reservoirs 34

Page 35: Q913 re1 w1 lec 2

Pseudo-Reduced Properties CalculationStudies of the gas compressibility factors for natural

gases of various compositions have shown that compressibility factors can be generalized with sufficient accuracies for most engineering purposes when they are expressed in terms of the following two dimensionless properties:Pseudo-reduced pressure and Pseudo-reduced temperature

These dimensionless terms are defined by the following expressions:

2013 H. AlamiNia Reservoir Engineering 1 Course: (Lec2) Petroleum Reservoirs 35

Page 36: Q913 re1 w1 lec 2

Standing and Katz Compressibility Factors Chart

2013 H. AlamiNia Reservoir Engineering 1 Course: (Lec2) Petroleum Reservoirs 36

Page 37: Q913 re1 w1 lec 2

Pseudo-Critical Properties Calculation

In cases where the composition of a natural gas is not available, the pseudo-critical properties, i.e., Ppc and Tpc, can be predicted solely from the specific gravity of the gas.

Standing (1977) expressed this graphical correlation in the following mathematical forms:Case 1: Natural Gas Systems

Case 2: Gas-Condensate Systems

2013 H. AlamiNia Reservoir Engineering 1 Course: (Lec2) Petroleum Reservoirs 37

Page 38: Q913 re1 w1 lec 2

2013 H. AlamiNia Reservoir Engineering 1 Course: (Lec2) Petroleum Reservoirs 38

Pseudo-Critical Properties of Natural Gases

Brown et al. (1948) presented a graphical method for a convenient

approximation of the pseudo-critical pressure and pseudo-critical

temperature of gases when only the specific gravity of the gas is

available.

Page 39: Q913 re1 w1 lec 2

Nonhydrocarbon Components of Natural GasesNatural gases frequently contain materials other

than hydrocarbon components, such as nitrogen, carbon dioxide, and hydrogen sulfide.

Hydrocarbon gases are classified as sweet or sour depending on the hydrogen sulfide content. Both sweet and sour gases may contain nitrogen, carbon

dioxide, or both.

A hydrocarbon gas is termed a sour gas if it contains one grain of H2S per 100 cubic feet.

2013 H. AlamiNia Reservoir Engineering 1 Course: (Lec2) Petroleum Reservoirs 39

Page 40: Q913 re1 w1 lec 2

Effect of Nonhydrocarbon Components on the Z-FactorThe common occurrence of small percentages of

nitrogen and carbon dioxide is, in part, considered in the correlations previously cited. Concentrations of up to 5 percent of these

nonhydrocarbon components will not seriously affect accuracy. Errors in compressibility factor calculations as large as 10 percent may occur in higher concentrations of nonhydrocarbon components in gas mixtures.

2013 H. AlamiNia Reservoir Engineering 1 Course: (Lec2) Petroleum Reservoirs 40

Page 41: Q913 re1 w1 lec 2

Nonhydrocarbon Adjustment Methods

There are two methods that were developed to adjust the pseudo-critical properties of the gases to account for the presence of the nonhydrocarbon components. These two methods are the:Wichert-Aziz correction method

Carr-Kobayashi-Burrows correction method

2013 H. AlamiNia Reservoir Engineering 1 Course: (Lec2) Petroleum Reservoirs 41

Page 42: Q913 re1 w1 lec 2

Direct Calculation of Compressibility FactorsAfter four decades of existence, the Standing-Katz

z-factor chart is still widely used as a practical source of natural gas compressibility factors.As a result, there has been an apparent need for a

simple mathematical description of that chart.

Several empirical correlations for calculating z-factors have been developed over the years including:Hall-Yarborough

Dranchuk-Abu-Kassem

Dranchuk-Purvis-Robinson

2013 H. AlamiNia Reservoir Engineering 1 Course: (Lec2) Petroleum Reservoirs 42

Page 43: Q913 re1 w1 lec 2

1. Ahmed, T. (2006). Reservoir engineering handbook (Gulf Professional Publishing). Ch1,2

2013 H. AlamiNia Reservoir Engineering 1 Course: (Lec2) Petroleum Reservoirs 43

Page 44: Q913 re1 w1 lec 2

1. Gas Properties: A. Isothermal gas compressibility (Cg)

B. Gas formation volume factor (Bg)

2. Crude Oil Properties: A. Density

B. Solution gas

C. Bubble-point pressure

D. Oil formation volume factor (Bo)

E. Total formation volume factor (Bt)

2013 H. AlamiNia Reservoir Engineering 1 Course: (Lec2) Petroleum Reservoirs 44

Page 45: Q913 re1 w1 lec 2