qualification for technical colleges - tvtc general for curricula design & development...

CURRICULUM FOR

Department

Computer & Information Technology

Major Network Systems Support

Semesters 1437H - May 2016

Bachelor's Degree

KINGDOM OF SAUDI ARABIA Technical and Vocational Training Corporation Director General for Curricula Design & Development

Qualification for Technical Colleges

KINGDOM OF SAUDI ARABIA Technical and Vocational Training Corporation

Directorate General for Curricula Design & Development

Computer & Information

Technology

Network Systems Support

1

Program Description:

Network Systems Support bachelor program gives you technical knowledge and skills in network

systems support, communications, and security. In this program will cover MCSE, virtual systems, cloud

management, information security, systems administration and more.

This program will give you skills needed to configure and manage different network systems. These

skills are helpful in getting the job in the network system industry. As Telecomm & Electronics College is

a part from MICROSOFT Academy Program, The various certifications (MCSE and MCSE Private

Cloud) are embedded into the program modules.

Most of companies and government organizations are demand for trained networking professionals

to meet the rising network services inside these companies and organizations.

Students complete the program, which provides the knowledge students need in leadership, and

interpersonal and communication skills.

In addition, students can gain real-world experience through participation in the Co-op / training.

Index Content Page 1 Program Description 1

2 Index 1

3 Study Plan 2

4 Brief Description 4

5 Courses Description 6




Technology


2

First semester

Course

Code Course Name Prerequisites

No. of Units CRH L P T CTH

1 MAT 9325 Mathematics (1) 3 2 2 0 4

2 PHY 9325 Physics 3 2 2 0 4

3 ENG 9305 English Language (1) 3 3 0 1 4

4 CMT 325 Computer Programming 3 2 2 0 4

5 NET 345 Computer Networks 3 2 2 0 4

6 NTS 9325 Basic Network Systems

Administration 3 2 2 2 6

Total 18 13 10 3 26

CRH: Credit Hours L: Lecture P: Practical T: Tutorial CTH: Contact Hours

Second semester

Course



1 ISL 9305 Islamic studies 2 2 0 0 2

2 MAT 9326 Mathematics (2) MAT 9325 3 2 2 0 4

3 ENG 9306 English Language (2) ENG 9305 3 3 0 1 4

4 STA 9425 Engineering Statistics and

Probability 4 3 2 0 5

5 NTS 9365 Advanced Network Administration NTS 9325 4 2 4 0 6

6 NTS 367 Network Technologies 1 (CCNA3) NET 345 3 2 2 0 4

Total 19 14 10 1 25


Third semester

Course



1 ARB 9305 Arabic Language 2 2 0 0 2

2 GMS 9437 Engineering Project Management 3 3 0 0 3

3 ENG 9307 English Language (3) ENG 9306 3 3 0 1 4

4 GMS 335 Introduction to Management and

Leadership 2 2 0 0 2

5 NTS 346 Virtual Systems NTS 9325 3 2 2 0 4

6 NTS 368 Network Technologies 2 (CCNA4) NTS 367 3 2 2 0 4

7 NTS 465 Mail Server Management Network NTS 9365 3 2 2 2 6

Total 19 16 6 3 25





Technology


3

Fourth semester

Course



1 GMS 9436 Communication Skills 2 2 0 1 3

2 GMS 9438 Quality Tools and Applications 3 3 0 0 3

3 GMS 9439 Engineering Economy 2 2 0 0 2

4 NTS 366 Network Cloud Management NTS 346 3 2 2 2 6

5 NET 466 Networks and Information Security NET 345 3 2 2 0 4

6 NTS 9496 Project NTS 368 4 2 4 0 6

Total 17 13 8 3 24


Fifth semester

Course


No. of Units

CRH L P T CTH

1 NTS 499 Co-operative Training 4 490

Total 77 56 34 10 100

The total training hours (16X100+490) 2090 CRH: Credit Hours L: Lecture P: Practical T: Tutorial CTH: Contact Hours




Technology


4

Brief Description

Trainee learns also about OSI and TCP/IP protocols by examining packet and protocol traces.

Hands-on exercises include the use of a variety of standard model-based applications and protocols.

NTS 365 Advanced Network Administration

This course provides the skills and knowledge necessary to design and implement a Windows

Server 2012 R2 infrastructure in an enterprise environment.

The course collectively covers designing, planning, deploying, securing, monitoring, automating,

and virtualizing an enterprise server infrastructure.

This course also covers the knowledge and skills needed to provide an enterprise solution that

supports manual and automated server installations in a physical and virtual environment including the

supporting file and storage services.

Additionally, this course covers the knowledge and skills to plan and implement a highly available,

secure infrastructure with focus on Active Directory Federation Service (AD FS), public key

infrastructure (PKI), and Active Directory Rights Management Services (AD RMS). On the other hand,

trainees will learn the skills necessary to provide enterprise-networking solutions such as DHCP, IPAM,

VPN, and Direct Access.

They will also learn the skills necessary to design and implement a forest and domain infrastructure

including multi domains/forest and branch office scenarios.

Trainees will also learn the skills needed to plan and deploy virtual machines including self-service

and automation of virtual machine deployments as well as planning and implementing a monitoring

strategy that includes Microsoft System Center 2012 R2-Operations Manager.

NTS 367 Network Technologies 1 (CCNA3)

This course provides a comprehensive, theoretical, and practical approach to learning the

technologies and protocols needed to design and implement a converged switched network.

Trainees will learn about the hierarchical network design model and how to select devices for each

layer.

The course explains how to configure a switch for basic functionality and how to implement Virtual

LAN's, VTP, and Inter-VLAN routing in a converged network

NTS 346 Virtual systems

This course describes how to monitor and operate a private cloud with Microsoft System Center

2012. IT focuses on how to manage and administer the private cloud, and it describes how you can

monitor key infrastructure elements and applications that run within the private cloud.

This course is intended for datacenter administrators who are responsible for monitoring and

protecting the private cloud infrastructure.

It is also intended for solution architects who are responsible for designing private cloud

architectures and extending existing private cloud solutions. The primary audience for this course is

administrators who create service requests. The secondary audience includes datacenter administrators—

who are responsible for providing provisioning for applications including configuring and deploying

those applications-application/service business owners and administrators who implement service

requests.




Technology


5

NTS 368 Network Technologies 2 (CCNA4)

This course explains the WAN Technologies which is the last of four courses leading to the Cisco

Certified Network Associate (CCNA).

The course focuses on advanced IP addressing techniques (Network Address Translation [NAT],

Port Address Translation [PAT], and DHCP), WAN technology and terminology, PPP, ISDN, DDR,

Frame Relay, network management, and introduction to optical networking

NTS 366 Network Cloud Management

This course describes how to monitor and operate a private cloud with Microsoft System Center

2012.This course focuses on how to manage and administer the private cloud, and it describes how you

can monitor key infrastructure elements and applications that run within the private cloud. As well as, it

will explain the planning and implementation for private cloud

NET 466 Networks and Information Security

The course covers theory and practice of network and information security, focusing in particular

on the security aspects of the network and web. It surveys cryptographic tools used to provide security.

The program validates advanced knowledge and skills required to engineer secure network

infrastructures, web application and data security.

The curriculum emphasizes the real-world best practices of network security engineering utilizing

Cisco IOS Software security features, Cisco ASA adaptive security appliance features, Cisco Intrusion

Prevention Systems (IPSs), Cisco security management tools, and techniques to implement a secure Web

server and application witch PKI.

NTS 467 Management Communication Server

This course will describe how to plan, design, deploy, configure, and administer a Microsoft Lync

Server 2013 solution.

The course emphasizes Lync Server 2013 Enterprise Unified Communications features with

particular emphasis on coexisting with and migrating from legacy communication services.

The labs in this course create a solution that includes IM and Presence, Conferencing, and Persistent

Chat.

This course also will provide trainees the knowledge to design and configure Enterprise Voice and

Online Services in Microsoft Lync Server 2013.

It will provide them with the knowledge and skills to configure and manage a Lync Server 2013 on

premises, in the cloud or in a mixed deployment. In addition, it will provide the skills needed by IT or

telephony consultants to deliver a Lync based enterprise voice solution.




Technology


6

Courses Description

Department Computer & Information

Technology Major Computer Networks

Course Name Computer Networks Course Code NET 345

Prerequisites Credit Hours

CRH

3 CTH 4

L 2 P 2 T 0 CRH: Credit Hours L: Lecture P: Practical T: Tutorial CTH: Contact Hours

Course description :

This course provides a global review of the basic knowledge in computer network and

its applications. It focuses on configuring, managing and troubleshooting elements of the

basic network infrastructure. Trainee learns how to configure workstations, to operate and

manage a basic network.

Trainee learns also about OSI and TCP/IP protocols by examining packet and protocol

traces. Hands-on exercises include the use of a variety of standard model-based applications

and protocols.

Topics :

Module 1 Networking Basics.

Module 2 OSI and TCP/IP Models.

Module 3 Cables and Connectors.

Module 4Data link.

Module 5 Wireless Networking WLAN.

Module 6Addressing and Subnetworks.

Module 7Routing Protocols.

Module 8 Transport Layer.

Module 9 Network Applications.

Module 10 Troubleshooting.

Experiments: If applicable, it will support the course topics.

References :

Bibliography :

Computer Networks, Fifth Edition, by Larry L. Peterson and Bruce S. Davie (Morgan

Kaufmann, 2012). Available on:

http://searchenterprisewan.techtarget.com/feature/Computer-Networks-PDF-Free-

chapter-download

Netography :

www.netacad.net

http://www.scte.org/documents/pdf/CCNA3%20Sample.pdf\

http://www.cisco.com/

http://www.huawei.com/

Detailed of Contents

Contents Hours

1 Module 1 Networking Basics

Identify Computer components, NIC, Ports

Identify characteristics of network ports (speed, voltage, Power…)

4

http://searchenterprisewan.techtarget.com/feature/Computer-Networks-PDF-Free-chapter-download

http://searchenterprisewan.techtarget.com/feature/Computer-Networks-PDF-Free-chapter-download

http://www.netacad.net/

http://www.scte.org/documents/pdf/CCNA3%20Sample.pdf/

http://www.cisco.com/

http://www.huawei.com/




Technology


7

2 Module 3 Cables and Connectors

Identify Cable specification and termination, Coaxial cable, Shielded

copper cable, UTP cable Straight-through, crossover, rollover and

Optical Media.

Realizing twisted Pair Cables

4

3 Module 3 Cables and Connectors

Identify Cable specification and termination, Coaxial cable, Shielded

copper cable, UTP cable Straight-through, crossover, rollover and

Optical Media.

Realizing twisted Pair Cables

4

4 Module 4 Ethernet

Install and configuring Ethernet Network

Assign IP Address (Manually and automatic configuration)

4

5 Module 4 Ethernet

Network Commands: IPconfig, Ping, Netview…

Assign Network groups

4

6 Module 4 Ethernet

Network Commands: IPconfig, Ping, Netview…

Assign Network groups

4

7 Module 5 Wireless Networking (WLAN) Install WLAN Network

Configure WLAN Passwords

Configure Broadcast distance

4

8 Module 5 Wireless Networking (WLAN) Install WLAN Network

Control Access Point

4

9 Module 5 Wireless Networking (WLAN) ( 4 hrs practice )

Install WLAN Network

Configure WLAN Passwords

4

10 Module 5 Wireless Networking (WLAN)

Configure Broadcast distance

Control Access Point

4

11 Module 9 Network Applications

Configuring protocols in Web Pages

Activate/desactivate Services and Ports …

4


How to determine key details related to SMTP, POP-3 and IMAP.

Understand email is sent and read.

4


Understand email is sent and read.

4


Capture traffic for traces.

4

15 Module 9 Troubleshooting

Ethernet Network Troubleshooting

4

16 Module 9 Troubleshooting

Ethernet Network Troubleshooting

4

Total 64




Technology


8

Textbook:


Technology Major Network Systems Support

Course Name Basic Network Systems

Administration Course Code NTS 325


CRH

3 CTH 6



This course provides the skills and knowledge necessary to implement a core

Windows Server 2012 infrastructure in an existing enterprise environment. It collectively

covers implementing, managing, maintaining and provisioning services and infrastructure in

a Windows Server 2012 environment.

In addition, this course focuses on the initial implementation and configuration of core

services, such as Networking, Storage, Active Directory Domain Services (AD DS), Group

Policy, File and Print Services, and Hyper-V.

Topics :

Install and configure servers

Configure server roles and features

Configure Hyper-V

Deploy and configure core network services

Install and administer Active Directory

Create and manage Group Policy

Deploy, manage, and maintain servers

Configure file and print services

Configure network services and access

Configure a Network Policy Server infrastructure

Configure and manage Active Directory

Configure and manage Group Policy

Configure and manage high availability

Configure file and storage solutions

Implement business continuity and disaster recovery

Configure network services

Configure the Active Directory infrastructure

Configure identity and access solutions

Configure access and information protection solutions


References :

http://www.microsoft.com/learning/en-us/mcsa-windows-server-certification.aspx

http://www.microsoft.com/learning/en-us/exam-70-410.aspx

Exam Ref 70-410: Installing and Configuring Windows Server 2012. Published:

October 2012


Training Guide: Administering Windows Server 2012. Published: April 2013

http://www.microsoft.com/learning/en-us/mcsa-windows-server-certification.aspx




Technology


9

(estimated)


Exam Ref 70-412: Configuring Advanced Windows Server 2012 Services. Published:

August 2013 (estimated)


No. Contents Hours

1 Deploying and Managing Windows Server 2012

Deploying Windows Server 2012

Configuring Windows Server 2012 Server Core

Managing Servers

Using Windows PowerShell to Manage Servers

6

2 Lab : Installing Domain Controllers

Installing a Domain Controller

Installing a Domain Controller by Using IFM

Lab : Managing Active Directory Domain Services Objects

Delegating Administration for a Branch Office

Creating and Configuring User Accounts in AD DS

Managing Computer Objects in AD DS

6

3 Lab : Automating AD DS Administration by Using Windows PowerShell

Creating User Accounts and Groups by Using Windows PowerShell

Using Windows PowerShell to Create User Accounts in Bulk

Using Windows PowerShell to Modify User Accounts in Bulk

Lab : Implementing IPv4

Identifying Appropriate Subnets

Troubleshooting IPv4

Lab : Implementing DHCP

Implementing DHCP

Implementing a DHCP Relay Agent (Optional Exercise)

6

4 Lab : Implementing DNS

Installing and Configuring DNS

Creating Host Records in DNS

Managing the DNS Server Cache

6

5 Lab : Implementing IPv6

Configuring an IPv6 Network

Configuring an ISATAP Router

Lab : Implementing Local Storage

Installing and Configuring a New Disk

Resizing Volumes

Configuring a Redundant Storage Space

Lab : Implementing File and Print Services

Creating and Configuring a File Share

Configuring Shadow Copies

Enabling and Configuring Work Folders

Creating and Configuring a Printer Pool

6

6 Lab : Implementing Group Policy 6





Technology


11

Configuring a central store

Creating GPOs

Lab : Increasing Security for Server Resources

Using Group Policy to Secure Member Servers

Auditing File System Access

Auditing Domain Logons

Lab : Configuring App Locker and Windows Firewall

Configuring App Locker Policies

Configuring Windows Firewall

Lab : Implementing Server Virtualization with Hyper-V

Installing the Hyper-V Role onto a Server

Configuring Virtual Networking

Creating and Configuring a Virtual Machine

Using Virtual Machine Checkpoints

7 Lab : Configuring and Troubleshooting DNS

Configuring DNS Resource Records

Configuring DNS Conditional Forwarding

Installing and Configuring DNS Zones

Troubleshooting DNS

Lab : Maintaining AD DS

Installing and Configuring a RODC

Configuring AD DS Snapshots

Configuring the Active Directory Recycle Bin

Optional Exercise- Cloning a domain controller

Lab : Managing User and Service Accounts

Configuring Password Policy and Account Lockout Settings

Creating and Associating a Managed Service Account

6

8 Lab : Implementing a Group Policy Infrastructure

Creating and Configuring Group Policy Objects

Managing GPO Scope

Verify GPO Application

Managing GPOs

Lab : Managing User Desktops with Group Policy

Implement Settings by Using Group Policy Preferences

Managing Office 2013 by using Administrative Templates

Deploying Software by using Group Policy

Configuring Folder Redirection

Lab : Installing and Configuring a Network Policy Server

Installing and Configuring NPS to Support RADIUS

Configuring and Testing a RADIUS Client

6

9 Lab : Implementing Network Access Protection

Configuring NAP Components

Configuring Virtual Private Network Access

Configuring the Client Settings to Support NAP

Lab : Implementing Direct Access by Using the Getting Started Wizard

6




Technology


11

Verifying Readiness for a Direct Access Deployment

Configuring Direct Access

Validating the Direct Access Deployment

Lab : Deploying an Advanced Direct Access Solution

Preparing the Environment for Direct Access

Implementing the Advanced Direct Access Infrastructure

Validating the Direct Access Deployment

10

Lab : Implementing VPN

Implementing VPN

Validating the VPN Deployment

Lab : Implementing Web Application Proxy

Implementing Web Application Proxy

Validating the Web Application Proxy Deployment

Lab : Configuring Quotas and File Screening Using File Server Resource

Manager

Configuring File Server Resource Manager Quotas

Configuring File Screening and Storage Reports

Lab : Implementing Distributed File System

Installing the DFS role service

Configuring a DFS Namespace

Configuring DFS Replication

6

11 Lab : Configuring Encryption and Advanced Auditing

Using Windows BitLocker Drive Encryption to Secure Data Drives

Encrypting and Recovering Files

Configuring Advanced Auditing

Lab : Using Windows Deployment Services to Deploy Windows Server

2012

Installing and Configuring Windows Deployment Services

Creating Operating System Images with Windows Deployment Services

Configuring Custom Computer Naming

Deploying Images with Windows Deployment Services

Lab : Implementing Update Management

Implementing the WSUS Server Role

Configuring Update Settings

Approving and Deploying an Update by using WSUS

Lab : Monitoring Windows Server 2012

Establishing a Performance Baseline

Identifying the Source of a Performance Problem

Viewing and Configuring Centralized Event Logs

6

12 Implementing Advanced Network Services

Configuring Advanced DHCP Settings

Configuring Advanced DNS Settings

Configuring IPAM

Implementing Advanced File Services

Configuring iSCSI Storage

6




Technology


12

Configuring the File Classification Infrastructure

13 Implementing BranchCache

Configuring the Main Office Servers for BranchCache

Configuring the Branch Office Servers for BranchCache

Configuring Client Computers for BranchCache

Monitoring BranchCache

Implementing Secure Data Access

Preparing for DAC deployment

Implementing DAC

Validating and Remediating DAC

Implementing Work Folders

6

14 Implementing Distributed AD DS Deployments

Implementing Child Domains in AD DS

Implementing Forest Trusts

Implementing AD DS Sites and Replication

Modifying the Default Site

Creating Additional Sites and Subnets

Configuring AD DS Replication

Monitoring and Troubleshooting AD DS Replication

Deploying and Configuring CA Hierarchy

Deploying a Stand-Alone Root CA

Deploying an Enterprise Subordinate CA

Deploying and Managing Certificates

Configuring Certificate Templates

Configuring Certificate Enrollment

Configuring Certificate Revocation

Configuring Key Recovery

6

15 Implementing AD RMS

Installing and Configuring AD RMS

Configuring AD RMS Templates

Implementing the AD RMS Trust Policies

Verifying AD RMS on a Client

Implementing AD FS

Installing and Configuring AD FS

Configuring an Internal Application for AD FS

Implementing AD FS for External Partners and Users

Configuring AD FS for a Federated Business Partner

Configuring Web Application Proxy

Implementing NLB

Implementing an NLB Cluster

Configuring and Managing the NLB Cluster

Validating High Availability for the NLB Cluster

6

16 Implementing Failover Clustering

Configuring a Failover Cluster

Deploying and Configuring a Highly Available File Server

6




Technology


13

Validating the Deployment of the Highly Available File Server

Configuring CAU on the Failover Cluster

Implementing Failover Clustering with Hyper-V

Configuring Hyper-V Replicas

Configuring a Failover Cluster for Hyper-V

Configuring a Highly Available Virtual Machine

Implementing Windows Server Backup and Restore

Backing Up Data on a Windows Server 2012 R2 Server

Restoring Files Using Windows Server Backup

96

Textbook:




Technology


14



Course Name Advanced Network

Administration Course Code NTS 365

Prerequisites NTS 325 Credit Hours

CRH

4 CTH 6



This course provides the skills and knowledge necessary to design and implement a

Windows Server 2012 R2 infrastructure in an enterprise environment.

The course collectively covers designing, planning, deploying, securing, monitoring,

automating, and virtualizing an enterprise server infrastructure.

This course also covers the knowledge and skills needed to provide an enterprise

solution that supports manual and automated server installations in a physical and virtual

environment including the supporting file and storage services.

Additionally, this course covers the knowledge and skills to plan and implement a

highly available, secure infrastructure with focus on Active Directory Federation Service

(AD FS), public key infrastructure (PKI), and Active Directory Rights Management

Services (AD RMS).

On the other hand, trainees will learn the skills necessary to provide enterprise

networking solutions such as DHCP, IPAM, VPN, and Direct Access.

They will also learn the skills necessary to design and implement a forest and domain

infrastructure including multi domains/forest and branch office scenarios.

Trainees will also learn the skills needed to plan and deploy virtual machines including

self-service and automation of virtual machine deployments as well as planning and

implementing a monitoring strategy that includes Microsoft System Center 2012 R2-

Operations Manager.

Topics :

Planning Server Upgrade and Migration

Planning and Implementing a Server Deployment Strategy

Planning and Deploying Servers Using Virtual Machine Manager

Designing and Maintaining an IP Configuration and Address Management Solution

Designing and Implementing Name Resolution

Designing and Implementing an Active Directory Domain Services Forest and Domain

Infrastructure

Designing and Implementing an AD DS Organizational Unit Infrastructure

Designing and Implementing a Group Policy Object Strategy

Designing and Implementing an AD DS Physical Topology

Planning and Implementing Storage and File Services

Designing and Implementing Network Protection

Designing and Implementing Remote Access Services

Overview of Management in an Enterprise Data Center

Planning and Implementing a Server Virtualization Strategy

Planning and Implementing Networks and Storage for Virtualization




Technology


15

Planning and Deploying Virtual Machines

Planning and Implementing a Virtualization Administration Solution

Planning and Implementing a Server Monitoring Strategy

Planning and Implementing High Availability for File Services and Applications

Planning and Implementing a High Availability Infrastructure Using Failover

Clustering

Planning and Implementing a Business Continuity Strategy

Planning and Implementing an Public Key Infrastructure

Planning and Implementing an Identity Federation Infrastructure

Planning and Implementing Data Access for Users and Devices

Planning and Implementing an Information Rights Management Infrastructure

Experiments: if applicable it will support the course topics.

References :

http://www.microsoft.com/learning/en-us/mcse-server-infrastructure-certification.aspx

http://www.microsoft.com/learning/en-us/mcse-desktop-infrastructure-

certification.aspx


Exam Ref 70-413: Designing and Implementing a Server Infrastructure. Published:

November 2012


Exam Ref 70-414: Implementing an Advanced Server Infrastructure. Published:

September 2013 (estimated)


No. Contents Hours

1 Planning Server Upgrade and Migration

Planning a Strategy for Server Upgrade and Migration

Evaluating Candidates for Server Virtualization

Planning and Implementing a Server Deployment Strategy

Planning an Automated Server Installation and Deployment Strategy

Preparing the Windows Server 2012 R2 Image

Deploying Windows Server 2012 R2

6

2 Planning and Deploying Servers Using Virtual Machine Manager

Planning Microsoft System Center 2012 R2 Virtual Machine Manager

Components

Planning Virtual Machine and Service Templates

Implementing Virtual Machine Manager Components

Designing and Maintaining an IP Configuration and Address Management

Solution

Planning DHCP to Support Your Proposal

Planning an IPAM Deployment

Implementing DHCP and IPAM

6

3 Designing and Implementing Name Resolution

Designing a Strategy for DNS Name Resolution

Designing a Strategy for DNS Server Placement

6




Technology


16

Designing DNS Zones and DNS Zone Replication

Implementing DNS

4 Designing and Implementing an Active Directory Domain Services Forest

Infrastructure

Designing an Active Directory Forest Infrastructure

Implementing Active Directory Forest Trusts

Designing and Implementing an Active Directory Domain Infrastructure

Designing an Active Directory Domain Infrastructure

Implementing an Active Directory Domain Infrastructure

6

5 Designing and Implementing an AD DS Organizational Unit Infrastructure

Designing an Organizational Unit Infrastructure

Implementing the OU Design

Designing and Implementing an Active Directory Permissions Model

Designing and Implementing a Group Policy Object Strategy

Designing a GPO Strategy

Implementing the GPO Design

6

6 Designing and Implementing an Active Directory Domain Services

Physical Topology

Designing Active Directory Sites and Replication

Planning the Placement of Domain Controllers and Active Directory

Replication

Implementing Active Directory Sites and Domain Controllers

Planning and Implementing Storage

Planning a Storage Solution

Implementing iSCSI Storage

Configuring a Redundant Storage Space

6

7 Designing and Implementing Network Protection

Designing a Windows Firewall Solution

Implementing a Windows Firewall Solution

Designing a NAP Solution

Implementing NAP with IPsec Enforcement

Designing and Implementing Network Access Services

Designing a Remote Access Strategy

Planning and Implementing a Direct Access Solution

Planning and Implementing a VPN Solution

Implementing Web Application Proxy

6

8 Considerations for Implementing an Enterprise Data Center

Planning the Secure Implementation of Services Within an Enterprise

Data Center

Planning and Implementing a Server Virtualization Strategy

Planning a Hyper-V Host Deployment

Configuring Hyper-V Host Groups

Configuring VMM Libraries

6




Technology


17

9 Planning and Implementing Virtual Networks and Storage

Planning a Storage Infrastructure for Virtualization

Planning a Network Infrastructure for Virtualization

Implementing a Storage Infrastructure for Virtualization

Implementing a Network Infrastructure for Virtualization

6

10 Planning and Implementing a Virtual Machine Deployment and

Management Strategy

Planning Virtual Machine and Service Templates

Configuring VMM Profiles and Templates

Implementing Hyper-V Replica

Planning and Implementing an Administration Solution for Virtualization

Configuring Process Automation in System Center

Planning Administrative Delegation and Self-Service in System Center

2012

Configuring Delegated Administration and Self-Service in VM

Implementing Host Updating in VMM

6

11 Implementing a Server Monitoring Strategy

Configuring Server Monitoring Using Windows Server 2012

Implementing Operations Manager Monitoring

Configuring the Operations Manager Monitoring Components

Planning and Implementing High Availability for File Services and

Applications

Planning a High Availability Strategy for File Services

Planning a High Availability Strategy for Web Applications

Implementing a High Availability Solution for File Storage

Implementing a High Availability Solution Using NLB

6

12 Planning and Implementing a Highly Available Infrastructure Using

Failover Clustering

Designing Highly Available Server Roles

Deploying a Failover Cluster

Implementing a Scale-Out File Server

Configuring Cluster-Aware Updating

Implementing Highly Available Virtual Machines

Implementing Operations Manager and VMM Integration

6

13 Implementing a Virtual Machine Backup Strategy with DPM

Configuring DPM

Implementing Backup and Restore for Virtual Machine Data

Implementing Virtual Machine Backup and Recovery using DPM

Planning and Implementing an Active Directory Certificate Services

Infrastructure

Planning the Active Directory Certificate Services Deployment

Deploying the CA Infrastructure

Implementing Certificate Templates

Implementing Certificate Revocation and Distribution

6

14 Planning and Implementing an AD FS Infrastructure

Designing the AD FS Deployment

6




Technology


18

Configuring Prerequisite Components for AD FS

Deploying AD FS for Internal Users

Deploying AD FS for a Partner Organization

Deploying the Web Application Proxy

15 Implementing DAC and Access Denied Assistance

Planning and Implementing DAC

Preparing DAC Deployment

Implementing DAC

Validating and Remediating DAC

6

16 Implementing Work Folders

Preparing and Implementing an Infrastructure for Work Folders

Configuring AD FS and Web Application Proxy For Work Folders

Publishing

Validating Work Folders Functionality

Planning and Implementing an AD RMS Infrastructure

Planning an AD RMS Deployment

Deploying an AD RMS Infrastructure for Internal Users

Implementing AD RMS Integration with Dynamic Access Control

Implementing AD RMS Integration for External Users

6

Total 96

Textbook:




Technology


19



Course Name Network Technologies 1

(CCNA3) Course Code NTS 367

Prerequisites NET 345 Credit Hours

CRH

3 CTH 4



This course provides a comprehensive, theoretical, and practical approach to learning

the technologies and protocols needed to design and implement a converged switched

network.

Trainees will learn about the hierarchical network design model and how to select

devices for each layer. The course explains how to configure a switch for basic functionality

and how to implement Virtual LAN's, VTP, and Inter-VLAN routing in a converged

network

Topics :

Part I: LAN Switching

Introduction to Scaling Networks

Switching and Spanning Tree Protocol

LAN Redundancy

VLANs & VTP

Wireless LANs

Part II: IP Version 6 Routing Protocols

Implementing OSPF for IPv6

Understanding EIGRP Concepts

Implementing EIGRP for IPv6

Troubleshooting Routing Protocols

Part III :Managing IOS Files

License

Experiments: if applicable it will support the course topics.

References :

http://www.cisco.com/web/learning/exams/list/ccna_composite2.html#~Topics

Cisco CCNA Routing and Switching ICND2 200-101 Official Cert

Guidehttp://store.fullpond.com/cisco/ProductCompactBooks.aspx?catalogid=1&categor

yid=0&productid=20229


No. Contents Hours

1 General review for NTS 367 4

2 Introduction to Scaling Networks

Network by Design

Selecting Switching Hardware

Layered Network Design Simulation

4




Technology


21

3 Switching and Spanning Tree Protocol

Understanding Switching and Switches

Initial Configuration of a Catalyst Switch

Spanning Tree Protocol (STP)

Cisco’s additions to STP (Portfast, BPDUGuard, BPDUFilter,

UplinkFast, BackboneFast)

4

4 LAN Redundancy

Rapid Spanning Tree Protocol (RSTP) – 802.1w

Per-VLAN Spanning Tree Plus (PVST+) and Per-VLAN RSTP

(Rapid-PVST)

EtherChannel

4

5 VLANs

MAC Address Table

Virtual LANs (VLANs)

Types of Switch Ports

VLAN Trunking: ISL and 802.1Q

VLAN Trunking Protocol (VTP)

4

6 VTP Inter-VLAN Routing

VLAN Configuration

Inter-VLAN Routing Configuration

VTP Troubleshooting

Voice VLAN Configuration

4

7 Wireless LANs

Make Mine Wireless

Investigating Wireless Implementations

Configuring a Wireless Router and Client

Inside and Outside Control

4

8 Implementing OSPF v3

OSPFv3 ICND1 Configuration Review

Example Multi-Area OSPFv3 Configuration

• Single Area Configuration on the Three Internal Routers

• Adding Multi-Area Configuration on the Area Border

Router

Other OSPFv3 Configuration Settings

• Setting OSPFv3 Interface Cost to Influence Route

Selection

• OSPF Load Balancing

• Injecting Default Routes

4

9 OSPF for IPv6 OSPFv3 Interfaces

• Verifying OSPFv3 Interfaces

• Troubleshooting OSPFv3 Interfaces

OSPFv3 Neighbors

• Verifying OSPFv3 Neighbors

• Troubleshooting OSPFv3 Neighbors

OSPFv3 LSDB and LSAs

4

http://www.freeccnastudyguide.com/study-guides/ccna/ch6/understanding-switches/

http://www.freeccnastudyguide.com/study-guides/ccna/ch6/conf-catalyst-switch/

http://www.freeccnastudyguide.com/study-guides/ccna/ch6/stp-2/

http://www.freeccnastudyguide.com/study-guides/ccna/ch6/stp/

http://www.freeccnastudyguide.com/study-guides/ccna/ch6/stp/

http://www.freeccnastudyguide.com/study-guides/ccna/ch6/6-5-rapid-spanning-tree-protocol-rstp-802-1w/

http://www.freeccnastudyguide.com/study-guides/ccna/ch6/6-6/

http://www.freeccnastudyguide.com/study-guides/ccna/ch6/6-6/

http://www.freeccnastudyguide.com/study-guides/ccna/ch6/6-7-etherchannel/




Technology


21

• Verifying OSPFv3 LSAs

• Troubleshooting OSPFv3 LSAs

OSPFv3 Metrics and IPv6 Routes

• Verifying OSPFv3 Interface Cost and Metrics

Troubleshooting IPv6 Routes Added by OSPFv3

10 Implementing EIGRP

EIGRPv6 Configuration Basics

EIGRPv6 Configuration Example

Other EIGRPv6 Configuration Settings

• Setting Bandwidth and Delay to Influence EIGRPv6

Route Selection

• EIGRP Load Balancing

• EIGRP Timers

4

11 Advanced EIGRP IPv6

EIGRPv6 Interfaces

EIGRPv6 Neighbors

EIGRPv6 Topology Database

EIGRPv6 IPv6 Routes

4

12 Managing IOS Files

Upgrading a Cisco IOS Software Image into Flash Memory

The Cisco IOS Software Boot Sequence

• The Three Router Operating Systems

• The Configuration Register

• How a Router Chooses Which OS to Load

• Recovering If the IOS Does Not Load

• Verifying the IOS Image Using the show version

Command

4

13 IOS Recovery

The General Ideas Behind Cisco Password Recovery/Reset

A Specific Password Reset Example

Configuration File Basics

Copying and Erasing Configuration Files

Initial Configuration (Setup Mode)

4

14 Managing IOS Licensing IOS Images per Model, Series, and per Software Version/Release

Original Packaging: One IOS Image per Feature Set Combination

New IOS Packaging: One Universal Image with All Feature Sets

Managing Software Activation with Cisco License Manager

4

15 IOS Activating

Manually Activating Software Using Licenses

Example of Manually Activating a License

Showing the Current License Status

Adding a Permanent Technology Package License

Right-to-Use Licenses

4

16 General review 4

Total 64




Technology


22

Textbook




Technology


23



Course Name Virtual systems Course Code NTS 346


CRH

3 CTH 4



This course will provide you with the knowledge and skills necessary to create, maintain,

monitor, and protect a virtualization infrastructure. You will learn about creating and managing

virtual machines, managing virtual machine networks, and providing high availability for a

Windows Server® 2012 R2 Hyper-V® environment. This course also will describe how to

create and manage virtual machines, clouds, and services by using Microsoft® System Center

2012 R2 Virtual Machine Manager (VMM).Topics :

Install and configure the Hyper-V server role.

Create virtual machines, create and manage virtual hard disks and work with

snapshots.

Create and configure virtual machine networks in a Hyper-V environment.

Implement virtual machine movement and Hyper-V Replica.

Provide high availability for Hyper-V environment by implementing failover

clustering.

Manage virtual environment by using System Center 2012 R2 Virtual Machine

Manager.

Manage networking and storage infrastructure in Virtual Machine Manager.

Configure and manage Virtual Machine Manager library and library objects.

Create and manage virtual machines by using Virtual Machine Manager.

Create and manage clouds by using System Center 2012 R2 Virtual Machine

Manager.

Create and manage services in System Center 2012 R2 Virtual Machine Manager.

Protect virtualization infrastructure by using Windows Server Backup and Data

Protection Manager.


References :

Bibliography :

www.microsoft.com/en-sa/learning/course.aspx?cid=20409 Netography :

www.microsoft.com




Technology


24


No. Contents Hours

1

Module 1: Evaluating the Environment for Virtualization

Lesson 1: Overview of Microsoft Virtualization

Lesson 2: Overview of System Center 2012 R2 Components

Lesson 3: Evaluating the Current Environment for Virtualization

Lesson 4: Extending Virtualization to the Cloud Environment

Lab: Evaluating the Environment for Virtualization

4

2 Module 2: Installing and Configuring the Hyper-V Role

Lesson 1: Installing the Hyper-V Role

Lesson 2: Managing Hyper-V

Lesson 3: Configuring Hyper-V Settings

Lesson 4: Hyper-V Host Storage and Networking

Lab: Installing and Configuring the Hyper-V Role

4

3

Module 3: Creating and Managing Virtual Hard Disks, Virtual Machines,

and Checkpoints

Lesson 1: Creating and Configuring Virtual Hard Disks

Lesson 2: Creating and Configuring Virtual Machines

Lab A: Creating and Managing Virtual Hard Disks and Virtual Machines

Lesson 3: Installing and Importing Virtual Machines

Lesson 4: Managing Virtual Machine Checkpoints

Lesson 5: Monitoring Hyper-V

Lesson 6: Designing Virtual Machines for Server Roles and Services

Lab B: Creating and Managing Checkpoints and Monitoring Hyper-V

4

4

Module 4: Creating and Configuring Virtual Machine Networks

Lesson 1: Creating and Using Hyper-V Virtual Switches

Lab A: Creating and Using Hyper-V Virtual Switches

Lesson 2: Advanced Hyper-V Networking Features

Lab B: Creating and Using Advanced Virtual Switch Features

Lesson 3: Configuring and Using Hyper-V Network Virtualization

Lab C: Configuring and Testing Hyper-V Network Virtualization

4

5 Module 5: Virtual Machine Movement and Hyper-V Replica

Lesson 1: Providing High Availability and Redundancy for Virtualization

Lesson 2: Implementing Virtual Machine Movement

4

6 Module 5: Virtual Machine Movement and Hyper-V Replica

Lab A: Moving Virtual Machine and Configuring Constrained Delegation

Lesson 3: Implementing and Managing Hyper-V Replica

Lab B: Configuring and Using Hyper-V Replica

4

7 Module 6: Implementing Failover Clustering with Hyper-V

Lesson 1: Overview of Failover Clustering

Lesson 2: Configuring and Using Shared Storage

4

8 Module 6: Implementing Failover Clustering with Hyper-V

Lesson 3: Implementing and Managing Failover Clustering with Hyper-V

Lab: Implementing Failover Clustering with Hyper-V

4

9 Module 7: Installing and Configuring Microsoft System Center 2012 R2

Virtual Machine Manager 4




Technology


25

Lesson 1: Integrating System Center and Server Virtualization

Lesson 2: Overview of VMM

Lesson 3: Installing VMM

Lesson 4: Adding Hosts and Managing Host Groups

Lab: Installing and Configuring System Center 2012 R2 Virtual

Machine Manager

10 Module 8: Managing the Network and Storage Infrastructure in Microsoft

System Center 2012 R2 Virtual Machine Manager

Lesson 1: Managing Networking Infrastructure

Lab A: Network Infrastructure Management

Lesson 2: Managing Storage Infrastructure

Lab B: Managing Infrastructure Storage

Lesson 3: Managing Infrastructure Updates

Lab C: Infrastructure Updates Management

4

11 Module 9: Creating and Managing Virtual Machines by Using Microsoft

System Center 2012 R2 Virtual Machine Manager

Lesson 1: Virtual Machine Management Tasks in VMM

Lesson 2: Creating, Cloning, and Converting Virtual Machines

Lesson 3: Overview of Virtual Machine Updating

Lab: Creating and Managing Virtual Machines by Using System

Center 2012 R2 Virtual Machine Manager

4

12 Module 10: Configuring and Managing the Microsoft System Center 2012

R2

Virtual Machine Manager Library and Library Objects

Lesson 1: Overview of the Virtual Machine Manager Library

Lesson 2: Working with Profiles and Templates

Lab: Configuring and Managing the Microsoft System Center 2012 R2

Virtual Machine Manager Library and Library Objects

4

13 Module 11: Managing Clouds in Microsoft System Center 2012 R2 Virtual

Machine Manager

Lesson 1: Introduction to Clouds

Lesson 2: Creating and Managing a Cloud

4

14 Module 11: Managing Clouds in Microsoft System Center 2012 R2 Virtual

Machine Manager

Lesson 3: Working With User Roles in Virtual Machine Manager

Lab: Managing Clouds in Microsoft System Center 2012 R2

Virtual Machine Manager

4




Technology


26

15 Module 12: Managing Services in Microsoft System Center 2012 R2 Virtual

Machine Manager and App Controller

Lesson 1: Understanding Services in VMM

Lesson 2: Creating and Managing Services in VMM

Lesson 3: Using App Controller 12-16

Lab: Managing Services in Microsoft System Center 2012 R2

Virtual Machine Manager and App Controller

4

16 Module 13: Protecting and Monitoring Virtualization Infrastructure

Lesson 1: Overview of Backup and Restore Options for Virtual Machines

Lesson 2: Protecting Virtualization Infrastructure by Using DPM

Lesson 3: Using Operations Manager for Monitoring and Reporting

Lesson 4: Integrating VMM with Operations Manager

Lab: Monitoring and Reporting Virtualization Infrastructure

4

Total 64

Textbook:




Technology


27



Course Name Network Technologies 2

(CCNA4) Course Code NTS 368


CRH

3 CTH 4



This course explains the WAN Technologies which is the last of four courses leading

to the Cisco Certified Network Associate (CCNA). The course focuses on advanced IP

addressing techniques (Network Address Translation [NAT], Port Address Translation

[PAT], and DHCP), WAN technology and terminology, PPP, ISDN, DDR, Frame Relay,

network management, and introduction to optical networking

Topics :

Part I: Wide-Area Networks Implementing Point-to-Point WANs

Understanding Frame Relay Concepts

Implementing Frame Relay

Identifying Other Types of WANs

Part II: WAN

Types of WANs

Troubleshooting IPv6 Routing

Part III: Network Management

Broadband Solutions

Site-to-Site GRE Tunnels

Managing Network Devices

References :

http://www.cisco.com/web/learning/exams/list/ccna_composite2.html#~Topics

Cisco CCNA Routing and Switching ICND2 200-101 Official Cert Guide

http://store.fullpond.com/cisco/ProductCompactBooks.aspx?catalogid=1&categoryid=0

&productid=20229


No. Contents Hours

1 General review for NTS 367 4

2 Introduction to WAN Technologies

3 Hierarchical Network Design

Class Activity Design Hierarchical

Cisco Enterprise Architecture

Evolving Network Architecture

4

4 Implementing Point-to-Point WANs

Layer 1 Leased Lines

• The Physical Components of a Leased Line

• Leased Lines and the T-Carrier System

• The Role of the CSU/DSU

4




Technology


28

• Building a WAN Link in a Lab

Layer 2 Leased Lines with HDLC

Configuring HDLC

PPP Concepts

• PPP Framing

• PPP Control Protocols

• PPP Authentication

5 Implementing Point-to-Point WANs

Configuring PPP

CHAP Configuration and Verification

Troubleshooting Layer 1 Problems


• Keepalive Failure

• PAP and CHAP Authentication Failure


4

6 Understanding Frame Relay Concepts Virtual Circuits

LMI and Encapsulation Types

Frame Relay Encapsulation and Framing

Frame Relay Local Addressing

Frame Forwarding with One DLCI Field

Frame Relay Layer 3 Addressing: One Subnet Containing All Frame

Relay DTEs

Frame Relay Layer 3 Addressing: One Subnet Per VC

Frame Relay Layer 3 Addressing: Hybrid Approach

4

7 Implementing Frame Relay Planning a Frame Relay Configuration

Configuring Using Physical Interfaces and One IP Subnet

Configuring the Encapsulation and LMI

Frame Relay Address Mapping

Configuring Point-to-Point Subinterfaces

Configuring with Multipoint Subinterfaces

4

8 Implementing Frame Relay OSPF Issues on Frame Relay Multipoint and Physical Interfaces

A Suggested Frame Relay Troubleshooting Process

Layer 1 Issues on the Access Link (Step 1)

Layer 2 Issues on the Access Link (Step 2)

PVC Problems and Status (Step 3)

Frame Relay Mapping Issues (Step 4)

End-to-End Encapsulation (Step 5)

Mismatched Subnet Numbers (Step 6)

4

9 Identifying Other Types of WANs Leased Lines

Frame Relay

Ethernet WANs

MPLS

VSAT

4




Technology


29

Internet Access (WAN) Links

Dial Access with Modems and ISDN

Digital Subscriber Line

Cable Internet

Mobile Phone Access with 3G/4G

PPP over Ethernet 10 Troubleshooting IPv6 Routing

Unicast IPv6 Addresses and IPv6 Subnetting

Assigning Addresses to Hosts

• Stateful DHCPv6

• Stateless Address Autoconfiguration

• Router Address and Static Route Configuration

• Configuring IPv6 Routing and Addresses on Routers

• IPv6 Static Routes on Routers

Verifying IPv6 Connectivity

• Verifying Connectivity from IPv6 Hosts

• Verifying IPv6 from Routers

4

11 Troubleshooting IPv6 Routing Pings from the Host Work Only in Some Cases

Pings Fail from a Host to Its Default Router

Problems Using Any Function That Requires DNS

Host Is Missing IPv6 Settings: Stateful DHCP Issues

Host Is Missing IPv6 Settings: SLAAC Issues

Traceroute Shows Some Hops, But Fails

Routing Looks Good, But Traceroute Still Fails

4

12 Broadband Solutions

Teleworking

Comparing Broadband Solutions

Configuring xDSL Connectivity

4

13 Site-to-Site GRE Tunnels

VPNs

IPsec

Remote Access

4

14 Managing Network Devices

Describing SNMP

The Management Information Base

Configuring SNMP Version 2c

SNMP Version 3

An Overview of System Message Logging

System Message Format

System Message Severity Levels

4

15 Advanced Managing Network Devices

Configuring and Verifying Syslog

Using a Syslog Server

An Overview of NetFlow

4




Technology


31

Network Flows

Configuring NetFlow

Verifying and Using NetFlow

The NetFlow Collector

16 Review 4

Total 56

Textbook:




Technology


31



Course Name Mail server management

network Course Code NTS 465


CRH

3 CTH 6



This course will describes the knowledge and skills to plan, deploy, manage, secure,

and support Microsoft Exchange Server 2013. It explains how to configure Exchange Server

2013 and gives the information which be needed to monitor, maintain, and troubleshoot

Exchange Server 2013. This course will also provide guidelines, best practices, and

considerations that will help trainees optimize performance and minimize errors and security

threats in Exchange Server 2013.

Topics :

Deploying and Managing Microsoft Exchange Server 2013

Planning and Configuring Mailbox Servers

Managing Recipient Objects

Planning and Deploying Client Access Servers

Planning and Configuring Messaging Client Connectivity

Planning and Implementing High Availability

Planning and Implementing Disaster Recovery

Planning and Configuring Message Transport

Planning and Configuring Message Hygiene

Planning and Configuring Administrative Security and Auditing

Monitoring and Troubleshooting Microsoft Exchange Server 2013

Designing and Implementing Site Resilience

Planning Virtualization for Microsoft Exchange Server 2013

Overview of Exchange Server 2013 Unified Messaging

Designing and Implementing Exchange Server 2013 Unified Messaging

Designing and Implementing Message Transport Security

Designing and Implementing Message Retention

Designing and Implementing Messaging Compliance

Designing and Implementing Administrative Security and Auditing


References :

http://www.microsoft.com/learning/en-us/mcse-messaging-certification.aspx




No. Contents Hours




Technology


32

1 Deploying and Managing Exchange Server 2013 Evaluating Requirements and Prerequisites for an Exchange Server 2013

Installation

Deploying Exchange Server 2013

Managing Exchange Server 2013

6

2 Configuring Mailbox Servers Planning Configuration for Mailbox Servers

Configuring Storage on the Mailbox Servers

Creating and Configuring Mailbox Databases

6

3 Managing Recipient Objects Configuring Trey Research Recipients

Configuring Address Lists and Policies for Trey Research

Configuring Public Folders for Trey Research

6

4 Deploying and Configuring a Client Access Server Role Configuring Certificates for the Client Access Server

Configuring Client Access Services Options

Configuring Custom MailTips

6

5 Planning and Configuring Messaging Client Connectivity Planning Client Connectivity

Configuring Outlook Web App and Outlook Anywhere

Configuring Exchange ActiveSync

Publishing Exchange Server 2013 through TMG 2010

6

6 Implementing High Availability

Creating and Configuring a Database Availability Group

Deploying Highly Available Client Access Servers

Testing the High-Availability Configuration

6

7 Implementing Disaster Recovery for Exchange Server 2013 Backing Up Exchange 2013

Restoring Exchange Server 2013 Data

6

8 Planning and Configuring Message Transport Configuring Message Transport

Troubleshooting Message Delivery

Configuring Transport Rules and Data-Loss Prevention Policies

6

9 Planning and Configuring Message Security Configuring Antimalware Options in Exchange Server 2013

Configuring Anti-Spam Options on Exchange Server

Validating Antimalware and Anti-Spam Configuration

6

10 Configuring Administrative Security and Auditing Configuring Exchange Server Permissions

Configuring Audit Logging

Configuring RBAC Split Permissions on Exchange Server 2013

6

11 Monitoring and Troubleshooting Exchange Server 2013 Monitoring Exchange Server

Troubleshooting Database Availability

Troubleshooting Client Access Servers

6

12 Designing and Implementing Site Resiliency Implementing Site Resilience

6




Technology


33

Validating Site Resilience

13 Planning the Virtualization of Exchange Server Roles Designing a Microsoft Exchange Server 2013 Deployment for a Large

Organization

Designing an Exchange Server 2013 Deployment for a Medium-Sized

Organization

Designing an Exchange Server 2013 Deployment for a Medium

Complexity Organization

6

14 Unified Messaging Overview Identifying Unified Messaging Components

Designing and Implementing Exchange Server 2013 Unified Messaging Designing the Unified Messaging Implementation

Configuring Unified Messaging Features

Configuring Unified Messaging Integration with Lync Server 2013

Verify Unified Messaging Functionality

6

15 Designing and Implementing Message Transport Security Planning a Message Transport Implementation

Implementing Message Transport Security

Implementing AD RMS and Exchange Server Integration

Designing and Implementing Message Retention Designing Message Retention and Archiving

Implementing Message Retention and Archiving

6

16 Designing and Implementing Messaging Compliance Designing Messaging Compliance

Implementing Data Loss Prevention

Implementing In-Place eDiscovery

Comparing Messaging Policy and Compliance Options

Designing and Implementing Administrative Security and Auditing Designing a Solution

Implementing Role-Based Access Control

Implementing Mailbox Audit Logging

Using Administrative Audit Logging to Troubleshoot

Implementing and Testing Active Directory Split Permissions

6

Total 96

Textbook:




Technology


34



Course Name Network Cloud Management Course Code NTS 366


CRH

3 CTH 6



This course describes how to monitor and operate a private cloud

with Microsoft System Center 2012.This course focuses on how to manage and administer

the private cloud, and it describes how you can monitor key infrastructure elements and

applications that run within the private cloud. As well as, it will explain the planning and

implementation for private cloud

Topics :

Introduction to the Private Cloud

Configuring and Optimizing Business Unit Clouds

Deploying Cloud Services

Monitoring Private Cloud Services

Configuring Application Performance Monitoring

Operating and Extending Service Management in the Private Cloud

Automatic Incident Creation, Remediation, and Change Requests

Problem Management in the Private Cloud

Automating Self-Service Provisioning

Private Cloud Protection and Recovery

Configuring Compliance in the Private Cloud

Configuring SLAs, Dashboards, and Widgets

Planning for the Private Cloud

Configuring and Deploying the Private Cloud with System Center 2012 -Virtual

Machine Manager

Extending and Maintaining the Private Cloud Infrastructure

Configuring Application Delivery

Creating the Private Cloud Building Blocks

Deploying and Accessing a Private Cloud

Monitoring the Private Cloud Infrastructure

Extending and Customizing Monitoring of the Private Cloud Infrastructure

Implementing Service Management for the Private Cloud

Protecting the Private Cloud Infrastructure

Automating and Standardizing the Private Cloud

Configuring the Cloud Services Process Pack


References :

http://www.microsoft.com/learning/en-us/private-cloud-certification.aspx

http://www.microsoft.com/learning/en-us/exam-70-246.aspx Exam






Technology


35

Contents Hours

1 Verifying the Private Cloud Infrastructure Verifying the Infrastructure

Verifying System Center Components

Verifying the Compliance of the Private Cloud Infrastructure Exercise: Checking Compliance

6

2 Configuring and Optimizing Business Unit Clouds Configuring Network Resources

Creating the Business Unit Cloud

Configuring Security

Importing and Deploying the Stock Trader Application Deploying a Single Tier Service

Configuring Prerequisites

Preparing the Stock Trader Service Template

Deploying the Service Template

6

3 Monitoring Private Cloud Services Deploying an Agent

Configuring Custom Monitoring

Creating a Distributed Application Model

Detecting and Recovering from a Failure

6

4 Configuring Application Performance Monitoring Configuring Basic Monitoring in Application Performance Monitoring

Customizing the Performance Thresholds

Validating Monitoring

Creating a Distributed Application Model for the DinnerNow

Application

6

5 Operating and Extending Service Management in the Cloud Configuring Security Roles

Configuring Notifications

Publishing an Incident Service Offering

Raising an Incident

Creating an Approving a Change Request

Creating an Assigning a Release Record

6

6 Automating Incident Creation, Remediation, and Change Requests Configuring the Incident Template

Configuring Incidents That Affect the StockTrader Service

Automating Incident Remediation and Change Requests

Automating Problem Management in the Private Cloud Manually Creating a Problem Record

Creating a Custom Event Rule in Operations Manager

Configuring Automated Problem Record Creation

6

7 Automating Self-Service Provisioning Completing the Prerequisites for the System Center Cloud Services

Process Pack

Installing the System Center Cloud Services Process Pack

Configuring the System Center Cloud Services Process Pack

Deploying a Virtual Machine for StockTrader by using the Cloud

Services Process Pack

6




Technology


36

Private Cloud Protection and Recovery Configuring Manual Protection and Recovery of Key Service Data

Configuring Automatic Protection and Recovery of Key Service Data

Monitoring Protection Status

8 Configuring Compliance in the Private Cloud Creating an IT GRC Control Management Program

Adding Test Results to a Manual Control Activity and View Compliance

Reports

Assigning a Baseline

6

9 Configuring SLAs, Dashboards, and Widgets Configuring Service Level Tracking

Configuring Service Level Management

Configuring Microsoft Excel Analytics

Configuring PerformancePoint Analytics

Planning for the Private Cloud Deploying the Virtual Machine Manager Agent

Creating a Hyper-V Host Cluster Using VMM

6

10 Configuring and Deploying the Private Cloud Infrastructure Reviewing and Configuring Hosts

Configuring Host Groups

Configuring User Roles and Run As Accounts

Configuring the Library

Preparing the Private Cloud Infrastructure

Deploying a New Virtual Machine

6

11 Maintaining the Private Cloud Infrastructure Configuring a PXE Server in VMM

Configuring a Host Profile

Configuring an Update Server Role in VMM

Configuring a Software Update Baseline in VMM

Configuring Virtual Application Delivery Configuring the Server App-V Sequencer

Configuring the Server App-V Agent

Sequencing an Application

Testing the Server App-V Package Deployment

6

12 Creating the Private Cloud Building Blocks Configuring Profiles

Configuring Virtual Machine Templates

Configuring a Service Template

Configuring a User Role

Deploying the StockTrader Application Service

6

13 Deploying and Accessing a Private Cloud Creating and Configuring a Private Cloud

Configuring App Controller

Creating, Deploying and Managing Services

Monitoring the Private Cloud Infrastructure Deploying Agents

Deploying and Configuring Monitoring Management Packs

6




Technology


37


Configuring VMM Integration

Configuring DPM Integration

14 Extending and Customizing Monitoring Creating Custom Monitoring

Creating a Distributed Application


Creating Views for Private Cloud Infrastructure

Configuring SharePoint Integration

Implementing Service Management for the Private Cloud Configuring Service Manager Basic Settings

Configuring Service Manager Connectors

Configuring the Self-Service Portal


6

15 Protecting the Private Cloud Infrastructure Configuring the Storage Pool

Deploying DPM Protection Agents

Creating and Configuring Protection Groups

Configuring SQL Server Self-Service Recovery

Restoring Data from a SQL Server Protection Group

Performing Self-Service Recovery to Recover SQL Server Data

Automating the Private Cloud Creating a Runbook Server and Configuring Integration Packs

Configuring a Template to Deploy Agents on a New Virtual Machine

Creating a Runbook to Protect All Resources on a Virtual Machine

6

16 Configuring the Cloud Service Process Pack Installing the Cloud Service Process Pack

Configuring User Roles and Settings

Configuring Service Offerings

Creating an Incident Request


6

Total 96

Textbook:




Technology


38


Technology Major Computer Networks

Course Name Network and Information

Security Course Code NET 466

Prerequisites NET 345 Credit Hours

CRH

3 CTH 4



The course covers theory and practice of network and information security, focusing in

particular on the security aspects of the network and web. It surveys cryptographic tools

used to provide security.

The program validates advanced knowledge and skills required to engineer secure

network infrastructures, web application and data security. The curriculum emphasizes the

real-world best practices of network security engineering utilizing Cisco IOS Software

security features, Cisco ASA adaptive security appliance features, Cisco Intrusion

Prevention Systems (IPSs), Cisco security management tools, and techniques to implement a

secure Web server and application witch PKI.

Topics :

Upon successful completion of this course, students will be able to:

Identify the fundamental concepts of network security.

Identify security threats and vulnerabilities.

Implement network security.

Manage certificates.

Identify and implement access control and account management security measures.

Configure Firewalls

Configure a wireless network security.


References :

Computer & Information Technology security handbook, by George Sadowsky and all, the

world bank edition 2003

Computer security handbook, by Seymour Boswrth and all, Wiley edition 2009


Contents Hours

1 Researching Network Attacks and Security Audit Tools :

Researching Network Attacks

Researching Security Audit Tools

4

2 Exploring Encryptions Methods :

Create a Vigenere Cipher Encrypted Message and Decrypt It

Use Steganography to Embed a Secret Message in a Graphic

4

3 Exploring Encryptions Methods :

Symetric and asymmetric encryption

Singing and hashing

4

4 Implementing public key infrastructure : 4




Technology


39

Implementing PKI Windows

Implementing PKI Linux

5 Securing the Router for Administrative Access :

Configure and encrypt all passwords.

Configure enhanced username password security.

Configure enhanced virtual login security.

Configure an SSH server/client on a router.

4

6 Securing the Router for Administrative Access : Create multiple role views and grant varying privileges.

Verify and contrast views.

Secure the Cisco IOS image and configuration files.

Configure Syslog support on a router.

Install a Syslog server on a PC and enable it.

Secure IOS-based Routers using automated features

4

7 User Authentication : Securing Administrative Access Using AAA and

RADIUS

Configure the local user database using Cisco IOS. Configure AAA local authentication using Cisco IOS.

Configure users on the RADIUS server.

4

8 User Authentication : Securing Administrative Access Using AAA and

RADIUS Use Cisco IOS to configure AAA services on a router to access the

RADIUS server for authentication.

Test the AAA RADIUS configuration.

4

9 User Authentication : Kerberos

Install Kerberos server and domain creation

Creation realm, creation account

ACL creation for Kadmin

Installation client

4

10 User Authentication : Kerberos

Installing Kerberized applications for client and server over Windows

and Linux

Test authentication

Configure Kerberos inter domains

4

11 Firewalls: Configuring Basic ASA Settings and Interface Security Levels

Configuring Routing, Address Translation and Inspection Policy Using

CLI.

4

12 Firewalls:

Configuring a DMZ, Static NAT, and ACLs

4

13 IDS & IPS:

Implement Cisco IOS IPS operations

Verify and monitor the Cisco IOS IPS operations

4




Technology


41

14 Securing Layer 2 Switches :

Secure Trunks and Access Ports

Enable storm control for broadcasts.

Configure access ports.

Configure and verify port security.

4

15 Securing Layer 2 Switches :

Configure the PVLAN Edge Feature on a port.

Configure Switched Port Analyzer (SPAN).

Analyze a sourced attack.

4

16 Wireless security :

Analyze Threats in Wireless Networks

Configure simple Authentications

Configure centralized Authentication

Configure authentication and Encryption.

4

Total 64

Textbook:

Handbook of applied cryptography by Alfred J Menezes and all, CRC press

2001

The Cisco Networking Academy CCNA Security.

Security+ Study Guide & DVD Training System, Syngress Publishing 2007

CCNP Security FIREWALL 642-618 Official Cert Guide, David Hucaby and

all, ciscopress 2012.

CCNP Security IPS 642-627 Official Cert Guide, David Hucaby and all,

ciscopress 2012.

CCNP Security SECURE 642-637 Official Cert Guide, Sean Wilkins,

Ciscopress 2011.

Websphere application Server V6.1 security Handbook, Rufus Credle and

all, IBM, 2006.

Wirelless security Handbook by Aoron E Earle, Auerbach publications 2006




Technology


41



Course Name Project Course Code NTS 9496


CRH 4 CTH 6

L 2 P 4 T 0



In this project trainees must design a network system based on all solutions and services they studied

during the program. They must plan and build the project within the 16 weeks of semester.

Topics :

Week 1: Start project planning

Week 2: Project proposal due

Week 3: Share project proposal with peers.

Week 4-7: Project building

Week 8: Midpoint implementation and testing progress report and presentation Week 9-12: Project building

Week 13: Testing and troubleshooting

Week 14: Final inspection and verification

Week 15: All material due to instructor

Week 16: Final demonstration and presentation

qualification for technical colleges - tvtc general for curricula design & development...

Documents