quartz-lite software manual

QUARTZ-LITE3G & 4G Dual LAN Industrial Router Range

Software ManualRev 1.1

http://www.siretta.com

Registered in England No. 08405712VAT Registration No. GB163 04 0349

Siretta LtdBasingstoke Road

Spencers WoodReading

Berkshire RG7 1PW

salesemailweb

+44(0)118 976 [email protected]

2

QUARTZ-LITESoftware Manual

Table of ContentsPage

Introduction 3

About Siretta 4

General Description 5

Local Configuration 6

Basic Configuration 8

Cellular Network Configuration 9

LAN Settings 11

Dynamic DNS Settings 12

Routing Settings 13

WLAN (For wireless QUARTZ-LITE variant ONLY)

14

Basic Settings 14

Wireless Filter Settings 15

Wireless Survey Settings 16

Advanced Network 17

Port Forwarding Settings 17

DMZ Settings 18

Triggered Settings 19

Firewall Settings 20

linkCONNECT Settings 21

UPnp/NAT-PMP Settings 23

Static DHCP Settings 24

VPN Tunnel 25

GRE Settings 25

VPN Client Settings 26

OpenVPN Client Settings 28

Administration 31

Identification Settings 31

Time Settings 32

Admin Access Settings 33

Schedule Reboot Settings 34

SNMP Settings 35

M2M Settings 36

System Log Settings 37

Upgrade Settings 38

System Reboot 38

Debugging 39

Logs Settings 39

Ping Settings 39

Restore Factory Settings 40

Via Web Interface 40

Via Router 41

Appendix (For advanced optional features ONLY)

42

GPS Settings 42

Disclaimer 44

Definitions 45






Berkshire RG7 1PW

salesemailweb


3


The QUARTZ-LITE is a range of UMTS / LTE routers enabling mobile broadband and machine to machine (M2M) industrial communication.

This document is aimed at providing guidance when configuring and using the QUARTZ-LITE router software.

Configuration of the QUARTZ-LITE router can be done via the web using any of the following: Internet Explorer, Firefox, or Chrome. Throughout this document, Internet Explorer 9.0 is used as the example browser.

Introduction






Berkshire RG7 1PW

salesemailweb


4


Siretta, located in Reading, United Kingdom have been manufacturing antennas, cable assemblies and cellular modems for over 10 years. We supply our products globally to many of the world’s leading organisations.

Whether you require an off the shelf or custom solution, Siretta has a wide portfolio of antenna, RF cable assemblies and modems to fit your application.

Our extensive knowledge and experience in the wireless market allows us to support a wide range of customer applications, focusing on frequencies typically within the 75MHz - 5.8GHz range. These encompass the HF, VHF, ISM, GSM/GPRS/3G/4G and GPS frequencies as well as industrial WLAN and VHF/UHF antenna/Wi-Fi antenna solutions.

With a heavy emphasis on design, we have a team of dedicated Application Engineers and Product Managers, backed up by Field Sales Engineers, who specialise in wireless applications.

We have made significant investments in R&D facilities which boast GPS hardware development equipment and a GSM Pico Cell on site, as well as development software and a comprehensive suite of Industrial, Scientific and Medical band, and non ISM band frequency products. We have many technology partners enabling us to keep at the forefront of the communications industry and offer class leading wireless solutions.

About Siretta






Berkshire RG7 1PW

salesemailweb


5


General DescriptionThe Siretta QUARTZ-LITE router is a range of high speed industrial cellular routers in a compact enclosure. The QUARTZ-LITE is offered in 3G / WCDMA / UMTS and 4G / LTE forms giving reliable, secure and high speed wireless connectivity.

The QUARTZ-LITE router range has a number of standard options, such as WiFi, GPS, 1xWAN + 1xLAN interface etc. Additionally QUARTZ-LITE routers are available, as standard with or without an accessory kit comprising: WiFi + GSM antennas, PSU and LAN cable.

VPN features can also be configured in the QUARTZ-LITE routers, enabling utilization of a virtual private network service through a 3G wireless router designed for the stresses and workload of a modern industrial or commercial environment.

The QUARTZ-LITE router series is a high build quality range of routers designed for use in industrial environments needing high performance and a robust hard enclosure as standard. The QUARTZ-LITE range is designed for remote management, telemetry, condition monitoring, CCTV, ATMs, vending machine and other M2M applications.

Its compact small size design, enables the QUARTZ-LITE router to easily be embedded into other equipment or systems. With the GPS option, the QUARTZ-LITE router is ideal for fleet tracking or access management.






Berkshire RG7 1PW

salesemailweb


6


Local ConfigurationThe QUARTZ-LITE router supports configuration by local Ethernet port, you can specify a static IP or DHCP get IP for your computer.

Default IP address: 192.168.1.1 subnet mask: 255.255.255.0

Follow the steps below to configure your router locally:

Step 1. Click “Start > Control Panel”, find the “Network Connections” icon and double click it to enter. Select “Local Area Connection” corresponding to the network card. (See figure 1 below)

Industrial R210 Series Cellular Router User Manual

www.wlink-tech.com 12

3 Router Configuration

This Chapter introduces the parameter configuration of the router, the router can be configured via web internet explorer, Firefox, or chrome. Here we take GUIs 7 system and Internet Explorer 9.0 as sample.

3.1 Local Configure The router supports to be configured by local Ethernet port, you could specify a static IP or DHCP get IP for your computer. The default IP address is 192.168.1.1，subnet mask is 255.255.255.0, please refer to followings:

Step 1 Click “start > control panel”, find “Network Connections” icon and double click it to enter, select “Local Area Connection” corresponding to the network card on this page. Refer to the figure below.

Figure 3-3 Network Connection

Step 2 Obtain a IP address automatically or set up IP address,192.168.1.xxx(XXX can be any number between 2～254)

Step 3 Run an Internet Explorer and visit “http://192.168.1.1/”, to enter identify page.

Figure 1. Network connection

Step 2. Obtain an IP address automatically or set up IP address as: 192.168.1.xxx

NOTE - XXX can be any number between 2~254

Step 3. Open Internet Explorer and visit “http://192.168.1.1/”, to enter identify page.






Berkshire RG7 1PW

salesemailweb


7


Step 4. User should use the default user name and password when logging in for the first time.

Username: adminPassword: admin

Figure 2. User identify interface



User should use the default user name and password when log in for the first time

Figure 3-4 User Identify Interface

----END

3.2 Basic Configuration

Different software version have different web configuration interface, here take R210 2.6.0.1 version as example. After visit the WEB interface, you can check the current status of Router, or modify router configuration via web interface, below is the introduction for the common setting.






Berkshire RG7 1PW

salesemailweb


8




Figure 3-5 Router Status GUI

3.2.1 Cellular Network Configure Step 1 Single Click Basic Network-> Cellular, you can modify relevant parameter

according to the application.

Basic ConfigurationDifferent software versions have different web configuration interfaces, in this example we use version 2.6.0.

After visiting the web interface, you can check the current status of the router or modify the router configuration via the web interface. Below is the interface displaying the routers standard settings.

Figure 3. Router status GUI






Berkshire RG7 1PW

salesemailweb


9


Cellular Network Configuration

Step 1. Select “Basic Network > Cellular” here you can modify cellular and SIM parameters according to your application.

Figure 4. Cellular settings

Parameter Instruction

ICMP checkTo enable or disable ICMP check rules. Enable the ICMP check and setup a reachable IP address as destination IP. Once ICMP check failed, router will switch SIM card.

CSQ limit

SMS password

PIN code Input SIM card PIN code if SIM is setup PIN by ISP

Cellular mode

APNAPN provided by local ISP, usually CDMA/EVDO network do not need this parameter

User SIM card username is provided by ISP

Table 1. Cellular instruction






Berkshire RG7 1PW

salesemailweb


10


ICMP Check

Enabling ICMP on the router will automatically check whether the defined IP address is reachable every 60s. If the IP address is unreachable and ICMP check is timed out at the first check, it will make two further attempts at 3s intervals. If the IP address is still unreachable after the third attempt the router will implement the configured fail action.

The Check IP is a public IP or company server IP address.

Figure 5. ICMP


Password SIM card password is provided by ISP

Auth. type

Use local IP addr.

After all settings have been configured, click the ‘‘Save’’ icon.

Table 1 (continued). Cellular instruction






Berkshire RG7 1PW

salesemailweb


11


LAN Settings

Step 1. Select “Basic Network > LAN” to enter LAN settings page.

Figure 6. LAN setting GUI


Router IP address Router IP address, default IP is 192.168.1.1

Subnet mask Router subnet mask, default mask is 255.255.255.0

DHCPDynamic allocation IP service, after enabled it will show the IP address range and lease options

IP address range IP address range within LAN

Lease The valid time

Table 2. LAN settings instruction



Figure 3-2 LAN Setting GUI

Table 3-2 LAN Setting Instruction


Router IP Address Router IP address, default IP is 192.168.1.1

Subnet Mask Router subnet mask, default mask is 255.255.255.0

DHCP Dynamic allocation IP service, after enable, it will show the IP address range and options of lease

IP Address Range IP address range within LAN

Lease The valid time

Step 2 After setting, please click “save” to finish, the device will reboot.

----End







Berkshire RG7 1PW

salesemailweb


12



IP addressUse default IP 0.0.0.0. For customized protocol, please contact Siretta representative.

Auto refresh time Set the interval refresh of the DDNS client to 240s or above

Service provider Select the DDNS service provider listed

Table 3. DDNS settings instruction




3.2.3 Dynamic DNS Setting Step 1 Single click “Basic Network->DDNS to enter the DDNS setting page.

Figure 3-3 Dynamic DNS Setting

Table 3-3 DDNS Setting Instruction

parameter Instruction

IP address Default is standard DDNS protocol, for customized protocol, please contact Wlink engineer. Usually, use default IP 0.0.0.0

Auto refresh time

Set the interval of the DDNS client obtains new IP, suggest 240s or above

Service provider

Select the DDNS service provider that listed.

Step 2 Please Click “Save“ to finish.

----End

3.2.4 Routing Setting Step 1 Single click “Basic Network->Routing to enter the DDNS setting GUI.

Dynamic DNS Settings

Step 1. Select “Basic Network > DDNS” to enter the DDNS settings page.

Figure 7. Dynamic DNSS settings






Berkshire RG7 1PW

salesemailweb


13



Destination Router can reach the destination IP address

Gateway Next hop IP address which the router will reach

Subnet Mask Subnet mask for destination IP address

MetricMetrics are used to determine whether one particular route should be chosen over another

Interface Interface from router to gateway

Description Describe routing name

Table 4. Routing settings instruction




Figure 3-4 Routing Setting

Table 3-4 Routing Setting Instruction


Destination Router can reach the destination IP address.

Gateway Next hop IP address which the router will reach

Subnet Mask Subnet mask for destination IP address

Metric Metrics are used to determine whether one particular route should be chosen over another.

Interface Interface from router to gateway.

Description Describe this routing name.

Step 2 Please Click “ Save “ to finish.

3.3 WLAN Setting It’s mainly for router which support Wi-Fi, you can modify and configure WLAN

parameter through Web GUI, below is the common setting 3.3.1 Basic Setting Step 1 Click “WLAN->Basic Setting” to configure relative parameter

Routing Settings

Step 1. Select “Basic Network > Routing” to enter the Routing settings page.

Figure 8. Routing settings






Berkshire RG7 1PW

salesemailweb


14


WLAN (For wireless QUARTZ-LITE variant ONLY)

Step 1. Select “WLAN > Basic Setting” to enter the WLAN settings page.

Figure 9. WLAN settings


Enable wireless Enable or disable the Wireless

Wireless mode Support AP, AP+WDS, Bridge, Client, WDS

Wireless network protocol Support Auto, IEEE 11b/g/n selectable

SSIDThe default is router, can be modified as per application

Channel The channel of wireless network, keep the default

Channel Width 20MHz and 40MHz alternative

Security Support various encryption methods

Table 5. WLAN settings instruction

Configuration of the routers WLAN parameter through Web GUI.

Basic Settings



Figure 3-5 WLAN Basic Settings GUI

Table 3-5 Basic Setting Instruction


Enable wireless Enable or Disable the Wireless

Wireless mode Support AP, AP+WDS, Bridge, Client, WDS

Wireless Network protocol

Support Auto, IEEE 11b/g/n selectable

SSID The default is router, can be modified as per application.

Channel The channel of wireless network, suggest keep the default

Channel Width 20MHZ and 40MHZ alternative

Security Support various encryption method

Step 2 Please click “Save” to finish.

----End

3.3.2 Wireless Filter Setting Step 1 Single click “WLAN > Wireless Filter”. After all settings have been configured, click the ‘‘Save’’ icon.






Berkshire RG7 1PW

salesemailweb


15


Step 1. Select “WLAN > Wireless Filter” to enter the wireless filter settings page.

Figure 10. Wireless filter settings


Disable Filter Enable or Disable the Wireless

Permit on the following client

Only allow the listed MAC address to connect to router by wireless connection

Block the follow ClientPrevents the listed MAC address connecting to the router by wireless connection

Table 6. WLAN basic settings instruction

Wireless Filter Settings


The Wireless Filter enables permitting/prohibiting specific clients connection to WiFi. This feature is invalid for wired connections.



Figure 3-6 Wireless Client Filter Setting GUI

The Wireless Filter enable to set the permitted client or prohibit the specific client to connect the WiFi, However, this feature is invalid for wired connection application.

Table 3-6 ”Wireless Client Filter” Setting Instruction


Disable Filter Choose to disable


Only allow the listed MAC address to connect to router by wireless

Block the follow Client

Prevent the listed MAC address to connect to router by wireless

Step 2 Please click ”save” to finish

----End

3.3.3 Wireless Survey Step 1 Please click “WLAN> Wireless Survey” to check survey.






Berkshire RG7 1PW

salesemailweb


16


Step 1. Select “WLAN > Wireless Survey” to check the survey.

Figure 11. Wireless survey check

Wireless Survey Settings



Figure 3-6 Wireless Client Filter Setting GUI

The Wireless Filter enable to set the permitted client or prohibit the specific client to connect the WiFi, However, this feature is invalid for wired connection application.

Table 3-6 ”Wireless Client Filter” Setting Instruction


Disable Filter Choose to disable


Only allow the listed MAC address to connect to router by wireless

Block the follow Client

Prevent the listed MAC address to connect to router by wireless


----End

3.3.3 Wireless Survey Step 1 Please click “WLAN> Wireless Survey” to check survey.






Berkshire RG7 1PW

salesemailweb


17




Figure 3-7 Wireless Survey Setting GUI

----End

3.4 Advanced Network Setting 3.4.1 Port Forwarding Step 1 Please click “Advanced Network > Port Forwarding” to enter the GUI, you may

modify the router name, Host name and Domain name according to the application requirement.

Figure 3-8 Port Forwarding GUI

Table 3-7 “Port Forwarding” Instruction


Protocol Support UDP, TCP, both UDP and TCP

Src. Address Source IP address. Forward only if from this address.

Ext. Ports External ports. The ports to be forwarded, as seen from the WAN.

Int. Port Internal port. The destination port inside the LAN. If blank, the destination port is the same as Ext Ports. Only one port per entry is supported when forwarding to a different internal port.

Int. Address Internal Address. The destination address inside the LAN.

Description Remark the rule


----End

Step 1. Select “Advanced Network > Port Forwarding” to enter the port forwarding settings. You can modify the router name, host name and domain name according to the application requirement.

Figure 12. Port forwarding settings

Advanced NetworkPort Forwarding Settings



Src. Addressclient Source IP address. Forward only if from this address.

Ext. PortsExternal ports. The ports to be forwarded, as seen from the WAN.

Int. Port

Internal port. Destination port inside the LAN. If blank, the destination port is the same as Ext Ports. Only one port per entry is supported when forwarding to a different internal port.

Int. Address Internal Address. Destination address inside the LAN.

Description Remark the rule

Table 7. Port forwarding settings instruction







Berkshire RG7 1PW

salesemailweb


18




3.4.2 DMZ Setting Step 1 Please click “Advanced Network> DMZ” to check or modify the relevant

parameter.

Figure 3-9 DMZ GUI

Table 3-8 “DMZ” Instruction


Destination Address

The destination address inside the LAN.

Source Address Restriction

If no IP address inside, it will allow all IP address to access. If define IP address, it will just allow the defined IP address to access.

Leave Remote Access


----End

3.4.3 Triggered Setting Step 1 Please click “Advanced Network> Triggered” to check or modify the relevant

parameter.

Step 1. Select “Advanced Network > DMZ” to enter the DMZ settings.

Figure 13. DMZ settings

DMZ Settings


Destination Address Destination address inside the LAN

Source AddressRestriction

If there is no IP address here, it will allow access to all IP address. If an IP address is defined, access will be allowed to this IP address only.

Leave Remote Access Leave remote access

Table 8. DMZ settings instruction







Berkshire RG7 1PW

salesemailweb


19


Step 1. Select “Advanced Network > Triggered” to enter the triggered settings.

Figure 14. Triggered settings

Triggered Settings


Protocol Supports UDP, TCP, both UDP and TCP

Triggered Ports Trigger ports are the initial LAN to WAN “trigger”

Transferred PortsTransferred ports are the WAN to LAN ports that are opened if the “trigger” is activated

NotePort triggering opens an incoming port when your computer is using a specified outgoing port for specific traffic

Table 9. Triggered settings instruction




Figure 3-10 Triggered GUI

Table 3-9 “Triggered” Instruction



Triggered Ports Trigger Ports are the initial LAN to WAN "trigger".

Transferred Ports

Forwarded Ports are the WAN to LAN ports that are opened if the "trigger" is activated.

Note Port triggering opens an incoming port when your computer is using a specified outgoing port for specific traffic.

Step 2 Please click ”save” to finish.

----End

3.4.4 Firewall Setting Step 1 Please click “Advanced Network> Firewall” to check or modify the relevant

parameter.






Berkshire RG7 1PW

salesemailweb


20


Step 1. Select “Advanced Network > Firewall” to enter the firewall settings.

Figure 15. Firewall settings

Firewall Settings


Applies To White list

Blocked Resources Black list

Table 10. Firewall settings instruction




Figure 3-11 Firewall Setting GUI

Table 3-10 “Firewall” Instruction


Applies To White list.

Blocked Resources

Black list.


3.4.5 Serial App. Setting Step 1 Please click “Advanced Network> Serial App” to check or modify the relevant

parameter.






Berkshire RG7 1PW

salesemailweb


21


Step 1. Select “Advanced Network > linkCONNECT” to enter the linkCONNECT settings.

Figure 16. linkCONNECT settings

linkCONNECT Settings


Serial to TC/IP mode Disable, Server and Client mode

Server IP/Port IP address and domain name for Server IP

Socket Type TCP/UDP protocol

Socket Timeout Setting time to transmit data to serial port

Serial TimeoutSerial timeout is the waiting time for transmitting a data packet. The default setting is 500ms.

Packet payloadPacket payload is the maximum transmission length for serial port data packet. The default setting is 1024bytes.

Heart-beat ContentSend heart beat to the defined server to keep router online. It is convenient to monitor the router from the server.

Table 11. linkCONNECT settings instruction






Berkshire RG7 1PW

salesemailweb


22



Heart beat Interval Heart beat interval time

Baud Rate 112100 as default

Parity Bit None as default

Data Bit 8bit as default

Stop Bit 1bit as default

Table 11 (continued). linkCONNECT settings instruction







Berkshire RG7 1PW

salesemailweb


23


Step 1. Select “Advanced Network > Upnp/NAT-PMP” to enter the Upnp/NAT-PMP settings.

Figure 17. Upnp/NAT-PMP settings

UPnp/NAT-PMP Settings



Figure 3-13 UPnp/NAT-PMP Setting GUI


3.4.7 Static DHCP Setting Step 1 Please click “Advanced Network> Static DHCP” to check or modify the relevant

parameter.

Figure 3-14 Static DHCP Setting GUI








Berkshire RG7 1PW

salesemailweb


24


Step 1. Select “Advanced Network > Static DHCP” to enter the static DHCP settings.

Figure 18. Static DHCP settings

Static DHCP Settings




Figure 3-13 UPnp/NAT-PMP Setting GUI


3.4.7 Static DHCP Setting Step 1 Please click “Advanced Network> Static DHCP” to check or modify the relevant

parameter.

Figure 3-14 Static DHCP Setting GUI







Berkshire RG7 1PW

salesemailweb


25


Step 1. Select “VPN Tunnel > GRE” to enter the GRE settings.

Figure 19. GRE settings

GRE Settings


Remote IP Address GRE peer IP address. Usually a public IP address.

Local IP Address Local IP address for LAN

Tunnel Local IP AddressGRE Tunnel local IP address which is a virtual IP address

Remote LAN IP AddressGRE Tunnel remote IP address which is a virtual IP address

ICMP Check IP AddressChecks the IP address is reachable. If ICMP check is failed, GRE will be established again.

Table 12. GRE settings instruction

VPN Tunnel







Berkshire RG7 1PW

salesemailweb


26


Step 1. Select “VPN Tunnel > VPN Client” to enter the VPN client settings.

Figure 20. VPN client settings

VPN Client Settings


VPN Mode VPN Mode for PPTP and L2TP

Server Address VPN Server IP address

User name As the configuration requested

Password As the configuration requested

Encryption As the configuration requested

Stateless MPPE As the configuration requested

Accept DNS As the configuration requested

Table 13. VPN client settings instruction






Berkshire RG7 1PW

salesemailweb


27



Remote Subnet As the configuration requested

Create NAT on Tunnel As the configuration requested

Table 13 (continued). VPN client settings instruction







Berkshire RG7 1PW

salesemailweb


28


Figure 21. VPN client settings

OpenVPN Client Settings

Basic

Step 1. Select “VPN Tunnel > OpenVPN Client” to enter the OpenVPN settings.

Step 2. Select “Client 1 > Basic” in the OpenVPN settings banner.


Poll Interval Check routers status as interval time

Redirect Internet Traffic Configure OpenVPN as default routing

Access DNS As the configuration

Encryption

Compression As the configuration

TLS Renegotiation Time 1 as default for 60s

Connection Retry Time OpenVPN retry to connection interval

Verify Server Certificate As the configuration

Custom Configuration As the configuration

Table 14. OpenVPN Client 1 basic settings instruction


Basic settings






Berkshire RG7 1PW

salesemailweb


29



Step 2. Select “Client 2 > Advanced” in the OpenVPN settings banner.

Figure 22. OpenVPN settings

Advanced

Advanced settings


Poll Interval OpenVPN client check router’s status as interval time

Redirect Internet Traffic Configure OpenVPN as default routing

Access DNS As the configuration

Encryption

Compression As the configuration

TLS Renegotiation Time 1 as default for 60s

Connection Retry Time OpenVPN retry to connection interval

Verify Server Certificate As the configuration

Custom Configuration As the configuration

Table 15. OpenVPN Client 2 advanced settings instruction







Berkshire RG7 1PW

salesemailweb


30



Step 2. Select “Client 2 > Keys” in the OpenVPN settings banner.

Figure 23. OpenVPN settings

Keys

Keys settings


Certificate Authority Keep certificate the same as the server

Client Certificate Keep client certificate the same as the server

Client Key Keep client key the same as the server

Table 16. OpenVPN Client 2 keys settings instruction







Berkshire RG7 1PW

salesemailweb


31


Step 1. Select “Administrator > Identification” to enter the router identification settings. Here you can modify the router name, host name and domain name according to your requirements.

Figure 24. Router identification settings

Identification Settings


Router Name Default is router. Can be customised, maximum 32 characters.

Host Name Default is router. Can be customised, maximum 32 characters.

Domain NameDefault is empty. Can be customised, maximum 32 characters. This is the domain name for the WAN, it will only need to be configured in WAN applications.

Table 17. Router identification settings instruction

Administration







Berkshire RG7 1PW

salesemailweb


32


Step 1. Select “Administrator > Time” to enter the time settings.

Figure 25. Time settings

Time Settings


NOTE - If the device is online but time update fails, try another NTP time server.






Berkshire RG7 1PW

salesemailweb


33


Step 1. Select “Administrator > Admin” to enter the admin settings. Here, you can configure the basic web parameters enabling it to be more convenient for your usage. NOTE - The password is the router system account password.

Figure 26. Admin settings

Admin Access Settings







Berkshire RG7 1PW

salesemailweb


34


Step 1. Select “Administrator > Schedule Reboot” to enter the reboot settings.

Figure 27. Reboot settings

Schedule Reboot Settings







Berkshire RG7 1PW

salesemailweb


35


Step 1. Select “Administrator > SNMP” to enter the SNMP settings.

Figure 28. SNMP settings

SNMP Settings







Berkshire RG7 1PW

salesemailweb


36


Step 1. Select “Administrator > M2M Settings” to enter the SNMP settings.

Figure 29. M2M access settings

M2M Settings







Berkshire RG7 1PW

salesemailweb


37


Step 1. Select “Administrator > Logging” to enter the logging settings. Here you can select the save path for any backed up configurations. (Local or remote server)

Figure 30. Log settings

Logging Settings







Berkshire RG7 1PW

salesemailweb


38


Step 1. Select “Administrator > Upgrade” to enter the upgrade firmware settings.

NOTE - When upgrading the firmware, do not remove power.

Figure 31. Upgrade firmware settings

Upgrade Settings


Step 1. Select “Administrator > Reboot” to reboot the router. A popup will appear, prompting ‘YES’ or ‘NO’ to continue with the reboot.

Step 2: If you select ‘YES’, the system will reboot. All relevant firmware upgrades will be effective after the reboot.

System Reboot






Berkshire RG7 1PW

salesemailweb


39


Step 1. Select “Debugging > Logs” to enter the log settings.

Figure 32. Log settings

Logs Settings


Debugging



Figure 3-26 Logs GUI

Step 2 After configure, please click “Save” to finish.

----End

3.7.2 Ping Setting Step 1 Please click “Debugging>Logs” to check and modify relevant parameter.

Figure 3-27 Ping GUI


----End

3.7.3 Trace Setting Step 1 Please click “Debugging>Trace” to check and modify relevant parameter.

Step 1. Select “Debugging > Ping” to enter the ping settings.

Figure 33. Ping settings

Ping Settings




Figure 3-26 Logs GUI


----End

3.7.2 Ping Setting Step 1 Please click “Debugging>Logs” to check and modify relevant parameter.

Figure 3-27 Ping GUI


----End

3.7.3 Trace Setting Step 1 Please click “Debugging>Trace” to check and modify relevant parameter.






Berkshire RG7 1PW

salesemailweb


40


If you want to restore factory settings on your router, this can be done on the web interface by selecting “Administration > Configuration”. Select “Restore Configuration” this will restore your router to it factory settings.

Restore Factory Settings

Figure 34. Restore configuration

Click here to restore factory settings

Via Web Interface






Berkshire RG7 1PW

salesemailweb


41


To restore the routers factory settings, press and hold the reset button on the router located near the power connector. Press and hold the reset button for at least 5 seconds, this can be done when the router is either in use or turned on. Reset is successful when the NET light stops blinking. The router will now be restored to factory settings.

Figure 35. Reset button on router

Via Router

Reset button

Parameter Default settings

LAN IP 192.168.1.1

LAN Subnet Mask 255.255.255.0

DHCP server Enable

User Name admin

Password admin

Table 18. Factory settings






Berkshire RG7 1PW

salesemailweb


42


Appendix (For advanced optional features ONLY)

Step 1. Select “Advanced Network > GPS” to enter the GPS settings.

Figure 36. GPS settings

GPS Settings


Bind Port Local port for GPS data.

Server IP and Port GPS server IP address and port.

Socket type GPS data protocol.

Socket TimeoutThe timeout for socket connection. If socket is not established, it will reconnect after the timeout time.

Serial TimeoutThe time is defined by serial port buffer. After the time, router will send GPS to server.

Packet Payload The max packet for GPS data.

Table 19. GPS settings






Berkshire RG7 1PW

salesemailweb


43




Heart-Beat Content GPS heart beat packet.

Heart-Beat Interval The heart beat packet interval.

Table 19 (continued). GPS settings

NOTE - GPS data format: dtu.heartbeat.content,gps_date, gps_time, gps_use, gps_latitude, gps_NS, gps_longitude, gps_EW, gps_speed, gps_degrees, gps_FS, gps_HDOP, gps_MSL

e.g. Router_00001,083238,120313,12,2230.31563,N,11355.02863,E






Berkshire RG7 1PW

salesemailweb


44


The information contained in this document is proprietary to Siretta. Siretta has made every effort to ensure that the accuracy of the information contained within this document is accurate. Siretta does not make any warranty as to the information contained within this document and does not accept any liability for any injury, loss or damage of any kind incurred by the use of this information.

Siretta does not take responsibility for any application developed using the router characterized in this document and notes that any application of this router must comply with the safety standards of the applicable country and comply with the relevant wiring rules. Siretta reserves the right to make modifications, additions and deletions to this document due to typographical errors, inaccurate information, or improvements to equipment at any time and without notice. Such changes will be incorporated into new editions of this document.

All rights reserved.

© 2019 Siretta Ltd

Disclaimer






Berkshire RG7 1PW

salesemailweb


45


DefinitionsTerm Definition

3G 3rd Generation Mobile Telecommunications

4G 4th Generation Mobile Telecommunications

APN Access Point Name

DDNS Dynamic Domain Name System

DHCP Dynamic Host Configuration Protocol

DI Direct Input

DMZ Demilitarized Zone

DNS Domain Name System

DO Direct Output

GND Ground

GPS Global Positioning System

GUI Graphical User Interface

I/O Input/Output

ICMP Internet Control Message Protocol

IP Internet Protocol

ISP Internet Service Provider

LAN Local Area Network

LTE Long-Term Evolution

M2M Machine to Machine

MPPE Microsoft Point-to-Point Encryption

NAT Network Address Translation

NTP Network Time Protocol

PMP Port Mapping Protocol

SIM Subscriber Identity Module

SMS Short Message Service

SNMP Simple Network Management Protocol

TCP Transmission Control Protocol

UDP User Datagram Protocol

UMTS Universal Mobile Telecommunications System

UPnP Universal Plug and Play

VPN Virtual Private Network

WAN Wide Area Network

WLAN Wireless Local Area Network



Siretta LtdBasingstoke RoadSpencers WoodReadingBerkshireRG7 1PWUnited Kingdom

salesemail

Company No. 08405712VAT Registration No. GB163 04 0349

+44 (0)118 976 [email protected]

www.siretta.com

Rev 1.1 - March 2020

quartz-lite software manual

Documents