quickguide vd4000 1 engba01-wz1181.ktics.co.kr/quickguide_vd3000_eng.pdf · connect the power cable...

2
Quick Guide www.visiondrive.co.kr Installation & Use WARNING Until the initial boot is up or the upgrade patch is fully installed, do not turn on or off the power source, for this may disengage the power source and effect the booting process. This product only works with the Vision Drive SD cards. Only use the enclosed cable to connect your product. Clean any impurities on the area of installation or any other area where the camera will be positioned. While the black box is in operation, do not remove the SD card. Operate the product manually when the vehicle is parked in a safe place. For disassembling, turn off the power completely before proceeding. Do not disassemble, remodel or repair the product. Product Installation Connect the bracket and the unit Insert the SD card Connect the cable to the unit and Connect to cigar jack Turning it on and setting Check LED lamps Organize the cable line attach to the windshield Place the bracket into the slot then slide to the left to click on. Insert the SD card into the SD card slot on the side of the unit. Insert the adaptor into the cigar jack. The REC lamp will blink blue for normal recording. In a case of an impact, the lamp will change to a red blinking light. The GPS lamp will be red if not connected and will turn blue when it is. The connection time differs depending on where the vehicle is located. Use the enclosed cable holders to organize the cable line. Insert the key in to the ignition and then slightly/fully turn the key to give power to the cigar jack outlet. A voice notification will alarm and the LED lights will blink to let you know that the system is fully on. Connect the power cable and then remove the sticker cover. Place the unit on the area where you have cleaned for any impurities. Place the unit close to the mid section of the vehicle. the camera angle

Upload: others

Post on 20-Aug-2020

3 views

Category:

Documents


0 download

TRANSCRIPT

Page 1: QuickGuide VD4000 1 engba01-wz1181.ktics.co.kr/QuickGuide_VD3000_eng.pdf · Connect the power cable and then remove the sticker cover. Place the unit on the area where you have cleaned

�Q�u�i�c�k� �G�u�i�d�e

�w�w�w�.�v�i�s�i�o�n�d�r�i�v�e�.�c�o�.�k�r

Installation & Use

WARNINGUntil the initial boot is up or the upgrade patch is fully installed,do not turn on or o� the power source, for this may disengagethe power source and e�ect the booting process.This product only works with the Vision Drive SD cards.Only use the enclosed cable to connect your product.Clean any impurities on the area of installation or any other area where the camera will be positioned.While the black box is in operation, do not remove the SD card.Operate the product manually when the vehicle is parked in a safe place.For disassembling, turn o� the power completely before proceeding.Do not disassemble, remodel or repair the product.

Product Installation

Connect the bracket and the unit

Insert the SD card

Connect the cable to the unit and

Connect to cigar jack

Turning it on and setting

Check LED lamps

Organize the cable line

attach to the windshield

Place the bracket into the slot then slide to the left to click on.

Insert the SD card into the SD card slot on the side of the unit.

Insert the adaptor into the cigar jack.

The REC lamp will blink blue for normal recording.In a case of an impact, the lamp will change to a red blinking light.The GPS lamp will be red if not connected and will turn bluewhen it is. The connection time di�ers depending on where thevehicle is located.

Use the enclosed cable holders to organize the cable line.

Insert the key in to the ignition and then slightly/fully turn the keyto give power to the cigar jack outlet. A voice noti�cation willalarm and the LED lights will blink to let you know that thesystem is fully on.

Connect the power cable and then remove the sticker cover. Place the unit on the area where you have cleaned for anyimpurities. Place the unit close to the mid section of the vehicle.

the camera angle

Page 2: QuickGuide VD4000 1 engba01-wz1181.ktics.co.kr/QuickGuide_VD3000_eng.pdf · Connect the power cable and then remove the sticker cover. Place the unit on the area where you have cleaned