radio study material

8/16/2019 Radio Study Material

1/21

FIX FREQUENCY OPERATIONS FOR AN/PRC-150EITHER FIXED FREQUENCY OR ALE RADIO OPERATIONS BEGIN WITH THE PRESETS.

ON THE KDU PRESS PRF (#8 BUTTON)

SELECT MODE

SELECT PRESET SELECT CHANNEL

THE KDU DISPLAYS CHANNEL NUMBER TO CHANGE: ENTER THE NUMBER OF THE FIRST UNUSED CHANNEL (NORMALLY00) AND PRESS ENTER.

ENTER RECEI!E FREQUENCY (RX FREQUENCY) AND PRESS ENTER.

THE SAME FREQ YOU ENTERED FOR RECEI!E SHOULD BE DISPLAYED FOR TRANSMIT (TX FREQUENCY) SO PRESSENT.

MODULATION IS ALWAYS USB FOR USMC HF RADIO COMMUNICATIONS.

PRESS ENTER AT THE AGC SPEED CHOOSING THE DEFAULT AT IF BANDWIDTH PRESS THE DOWN BUTTON ONCE FOR".KH$ AND PRESS ENT.

RX ONLY IS NO% LIMIT MAX TX POWER IS NO% ENABLE HAIL TX IS NO% ENABLE SSB SCAN IS YES.

YOU ARE NOW BACK AT THE CHANNEL NUMBER TO CHANGE: SCREEN& ENTER THE NEXT A!AILABLE NUMBER ANDREPEAT THE PRE!IOUS STEPS UNTIL ALL OF YOUR FREQUENCIES HA!E BEEN ENTERED

ONCE ALL OF YOUR A!AILABLE FREQUENCY HA!E BEEN ENTERED PRESS CLR (') TIMES TO REACH THE MAINSCREEN.

OPERATIONS

PRESS THE (MODE) BUTTON TO SCROLL THROUGH THE A!AILABLE OPERATING MODES. CHOICES ARE: FIX& ALE& HOP& G. PRESS(MODE) UNTIL FIX IS DISPLAYED.

PRESS (ENT) TO SELECT FIX MODE.

PRESS LEFT AND RIGHT BUTTONS UNTIL CH000 IS HIGHLIGHTED. PRESS (ENT).

USE THE UP AND DOWN BUTTONS TO SELECT A CHANNEL. PRESS (ENT).OR PRESS THE RE!ERSE KEY TO ACCESS THE ALTERNATE SCREEN. HERE YOU CAN PRESS THE PRE BUTTON TO SCROLL THROUGH YOUPRESETS.HOW TO LOAD THE PRC-150 WITH CRYPTO

PLACE THE FUNCTION KNOB ON LD PRESS THE DOWN ARROW TO KYK PRESS ENTER. CRYPTO TYPE: AND!T PRESS ENTER

KEY TYPE: TEK PRESS ENTER. KEY NUMBER: 0 PRESS ENTER

SETTING UP THE CYZ-10

PRESS THE ON*OFF BUTTON SELECT APPL PRESS ENTER

SELECT RADIO PRESS ENTER

ARROW O!ER AND DOWN TO COMSEC PRESS ENTER.

ARROW O!ER TO LD AND PRESS ENTER.

PAGE DOWN UNTIL YOU SEE THE HF FILL PRESS ENTER. (XMT SHOULD APPEAR IN THE LOWER RIGHT HANDCORNER.)

ARROW O!ER TO QUIT PRESS ENTER. PRESS ENTER.

PRESS ENTER ON RT.SELECT ENCRYPTION KEY

AT THE PRESET SCREEN& PRESS RIGHT OR LEFT BUTTONS UNTIL THE KEY FIELD IS HIGHLIGHTED. NOTE: THE CHARACTERS++ IN THE KEY FIELD INDICATE THAT NO KEY IS CURRENTLY SELECTED.PRESS (S) UP KEY TO SCROLL TO THE DESIRED FILL WHICH SHOULD READ TEK0 AND HA!E AND!THF IN SMALL LETTERS BELOWIT.PRESS (ENT) TO SELECT THE DISPLAYED KEY.YOU,LL BE ASKED CHANGE CRYPTO MODE- SELECT YES.THE CRYPTO FILLS ARE READY FOR USE.PROGRAMMING THE PRC-150 TOD SETTINGS

PLACE THE FUNCTION KNOB ON CT.

PRESS THE PGM BUTTON.

PRESS THE ARROW BUTTON UNTIL YOU GET TO CONFIG.

THEN USE THE ARROWS TO SCROLL TO TOD UTC OFFSET 00:00 PRESS ENTER.

LEAP SECONDS / PRESS ENTER DATE FORMAT YYYYMMDD PRESS ENTER.

NEW DATE: SET DATE OFF PSN PRESS ENTER TIME FORMAT "'HR PRESS ENTER.

NEW TOD: SET TIME OFF PSN PRESS ENTER

PRESS CLR TWICE.

1


2/21

HOW TO SET THE PRC-150 DATA SETTING

TURN THE RADIO TO THE PT SETTING.

PRESS THE PGM BUTTON.

PRESS THE ARROW BUTTON UNTIL YOU GET TO CONFIG. THEN USE THE ARROWS TO SCROLL TO PORTS.

SCROLL TO ASCII AND PRESS ENTER. IT SHOULD HA!E NUMBER !ALUE SUCH AS /."K OR /.K.

SCROLL TO /.K AND PRESS ENTER

PRESS ENTER UNTIL YOU GET BACK TO THE SCREEN WITH ASCII AND PRESS CLR BUTTON THREE TIMES.SETTING THE BROADCAST FOR THE TOD SERVER

PRESS THE PGM BUTTON

ARROW O!ER TO SCHED PRESS ENTER.

SELECT ADD PRESS ENTER.

OFFSET TIME: 00:00 PRESS ENTER

INTER!AL TIME: (SET THE TIME YOU WANT THE TOD SER!ER TO BROADCAST. EX. 0:00 IS ONE HOUR.)SETTING UP TAC-CHAT FOR PRC-150

INSTALL THE RPA INTO THE PRC/0

LOAD CRYPTO PLACE THE FUNCTION KNOB ON LD

PRESS THE DOWN ARROW TO KYK PRESS ENTER

CRYPTO TYPE: AND!T PRESS ENTER.

KEY TYPE: TEK PRESS ENTER

KEY NUMBER: 0 PRESS ENTERSETTING UP THE CYZ-10

PRESS THE ON*OFF BUTTON.

SELECT APPL PRESS ENTER.

SELECT RADIO PRESS ENTER.

ARROW O!ER TO LD AND PRESS ENTER

PAGE DOWN UNTIL YOU SEE THE HF FILL PRESS ENTER. (XMT SHOULD APPEAR IN THE LOWER RIGHT HANDCORNER.)

ARROW O!ER TO QUIT PRESS ENTER.

PRESS ENTER.

PRESS ENTER ON RT.LOAD TIMING

PLACE THE FUNCTION KNOB ON CT

PRESS THE PGM BUTTON

PRESS THE ARROW BUTTON UNTIL YOU GET TO CONFIG

THEN USE THE ARROWS TO SCROLL TO TOD

UTC OFFSET 00:00 PRESS ENTER LEAP SECONDS / PRESS ENTER

DATE FORMAT YYYYMMDD PRESS ENTER NEW DATE: SET DATE OFF PSN PRESS ENTER.

TIME FORMAT "'HR PRESS ENTER NEW TOD: SET TIME OFF PSN PRESS ENTER

PRESS CLR TWICE.SET DATA SETTINGS

PRESS THE PGM

PRESS THE ARROW BUTTON UNTIL YOU GET TO CONFIG.

THEN USE THE ARROWS TO SCROLL TO PORTS

SCROLL TO ASCII AND PRESS ENTER

IT SHOULD HA!E A NUMBER !ALUE SUCH AS /."K OR /.K

SCROLL TO /.K AND PRESS ENTER PRESS ENTER UNTIL YOU GET BACK TO THE SCREEN WITH ASCII AND PRESS CLR TIME

2


3/21

SETTING UP ALE FOR PRC-150

PRESS (8) PGM SELECT MODE

SELECT PRESET SELECT CHANNEL

ENTER CHANNEL NUMBER TO BE MODIFIED PRESS ENTER

ENTER FREQUENCY FOR THE CHANNEL

REPEAT UNTIL ALL CHANNELS ARE PROGRAMMED

AFTER ALL CHANNELS ARE PROGRAMMED PRESS CLEAR TWICE

SELE!T ALE

PRESS ENTER

SLECT CHAN1GROUP

SELECT ADD ADD A CHANNEL GROUP (00)

SCREEN WILL CHANGE SELECT ADD

ADD THE CHANNELS PROGRAMMED ABO!E2PRESS CLR () TIMES SELECT ADDRESS

SELF ADDRESS

SELECT ADD

ADD YOUR SELF ADDRESS

SELECT THE CHANNEL SELECT THE CHANNEL GROUP

PRESS ENTER

PRESS DOWN ARROW

SELECT INDI!IDUAL ADDRESS (NAME YOURSELF) PRESS ADDRESS OF A STATION ON THE NET

PRESS ENT ENTER CHANNEL GROUP TO BE USED

PRESS ENT

AT ASSOC SELF (PRESS ENT ON YOUR ADDRESS)

REPEAT UNTIL ALL ADRESSES IS ADDED

SELECT NET ADDRESS

ENTER NAME OF NET

PRESS ENT

ENTER CHANNEL GROUP TO BE USED

PRESS ENTER

AT ASSOC SELF YOU,LL FIND YOUR STATION NAME AND PRESS ENTER PRESS ENTER ON ADD

ADD ALL NET MEMBERS CLEAR OUT THE MAIN SCREEN

PRESS MODE () UNTIL IT READS ALE

PRESS ENTER

PRESS CALL () AND SELECT STATION

PRESS ENTER

WAIT TO LINK

3


4/21

DAMA SETTINGS FOR THE PRC-11LOADING CRYPTO ONTO THE PRC FOR DAMARADIO

TURN RADIO TO LD ARROW DOWN TO KYK& THEN PRESS ENTER

ARROW DOWN TO SATELLITE& THEN PRESS ENTER KEY TYPE: TSK& KEY NUMBER:0& THEN PRESS ENTER

STOP ON THE SCREEN THAT SAYS PRESS ENTER TO INTIATECYZ-10

TURN CY$0 ON ONCE ON& TURN LOCK LTR OFF& LOCATED ON THE BOTTOM LEFT OF CY$0

ON MAIN SCREEN OF CY$0& SELECT APPL& THEN PRESS ENT

NEXT SCREEN& SELECT RADIO& THEN PRESS ENTER

CY$0 WILL SAY LOADING APPLICATIONS

ON THE NEXT SCREEN SELECT COMSE& THEN PRESS ENTER NEXT SELECT LD& THEN PRESS ENTER

SELECT TEK& THEN PRESS ENTER PRESS THE P DN*H BUTTONS UNTIL YOU FIND THE DAMA KEY& THEN PRESS ENTER& YOU,LL SEE XMT ON THE

BUTTOM RIGHT& PRESS THE RIGHT ARROW TO QUIT& THEN PRESS ENTER AGAIN NEXT SCREEN WILL SAY CONNECT TO ANCD TO RT& PRESS ENTER

THE NEXT SCREEN WILL SAY SENDING TEK DAMA AND THE DATE THAT YOU NEED

NEXT SCREEN WILL SAY PRESS LOAD ON RT& PRESS ENTER ON THE PRCRADIO

SCREEN WILL SAY FILL DONE PRESS ANY KEY& PRESS ENTER

FILL MORE DATA- YES& PRESS ENTER

NEXT SCREEN PUSH CLEAR

CRYPTO TYPE: SELECT AND!T& PRESS ENTER KEY TYPE: TEK& KEY NUMBER:0& THE PRESS ENTER

STOP ON THE SCREEN THAT SAYS PRESS ENTER TO INITATECYZ-10

SELECT COMSEC& THEN PRESS ENTER

NEXT SELECT LD& THEN PRESS ENTER

SELECT TEK& THEN PRESS ENTER

PRESS THE P DN*H BUTTON UNTIL YOU FIND THE HF KEY& THEN PRESS ENTER& YOU,LL SEE XMT ON THE BOTTOMRIGHT& PRESS THE RIGHT ARROW TO QUIT& THEN PRESS ENTER AGAIN

NEXT SCREEN WILL SAY CONNECT TO ANCD TO RT& PRESS ENTER

THE NEXT SCREEN WILL SAY SENDING TEK HF AND THE DATE THAT YOU NEED

NEXT SCREEN WILL SAY PRESS LOAD ON RT& PRESS ENTER ON THE PRCRADIO

SCREEN WILL SAY FILL DONE PRESS ANY KEY& PRESS ENTER

MORE FILL DATA- NO& PRESS ENTER SWITCH THE FUNCTION KNOB TO CT PRESS 8*PGM

SELECT DAMA& THEN PRESS ENTER

SELECT NETS& THEN PRESS ENTER

SELECT NET TO MODIFYSELECT THE CHANNEL YOU WANT TO USE FOR DAMA& THEN PRESS ENTER

SELECT CHANNEL& PRESS ENTER& CHANNEL NUMBER WILL !ARY ACCORDING TO YOUR SAA & PRESS ENTER

TRANSMIT CAPABAILITY FULL& PRESS ENTER

CONSTANT KEY PORT NO& PRESS ENTER

DAMA CONFIG IS THE CHANNEL YOU WANT TO USE FOR DAMA& PRESS ENTER RANGING ACTI!E& PRESS ENTER

ADDR& PRESS ENTER SELECT BASE1ADDRESS WHICH IS YOUR TBA& REFER TO SAA

SELECT GUARDLIST& PRESS ENTER SELECT ADD& PRESS ENTER& REFER TO SAA& THE NUMBER WILL USUALLY START WITH A ()

AFTER ADDING YOUR GUARD ADDRESS& PRESS CLEAR TWO TIMES

SELECT TRANSEC& PRESS ENTER ORDERWIRE ENCRYPTIONON& PRESS ENTER

KEY LOCATION NEEDS TO SAY TSK 0& PRESS ENTER

KEY LOCATION " ALSO NEEDS TO SAY TSK 0& YOU NEED TO ENSURE THAT YOU HA!E TSK 0 IN ALL KEYLOCATIONS& THEN PRESS ENTER

POWER MAKE SURE IT IS ON THE HIGHEST SETTING& NAMEYOU CAN CHANGE IF YOU WANT

PUSH CLEAR ONE TIME& THEN GO TO PORT1CONFIGS& PRESS ENTER SELECT PORT CONFIGONCE AGAIN IS THE CHANNEL YOU CHOSE TO MODIFY& PRESS ENTER

COMSEC& PRESS ENTER SELECT CRYPTO MODEAND!T& PRESS ENTER,ENCRYPTION KEYTEK 0& PRESS ENTER

TRAINING FRAME "0& PRESS ENTER

4


5/21

!OICE AUTO SWITCHDISABLED& PRESS ENTER

DATA*!OC& PRESS ENTER

!OICE MODE LPC& PRESS ENTER SYNC*ASYNC& PRESS ENTER& SYNC& PRESS ENTER

BAUD RATE "'00& PRESS ENTER DATA OPTIONS NUMBER00& PRESS ENTER

CONFIG1CODE& PRESS ENTER "/KH$ PORTS CFG CODE00 PRESS ENTER

/KH$ PORTS CFG CODE00 PRESS ENTER

PRESS CLEAR ONE TIME& GO TO DESTINATIONS& PRESS ENTER

ONCE AGAIN SELECT THE CHANNEL YOU WANT TO USE FOR DAMA& PRESS ENTER

SELECT "/K1AC& PRESS ENTER

ADD& PRESS ENTER

DESTINATIONS TO ADD ENTER YOUR GUARD ADDRESS FROM EARLIER& PRESS ENTER

PRESS CLEAR SIX TIMES& UNTIL YOU GET TO THE MAIN SCREEN PRESS NUMBER *MODE

OPERATION MODE SELECT DAMA& THEN PRESS ENTER& WAIT FOR IT TO CONFIGURE& ONCE DAMA IS CONFIGURED&CONNECT THE RF CABLE FROM THE SATCOM ANTENNA TO THE !HF HI*UHF PORT

AIM THE SATCOM ANTENNA TO THE DESIGNATED A$IMUTH AND DEGREES ON YOUR SAA

RADIO WILL SAY AQUIRING

SATELLITE SHOULD ACQUIRE AUTOMATICALLY

ONCE CONNECTED& PRESS 0 FOUR TIMES& THIS SCREEN WILL TELL YOU IF YOUR CONNECTED ACTI!ELY OR IDLECONNECTED. YOU WANT TO BE IDLE UNTIL READY TO CALL.

TO PLACE A CALL PRESS NUMBER *CALL

SELECT REQUEST TYPE PLACE A CALL& PRESS ENTER

SELECT DESTINATION IT WILL SHOW YOU YOUR CHANNEL NUMBER AND NAME& PRESS ENTER

SELECT PRECEDENCE ROUTINE

DURATION 0000MIN& PRESS ENTER MAIN SCREEN& PENDING CONNECTED& IT WILL BEGIN TO PLACE YOUR CALL AUTOMATICALLY& ONCE CONNECTED

IT,LL SAY ACTI!E CONNECTED& PROCEED TO COMMUNICATE.FREQ-HOP SETUP FOR 11

LOAD COMSEC TEKS (!INSON) AND SINCGARS FH DATA BOTH SHOULD BE PRESENT IN CY$0& SO BOTH CAN BELOADED AT THE SAME TIME

PLACE THE FUNCTION KNOB ON THE AN*PRC TO LD

ON THE KDU ARROW TO CY$0 RDS AND PRESS ENTER,

THE KDU WILL DISPLAY PRESS ENTER TO INITIATE& PRESS ENTER

THE KDU WILL DISPLAY FILL IN PROGRESS& AT THIS POINT LEA!E THE KDU ALONE

CONNECT THE CY$0 TO THE RT

ONCE THE CY$0 IS RUNNING ENSURE THE LOCKLTR IS TURNED OFF

WITH APPL HIGHLIGHTED PRESS ENTER ARROW TO RADIO AND PRESS ENTER

WITH SEND HIGHLIGHTED PRESS ENTER SEND TO: WITH RADIO HIGHLIGHTED PRESS ENTER

SELECT: WITH ICOM HIGHLIGHTED PRESS ENTER THE CY$0 WILL SAY + CONNECT TO RT AUD*FILL CONNECTOR3 PRESS ENTER

PRESS ENTER AGAIN

+DO YOU WANT TO INCLUDE TIME-3 WITH THE N HIGHLIGHTED PRESS ENTER

THE CY$0 WILL BEGIN TO FILL THE RT

THE CY$0 WILL DISPLAY ICOM TRANSFER SUCCESSFUL BUT DO NOT TOUCH ANYTHING.

AN*PRC IS STILL USING THE CY$0 TO FINISH THE TRANSFER

ONCE THE KDU DISPLAYS FILL DONE PRESS ANY KEY PRESS ENTER

FILL MORE DATA- PRESS YES SELECT KYK

ENTER TEK 04 SCREEN WILL SAY PRESS ENTER INITIATE

ON CY$0 SELECT COMSEC PRESS ENTER

SELECT LD& PRESS ENTER

PG DN TO SELECT !HF KEY& PRESS ENTERFREQ-HOP PROGRAMMING FOR AN/PRC-11

ST COPY A HOPSET INTO OUR DESIRED NET SLOT

PRESS 8*PGMTHEN SELECT NORMSELECT GENERAL

HOPPING TYPE IS SINCGARS

SELECT HOPSET1COPY

HOPSET COMPARTMENT COPY FROM: "/ TO HOPSET COMPARTMENT:0 COPY AS HOPSET ID F ENTER (NET ID) AND PRESS ENT

THE HOPSET IS COPIED AND YOU GO TO THE SUB MENU. PRESS CLR. ARROW TO NET AND PRESS ENT

SELECT NET TO MODIFY& AND PRESS ENT

NET TYPE IS FREQUENCY HOPPING

5


6/21

HOPPING TYPE IS SINCGARS

SELECT HOPSETHOPSET COMPARTMENT ENTER 0 AND PRESS ENTER

LATE NET ENTRY IS OFFRECEI!E ONLY IS NO YOU ARE AT THE SUBMENU

ARROW TO COMSEC AND PRESS ENTCRYPTO MODE IS !INSON ENCRYPTION KEY IS TEK0 5ANALOG DATA IS NO

YOU ARE BACK AT THE SUB MENU THE SETTINGS FOR DATA*!OC ARE DEFAULTED TO THE PROPER SETTINGS

ARROW TO POWER AND PRESS ENTERSELECT THE PROPER POWER OUT

YOU SHOULD BE AT THE SUB MENU ARROW TO NAME AND PRESS ENTER

ARROW TO NAME AND PRESS ENTER

ENTER DESIRED NAMEPRESS ENTER TO ENTER TO SUB MENU PRESS CLR () TIMES

AT THE MAIN SCREEN PRESS THE SIDE OF THE PRE BUTTON UNTIL NET 0/ IS DISPLAYED

PRESS THE OPT (#)

ARROW O!ER TO TIME AND PRESS ENTER WITH GTOD FLASHING PRESS ENT SETTING THE GTOD: ENTER THE PROPER SINCGARS 6ULIAN DATE

ARROW TO THE TIME AND ENTER THE HOUR IN $ULU TIE ARROW TO MINUTES AND ENTER THE MINUTES FROM $ULU TIMEPRESS ENT TWICE

YOU SHOULD NOW BE BACK AT THE GTOD TIME SCREEN !ERIFY YOUR RADIO MATCHES $ULU TIME OR IN OUR CASE ALL THE RADIOS SHOW THE SAME TIME

PRESS CLR THREE () TIMES TO GET BACK TO THE MAIN SCREEN

WE NOW HA!E OUR FIRST FRENQUENCY HOPPING SINCGARS NET READY TO GO.SATCOM CRYPTO LOADING FOR AN/PRC 11

PROCEDURES

PLACE RT MODE SWITCH TO LD

ON KDU CHOOSE KYK FOR FILL DE!ICE AND PRESS ENTER

CHOOSE SATELLITE FOR CRYPTO TYPE AND PRESS ENTER

KEY TYPE IS TSK AND KEY NUM IS 0 KDU DISPLAYS PRESS ENTER TO INITIATE7 DO NOT INITATE YET7 TURN CY$0 ON AND CONNECT RTENSURE LOCK LTR IS OFF WITH APPL HIGHLIGHTED PRESS ENT

ARROW O!ER TO RADIO AND PRESS ENTER ARROW TO COMSEC AND PRESS ENTERARROW TO LD AND PRESS ENTER

WITH TEK HIGHLIGHTED PRESS ENTER4 SELECT KEY SHOULD BE HIGHLIGHTED WITH THE WORD QUIT NEXT TO IT AND AKAT //" LISTED BELOW

IT. IF AKAT //" IS NOT DISPLAYED THEN PRESS P DN KEY UNTIL IT IS LISTED AND THEN PRESSENTER.

XMT WILL APPEARIN THE BOTTOM RIGHT CORNER OF THE CY$0& ARROW O!ER TO QUIT AND PRESS ENTER

THE CY$0 WILL DISPLAY CONNECT ANCD TO RT& WHICH YOU HA!E ALREADY DONE SO PRESS ENTER

A QUICK MESSAGE IS DISPLAYED AND THEN PRESS (LOAD) ON RT IS DISPLAYED

AT THIS TIME PRESS ENT ON THE KDU ON RT FILL IN PROGRESS IS DISPLAYED ON THE KDU AND THEN FILL DONE& PRESS ANY KEY IS DISPLAYED PRESS

ENTER MORE FILL DATA- IS DISPLAYED ON THE KDU SELECT YES AND PRESS ENTER

ON THE KDU PRESS CLR CRYPTO TYPE IS AND!T& PRESS ENT KEY TYPE IS TEK AND KEY NUMBER IS 0"

KEY TYPE IS TEK AND KEY NUMBER IS 0"

ON CY$0 ARROW TO LD AND PRESS ENTERWITH TEK HIGHLIGHTED PRESS ENTER

XMT WILL APPEAR IN THE BOTTOM RIGHT CORNER OF THE CY$0& ARROW O!ER TO QUIT AND PRESS ENTER

THE CY$0 WILL DISPLAY CONNECT ANCD TO RT& WHICH YOU HA!E ALREADY DONE SO PRESS ENTER

A QUICK MESSAGE IS DISPLAYED AND THEN PRESS (LOAD) ON RT IS DISPLAYED

AT THIS TIME PRESS ENTER ON THE KDU OF THE RT FILL IN PROGRESS IS DISPLAYED ON THE KDU AND THEN FILL DONE& PRESS ANY KEY IS DISPLAYED

MORE FILL DATA- IS DISPLAYED ON THE KDU SELECT NO AND PRESS ENTER PLACE MODE TO CT4 YOUR !INSON CRYPTO IS NOW LOADED IN TO TEK NUM 0& YOUR AND!T IS LOADED IN TEK NUM 0"& AND YOUR

SATELLITE IS TSK NUM 0. REMEMBER THIS IS IT IMPORTANT YOU WILL NEED THIS INFO LATER

6


7/21


8/21

PRC-11 SINGLE CHANNEL-PROGRAMMING

ON KDU PRESS 8*PGM SELECT NORMSELECT NETSELECT NET TO MODIFY

ACTI!ATE IN LIST- YES

NET TYPELOS FIX FREQUENCY RECEI!E AND TRANSMIT FREQUENCY (THE FREQUENCIES WILL BE THE SAME)

RECEI!E ONLYNO4 RADIO WILL NOT ALLOW ENTRY OF FREQUENCIES OUTSIDE RANGE 0MH$/"MH$

ARROW O!ER TO COMSEC AND PRESS ENTERCRYPTO MODE (!INSON) PRESS ENTER

ENCRYPTION KEY 5TEK0 5ANALOG DATA IS NO

AND YOU HA!E RETURNED TO THE SUB MENU SHOWN ABO!E THERE ARE NO ENTRIES REQUIRED FOR DATA*!OICEFOR FM NETS

FOR AM NETS YOU MUST SELECT DATA*!OICE PRESS ENTER

PRESS ENTER FOR DATA*!OICE WITH AUTO ON OFF PORT FLASHING WITH MODULATION DISPLAYED ARROW TO AM PRESS ENT

CHANNEL SPACING IS "/KH$& SYNC*ASYNC IS SYNC

SQUELCH IS OFFANALOG SQUELCH TYPE TO TONE PRESS ENTER

AT SUB MENU CHOOSE POWER AT 0WATTS AND PRESS ENTER

AT SUB MENU CHOOSE NAMECLEARING AND ZEROIZING THE AN/PRC 11

TO $ERO ONLY THE COMSEC DATA USE $ALL TO $ERO COMSEC AND ALL PROGRAMMING PARAMETERS $ERO KEY AND CLR

PRC-15" FREQ HOPPING

FUNCTION KNOB TO FPPRESS 8*PGM PRESS ENTER ON SYSTEM PRESETSENTER ON SYSTEM PRESETS CONFIG

SELECT CHANNEL YOU WANT TO MODIFY PRESS ENTER ON PRESET DESCRIPTION

SELECT SINCGARS FOR YOUR PRESET WA!EFORM

SELECT FREQUENCY HOPPING FOR OPMODE

SELECT NAME FO CHANNEL

CRYPTO KEY TEK0TX POWER LE!EL HIGHTRAFFIC !OICE MODE !OICE

HOPSET COMPARTMENT

SC FREQUENCY LEA!E DEFAULT 5SC SQUELCH TYPETONE

CLEAR OUT TO MAIN SCREEN USING PRESET BUTTON SCROLL TO THE CHANNEL YOU MODIFIED USING YOUR RIGHT ARROW SCROLL TO NET ID

CHANGE NET ID USING KEY PAD PRESS ENTERSETTING TIME

*OPTSELECT SINCGARS OPTIONSSINCGARS GTODUSER ENTRYTIME

8


9/21

PRC-15" SC PT

TURN FUNCTION KNOB TO FPPRESS 8*PGM PRESS ENT ON SYSTEM PRESETSPRESS ENT ON SYSTEM CONFIG

SELECT THE CHANNEL YOU WANT TO MODIFYPRESS ENT ON PRESET DESCRIPTION SELECT !ULOS FOR PRESET WA!EFORMHIT ENT ON GENERAL CONFIG

NAME THE CHANNEL YOU WANTPRESET TYPE WILL BE LOS

ENTER DESIGNATED FREQ&PRESS ENTRECEI!E ONLY IS NO

TX FREQ USE RX FREQSCROLL TO COMSECCRYPTO MODE 5NONE

SCROLL TO TRAFFICTRAFFIC MODE IS CLEAR

MODULATION TYPE (DEPENDS ON FREQ AM OR FM) FM DE!IATION IS ./TX POWER LE!EL SHOULD BE HIGH

SCROLL TO SQUELCHSQUELCH SET TO NOISE FM TRANSMIT TONEENABLED

CLR TO MAIN MENUUSING PRESET BUTTOM ENABLED SCROLL TO CHANNEL YOU MODIFIEDPROGRAMMING PRC-15#

OPEN ASTRO "/ PORTABLE CPS

CONNECT THE PROGRAMMING CABLE TO THE PRC / AND THE USB CABLE TO THE LAPTOP

TURN ON PRC/

ON ASTRO "/ GO TO FILE 5 THEN READ DE!ICE

UNDER SELECT PORTPORT(USB)PRESS OK AT THIS TIME YOU SHOULD HEAR A BEEP NOISE WHICH CONFIRMS THE READING NOW IN YOUR TREE !IEW YOU,LL SEE THE:

4 SERIAL NUMBER (EX.'0CHK")4 RADIO INFORMATION4 RADIO CONFIGURATION4 CON!ENTIONAL4 SCAN4 $ONE CHANNEL ASSIGNMENT

CLICK ON () TO OPEN $ONE CHANNEL ASSIGNMENT4 NOTE:YOU HA!E / POSSIBLE $ONES AND CHANNELS PER $ONE

DOUBLE CLICK ON $ONE CHANNEL ASSIGNMENT YOU CHOOSE TO WORK ON

CLICK ON THE CHANNELS TAB9ALL THE CHANNELS WILL APPEAR4 EDIT CHANNEL NAME BY DOUBLE CLICKING AND ENTER THE NAME (EX.RCTANTHILL)4 RECEI!E FREQUENCY AND TRANSMIT FREQUENCY MUST BE THE SAME (EX.8.8/0)4 CHANGE RECEI!E AND TRANSMIT NETWORK ID (EX.0)

NOTE:ALL NETWORK ID MUST BE DIFFERENT WITH SAME RX*TX FREQUENCIES. ONCE YOU COMPLETE THE INFORMATION FOR THE CHANNELS SA!E THE CODEPLUG GO TO TOOLS

4 CLONING4 CLONING WI$ARD

NOTE:MAKE SURE FOR THE REGULAR /,S ITS CON!ENTIONAL ONLY AND FOR THE XTS"/00 ITS CON!ENTIONAL AND TRUNKING

CLICK NEXT

CLICK PROGRAM

WHEN DONE PROGRAMMING& IT SHOULD SAY +WRITE SUCCESSFUL3

LOADING CRYPTO WITH KVL

PRESS THE POWER BUTTON

TARGET LOAD

KEY AND !ERIFY THE KEY (EX.0'0/) AND PRESS LOAD

AND IT SHOULD SAY +SUCCESSFULLY OK3! NOTE: WHEN CHANGING OUT BATTERIES MAKE SURE RADIO IS OFF BEFORE REMO!ING THE

BATTERY IF NOT YOU,LL LOSE CRYPTO.

9


10/21

DSU TROUBLESHOOTING$

STEP GO TO SER!ICES AND STOP AND RESTART SER!ICES

4 NOTE: ONLY STOP AND RESTART THE (') ACCESS NETS

STEP "RESTART LAPTOP AND GET THE TEMPLATE PUSHED BACK TO YOUR STATION

STEP RESTART NETS COMPLETELY& REINSTALL& DELETE ACCESS POINTS AND SYSTEM CONSOLE FROM DESKTOP

STEP 'SWITCH ALL ANTENNAS FROM THE RADIOS ON DSU TO THE RADIOS BEING REMOTED TO THE COC ANDMONITOR NETS

RESTARTING DSU

MY COMPUTER

CDRI!E POSTINSTALL

DSAN /./.SETUP.EXE (BLUE CONTROL) NEXT CHOOSE DSAN WORKSTATION

DATABASE MESSENGER INSTALL (NO) YES FOR DIRECT X

SELECT SINGLE UAA OPERATOR UA (MAKE SURE OPERATOR )

START SERVICES

START THE PROS BEGIN WITH ACCESS NETS

CLICK ON ACCESS POINTS

START4 RUN4 MSTSC (REMOTE DESKTOP)4 USERNAME(GDA;?


11/21

STARTING DSU

CLICK ON ACCESS POINTS AND THE TEMPLATE WILL OPEN UP

CLICK ON ONCE FOR RXTWICE FOR RX*TX

AD6UST !OLUME4 CLICK ON AUDIO AD6UST AND CLICK ON THE NET YOU WANNA AD6UST4 IN ORDER TO TRANSMIT YOU MUST HA!E THE TX*RX ON

PRC-11HPW-HIGH PERFORMANCE WAVELENGTHREQUIREMENTS FOR OPERATION$COMPUTER MUST HAVE

1% OUTLOOK "00# OR OLDER& ANY GREATER AND IT WILL NOT WORK "% IF THE DATA CABLE DON'T PLUG INTO THE COMPUTER YOU ARE USING THAN YOU MUST USE A USB CABLE

LOADING CRYPTORADIO$

. SWITH THE FUNCTION KNOB TO LD". KYK & KG8'. KYK& SATALITE (TSK)

SKL OR CYZ10. !INSON FILL ("/)

RADIO PROGRAMINGPGM KEY (8) NORMAL NET

". SELECT NET TO MODIFY. ACTI!ATE IN LISTYES'. NET TYPESATCOM

FREQ

. FREQ CODE(HM # ON SAA)". RX& TX& FREQ (SHOULD SET AUTOMATICALY)

. RECEI!E ONLYNOCOMSEC. CRYPTO MODEKG8'". ENCRYPTION KEYTEK 0. SYNCHRONI$ATIONREDUNDANT (MODE )'. HPW TRANSEC KEY ID0

DATA/VOICE. DATA*!OICEDATA". MODULATIONHPW. ENABLE TCPIPNO

SQUELCH

. SQUELCHOFFPOWER

". TX POWER LE!EL"0 WATTS (AS REQUIRED). !AU POWER /0 WATTS (AS REQUIRED)

NAME

. NAME(WHATE!ER THE NAME OF THE NET IS)

HIT CLR TIMESRADIO PORTS

PGM KEY (8)PORTS

REMOTE. INTERFACE(AIC PORT)". PROTOCOLRS "". ASYNC RATE00'. DATA BITS8/. PARITYNONE. STOP BITS. FLOW CONTROLNONE

11


12/21

8. ASYNC ECHOON. HIT CLR " TIMES

TIME (NOTE: 6ULIAN DATE WILL BE DAY MONTH YEAR). OPTION KEY ()

TIMEHPW

READING LEFT TO RIGHT YOUR TIME WILL BE AS FOLLOWSDAY MONTH YEAR& YOUR TIME (NOTE: 6ULIAN DAY WONT BE THERE)CONNECT THE DATA CABLE AT THIS TIME (IF THE DATA CABLE WONT PLUG IN THE COMPUTER THEN YOU MUST USE A USB ADAPTER TO OBTAIN A CONNECTION%CONNECT THE ANTENNA AT THIS TIMECOMPUTER

CLICK ON THE GLOBE THAT READS RF-))0FILEIMPORT DATABASE (RPA THAT GOES TO THE NET AT THAT TIME)

GENERATE ROUTES! NEXT TO TRAFFIC LIGHT CLICK ON THE IMAGE WITH TWO ARROWS POINTING DOWN! ONCE YOU OPEN UP GENERATE ROUTES MAKE SURE ITS FOR ALL STATIONS AND CLICK OK! ROUTES WERE SUCCESSFULLY GENERATED CLICK OK! NOW RIGHT CLICK ON THE STATION YOU,LL BE USING (EX.RCTANTHILL)! ONCE YOU RIGHT CLICK SELECT PROPERTIES! CHECK LOCAL STATION AND HIT OK! CLICK ON GENERATE ROUTES AGAIN BUT THIS TIME CLICK ON FOR THE STATION YOU,LL BE USING

(EX.RCTANTHILL) AND CLICK OK! ROUTES WERE SUCCESSFULLY GENERATED CLICK OK! CLICK ON TRAFFIC LIGHTS

NOTE:(THE TRAFFIC LIGHTS SHOULD GO FROM REDYELLOWGREEN)

OUTLOOK EXPRESS WILL OPEN UP AND CONNECT TO THE SER!ER

CLICK ON START

! CONNECT TO! SHOW ALL CONNECTIONS! RIGHT CLICK ON HARRIS AUTOMATIC IP RADIO CONNECTION (COM )! AND CONNECT TO THE SER!ER

SENDING MESSAGES! CLICK ON CREATE MAIL! CLICK ON (TO:)

ENTER THE NAME OF THE STATION YOU SENDING A MESSAGE TO EX.RCTCOC! CLICK ON SUB6ECT

ENTER THE SUB6ECT EX.(RADIO)! WRITE THE MESSAGE! CLICK SEND

PROTOCOL STATUS4 WILL GO FROM IDLECONNECTSEND

HPW-HIGH PERFORMCE WAVNGTHCREATING RPA$

GETTING STARTED$

OPEN 11F RPA

PLAN INFO TAB4 AUTHOR (YOUR NAME)4 ORGANI$ATION (UNIT NAME)4 PLAN !ALIDITY (START DATEEND DATE)4 DESCRIPTION

STATIONS TAB4 STATIONS NAME (STATIONS YOU,LL BE USING) EX. RCTCOC4 ENTER ALL STATIONS AND DEFINE

NETS TAB4 NET NAME (THE NET YOU,LL BE USING) EX. RCTCMD4 PRESET TYPE (DEDICATED SATCOM)4 NET #04 PRESS ADD4 MAKE SURE (ACTI!ATE AND ALL STATIONS ARE CHECKED)4 CLICK ON DETAILS4 GENERAL

FREQ CODE (ENTER DOWNLINK AND UPLINK)4 COMSEC

CRYPTO MODE(KG8'&TEK 0&REDUNDANT MODE )4 DATA*!OICE (MAKE SURE ITS ON DATA PORT)

SATCOM MODE(HPW)

INFO TYPE(DATA) BAUD RATE (NB)

12


13/21

MODULATION(HPW)

SQUELCH (DEFAULT)

AD!ANCE (DEFAULT) FINISH

4 ADD NOTE77 (MAKE SURE ACTI!ATE AND ADD ALL STATIONS ARE CHECKED AND THE STATIONS ARE

ADDED. GLOBAL RADIO CONFIGURATIONS TAB

4 DEFAULT GLOBAL WA!EFORM CONFIGURATIONS

4 DEDICATED SATCOM

NOTE77 (WHEN USING CUSTOM FREQUENCY CODES 8& IT,LL BE IN RX ONLY& IN ORDER TOHA!E AN UPLINK AND DOWNLINK& YOU MUST USE FREQ CODE (ID) ABO!E

4 UNDER (USE DEFAULT TABLE)4 ENTER DOWNLINK FREQ (RECEI!E FREQ)

• NOTE77 (MAKE SURE ID # IS 8 AND BANDWITH "/K)4 CLICK ON (USE CUSTOM FREQ CODE)

• MAKE SURE ID IS ABO!E ()& THEN UPLINK SHOULD BE A!AILABLE4 ENTER UPLINK FREQ AND PRESS ADD

• NOTE77 (NOW YOU CAN DELETE THE RX ONLY ID)

SAVE AND THAT'S YOUR RPA

TO IMPORT YOUR RPA! CLICK ON THE MAGIC WAND (" DOWN FROM TRAFFIC LIGHT)

NETWORK SETUP WI$ARD SHOULD COME UP! GO TO BROWSE (AND OPEN THE SA!ED RPA)! CLICK NEXT! CLICK ON (ADD STATIONS TO AN EXISTING EMAIL) IF NOT EXISTING CREATE A NEW ONE! NEXT AND SHOULD SAY +YOU,!E DONE3

! ALL STATIONS SHOULD COME UP! GO TO STATIONS AND RIGHT CLICK ON STATIONS! CHECK TO SEE IF RADIO ATTACH TO IT! IF NOT ADD RADIO AND HPW ADDRESS

MODIFY NET! AFTER THAT UNDER RADIO NETWORKS RIGHT CLICK ON THE NET (EX. RCTCMD) AND CLICK PROPERTIES! NET PROPERTIES

NUMBER OF RETRIES ON FAILURE ()

DELAY BETWEEN RETRIES ()! NET MEMBERSHIP

MAKE SURE ALL RADIO NETS INCLUDED WITH HPW ADDRESS AN/PRC-15" DEDICATED SATCOM

PREPARING THE SKL

• GO TO KEYS

• CHOOSE THE "08(AND!T) KEY (CHOOSE THE SEGMENT OF CRYPTO WE ARE USING)

• HIGHLIGHT THE KEY

• AFTER HIGHLIGHTING THE KEY CHOOSE THE LOAD BUTTON IN THE TOP RIGHT CORNER

• ON THE NEXTSCREEN ALL OF IT SHOULD ALREADY BE DEFAULT% PRESS OK

• NEXT SCREEN WILL BE DEFAULT% PRESS OK

• THEN YOU SHOULD BE ON THE FINAL SCREEN WHICH TELLS YOU TO HIT INITIATE BUTTON (INITIATE BUTTONWILL BE ON THE /" WHEN IT IS READY TO LOAD)PREPARING THE 15" FOR CRYPTO LOAD

• ON TOP OF THE /" YOU PUT THE FUNCTION KNOB ON LOAD

• ON THE SCREEN THAT COMES ON YOUWILL CHOOSE FILL

• WA!EFORM FOR KEY: CHOOSE !ULOS

• FILL DE!ICE: CHOOSE KYK

• NOW THE /" IS READY TO BE LOADED WITH CRYPTO

• NOW PRESS THE INITIATE BUTTON(ENTER IS THE INITIATE BUTTON)

• ON THE SKL (WHEN IT IS DONE LOADING) A SCREEN SHOULD POP UP SAYING OPERATION SUCCESSFUL

•

ON THE /" YOU WILL SEE CRYPTO MODE: CHOOSE AND!T• NEXT SCREEN YOU WILL SEE KEY TYPE: CHOOSE TEK% KEY NUMBER: CHOOSE 0

• NEXT SCREEN YOU WILL SEE CLASSIFICATION: CHOOSE SECRET

• NEXT SCREEN YOU WILL SEE LOAD ANOTHER KEY: CHOOSE NO

• NOW YOU ARE DONE LOADING CRYPTO

SWITCH THE FUNCTION KNOB BACK TO CT

PROGRAMMING THE 15"

FIRST HIT THE 8*PGM KEY

NEXT SCREEN GO DOWN AND CHOOSE SYSTEM PRESETS

NEXT SCREEN CHOOSE SYSTEM PRESET CONFIG

13


14/21

NEXT SCREEN WILL SAY SYSTEM PRESET NUMBER (CHOOSE THE PRESET CORRESPONDING TO THE NUMBER ONTHE FUNCTION KNOB THAT YOU WILL BE USING THIS NET ON)

• NEXT SCREEN YOU WILL SEE PRESET DESCRIPTION ( LEA!E IT DEFAULT)

• NEXT SCREEN YOU WILL SEE PRESET WA!EFORM: CHOOSE !ULOS

• NEXT SCREEN CHOOSE GENERAL CONFIG

• NEXT SCREEN SAYS PRESET NAME (HERE YOU WILL PUT IN THE NAME OF THE NET% DOING SO ON THE /"IS SIMILAR TO TRADITIONAL TEXTING ON A CELL PHONE)

• NEXT SCREEN WILL BE PRESET TYPE: CHOOSE SATCOM

• NEXT SCREEN GO DOWN AND CHOOSE FREQUENC

• NEXT SCREEN WILL SAY CHANNEL NUMBER (HERE YOU WILL KEY IN THE DIGIT FREQ CODE FOR THE NET)

• NEXT SCREEN WILL BE RX FREQUENCY: DEFAULT (FREQUENCY SHOULD BE SET AUTOMATICALLY FROM

ENTERING THE FREQ CODE)• NEXT SCREEN IS RECEI!E ONLY: CHOOSE NO

• NEXT SCREEN SAYS TX FREQUENCY: CHOOSE USE RX FREQ

• NEXT SCREEN SHOULD SAY TX FREQUENCY: DEFAULT (NOTE: CHECK YOUR SAA FOR THE RX AND TXFREQUENCY& IF IT SAYS OTHER THAN WHAT THE FREQ CODE DEFAULTS YOU MAY HA!E TO ENTER EACHMANUALLY)

• NEXT SCREEN GO DOWN AND CHOOSE COMSEC

• NEXT SCREEN WILL SAY CRYPTO MODE: CHOOSE AND!T

• NEXT SCREEN SHOULD SAY CRYPTO KEY: CHOOSE TEK 0

• NEXT SCREEN WILL SAY TRAINING FRAMES: CHOOSE "0

• NEXT SCREEN WILL SAY AND!T RX PRIORITY: CHOOSE ENABLED

• NEXT SCREEN WILL SAY !OICE AUTOSWITCH: CHOOSE ENABLED

• NEXT SCREEN GO DOWN AND CHOOSE TRAFFIC

• NEST SCREEN WILL SAY TRAFFIC MODE: CHOOSE !OICE AND DATA

• NEXT SCREEN WILL DATA MODE SYNCHRONOUS: PRESS ENTER

• NEXT SCREEN WILL SAY !OICE MODE: CHOOSE EITHER LPC "'00 OR MELP "'00

• NEXT SCREEN WILL SAY LPC CODEBOOK: CHOOSE ENGLISH

• NEXT SCRREN WILL SAY OPTION CODE: CHOOSE 00

• NEXT SCREEN GO DOWN TO TX POWER

• NEXT SCREEN WILL SAY TX POWER LE!EL: CHOOSE HIGH

• NEXT SCREEN GO DOWN TO SQUELCH

• NEXT SRCREEN WILL SAY SQUELCH DISABLED: PRESS ENTER

• NEXT SCREEN WILL SAY FM TRANSMIT TONE: PRESS ENTER

• NEXT SCREEN GO DOWN TO EXIT

• CLR TO MAIN SCREEN NOW YOU ARE READY TO TALK ON THE DEDICATED SATCOM NET WITH YOUR 15" NOTES ON PRC-15" *DAMA

RADIO$

. CONNECT RT TO !AU

". TURN !AU AND RT ON#% SWITCH FUNCTION KNOB TO FP

LOAD CRYPTO. SWITH THE FUNCTION KNOB TO LD". WA!EFORM KEYDAMA. FILL DE!ICEKYK ENT'. LD AND!T ENT/. CYRPTO MODE SELECT AND!T ("08X). SELECT TEK0. CLASSIFICATION SECRET8. LOAD ANOTHER KEY YES. REPEAT STEPS "0. CYRPTO MODE SELECT ORDERWIRE (C//X). SELECT TSK 0". CLASSIFICATION SECRET. LOAD ANOTHER KEY NO'. SWITCH FUNCTION KNOB TO CT

DAMA RADIO PROGRAMINGPGM KEY (8)SYSYEM PRESETS .ENTSYSTEM PRESET CONFIG. ENTACTI!E PRESET CHANNEL% ENTENTER PRESET DESCRIPTION. ENTPRESET WA!EFORM DAMA. ENTWA!EFORM MODE DAMA. ENT

14


15/21

PICK /K8"A OR PICK "/K 8A. ENTCHANNEL

+% ENTER CHANNEL # (HM CH ON SAA) ENT5% TX CABIBILITY FULL (TX ENABLED) ENT)% CONSANT KEY PORT NO% ENT% SET CUSTOM CHANNELS NO. ENT

RANGING

. RANGING METHOD ACTI!E. ENT"% PLATFORM CON FIG FAST MO!ING ENT

ADRESS1% BASE ADRESS (TBA OR TERMINAL BASE ADDRESS) ENT". GUARD LIST ON SMART CARD OR SAA (, 1 TO THE END OF GUARD LIST IF IT IS A ODD . (EX% )"+5 SHOULD BE

)"+5. ENT. PRESS CLR " TIMESTRANSEC

. ODERWIRE ENCRIPTION ON ENT". KEY LOCATION TSK ENT. DEFAULT ODERWIRE KEY ENT

TRAFFIC. TRAFFIC MODE !OICE ENT". !OICE MODE MELP. DASA OPT CODE 00

POWER

. TX POWER DB FROM FULL ENTPRESET NAME

. NAME(WHATE!ER THE NAME OF THE NET IS) ENTI/O PORT CONFIG

. DAMA CONFIG CODE 00 ENT". AND!T ENHANCED ENT

. CRYPTO TEK TEK 0 ENT'. TRANNING FRAMES "0 ENT/. AND!T FADE PRIORITY PTT ALLOWED ENT

RADIO 5KHZ MESSAGE MODE

1% AUTOMATICEXIT

. TAKES YOU TO PRESET CONFIG PRESS CLEAR TO PROGRAM MENU ENTPROGRAM MENU

. DAMA CONFIG ENTDAMA CONFIG

. GENERAL CONFIG ENT". DESTINATIONS ENT. DEFINE DESTINATION ENT'. SELECT DESTINATON 0 OR DESTINATION# TO BE MODIFIDED (SAME AS PRESET YOU MODIFIED EARLIER) ENT/. DESTINATION NAME ( NAME YOU CHOSE) ENT. DESTINATION TYPE 5 8A AC "/K AC& 8"A /K. ADD ADRESS GUARD LIST ENT

8. EXIT AND CLEAR ALL THE WAY OUTOPERATION OF DAMA

. LET RADIO AQURIE DOWNLINK". ONCE RADIO IS CONNECTED. PRESS KEY'. SCROLL TO PLACE CALL ENT/. PICK DESTIONATION GUARD LIST # (USE THE ONE YOU PROGRAMMED) ENT. PRESS ENTER TILL CALL IS PLACED.. WAIT FOR IT TO SAY CONN ABO!E NET8. PLACE A CALL. MAKE A RADIO CHECK

NOTE$ YOU CAN CHECK STATUS UNDER KEY OPTIONS UNDER DAMA OPTIONSTROUBLESHOOTING STEPS

IF YOU CANNOT PLACE A CALLPRESS THE CALL () KEYSEND STATUS REPORT BPRESS THE CALL () KEY

LINK TEST (WILL TAKE ABOUT / MIN)PRESS THE CALL () KEYPLACE A CALLSELECT DESTINATION (THE ONE YOU PROGRAMMED)ONCE THIS IS DONE YOUR NET SHOULD BE ACTI!E AND CONNECTED7

CY$0

R2324 D676869(L!6:97 64: K;9. PYQ-10(SKL.

O= CY$0

15


16/21

T= CY$0 4=.

. P>@@ +LOCK LTR3 @4 > 4 +LETTER3 @ 4; > @?>>=.". H M4>3 @>>? +CT3& >@@ N>/. S>>? =>>> 4 > @>= (@>>?> 4;@& >=& = >@). P>@@ +T=@; @ @?>>=

O= CY$0. W? CT 4 >;4> CT3 @?>>= @@@ ENTR"% O=?> ?4;>>& >@@ ABORT 4 >= 4 > CT ;>=

U469924 ?;9 L!6:97

. T= CY$0 4=.". P>@@ +LOCK LTR3 @4 > 4 +LETTER3 @ 4; > @?>>=.. H@@ 4 4 > 4 4 4 >.. P>@@ 4 +D4=>3& >@@ ENTR. S?>>= & +C> = 4=>& 14?3 @?>>= =.

A9924 ?;9 7! L!6:97. T= CY$0 4=.". P>@@ +LOCK LTR3 @4 > 4 +LETTER3 @ 4; > @?>>=.. H>= = 4 > +S>1L4?3 @?>>= (@ 0)/. P>@@ +P DN3 @4 @?>>= +L4?:C"31)% R>> @>@ 0/ 4 C"C

D@724 K;9

. T= CY$0 4=.". P>@@ +LOCK LTR3 @4 > 4 +LETTER3 @ 4; > @?>>=.. H


17/21

. +S>>? 4>>=& @>>? +>>>3'. U@> P DN*P UP 4 =;> 4 > >(@) 4 = 4 >>> (4; @> )/. P>@@ ENTR 4 = @> 4 > >(@) 4 = 4 >>>. R3& >@@ ENTR. +C4=>>-3 @@ ABORT @ 4 > CT ;>=

D@724 L!6:979 (P@679 64: E2>47.

. T= CY$0 4=.". P>@@ +LOCK LTR3 @4 > 4 +LETTER3 @ 4; > @?>>=.. H P DN*P UP 4 @>>? >= 4 > >>>/. R 4 +>3& >@@ ENTR. U@> P DN*P UP 4 @>>? >= 4 >>>. P>@@ ENTR 4 = @> 4 >= 4 > >>>8. R3& >@@ ENTR. +C4=>>-3 H


18/21

. H3 K . +C4 >3 !& KG8'& AND!T& >?.'. +TEK3*3TSK3 +03/. +P>@@ ENT 4 I= RT @

O= CY$0

. T= > 4=.". P>@@ +LOCK LTR3 @4 > 4 +LETTER3 @ 4; > @?>>=.. H3& @>>? +KYK3. S?>>= & +P>@@ >=> 4


19/21

O= CY$0

. T= > 4=.". P>@@ +LOCK LTR3 @4 > 4 +LETTER3 @ 4; > @?>>=.. H ?4;>>& >@@ ABORT 4=?> 4= CY$0 4 >= 4 > CT ;>=.

L!6:24 PRC-15" (@!6:97.

O= RT

. T= RT 4=.". S>? +F


20/21

. +CIK I=3 8. T> = @?>>=. I 4 4 ENTR >>> = >>= > 4 4

@4. F44 > ?= 4 CIK 4= > CY$0

;=& J4 4 +S>3& >@@ ENTR@@ ENTR 4 4=& +Y>@3 >& @@ CLR. >= @4@ >> ?>> @??>@@& >@@ CLR => @>@ "" @> 4 AN*CY$0,@ > CIK ;4> 4 S> :

. M=S>M4>D> CIKC=J> D> CIKS>


21/21

radio study material

Documents