ISO 9000:2000

American National Standards

American Society of Testing and Materials

Steel Doors Institute

National Structural Code of the Philippines

Building Code of the Phils.

American Institute of Steel Construction, Inc.

Steel Door Jambs

Classic 1 Classic 2 Modern 3

  JAMB / FRAME PANEL

Material Black Iron Black Iron

Skin Thickness 1.1mm / Gauge 20 0.76mm / Gauge 22

Panel Thickness   40mm with lip

Profile A-100  

Paint One coat epoxy gray primer

One coat epoxy gray primer

Insulation   Paper Honeycomb

Rapid Steel Doors Wooden Doors

COMMERCIAL DOORSD1 Series

SPECIAL FEATURES :

1. Rust inhibitive primer in accordance with ANSI A250.10

2. Patented A-100 profile 3. Stiffeners for easy installation4. Cut-out for locking system, standard cylindrical knob-

type locksets5. Spreader to avoid twisting during handling6. Welded hinges , 2-pcs Stainless Steel Flag Hinges7. Fire-rated 45minutes, Manufacturer’s Rating

AVAILABLE SIZES :

700 x 2100 mm800 x 2100 mm900 x 2100 mm

D3 SERIES DOORS

RFC D3 Series Steel Doors are designed for heavy and extra heavy duty application in both commercial and institutional buildings. They can be installed both in interior and exterior application and to any wall type construction.

SPECIFICATION :SPECIFICATION :

Steel ThicknessSteel Thickness : Jamb :MSG No 16 (1.3 mm) Panel :MSG No 20 ( 0.8mm)

Panel Thickness: 40mm or 44mmPanel Thickness: 40mm or 44mm

Material Compliance :Material Compliance : 1. Cold-Rolled Steel (CRS-BI) conforming to ASTM A

1008/A 1008M2. Hot-Rolled Steel (HRS-BI) conforming to ASTM A

1011 /A 1011M3. Galvanized Iron (GI) conforming to ASTM A 653/A

653M

AVAILABLE SIZES :Single Leaf : up to 1220 x 2440mmDouble Leaf : up to 2440 x 2440mm

Header :Horizontal member connecting the jambs

Hinge Jamb :vertical member of steel jamb prepared for installation of hinges

Strike Jamb :vertical member of steel jamb prepared for latches

BASIC STEEL JAMB

Steel Thickness: MSG No 20Steel Type : Cold-Rolled SteelRust inhibitive primerPatented A-100 profile

Stiffeners for easy installationCut-out for locking system, standard

cylindrical knob-type locksetsSpreader to avoid twisting during handlingWelded hinges , 3-pcs 3.5” x 3.5 x 1.5 Butt

Loose Pin Brass Plated Hinges

EASY-TO-INSTALL1.0 Setting

1.1 Look for the lay-out and center lines references1.2 Set the frame based on these provisions.1.3 Hinge Jamb and Strike Jamb should have a minimum gap from the wall side of 20mm while that of the header side not less than 100mm should be provided for hand movement during grouting.

2.0 Plumbing and bracing2.1 The installer should be equipped with a carpenter level, square and plumb bob with string.2.2 Level the Header2.3 Square jambs to header. Shim under frame if necessary2.4 Plumb and square the frame

3.0 Dowelling and Welding3.1 Weld frame stiffeners to initial dowel provided on site3.2 Install vertical deformed bars by welding to dowels3.3 Weld frame stiffeners to the vertical bars3.4 Check alignment

EASY-TO-INSTALL

4.0 Formworks4.1 Install formworks.4.2 Make sure to take into consideration allowances for grooves and skim coating or plastering

5.0 Grouting5.1 Mix grout as specified 5.2 Ensure that the mixture consistency is enough to penetrate the throat of the jamb, ensure a not “pumpable” consistency, a maximum slump consistency of 4” is recommended.5.3 Pour grout on the jamb throat by layer 5.4 Tap the form as pouring progresses to remove air bubbles to prevent honeycomb of grout5.5 Hand trowel grout on the header side

6.0 Curing and Stripping6.1 Remove formworks after 8 hours or after grout has completely set.6.2 Remove excess grouts6.3 Clean

ROOF FRAMING SYSTEM

Based on a combination of rafters & purlins;No trusses or bottom chords

ROOF FRAMING SYSTEM

Ayala Land Inc. / Makati Development

Corp.

DESIGN DRAWING

R-C

R-C

R-C R-C

MAIN ROOF FRAMING PLAN

R-B

R-C

R-C

R-C

R-A

R-AR-C

LOWER ROOF FRAMING PLAN

RB-1

R-A

R-C

RB

-1R-A

R-C

R-C

NOTES:

RAFTER ELEVATION

ERECTION DRAWING : 3-D Modeling on X-STEEL

FABRICATION

RAPID FORMING CORPORATION’SROOF FRAMING SYSTEM

Easy-to-install

RAPID FORMING CORPORATION’SSTEEL HOUSE SYSTEM

Kingdom Hall of Jehovah’s WitnessesSteel House

Camella Homes Montserrat - Mactan

CONTACT US :

Manila:2F Vasquez Madrigal Plaza51 Annapolis St., GreenhillsSan Juan, Manila 1500Tel. Nos.(02)7263533Fax No.(02)7263503

Cebu :P. Remedio St., Banilad, Mandaue CityTel. Nos. (032)5057845Fax No.(032)344-9077

Email :rfccebu@rapidforming.comsales@rapidforming.com

Website & Blog :http://www.rapidforming.comhttp://www.rapidforming.info