raw mill supplement manual

8/17/2019 Raw Mill Supplement Manual

1/21

REVISION: NCM119-SM

IMPORTANT NOTES ON THE DOCUMENTATION

SUPPLEMENT

NCM119-SM

EXAM. & APPROVER

EXAM. & CHECKER

CORRECTOR

COMPILER

TOTAL VOLUMES 1 VOLUMES RESUMED

PAGES OF THE VOLUME 19

SINOMA INTERNATIONAL ENGINEERING CO., LTD.

DATE: 2006.02


2/21

REVISION: NCM119-SM

CONTENTS

1 LEGAL INFORMATION..............................................................................................1

1.1 LIABILITY AND WARRANTY ...............................................................................................1

1.2 COPYRIGHT .....................................................................................................................1

1.3 TECHNICAL MODIFICATIONS ............................................................................................1

2 GENERAL SATETY REQUIREMENTS..............................................................2

2.1 PRINCIPLES......................................................................................................................2

2.2 MODIFICATIONS AND SPARE PARTS.................................................................................2

2.3 PERSONNEL.....................................................................................................................3

2.4 DISMANTLING AND DISPOSAL

..........................................................................................32.5 DESIGN AND MEANING OF WARNINGS .............................................................................3

3 GENERAL INSTRUCTIONS FOR LUBRICATION .......................................7

3.1 GEAR UNIT .......................................................................................................................7

3.2 OIL HEATING.....................................................................................................................8

3.3 ANTIFRICTION BEARING...................................................................................................8

3.4 OPEN GEAR WHEELS .......................................................................................................8

3.5 L ABYRINTH SEALS ...........................................................................................................8

3.6 LUBRICATION PIPE ...........................................................................................................93.7 NOTE!...............................................................................................................................9

4 SINOMA TABLE OF LUBRICANTS...................................................................10


3/21

REVISION: NCM119-SM

Page 1 of 19

1 LEGAL INFORMATION

Dear Customer,

This manual is issued by SINOMA to be observed in every detail by thoseresponsible for the transport, assembly, commissioning, operation, maintenance

as well as the dismantling and disposal of the machinery and plant. Only if the

responsible individuals follow the instructions in this manual, will errors in

operation and maintenance of the machinery and plant be avoided and

troublefree operation be ensured.

1.1 Liabil ity and warranty

SINOMA explicitly exclude all liability and warranty claims for damage or

operational malfunctions originating from:

Disregarding of information/instructions in the manual.

Incorrect operation.

Any use of the machine other than the specified use.

Faulty maintenance.

Use of consumables (in particular by lubricants) not explicitly permitted by

the manufacturer.

Use of spare parts not approved by the manufacturer.

Conversions and modifications not approved by the manufacturer.

In addition, the conditions for liability and warranty as specified in the General

Conditions of Supply of SINOMA are applicable.

1.2 Copyright

SINOMA reserve all rights in connection with this documentation. Including those

relating to patent registration or provisional patent registration. Without our

previous consent, this documentation may neither be made available to third

parties nor be reproduced without permission or be used in any other

unauthorized manner.

1.3 Technical modi fications

SINOMA reserve the right to change designs in the course of technical


4/21

REVISION: NCM119-SM

Page 2 of 19

developments. Recent modifications may not yet have been included in the

diagrams and texts of this manual.

2 GENERAL SATETY REQUIREMENTS

2.1 Principles

The machine has been manufactured in accordance with the state of the art

and the recognized safety regulations. This, however, does not preclude

danger to life and limb for the user or others, nor does it prevent harm to the

machine and/or other property.

These safety instructions must be observed by all persons responsible for

the transport, assembly, commissioning, operation, maintenance as well as

the dismantling and disposal of the machine. We recommend that the owner

obtains a signed confirmation that the safety instructions have been read and

understood by the personnel.

The machine should only be used when it is technically serviceable. It must

be operated in compliance with the machine’s instruction manual bearing in

mind safety and possible dangers. Serviceable condition implies that the

whole working area is clean and tidy. This has to be ensured by instructionand inspection.

Make sure that all additional national laws regulations for accident

prevention and protection of the environment are complied with.

Make sure that the warnings and safety instructions at and on the machine

are complete and well legible.

Make sure that the complete technical documentation for the user of the

plant is always available at the workplace.

Never step onto or climb upon safety devices such as railings, mesh guards

or covers. Only use suitable ladders or scaffolds to reach inaccessible parts

of the machinery or plant.

2.2 Modifications and spare parts

For safety reasons, conversions and modifications are prohibited unless

previous approved by SINOMA.

Use of accessories and spare parts not approved by SINOMA can lead to

unforeseeable dangers.


5/21

REVISION: NCM119-SM

Page 3 of 19

2.3 Personnel

Only trained and authorized personnel may be employed for operating the

machine.

The operating and maintenance personnel must always wear the necessary

protective clothing such as safety boots, tough top clothes, safety gloves and

safety helmets. As the owner of the plant, you are responsible for ensuring

that this demand is complied with by your personnel. Please ensure that all

applicable national regulations are observed.

The operations of the plant are not exposed to noise emissions of machinery

as the machines designed and supplied by SINOMA are operated form a

central control room.

The maintenance personnel is obliged to check the machinery at least once

every shift for visually detectable damage or faults. If any damage, fault or

change in the operational behaviour is detected, the dits must immediately

inform the responsible superior. If necessary, shut down the machine

immediately!

During maintenance work, cordon off the entire working area to prevent

unauthorized persons form gaining access.

Maintenance work may only be performed by trained specialists. Work on work fittings and gas consuming installations may only be

performed by specially qualified personnel.

Work on the electrical equipment of the machine may only be performed by a

qualified electrician or by authorized person under the supervision of a

qualified electrician in accordance with the electro-technical regulations.

Hydraulic equipment may only be dealt with by personnel with specific

knowledge and experience in hydraulic.

2.4 Dismantling and disposal

Ensure the safe and the environment-friendly disposal of all consumables

and process materials. You should also make sure that all respective

national regulations for the protection of the environment are complied with.

2.5 Design and meaning of warnings

The machine and operating manuals of SINOMA refer to various types of


6/21

REVISION: NCM119-SM

Page 4 of 19

warnings each consisting of a warning design, signal word and text. The

design of the warning notices varies depending on the type, nature and severity

of the danger.

2.5.1 Explanation of the warning signs

The warning signs give either a general warning of a danger of warn of a certain

hazard. They have the following meanings:

General warning of a danger

Warning of dangerous electrical voltage

Warning of radioactive substances or ionizing radiation

Warning of explosive substances

Warning of inflammable substances

Warning of explosive atmosphere

Warning of toxic substances

Warning of hot surface


7/21

REVISION: NCM119-SM

Page 5 of 19

Warning of danger of stumbling

Warning of danger of slippling

Warning of danger of falling

Warning of danger of being caught, crushed or pul l in

Warning of mangling of cutting off

Warning of danger due to material spattered or thrown out

Warning of danger of impact

Warning of danger of inhaling toxic substances

Warning of danger of material falling out

Warning of danger of caustic substances


8/21

REVISION: NCM119-SM

Page 6 of 19

2.5.2 Signal words

The warning sign is accompanied by signal words pointing out the severity and

probability of the danger:

DANGER- Direct danger imminent. If you expose yourself to this danger,

you will risk your life or may suffer severe injury or be maimed.

WARNING- There is a potential danger. If you expose yourself to this

danger, death or severe injury may be the consequence.

CAUTION- There is a danger. If you expose yourself to this danger, you

may suffer injury.

Or : If you ignore this warning, damage to property may be the consequence.


9/21

REVISION: NCM119-SM

Page 7 of 19

3 GENERAL INSTRUCTIONS FOR LUBRICATION

For an optimal lubrication and a long durability of the lubricants, consider the

following instructions:

Close the containers immediately after lubricant has been extracted, Store

the containers in closed and dry rooms, Contamination of the lubricants is

thereby prevented. Ensure that the lubricants are stored, used and disposed

of in a way compatible with the environment, and observe the relevant

national environmental legislation when handling lubricants.

Observe your national legislation for industrial safety, health and fire

protection when storing and handing lubricants.

Mark the barrels and canisters according to types with different colour.

Mixing of lubricants is not permitted.

Re-lubricate at regular intervals with adequate lubricant quantities. Lack or

insufficient of lubricants can cause damage to the machine components.

For flushing, use a low-viscosity oil on the same base and from the same

manufacturer. Never mix oil on a mineral base with synthetic oil.

3.1 Gear uni t

NOTE!

For selection of the oil the viscosity indicated on the identification plate of the

gear unit is decisive.

For the quantity to be filled only the oil level measurement at the inspection

glass, at the measuring rod or at the oil overflow opening is decisive.

Change oil at the intervals prescribed by the manufacturer of the gear unit. In

addition, check the oil level continuously and possibly supplement lacking

quantities.

Scavenge the drive unit thoroughly at every oil change. The flushing oil must

be of flow viscosity. Never use petroleum for flushing gears.


10/21

REVISION: NCM119-SM

Page 8 of 19

When oil of the same oil type is change the residual quantities in the gear

unit must be as small as possible. Small residual quantities do as a rule not

cause difficulties. Gear oil of different types and from different manufacturers

must not be mixed. We recommend that the plant owner obtains, if necessary,

a signed confirmation that the new oil is compatible with the residuals of the

waste oil.

In case the oil type is changed from polyethylene glycol to a different gear oil

or vice versa the gear unit must always be thoroughly scavenged with the

new oil. Residual waste oil must be completely removed from the gear unit.

3.2 Oil heating

Unfavorable climate conditions may necessitate a heating up of the lubricating oil.

Take care that the heat transferred per unit surface in the oil at rest does not

exceed 0.5 to 1W/cm2. When the doubt consult the plant or lubricant supplier.

3.3 Antifr iction bearing

A lubricating grease quantity which is too great causes increased operating

temperatures especially with higher speeds.

Fill the housing of slowly running bearings which must adequately be

protected from corrosion completely with grease.

3.4 Open gear wheels

DANGER !

Open girth gear drive units or gear racks can pull in andsqueeze parts of the body.

You may suffer severe injury. Never lubricate when the machinery is operating.

Thoroughly clean open girth gear drive units or gear racks prior to the lubrication.

Apply a uniform and thin lubricating film.

3.5 Labyrinth seals

The seals are to prevent dirt from entering the bearings. Therefore always

re-lubricate until a grease collar forms before the labyrinth passages. When the


11/21

REVISION: NCM119-SM

Page 9 of 19

grease collar has been used up re-lubricate with fresh grease until a new grease

collar has formed.

3.6 Lubr ication pipe

Take care that the lubrication pipes to the friction points are thoroughly cleaned

inside and filled with the prescribed lubricant prior to commissioning.

3.7 Note!

The selection of the lubricants for the ref. numbers is on the responsibility of the

lubricant supplier. SINOMA is not responsible for the correctness of this data.

In the case of extremely difficult lubricating conditions and special designs, thespecial regulations of SINOMA apply. No responsibility is assumed for the use of

any other lubricants than those listed in this section unless they have been

explicitly approved by SINOMA.

Each mineral-oil company mentioned in the table of lubricants keeps a

lubrication service with engineers who, on request, are at our customers’

disposal and advise them with regard to all questions relating to suitable

lubrication.


12/21

REVISION: NCM119-SM

Page 10 of 19

4 SINOMA TABLE OF LUBRICANTS


13/21

REVISION: NCM119-SM

Page 11 of 19

Hydraulic oi ls HLP acc. to DIN 51524 / part 2 on mineral oil basis

Ref. no. 2 3 4 5 6

Viscosity VG 22 VG 32 VG 46 VG 68 VG 100

Ident. no. 1166919 1166920 1166921 1166922 1166923 Agip OSO22 OSO32 OSO46 OSO68 OSO100

ARAL Vitam GF 22 Vitam GF 32 Vitam GF 46 Vitam GF 68 Vitam GF 100

BECHEM Staroil NR.22 Staroil NR.32 Staroil NR.46 Staroil NR.68 Staroil NR.100

BPEnergol

HLP-HM 22

Energol

HLP-HM 32

Energol

HLP-HM 46

Energol

HLP-HM 68

Energol

HLP-HM 100

BrugarolasFluid Drive

HM-22

Fluid Drive

HM-32

Fluid Drive

HM-46

Fluid Drive

HM-68

Fluid Drive

HM-100

Castrol Hyspin SP 22 Hyspin SP 32 Hyspin SP 46 Hyspin SP 68 Hyspin SP 100

ESSO Nuto H 22 Nuto H 32 Nuto H 46 Nuto H 68 Nuto H 100

Fuchs Europe

Lubricants

Renolin B5

VG 22

Renolin B5

VG 32

Renolin B5

VG 46

Renolin B5

VG 68

Renolin B5

VG 100

FUCHS

LUBRITECHRenolin B5 Renolin B10 Renolin B15

Gearmaster

CLP 68

Gearmaster

CLP 100

KLÜBER ------Lamora

HLP 32

Lamora

HLP 46

Lamora

HLP 68

Kluber-Summit

HySyn FG-00

Mobil Mobil DTE 22 Mobil DTE 24 Mobil DTE 25 Mobil DTE 26 Mobil DTE 27

Shell Tellus 22 Tellus 32 Tellus 46 Tellus 68 Tellus 100

TEXACO /

CALTEXRando HD 22 Rando HD 32 Rando HD 46 Rando HD 68 Rando HD 100

TotalFinaElf AZOLLA ZS

22

AZOLLA ZS

32

AZOLLA ZS

46

AZOLLA ZS

68

AZOLLA ZS

100

TribolTribol 943AW

22

Tribol 943AW

32

Tribol 943AW

46

Tribol 943AW

68------


14/21

REVISION: NCM119-SM

Page 12 of 19

Hydraulic oil s HLPD with detergent addi tives according to DIN 51524 / nj025

on mineral oil basis

Ref. no. 11 12 13 14 15

Viscosity VG22 VG32 VG46 VG68 VG100Ident. no. 1166925 1166926 116627 116628 116629

Agip OSO/D 22 OSO/D 32 OSO/D 46 OSO/D 68 OSO/D 100

ARAL Vtim DE 22 Vtim DE 32 Vtim DE 46 Vtim DE 68Basic Tronic

SAE10W-40

BECHEMHydrostar

22D

Hydrostar

32D

Hydrostar

46D

Hydrostar

68D

Hydrostar

100D

BPEnergol

HLP-D 22

Energol

HLP-D 32

Energol

HLP-D 46

Energol

HLP-D 68-----

Brugarolas HM-D 22 HM-D 32 HM-D 46 HM-D 68 -----

ESSO HLPD-oil 22 HLPD-oil 32 HLPD-oil 46 HLPD-oil 68 -----

Fuchs Europe

Lubricants

Renolin MR5

VG 22

Renolin MR5

VG 32

Renolin MR5

VG 46

Renolin MR5

VG 68

Renolin MR5

VG 100

FUCHS

LUBRITECHRenolin MR5

Renolin

MR10

Renolin

MR15

Renolin

MR20

Renolin

MR30

Mobil -----Hdraulic oil

HLPD 32

Hdraulic oil

HLPD 46

Hdraulic oil

HLPD 68-----

Shell Tellus DO 22 Tellus DO 32 Tellus DO 46 Tellus DO 68 Tellus DO100

TEXACO /

CALTEX Alcor DD 22 Alcor DD 32 Alcor DD 46 Alcor DD 68 Alcor DD 100

TotalFinaElf Azolla D 22 Azolla D 32 Azolla D 46 Azolla D 68 -----


15/21

REVISION: NCM119-SM

Page 13 of 19

Hydraulic oils HLP - biodegradable

Ref. no. 16 17 18 19

Viscosity VG 22 VG 32 VG 46 VG 68

Ident. no. 1166933 1166934 1166935 1166936 Agip Arnica S 22 Arnica S 32 Arnica S 46 Arnica S 68

ARAL Vitam EHF 22 ------ Vitam EHF 46 ------

BECHEM ------Hydrostar

HEP 32

Hydrostar

HEP 46

Hydrostar

HEP 68

Brugarolas ------ ------ Hidroscur D 46 ------

Castrol ------ ------ Carelube HES 46 ------

Castrol

industrie------

Tribol Bio Top

1448/32

Tribol Bio Top

1448/46

Tribol Bio Top

1448/68

ESSO ------ ------ Univis HEES 46 ------

Fuchs Europe

LubricantsPlantohyd 22S Plantohyd 32S Plantohyd 46S Plantohyd 68S

FUCHS

LUBRITECHEco-Hyd 22 S Eco-Hyd 32 S Eco-Hyd 46 S Eco-Hyd 68 S

Mobil ------ ------EAL Syndraulik

46------

ShellNaturelle

HF-E 15

Naturelle

HF-E 32

Naturelle

HF-E 46

Naturelle

HF-E 68

TEXACO /

CALTEX------ Hydra 32 Hydra 46 ------

TotalFinaElf ------ ------ Biohydran SE 46 ------


16/21

REVISION: NCM119-SM

Page 14 of 19

Lubricating oils CLP according to DIN 51517 / part 3 on mineral oil basis

Ref. no. 22 23 24 25 26 27 28

Viscosity VG 100 VG 150 VG 220 VG 320 VG 460 VG 680 VG 1000

Ident. no. 1166904 1166905 1166906 1166907 1166908 1166909 1166910

ARAL

Degol

BG100

Plus

Degol

BG150

Plus

Degol

BG220

Plus

Degol

BG320

Plus

Degol

BG460

Plus

Degol

BG680

Plus

------

BECHEMEco gear

100M

Eco gear

100M

Eco gear

150M

Eco gear

320M

Eco gear

460M

Eco gear

680M

BP ------Energol

GR-XF 150

Energol

GR-XF 220

Energol

GR-XF 320

Energol

GR-XF 460

Energol

GR-XF 680------

Brugarolas ------ ------

Beslux

gear

XP 220

Beslux

gear

XP 320

Beslux

gear

XP 460

Beslux

gear

XP 680

Beslux

gear

XP1000

Castrol Alpha

SP 100

Alpha

SP 150

Alpha

SP 220

Alpha

SP 320

Alpha

SP 460

Alpha

SP 680

Alpha

SP 1000

Castrol

industrie

Tribol

1100/100

Tribol

1100/150

Tribol

1100/220

Tribol

1100/320

Tribol

1100/460

Tribol

1100/680

Tribol

1100/1000

ESSOSpartan

EP 100

Spartan

EP 150

Spartan

EP 220

Spartan

EP 320

Spartan

EP 460

Spartan

EP 680------

Fuchs Europe

Lubricants

Renolin

CLP100

Plus

Renolin

CLP150

Plus

Renolin

CLP220

Plus

Renolin

CLP320

Plus

Renolin

CLP460

Plus

Renolin

CLP680

Plus

Renolin

CLP1000

PlusFUCHS

LUBRITEC

H

Gearmaster

CLP100

Gearmaster

CLP150

Gearmaster

CLP220

Gearmaster

CLP320

Gearmaster

CLP460

Gearmaster

CLP680------

MobilMobilgear

XMP100

Mobilgear

XMP150

Mobilgear

XMP220

Mobilgear

XMP320

Mobilgear

XMP460

Mobilgear

XMP680------

OPTIMOLOptigear

BM 100

Optigear

BM 150

Optigear

BM 220

Optigear

BM 320

Optigear

BM 460

Optigear

BM 680

Optigear

BM 1000

ShellOmala

F100

Omala

F150

Omala

F220

Omala

F320

Omala

F460------ ------

TEXACO /

CALTEX

Meropa

WM 100

Meropa

WM 150

Meropa

WM 220

Meropa

WM 320

Meropa

WM 460------ ------

TotalFinaEl

f------ ------

Kassilla

GMP 220

Kassilla

GMP 320

Kassilla

GMP 460------ ------


17/21

REVISION: NCM119-SM

Page 15 of 19

Lubricating oils CLP PG according to DIN 51517 / part 3 on polyglycol oil basis

Ref. no. 33 34 35 36 37 38 39

Viscosity VG 100 VG 150 VG 220 VG 320 VG 460 VG 680 VG 1000

Ident. no. 1166911 1166912 1166913 1166914 1166915 1166916 1166917

ARAL ------Degol

GS150

Degol

GS220

Degol

GS320

Degol

GS460

Degol

GS680

Degol

GS1000

BECHEM ------ ------Berusynth

EP 220

Berusynth

EP 320

Berusynth

EP 460

Berusynth

EP 680------

BP ------ ------Enersyn

SG-XP 220------

Enersyn

SG-XP 460

Enersyn

SG-XP 680------

Fuchs

Europe

Lubricants

Renolin

PG100

Renolin

PG150

Renolin

PG220

Renolin

PG320

Renolin

PG460

Renolin

PG680

Renolin

PG1000

FUCHS

LUBRITECH

Gearmaster

PG P100

Gearmaster

PG P150

Gearmaster

PG P220

Gearmaster

PG P320

Gearmaster

PG P460

Gearmaster

PG P680

Gearmaster

PG P1000

Castrol

industrie

Tribol

800/100

Tribol

800/150

Tribol

800/220

Tribol

800/320

Tribol

800/460

Tribol

800/680

Tribol

800/1000

Mobil ------ ------Glygoyle

HE220

Glygoyle

HE320

Glygoyle

HE460

Glygoyle

HE680

Glygoyle

HE1000

ESSO ------ ------Glycolube

220------

Glycolube

460------ ------

KLÜBERSyntheso

D100EP

Syntheso

D150EP

Syntheso

D220EP

Syntheso

D320EP

Syntheso

D460EP

Syntheso

D680EP

Syntheso

D1000EP


18/21

REVISION: NCM119-SM

Page 16 of 19

Lubricating greases

Base oil: Mineral oil Saponification agent: Lithium Temperature range: -20 to +120 deg C.

DIN 51502 K2K-20 K3K-20 KP2K-20 KP3K-20

Ref. no. 50 51 55 56Ident. no. 1166900 1166901 307906 1166903

Agip GR MU 2 GR MU 3 GR MU / EP 2 GR MU / EP 3

ARAL Aralub HL 2 Aralub HL 3 Aralub HLP 2 Aralub HLP 3

BECHEM Rhus LZ-2 Rhus LZ-3 Rhus LZ-2 Rhus LZ-3

BP Energrease LS2 Energrease LS3Energrease

LS-EP2

Energrease

LS-EP3

Brugarolas G.A.No. 80 G.A.No. 95 G.A.No. 850 EP2 G.A.No. 850 EP3

Castrol Spheerol AP 2 Spheerol AP 3 Spheerol EPL-2 ------

ESSO Beacon 2 Beacon 3 Beacon EP2 ------

Fuchs Europe

LubricantsRenolit FWA160 Renolit FWA220 Renolit FEP2 Renolit FEP3

FUCHS

LUBRITECH

Lagermeister

EP2Stabyl L 120

Lagermeister

EP2Stabyl L 120

KLÜBER Centoplex 2 Centoplex 3 Centoplex 2EP ------

KRAFFT KL-2 KL-3 KEP-2 KEP-3

Mobil Mobilux 2 Mobilux 3 Mobilux EP2Mobilgrease XHP

103

OPTIMOL Olit 2EP Olit 3EP Olista Longtime2 Olista Longtime3

Shell Alvania G2 Alvania G3 Alvania EP(LF)2 ------TEXACO /

CALTEXMultifax 20 Multifax RSP Multifax EP 2 Multifax EP 3

TotalFinaElf MULTIS 2 MULTIS 3 MULTIS EP2 MULTIS EP3

TRIBOL 3030/100-2 ------ 3030/1000-2 ------


19/21

REVISION: NCM119-SM

Page 17 of 19

Lubricating greases Lubricating greases G

Base oil:

Saponification agent:

Temperature range:

Mineral oil

Lithium complex

-20 to +140℃

Mineral oil/ ester/PAO

Polyurea

-20 to +180℃

Mineral oil

Lithium/ Lithium complex

-20 to +120℃

DIN 51502 KP2N-20 KP2R-20 GP0G(K)-10 GP00G(K)-10

Ref. no. 60 61 65 66

Ident. no. 1166930 1166937 307931 1166932

Agip Autol Top 2000

High Temp------

Autol Top

2000 Type 0

Autol Top 2000

Type 00

ARAL Aralub MKL 2 Aralub SPU2Fluid grease

AN0Fluid MFL00

BECHEMBeruplex

LI-EP2

Berutox FH 28 EPK 2

Rhus gear

grease GF

525

Rhus gear

grease GF 550

BPEnergrease

LC2------

Energrease

ZS 0

Energrease

LS-EP 00

Brugarolas G.A. Plex 2G. Beslux complex

M-2

G.A.No. 850

EP0

G.A.No. 850

EP00

Castrol Spheerol EPL2 ------ ------

CLS Grease

(Li/Ca

complex)

ESSO Ronex MP-D ------ KL-3 ------

Fuchs RenolinDuraples EP2

Renolit PU-FH300 RenolitGFW 00

RenolitGFW 00

FUCHS

LUBRITECHUrethyn MP2 Urethyn MP2

Gearmaster

LI 400

Notropeen

LXG 00

KLÜBERMicrolube

GL262

Stabutherm GH 461

(K1S-20)

Microlube

GB0

Microlube

GB00

KRAFFTKL-Complex

150------ KEP-0 KEP-00

MobilMobilgrease

XHP222------ ------

Mobilux

EP 004

OPTIMOL ------ Firetemp XT 2 Longtime PD0Longtime

PD00

Shell Retinax LX2 Stamina EP 2 ------ Alvania

GL 00(Li)

TEXACO / CALTEX Starplex 2 Black Pearl Grease 2 Multifax EP 0Multifax 6833

EP 00

TotalFinaElfMULTIS

Complex EP2------ MULTIS EP0 MULTIS EP00

TRIBOL

Molub-Alloy

4020/220-2 Tribol 9540-2

Tribol

3020/1000-0

Tribol

3020/1000-00


20/21

REVISION: NCM119-SM

Page 18 of 19

Wire rope lubricants Chain oils

External lubricant

for ropesMineral oil Biodegradable oil Synthetic oil

Ref. no. 71 73 74 75Viscosity ------ VG 100 VG 100 VG 100

Ident. no. 1166851 1166852 1166853 1166854

Agip Fin 332 EXIDIA 100PRECIS SGT

100 BIOBLASIA SX 100

ARAL Aralub MKA-Z1 Deganit B100 Deganit BA Deganit HAT260

BECHEMBerufluid Nocor

2Berumoly P 73 ------

Berufluid OP

(265mm2/s)

BP Energrease 0G ------ ------ ------

Brugarolas

Beslux Crown

H-1/R

Beslux Camin

100

Beslux Hidro-Bio

150

Beslux Ramca

100

FuchsDuotac gear

wheel sprayRenotac 343

Plantotac

HV 100NRenolin E 150

FUCHS

LUBRITECHCeplattyn 300 Stabylan 2001 Stabylan ECO 20 Stabylan 5000

KLÜBERGrafloscon

A-G1 UltraStructovis FHD

Klüberbio

CA 2-100

Klübersynth

CH 2-100

KRAFFT Q-3 4612SUPER

KROIL-MR------ LUBECER

Mobil Mobilarma 798 ------ ------ ------

OPTIMOL Viscogen 4 ------ Viscogen BS 100 Viscogen KL9

Shell Malleus OGH ------ ------Cassida Chain

150

TEXACO /

CALTEX

Talcor SWR

Compound

Talcor Chain Oil

SPTalcor CBR Fluid

Talcor Chain

Lube NF

TotalFinaElf Copai GEP2 ------ ------ ------

TRIBOL Molub-Alloy 909 Tribol 1730/100Tribol Bio Top

1428/150

Tribol 1430


21/21

REVISION: NCM119-SM

Page 19 of 19

Special lubr icants for machines from SINOMA

Grease spraying lubrication (girth gear dr ive units)

Ref. no. Ident. no. KLÜBERFUCHS

LUBRITECH

90 1166875

Priming lubricants

application by hand

(brush or spatula)

Grafloscon

A-G 1 UltraCeplattyn 300

91 1166882 Running-in lubricantGrafloscon

B-SG 00 UltraCeplattyn RN

92 1166883 Operating lubricantGrafloscon

C-SG 0 Ultra

Ceplattyn

KG 10 HMF

93 1219857 Operating lubricantfrom +5℃ +120℃

GraflosconC-SG 1000 Ultra

CeplattynKG 10 HMF-1000

94 1219858Operating lubricant

from +15℃ +120℃

Grafloscon

C-SG 2000 Ultra

Ceplattyn

KG 10 HMF-2500

Splash lubrication, oil ci rculation lubr ication (girth gear drive units)

Ref. no. Ident. no. KLÜBERFUCHS

LUBRITECH

95 1166884 Running-in lubricantKlüberfluid

B-F 1 Ultra-----


from –15 ℃ to +90 ℃

Klüberfluid

C-F 1 UltraCeplattyn 100MV


from +5 ℃ to +120 ℃

Klüberfluid

C-F 2 UltraCeplattyn 100HV

An alternative of the lubricants with the reference numbers 92 and 97 is the reference number

101 that is also permitted for grease spraying lubrication or splash lubrication for girth gear drive

units.

Observe the instructions of the lubricant supplier when this lubricant is used.During the assembly time, also Klüberfluid C-F 3 Ultra can be used as priming lubricant. This

lubricant is manually applied on girth gear and pinion.

Girth gear dr ive uni ts(see also reference numbers 92 and 97)

Ref. no. Ident. no. KLÜBER

101 -Operating lubricant

from +5 ℃ to +120 ℃ Klüberfluid C-F 3 Ultra

raw mill supplement manual

Documents