recessed linear light fixture mounting instructions for ... line voltage... · 120-277 or 347vac...
TRANSCRIPT
Installation InstructionsLVLYXX
120-277 or 347VAC Recessed Linear Light Fixture
GlowbackLED®
16409 NW 8th Ave Miami Gardens, FL 33169 1-800-679-4902 • [email protected]
GlowbackLED® is a registered trademark of Bluegate Inc ©2018 Bluegate Inc. All Rights Reserved
Specifications subject to change without notice
WARNING! Luminaire must be installed by a qualified electrician. Refer to local codes for proper installation. To prevent shock discon-nect power before installation on service.
Fixture Dimension Required Opening Weight
2” x 3” x 24” 2¼” x 3¼” x 24¼”
2¼” x 3¼” x 46¼”
2¼” x 3¼” x 68¼”
2¼” x 3¼” x 90¼”
3¼” x 3¼” x 24¼”
3¼” x 3¼” x 46¼”
3¼” x 3¼” x 68¼”
5 Lbs
7 Lbs
9 Lbs
12 Lbs
6 Lbs
9 Lbs
12 Lbs
14 Lbs
7 Lbs
10 Lbs
14 Lbs
17 Lbs
2” x 3” x 46”
2” x 3” x 68”
2” x 3” x 90”
3” x 3” x 24”
3” x 3” x 46”
3” x 3” x 68”
3” x 3” x 90”
4” x 3” x 24”
4” x 3” x 46”
4” x 3” x 68”
4” x 3” x 90”
2ft Y23
4ft Y23
6ft Y23
8ft Y23
2ft Y33
4ft Y33
6ft Y33
8ft Y33
2ft Y43
4ft Y43
6ft Y43
8ft Y43
3¼” x 3¼” x 90¼”
4¼” x 3¼” x 24¼”
4¼” x 3¼” x 46¼”
4¼” x 3¼” x 68¼”
4¼” x 3¼” x 90¼”
2.875”
3.938”
2.875”
2.938”
2.875”
1.938”
Y23 Y33 Y43 & Y43C
Light Fixture
Direct Screw Installation
Twist Clip Installation
Trimless Installation
Drop-Ceiling Installation
Required Opening Size
Installation InstructionsLVLYXX
120-277 or 347VAC Recessed Linear Light Fixture
GlowbackLED®
16409 NW 8th Ave Miami Gardens, FL 33169 1-800-679-4902 • [email protected]
GlowbackLED® is a registered trademark of Bluegate Inc ©2018 Bluegate Inc. All Rights Reserved
Specifications subject to change without notice
Direct Screw Installation
Framing Mounting Screw
Drywall
Light Fixture
1 2 3
5
Pass mounting screws through light fix-ture housing using pre-drilled mounting holes on rear of housing.
Secure light fixture housing to framing using screws suitable to your installation type. #6 Screw Reccommended
Lift and connect inner channel using pro-vided connectors. Refer to inner-channel assembly notes for detailed instructions.
Reccomended Installation Method!
Framing Required! Build framing on sides and top of light fixture for support. Create Opening: Refer to chart on Page 1 for re-quired opening size. Type IC: Suitable for IC contact.
Inherently Protected
4
Once the inner channel has been prop-erly connectec and installed. Snap lens into place.
Make electrical connections once light fixture installation is complete. Refer to the wiring diagram, for detailed instructions for making electrical connections.
Lift and connect inner channel using pro-vided connectors. Refer to inner-channel assembly notes for detailed instructions.
Twist Clip Mounting: Specialized clip secures light fixture to drywall. Create Opening: Refer to chart on Page 1 for re-quired opening size. Type IC: Suitable for IC contact.
Inherently Protected
Installation Instructions
LVLYXX 120-277 or 347VAC Recessed Linear Light Fixture
GlowbackLED®
16409 NW 8th Ave Miami Gardens, FL 33169 1-800-679-4902 • [email protected]
GlowbackLED® is a registered trademark of Bluegate Inc ©2018 Bluegate Inc. All Rights Reserved
Specifications subject to change without notice
Twist-Clip Installation
Twist Clip
Clip Screw
Drywall
Light FixtureLight Fixture
Make electrical connections once light fix-ture installation is complete. Refer to the wiring diagram, for detailed instructions for making electrical connections.
1
4
2
5
3
6
Pass twist clip bolts through pre-drilled holes on rear of rear of light fixture housing.
When clip is engaged. It will open up behind drywall to secure light fixture in place.
Twist clip bolts pass through rear of housing and are fed through
twist clip. Light fixtrure is lifted into cavity with clips hugging the side of the body
of the light fixture.
Once light fixture is lifted into place. Use a screw-driver to engage bolt. As bolt is tightened, the light fix-ture will grip onto drywall.
Installation Instructions
LVLYXX 120-277 or 347VAC Recessed Linear Light Fixture
GlowbackLED®
16409 NW 8th Ave Miami Gardens, FL 33169 1-800-679-4902 • [email protected]
GlowbackLED® is a registered trademark of Bluegate Inc ©2018 Bluegate Inc. All Rights Reserved
Specifications subject to change without notice
Drop Ceiling Installation
Ceiling Grid T-Grid Set Screw Light Fixture
Ceiling Tile
Grid Bracket
Light Fixture
Adjust Here
1 2 3
Adjust grid bracket as needed to acco-modate your grid structure using the screws shown.
Drop light fixture down into the opening that was created when ceiling structure was built. Make sure light fixture sits flat and grid brackets go over grid structure.
Secure light fixture to grid structure using provided set screws.
Adjustable Grid-Bracket: Adaptable to any grid structure and configuration. Opening: Refer to chart on Page 1 for required opening size. Opening created using grid-structure. Suspension: Grid system must be suspended from ceiling and able to support weights listed on Page 1. Type IC: Suitable for IC contact.
Inherently Protected
4
Once light fixture is secured to grid structures make electrical connections. Refer to the wiring diagram, for de-tailed powering instructions.
Framing Required! Build framing on either side of light fixture. Create Opening: Refer to chart on Page 1 for re-quired opening size. Screw Spacing: Mounting screws are required every 16” on center. #6 Screw ReccomendedType IC: Suitable for IC contact.
Inherently Protected
Installation Instructions
LVLYXX 120-277 or 347VAC Recessed Linear Light Fixture
GlowbackLED®
16409 NW 8th Ave Miami Gardens, FL 33169 1-800-679-4902 • [email protected]
GlowbackLED® is a registered trademark of Bluegate Inc ©2018 Bluegate Inc. All Rights Reserved
Specifications subject to change without notice
Twist-Clip Installation
Fram
ing
Mounting Screws
Light Fixture
Drywall
Plaster
Light FixtureLight Fixture
Drywall Tape
Contractor Tape
1
54
2 3
Mounting screws are passed through pre-drilled holes on plaster bead attached to the side of the light fixture housing.
Use compound knife for a smooth finish. Sand, paint, and finish all drywall work before removing contractor’s tape.Make electrical connections (See page 6)
Prepare Light Fixture for Plaster Work: Apply single layer of contractor’s tape to channel opening (if lens removed), or lens. Do not use multiple layers of tape. If cover-ing channel opening, make sure to cover area where lens snaps into place. Plaster Preperation: Apply single layer of drywall tape over plaster bead to avoid crack-ing. Plaster Notes: For areas experiencing regular vibration (by doors) use Durabond to avoid cracking.
DO NOT USE “Soft-Mud” (Pre-Mixed Joint Compound)
Counter-Sink flat head screws so screws sit flush with the integrated
bead.
Once light fixture has been secured to ceiling and framing, plas-ter-work can begin for trimless installa-tion look.
Installation Instructions
LVLYXX 120-277 or 347VAC Recessed Linear Light Fixture
GlowbackLED®
16409 NW 8th Ave Miami Gardens, FL 33169 1-800-679-4902 • [email protected]
GlowbackLED® is a registered trademark of Bluegate Inc ©2018 Bluegate Inc. All Rights Reserved
Specifications subject to change without notice
Linking Plate
Hex Key
Linkable Connector
Inner Channel
Inner Channel
Set screw
Hex Key
Linkable/Continous Run Connections
Inner Clip Connection
Use linking plate, linkable connectors, and hex key to acheive continous runs. Firmly insert male connector from one fixture to the next
Using provided hex-key, secure linking plate to both light fixtures. Insert inner channel and lens once electrical connectins have been made.
PINCH!
“CLICK!!!”1 2 3
Pinch the tabs at the bottom of the inner clips.
Drop light fixture down into the opening that was created when ceiling structure was built. Make sure light fixture sits flat and grid brackets go over grid structure.
Drop light fixture down into the opening that was created when ceiling structure was built. Make sure light fixture sits flat and grid brackets go over grid structure.
Make sure that every clip is engaged and resting in its locked position.
Before inserting in-ner-channel be sure to make electrical connec-tions using the provided connectors. Connection should be secure.
Installation Instructions
LVLYXX 120-277 or 347VAC Recessed Linear Light Fixture
GlowbackLED®
16409 NW 8th Ave Miami Gardens, FL 33169 1-800-679-4902 • [email protected]
GlowbackLED® is a registered trademark of Bluegate Inc ©2018 Bluegate Inc. All Rights Reserved
Specifications subject to change without notice
Power-Feed Entry and Electrical Connections
Non-Dimmable Configuration
Dimmable Configuration
Encap Power EntryAcess electrical using knockouts on endcap.
Rear Power EntryAcess electrical using knockouts on rear of light fixture (2).
White | Neutral
Purple | Dim +
Gray | Dim -Green | Ground
Black | Line Internal Driver
On
Off
Light Fixture
Dimming wires capped when not in use
White | NeutralPurple | Dim +
Gray | Dim -Green | Ground
Black | Line Internal Driver
0-10V Dimmer
Light Fixture
0-10V Dimmable Standard | Other Controls Available
Note: For Emergency Back-Up, Follow Battery Manufacturer Instructions