Operation andMaintenance Manual

3628336241

TABLE OF CONTENTS

Warranty Information ................... 2

Safety Information ..................... 3

Safety Features ......................... 3

Important Installation Instructions ....... 3Pre Installation Checklist .............. 46

Adjustments .......................... 7=8

Programming the Remote Control ..... 89

Installing Lightbulb and Lens ............ 9Scheduled Maintenance ............... 10

Troubleshooting Guide ............. 1011

Wiring Diagram ........................ 12

Parts Lists and Exploded Views ...... 1213Accessories ............................ 14

COMPLETE WITH mNTELLlCODE

REMOTE CONTROL AND SERIES li

For up to 7'-6" tall Doors. (Extension Kit avaimable for 8' Doors)

included Wail Control MUST be installed prior to Operation ofthis Garage Door Operator.

Safe-T-Beam ®Safety Reverse System Must be installed andthe Force Controls MUST be Properly Set to close door.

This Equipment meets or exceeds all Federal, State and UL325

THEGEN|ECOMPANYLIMITEDWARPJ ,NTYWhat is coveted?

Any defect [n material and product workmanship from personal, normalhousehold use [n accordance with the Owner's Manual.

For how long?

MODEL2560... 1Syears on motor, 3years all other parts.MODEL3560... Lifetime' on motor,3 years all other parts.

%[fedme=Aslong dsyou own your home.

Who gets the warranty?

This warranty is limited to the consumer who originally purchasedthe product.

Geographic scope:

This warranty applies only to units installed and operated within the countrywhere they were purchased.

Limitations:

IMPLIEDWARRANTIES,INCLUDINGTHOSEOF FITNESSFORA PARTICULARPURPOSEANDMERCHANTABILITY(ANUNWRITTENWT_RRANTYTHATTHEPRODUCTISFITFORORDINARYUSE)ARELIMITEDTOONEYEARFROMTHEDATEOF PURCHASE.GENIEWILL NOT PAYFOR:LOSSOFTIME;INCONVENIENCE;LOSSOF USEOFYOURGENIEPRODUCTORPROPERTYDAMAGECAUSEDBYYOURGENIEPRODUCTORITSFAILURETO WORK;ANYSPECIAL,INCIDENTALOR CONSEQUENTIALDAMAGES;ORANY DAMAGESRESULTINGFROMMISUSEORMODIFICATIONOF YOURGENIEPRODUCT.

Somestates and provinces do not allow limitations on how long an impliedwarranty lasts or the exclusion of incidental or consequential damages, sotheabove limitations or exclusions may not apply to you.

This warranty is the only one we will give on your Genie product, and it setsforth all our responsibilities regarding your Genie product.There areno otherexpresswarranties.

Stateand province rights:This warranty givesyou specific legal rights,and youmayalso have other rights which vary from state to state and province toprovince.

How to get warranty service:

To obtain warranty service for your Genie product, you must provide proof ofthe date and place of purchase of the product.

1. Do-It=Yourself-Service.

Call the Genie Customer Servicetoll free at 1.800.354.3643to speak inperson to a trained Genie representative for assistance in diagnosing theproblem and arranging to supply you with the required parts for do-it-yourself repairs.Trained servicerepresentatives areavailable Monday-Friday,8:00a.rn.- 9:00 p.m.,EasternTime,and on Saturday, 10:00a.m.to 7:00 p.rn,EasternTime (subject to holidays) You may also get the information youneed at www.geniecompony.com.

2,Service From Authorized Dealers.

Youalsomayobtainwarrantyservicefrom GenieauthorizeddealersbycallingtheGenieCustomerServiceat 1.800.354.3643or byvisitingw_geniecomporry.combeforeschedulingwarrantyservice.Ifwarrantyserviceisprovidedby anauthorizeddealer,Geniewilt provideall requiredpartsunderwarrantyat nochargeto you,butthe dealersareindependentbusinesspeopleandmayrendera benchor servicecallchargefor thek services.Geniewill notreimburseyouor otherwisebe responsibleforthosecharges.

Wesuggestthat youretainyour originalpackingmaterialinthe eventwe choosetorepairor replaceyourGenieProductandrequestthat you shipit to us.Besuretoincludeyour name,address,telephonenumber,proof of dateandplaceof purchaseanda descriptionof the operatingproblem.Afterrepairingor replacing,yourGenieproduct,we will shipit to your homeat no costto youfor partsandlabor,but youwillhaveto paya minimumof $5.00for shippingandhandlingcharges.

Yourchoiceof eitherone of the above-describedserviceoptionsisyourexclusiveremedyunderthis warranty.

What this warranty does not cover:

Thiswarrantydoesnot coverbatteries(whichareconsideredreplaceableparts),installation,commercialuse,defectsresultingfrom accidents,damagewhile in transittoourservicelocationor damageresultingfrom alterations,misuseorabuse,lackof propermaintenance,unauthorizedrepairor modificationof the product,affixingof anyattachmentnot providedwith the product,programmingof the RemoteControlDevices,Safe-T-Beam®adjustment/cleaning,staplesthrough wiring,pinchedor brokenwires,Carriagedisengaged,ForceContro!adjustments,door out of balance,brokenspringsorcables,poweroutages,useof extensioncords,missingor damagedpartsondiscounted,clearanced,final saleor taped cartons,phantomoperations(laborisnotcoveredif Openerisfunctioning properlywhile technicianis in garage),fire,flood,oractsof God,or otherfailureto followthe Owner'sManual

Please note the following information,soit is available if youneed to call us.

Date Purchased / /

Serial Number

Operator ModelRemote Control Model

Model Number andSerial Number are

located on front panelinside the lens,

jj_

}

/./

j_

WK YR P [

27 94 4 H

Serial/Mfg No.

Pleasekeep original or photocopy of your sales receiptwith this manual for future reference should serviceever be requiredo

INCLUDED IN THIS PACKAGE

Manual 1)Warranty Information2) Pre Installation Checklist to be reviewed prior

to any assembly or installation3) Necessary Adjustments4) Programming Remote Devices5) Maintenance and Troubleshooting6) PartsExplosions7)AccessoryOrder Form8) Door Opener Association Safety and

Maintenance Brochure (DASMA)

9) Entrapment Warning Label =To be Adhered inclose proximity to wall control

Poster 1) Pictorial and step by step opener assemblyinstructions

2) Pictorial and step by step opener installationinstructions

iT IS CRITICAL THAT ALL SAFETY WARNINGSMARKED CLEARLY [N BOTH THE MANUAL

AND POSTER ARE READ, UNDERSTOOD ANDFOLLOWED.

Visit Our Website at: www.geniecompany.comFORANSWERS,"CALL 1,800,354,3643

SAVETHESE INSTRUCTIONS

2 For Help, call 1=8OO-35-GENIE or visit www.geniecompanyocom

OVERVIEW OF POTENTIAL HAZARDSOverhead doors are large,heavy objects that move with the help of springs under high tension and electric motors. Sincemoving objects, springs undertension,and electric motors can causeinjuries, your safetyand the safetyof others depend onyou reading the information in this manual. Ifyou havequestions or do not understand the information presented, callThe Genie Company. or your local Genie Distributor.

Hnthis section, and those that follow, the words Danger, Warning and Caution are used to emphasize important safetyinformation. The word:

_, DANGER; indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.

A WARNING; indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.

A CAUTION; indicates a potentially hazardous situation which, if not avoided, may result in injury or property damage.

The word NOTE is used to indicate important steps to be followed or important considerations.

POTENTIALHAZARD

MOVINGDOOR

ELECTRICALSHOCK

HIGHSPRINGTENSION

EFFECT

WARNING:Could result in death

or serious injury.

WARNING:Could result in death

or serious injury.

WARNING:Could result in death

or serious iniury.

PREVENTION

Keep people clear of opening while door is moving.

o Do Not allow children to play with the door operator.

Do Not operate a door that jams or one that has a broken spring.

oTurn off power before removing operator cover.

oWhen replacing cover, make sure wires are not pinched or nearmowng parts.

o Operator must be properly grounded.

oDo Not try to remove, repair or adjust springs or anything towhich door spring parts are fastened, such as, wood blocks,steel brackets, cables or other like items,

o Repairs and adjustments must be made by a trained doorsystem technician using proper tools and instructions,

MPORTANT INSTALLATIONNSTRUCTIONS

zLWARNING:TO REDUCETHERISKOFSEVEREINJURYOR DEATH:

1 READAND FOLLOW ALL SAFETY.INSTALLATIONANDOPERATIONINSTRUCTIONS.If you have anyquestions or do not understand an instruction, callyour authorized Genie installation professional.

2 Do Not install operator on an improperly balanceddoor. An improperly balanced door couN causesevere injury. Repairs and adjustments to cables,spring assembly, and other Hardware must be madeby a trained service person using proper tools andinstructions.

3 Remove all ropes, and disable all locks connected tothe door before installing operator.

4 tnstall door operator 7 feet or more above the floor.Mount the emergency release knob 6 feet abovethe floor.

5 Oo Not connect the operator to the source of poweruntil instructed to do so.

5 Locate the control button:

[ Within sight of door,At a minimum height of,5 feet so small childrencannot reach it_

, Away from all moving parts of the door.7 Install the entrapment WARNING labet next to the

wal button or console. Install the emergency releasetag on, or next to, the emergency release

8 The operator must reverse when the door contacts a1-1/2 inch high object on the floor at the, cen!er ofthe doorway[This is about the sizeof a 2 x 4 boardlaid flat.

SAFETY FEATURES

Safe-T-Beam ® (STB) Non-Contact Reversing SystemPlaces an invisible beam across door opening, that reversesthe door during down travel to the fully open position ifanything passes through beam.

Safe-T-Reverse ® Contact Reversing SystemAutomatically stops and reverses a closing door within 2seconds of contact with an object.

Safe-T-Stop ® Timed Reversed SystemAutomatically opens a closing door, if door does not closewithin 30 seconds,

ForceGuard ® Control

Used to set the force required for opening and closingdoor. For maximum safety, set the minimum force requiredto fully open and close door.

Automatic Lighting SystemLight bulbs up to 60 Watts max., used for safer entries andexits, The lights turn on when door is activated andautomatically turn off 4,5 minutes later.

Manual Emergency ReleaseAllows the garage door to be opened or closed manuallyfor emergencies or maintenance,

For Help, ca!l 1-800-35-GENIE or visit wwwogeniecompany,¢ora 3

PRE-INSTALLATiON CHECKUSTThis Opener includes parts and supplies needed to install in mostgaragesand connect to most garage doors. There are many variationsof garages and garage doors, A few additional parts and supplies maybe needed to install Opener into your garage and connect to yourgarage door. While checking items listed below, note any additionalitems you will need,Tools used in this section:12'+Tape Measure • Pendl • Ladder • Level

Check following items before assembling Opener:

CHECK DOOR CONDiTiON AND

THICKNESS

Check condition of vertical stile in center of door, and its connection todoor's top and bottom beams. (Figure 2)

A If door frame is nailed together and not a solid connection, doorframe must be braced or reinforced before installing Opener,

B If door is'lightweight" (made with frame and skin- not solid),door (including door frame) must be braced or reinforced beforeinstalling Opener.

C A door opener reinforcement bracket may also be needed toconnect garage door to Opener's Door Bracket. This Opener isdesigned for instalIation on a proper{y braced sectional door orsolidly braced one-piece door.

D Contact your Genie Factory Authorized Dealer or dealer of yourgarage door for any necessarybracing and a door openerreinforcement bracket (if needed) before proceeding.

E If you have a wooden door, measuredoor's thickness. If your dooris lessthan 2"thick, brace door or useshorter Door Bracket Lag Screws(1/4" x I-I/4" - not included)

CHECK GARAGE DOOR

ALIGNMENT_ OPERATION_AND BALANCE

A Raisedoor, check alignment and see if it moves freely (Figure 1). Ifdoor appearsout of alignment, binds, or does not move smoothly,contact a Genie Factory Authorized Dealer or dealer of your garagedoor for repairs and adjustments to door mechanism,

B Raisedoor to 3' - 4' above ground and carefully let go, Doorshould stay stationary. Slight movement is acceptable, More thanslight movement means door is out of balance, Contact a GenieFactory Authorized Dealer or dealer of your garagedoor for repairs and adjustments to door mechanism,

KEEP FEET CLEAR OF DOOR

Sectional _ _q--_j' _ One-PieceDoor _ - Door

Figure 1 Checking door balance

C Check door type. Make a note of whether it is a sectional or a one-)iece door for reference later (Figure 2).

Ifyour door Sticks,binds,or isout of balance,have it adjustedbya Genie Factory Authorized Dealer. Door springs, cables,pulleys, brackets and associatedhardware are under extremetension and can Causeserious injury or death.

SECTIONAL DOOR, TORSION SPRINGS SECTIONAL DOOR, EXTENSION SPRINGS

J'_;:>" Extension

Center "::::-_] :: I]

q_: ]]

ONE-PIECE DOOR, TRACKLESS

Header Area

Center Stile

Figure 2 Note DoorType

MEASUREGARAGEDoor HBGHT

Measuredoor height (floor to top of door) using a tape measure.

This new Garage Door Opener is designed for doors up to andincluding 7'6" tail. If door height is 7'6" or lesscontinue to Check Step 4.

C If door height is 8'-0'_you need a Rail Extension Kit. (Figure 3).

(SeeAccessoriesOrder Form,Page 14).

D If the door height is taller than 8'-0", the opener you purchased isthe wrong version.Contact your Customer Service Representativeat 1-800-354-3643.

E×,eos oofor8"door

@m-- _ ---e

l__ Figure 3 Rail Extension Kit

AB

CHECK DOOR HEADER AREA

The header is a heavily reinforced section of the wall justabove the top of the garage door opening.

A Find vertical center line of door and header:Close door.

Measuredoor width at top.Mark a point at center of door and on header directlyabove door. Draw a center line to connect points.

B Find Header Bracket mounting height (Figure 4): (Donot attachHeader Bracket).

Raisedoor, watching top edge of door and stop doorwhen its edge reaches its highest point.

Measuredistance ("H") from top edge of door to floor.

Forsectional doors, add 2-1/2" to "H': Mark a pointon center line. Bottom of Header Bracket wiII beinstalled here.

Forone-piece doors, add 6" to'H': Mark this point oncenter line. Bottom of Header BracketwiII beinstalled here.

SECTIONAL DOOR ONE-PIECE DOORH+24/2"_ _ H+d"

/ 7HEADER _IEADER

Figure 4 Find Highest Point of Trave[

4 For Help, call 1-800-35-GENIE or visit www, geniecompanyocom

o Forall types and stylesof doors:- ff the ceiling ,inyour garage is so low that there isnot at least a 3 space above the Header Bracketmountingpolnt, contact a Genie FactoryAuthorizedDealer.

If a door spring is in the way, place the Header Bracketabove the spring. Do Not move the door spring.

Door springsare under extremely hishould be handled ONLY by a trained professional. I

C Check wall for a stud or a solid header at your mark: (Ifchecking afinished waJi,a stud finder may be helpful).

, If location isabove Header,a 2" x 6" board must bescrewed to studs beside your mark with at least two LagScrewsand Flat W'ashers(not provided).

Transfer your mark to new mounting board.

CHECK POWER HEAD

MOUNTING AREA

Check ceiling or space above where Opener Power Head will bemounted (Figure 5): There must be a 120Volt grounded outlet orwiring box within 3 feet of Power Head.

outlet

(7'-6"door

Door Center Line

Figure 5 Check Power Head location

A The measurements above are taken from the garagedoorcenterJine toward the rear of the garage.

B Find location of ceiling joist or truss above where Opener PowerHeadwill be and estimate type and quantity of materials needed foryour installation (Figure 5A & B).

MOUNTING EXAMPLES

Perforated Angle Iron Conduit

Figure5A

OPENCEILINGSStrapsand angle iron may attach directly to joistsor trusses.

Wood

For HeJp, can 1-800-35-GENIE or visit www,geniecompany,¢om

Perforated StrapsFiNiSHED CEILINGS

Locateceiling joists or trusses usinga stud finder or similar device.

Attach angle iron(not included) tojoistsor trusses through finishmaterial using Lag Screws.

Figure 6B

CHECK CEmLmNG FOR GROUNDED

PowER SOURCE

A Check that there is a 15Amp 120Volt grounded electricaloutlet or grounded permanent wiring box (per building code)within 3'of Opener Power Head:Figure 5

• If not, an outlet or wiring box must be installed. Contacta licensed electrician for installation.

• If building codes require permanent wiring, Power Headmust be partially disassembled to install appropriatewiring in placeof Power Cord. (SeeAssembly andInstallation Poster.)

Permanent wiring must be installed by a LicensedEmectri¢ian. Not all Genie Factory Authorized Dealersare Licensed Electrician's. Contact someone who is aLicensed Electrician.

WARNING •0Do Not use an extension cord! Extension cords can

De Net use portable generator! This product isdesigned to operate using standard house current.DeNot use alternate power supplies,

MOUNTmNG BRACKET LOCATmON

Check for wood garage frame, jamb, or masonry at mounting[ocation (6" above floor) with attachment tabs facing awayfrom garage door (Figure 7L

A If you cannot mount Safe-T-Beam _ Mounting Bracket towood frame:

Concrete screws and concrete anchors (not incHuded)must be used to mount Brackets on masonry with

attachment tabs facing away from garage door.

Source

Sensor .,d_-,, _-

Safe-T-Beam® _ Top of

Mounting Brack_/_ !.. Bracket @'aboveFigure,Mount,ng

Safe_T_Beam® _ floor

Components

RECOMMENDED TOOLS

A

BTools (Figure 8):

Additional took to make installation easier:

Slotted and phi[Hps screw=driver bitsStud finder

Sheebmeta[ cutting snips

REMOVE EXISTING GARAGE

Door LocKsCheck that the garage door locks, rope, and T-Handles areremoved from the garage door before starting the instaHHation.

A ffyour garage does not have a separate entry door, it ishighHy recommended to install[ a Genie Emergency Release Kit(GER-2). Emergency Release Kit lets you open the garage doorfrom outside if there is a power failure. (Please see AccessoriesOrder Form on page 14.)

Before going further, get any items and tools if needed

for your installation

_7 Garage door frame reinforcement brackets,screws,bradngor reinforcement kits (dealer)

_7 Lag Screws(1-1/4") for a wood door lessthan 2" thick (store)

_7 Electrical outlet and/or wiring (supplied by a licensed electrician)

_7 Sufficient angle iron or strapping for hanging Power Head (store)

_7 60Wan light bulbs (Rough service bulbs recommended)(store)

_7 GER-2Emergency ReleaseKit for entry during power failure (store)

_7 Wood for header,ceiling, and/or door braces (store)

_7 Masonry fasteners for Safe-T-Beam€:'Bracket installation (store)

_7 Safe-T-Beam_"BracketExtensions (dealer)

_7 Masonrydri[[ bit (store)

_7 Extension Kit (for 8'Garage Doors)(dealer)

Go to Assembly and Installation Poster for fullInstallation Instructions,

I/t6" 5/32" Tape Measure_DriH Bit DriH Bit

6' or 7'Step Ladde_

Wire Phi[bps ScrewdriverStripper

AdjustaMe Wrench FUat BUade Screwdriver

/

Hammer Safety, GUasses r/l_ _-_PenciU

1/4" 5/16" 3/8" 7/16" I/2" 9/16"Sockets

Hack Saw Wrench

IMPORTANTSAFETY INSTRUCTIONS

SEVERE INJURY OR DEATH1 READANDFOLLOWALLINSTRUCTIONS.

2 Neverlet childrenoperateor playwith the DoorControls,KeeptheRemoteControlawayfromchildren.

3 Alwayskeepthe movingdoor in sightandawayfrom peopleandobjectsuntil the door iscompletelyclosed.NOONESHOULDCROSS]HEPATHOFAMOVINGDOOR.

4 NEVERGOUNDERASTOPPED.PARTIALLYOPENDOOR.

5 TestOpenermonthly.Thedoo_MUSTreverseon contactwitha lq/2 highobject(ora2 x4 board[aidflat)atthecenterofthedoorway'onthe floor. Afteradjustingeitherthe Forceor the Limitof traveLretestthe Door Opener.Failureto adjustthe Openerproperlymaycausesevereinjuryor death.

7 KEEPGARAGEDOORSPROPERL_BALANCED.SeeOwner'sManual.An improperlybalanceddoor increasesthe riskof severeinjury oFdeath. HaveaGenieFactoryAuthorizedDealermake'epaksto cablesspringassembliesandother hardware.

8 SAVETHESEINSTRUCTIONS.

NOTES, REMINDERS

Carpenter's LeveU

Figure 8 Recommended Tools6 For Help, call 1-800-35-GENIE or visit www, geniecompanyocom

MAmNTENANCE AND ADJUSTMENTS

ADJUSTING LiMiT SWITCHESAND FORCE CONTROLS

WARNING:• A moving garage door can cause senous injury or death.

Keepthe path dear.o Position the ladder to the side of the Power Head so it is

clear of aHmoving parts of the Opener and the door.

o Set the door Opener to use the minimum force neededto open the door,

A CLOSE ADJUSTMENT

On front pane[ of Power Head find adjusting screwmarked "CLOSE" (Figure MA-1).

, Gently turn screw counterclockwise until it stops.- Very little force is required to turn adjusting screw.Press Wall Console to chose garage door.- Observe if door stops at "CLOSE" limit switch.

(Figure MA-2). If door is fully closed--adjustment isfinished. Go to "OPEN" Adjustment.

- If door stops but is not fully closed,a. Measure distance between bottom of door

and floor.b. Move"CLOSE"Limit Switch that same distance

toward door.

- If door stops and/or reverses before reaching the"CLOSE" Limit Switch

a. Slightly increase CLOSE Force setting (clockwise).- If door reverses after contacting floor, move Limit

Switch toward Power Head.

- If door fails to move, check Safe=T=Beam®System. SeeTroubleshooting Section, pages 10=] 1.

Tighten Limit Switch Set Screw. Do not over-tighten(strip} Limit Switch Set Screw.

B OPEN ADJUSTMENT

On front pane[ of Power Head find adjusting screwmarked "OPEN" (Figure MA-1).

, Gently turn screw counterclockwise until it stops.- Very little force is required to turn adjusting screw.Press Wall Console to open garage door.- Observe if door stops at "OPEN" limit switch.

(Figure MA=2). If door is fully open--adjustmentis finished.

- If door stops but is not fully open,a. Measure distance between bottom of door

top of door opening.b. Move"OPEN"Limit Switch that same distance

toward Power Head.

- If door stops before reaching the "OPEN" Limit Switcha. Slightly increase OPEN Force setting (clockwise).

- If door fails to move, see Troubleshooting Section,pages 10=11.

Tighten Limit Switch Set Screw. Do not over-tighten(strip) Limit Switch Set Screw.

, Cycle opener a few times to double check settings.Repeat adjustment steps as necessary.

Little effort is required to turn the ForceAdjusting Knobs.

° If the door stops moving while opening orclosing, adjust the Open Force or Close ForceControls slightly clockwise (to slightlyincrease the force) and retry the step.

. The Open Force and Close Force Controls are tobe set to the minimum force necessary toensure the door smoothly opens andcloses completely.

* Ensure the Carriage Assembly is engaged and isbetween the two Limit Switches beforeoperating the Opener.

FORCECONTROLS

Figure MA-1 Making Force Adjustments

OPEN

OPENi!

CLOSE

Figure MA-2 Making Force Adjustments

For Help, call 1-800-35-GENIE or visit wwwogeniecompany, com

f Transmitter Complance StatementTransmitters comply with al United States and Canadian legal requirements asof the dateof manufacture, No warranty is made that they comply with al UegaUrequirements of anyother jurisd'iclon. If transmitters are to be used in another country, the importer mustdetermine compUiancew4h any UocaUUawsand reguUatlonswhich may differ from UnitedStates and Canadian requirements prior to use.

Los transmisores cumplen con todas UasregUamentadones UegaUesde los Estados Unidosy deUCanad_,en Uafecha de fabricaci6n, Ninguna garantfa seda que cumplan con todasas regamentaciones legales de ninguna otrajudsdicci6n. Si los transmisores sevan autlizar err otto pais,el importador debe determinar sicumplen con las reglamentacionesy leyes locales que puedao serdiferentes alas reglamentadones de los Estados Unidos ydel Canada, antes de usar los mismos.

Les emetteurs sont conformes £ la r_gementation am@icaine et canadienne _compterde leur date de fabrication, Aucune garantie n'est stipul@ indiquant qu'Is sont conformes

toutes les prescriptions juridiques d'autres autorit_s, Si les _metteurs sont utlis_s dansd'autres pays, t incombe a I'importateur d'en d_terminer leur conformit_ aux lois et r_geslocales pouvant diff@er de celes des Ctats-Unis et du Canada avant toute utlisationdesdits 6metteurs.

Sendeger£te entsprechen alen gesetzlchen Bestimmungen in den USA und Kanada zumZeitpunkt der Herstelung.Wir Obernehmen keine Gew£hr[eistung fijr die Einha[tung a[[ergesetzlichen Bestimmungen in anderen Landem,Solen Sendeger£te in anderen L£nderneingesetzt werden, so mussder Importeur vor dem Gebrauch sicherstelen,dass dieSendeger£te auch sokhen Iokalen Bestimmungen entsprechen, wekhe yon denBestimmungen der USAund Kanadasabweichen.

£,x,l)l {_II!II __iiI I £ I?._ £ I I I _I InI _k I_ 4-1 __lSi _t£1t,_l_111°

;017l?,_!20_1-_t-_)'#,_lo)[_1c@.]1t¢'o5)tI, BI tl&l_',(0 {_/IJ/E Y_,'L0 i)] _gR$]]Z)_

niEi_O]_]E_Eke-XJ_qlA_A_ U@ #q_xb_bA_o£8_slql _Ai ujq3_ _tL_E}£_£!£

SETTING CONTACTREVERSE FUNCTION

Limit Switch and Force Adjustments must be completedbefore checking the contact reverse function (Figure _A-3).

A Open garage door usingWall Console, Figure _A-3

B Lay a 2" x 4" board fiat in centerof doorway.

C Close door using Wail Console.

Check that door stops and reverseswithin 2 seconds after itcontacts board:

, if door does not reverse, decreaseClose Force until door reverses.

, If door still does not reverse,move Limit Switch toward door.

E Check Safe-T-Beam ° Systemoperation:

, If beam is blocked, door willnot close.

2" x 4" boa rdhid fiat

ACCESSORIES

PROGRAMMING THE

REMOTE CONTROLS

, Each Remote Control must be programmedseparately.

° The Remote Controls will not cause the doorOpener to close the garage door if the Safe-T-Beam® System is malfunctioning.

° When programminc) the Remote Controls, theymust be at least 24 from the Antenna Wire.

Ifthe red Learn Indicator Light blinksapproximately 4 times per second,lrogramming has stopped. If programmingas stopped, repeat the above steps.

Each Button on a 2 or 3 Button Remote Controlis for a different Opener. You cannot use morethan one Button per Remote, per Opener.

° A maximum of seven Remote Controls orWireless Keypads can be stored into theReceiver at one time. If a Remote Control

becomes lost, or if you want to delete a RemoteControl or Wireless Keypad, see To EraseAllReceiver Memory."

A To program one Button of a Remote Control (Figure MA-4):

Locate Learn Button and Learn Indicator Lighton left side of Power Head (Figure _A-5),

Press and release Learn Button, Red Learn

Indicator Light will blink 2 times per second,

Press Remote Control Button once within 30

seconds, Red Learn Indicator Light will stay lit,

Press Remote Control Button again, Red LearnIndicator Light will go out, indicating thatmemory is stored,

Press Remote Control Button again and the doorwill operate,

B Program each additional Remote using step A above(up to seven),

To Erase AiJ Remotes from Power Head MemoryA Press and hold Learn Button on Power Head for 10

seconds or untl Learn Indicator Light goes out.Memory is erased:

Program Transmitter/Receiver again as needed.

To Replace Remote Control Battery

A FOR NON-FLASHLIGHTMODELS

Pop offthe back of the transmitter,- Use coin, pen, screwdriver or any similar device,- Replace old Battery with new coin type battery,Replace back of remote,

B FOR FLASHLIGHT MODELS

Slide open battery cover,- Replace old Battery with new AAA battery,Replace battery cover,

8 For Help, call 1-800-35-GENl£ or vBit wwwogeniecompanyocom

£ WARNING:A moving garage door may cause senous injury or death.

o Keep people dear of opemng while door is moving.Do not allow children to play with the Remote Controls,

Ufthe Safety Reverse does mot work properly:, Close the door and disconnect the Opener using the

Emergency Release Cord,

° Do not use the door Opener, Remote ControB, oJWireless Keypad.

o Refer to the door and door Opener Owner's Manualsbefore attempting any repairs.

Remote Control Operation

A Press Button on Remote Control Garage door wH[ move.

B Press Button again. Garage door wi[I stop:The door automatically stops at the end of the open orclose cycle.

C Press Button again. Garage door will reverse.

iNSTALLLUGHTBULBSAND LENsA Install two 60Watt light bulbs (not included) into LightSockets (Figure MA-6):

o Rough service, ] 30Volt bulbs are recommended.

B Insert the hooks at the bottom of the Iens into the slots

provided in the front plate of the power head (Figure MA-7).o Ftip Lens upand fasten with (2) #8-32 x 3/8"Phi]]ips Pan

Head Screwswhere indicated.

U_ith Opener. Any 1moth__pener to operate 1

mune_ stop_,orking. "

1 Button Compact Remote 3 Button Compact Remotew/Docking Station w/Docking Station

Figure MA-4 Genie Remote Controls

Figure MA-6

Receiver LearnCode Button

Receiver

(not toscab)

Figure MA-5 Learn Code Button and indicator Light

To program a Hemelink ®or CaJ'2U Device:(This GDO is Home!ink _ end Car2U compotible)

o Follow the Home[ink _)or Car2Uinstructions in your carowner's manual

JJ

Figure MA=7

For Help, call 1-8OO-35-GENIE or visit wwwogeniecompany,¢om

A Monthly:Door springs and door hardware:

Oil door roller, bearings, and hinges using siliconelubricant or light oil

DO not operatedooiautomaticai[y or manually if springs [are broken. Contact a Genie Factory Authorized Deater for

service orcaH Customer Service at 1.800.35.6ENIE. 1

, BaHanceDoor.

- CHosedoor.

- ReleaseCarriage Assembly from Rail Assembly by pullingthe Emergency Release Knob towards the door.

- Raise door manually 3L 4' and verify' that door stays atthat position. See Check Step 2 on page 4.

When the door is 3' _4' above the ground, the doorshould stay open. Slight movement is acceptable, ffthe door moves too much, contact a Genie FactoryAuthorized Dealer for service or call Customer Service at1-800=35-GENIE.

- Reattach CarnageAssemb[y to Rail Assembly:a. Pull the Emergency Release Knob toward Power Head.b. CHosedoor.

Contact Reverse Test.

- Perform Adjustment 2 on page 8.

WARNING:If the door fails to reverse on contact with the boardadjust the Close Force Control as specified in Set LimitSwitches and Force Controls on page 7 & 8. If the Openerstill fails, contact a Genie Factory Authorized Dealer forservice or call Customer Service at 1-800-35-GENIE

B Yearly:

Wipe off oid excess Hubdcant from Drive Screw.Lubricate Drive Screw with Genie Lubricant GLU-3_

UseONLYGenieLubricant (6LU-3). Other lubricantsmay damage the Opener.

GLU-3

Lubricant

FCC AND [C CERTIFIED

this device must accept any interference received, indudins interference that may cause undesired operation.

C As needed

Replace lightbulbs.(See page 9)

Safe-T-Beam ® System Self-Diagnostic Troubleshooting

Source {Red LED) Sensor {Green LED} Possible Problem solution

ON ON Normal operation None required

• Power Head not powered o Check breakers, fuses, plugsOFF OFF

• Wiring from Power Head bad • Check wiring for obvious shorts

OFF ON • Wiring to Source missing or bad • Check wiring• Power has been interrupted o Remove power and reappiy

2 BLINKS, Pause o Beam not aligned o Check Source, Sensor alignment

(Repeat) ON o Beam obstructed o Check for obstructiono Sensor defective o Contact Customer Service

2 BLINKS, Pause o Wire to Sensor missing or bad o Check wiring(Repeat) OFF o Sensor defective o Contact Customer Service

-3 BLINKS, Pause • Sensor receiving interference • Determine source of interference

(Repeat) ON o Check for interference from sun-

light or a source unit on an

adjacent door• Contact Customer Service

4 BLINKS, Pause o Source not sending pubes o Contact Customer ServiceON

(Repeat) • Source defective • Contact Customer Service

1 0 For Help, call 1-800-35-GENIE or visit www, geniecompanyocom

GeneraJ TroubJeshootingProbmem What To Do

Opener does not runfrom Wall Control

t

Door Opener startsfor no apparent reason

Door starts down, then

stops before it iscompletely closed

Door starts down, thenstops and goes back up

Door will only run dosed

m

Door will only run open

Lights will not turn off

Door starts up, but stop'.before it is

completely open

Operator runs,but doordoes not move

Wall ConsoleVacationLock function doesnot work

NoisyOperation

1. Check Lock switch on Wall Control (seeWall Console section on Installation Poster).2. Check Power Source:

* For Grounded Plug Connection.- Plug a lamp into the electrical outlet used for the door opener.

a. If lamp lights, power source is good.b. If lamp does not light, check fuse or circuit breaker.

* For Permanent Wiring Connection.- Check fuse or circuit breaker.

3. Check connections (seeWail Console section on Installation Poster):At Power Head Terminats and Walt Control.

1. Check Wires to ensure that they are not cut (Stapes can cut insutation and short Wires)Replace any shorting Staples and shorted Wires.

2. Was Remote Control lost or stolen? If so, erase all Remote Control codes from Receiver's memoryand reprogram for remaining remote controls. (See EraseAll Receiver Memory on page 11).

3. Ensurethat no Buttons are stuck"pushed-in"on Wall Console or any Remote Controls.

1. Check dose Limit Switch setting (page 7 and Installation Poster). Adjust as needed.2. Check Force Setting (page 7 & 8).Adjust as needed.3. Check for shorted wires.

1. If a new installation, check Door Arm position.2. Check operation of Contact Reversefunction.3. Check Safe-T-Beam¢_Systemfor beam obstruction or misalignment ofLenses.4. Check Safe-T-Beam_ Systemdiagnostic code.5. Check dose Forceadjustment (seeSetLimit Switchesand ForceControls on page 7 ). Adjust as needed.6. Check garagedoorfor binding.

1, Check Open Limit Switch for a short drcuit and for proper wiring,2, Check Open Force adjustment (seeSet Limit Switchesand ForceContro[s on page 7& 8). Adjust asneeded.:3, Check condition of garage door and door spring(s),4, WARNJNIG:If you suspect a probtem with the garage door hardware or springs, contact a Genie

Factory Authorized Dealer for service, or contact CustomerService at 1-800-3S-GENIE5. Check position of LockSwitch on Console.

1. Check Safe.T_Beam®SystemasdetaiIed in the Safe.T_Beam®System SeIf_diagn_sticTr_ubIesh__ting Chart

(page 10).2. Check d°se Limit Switch f°r a sh°rt circuit and f°r pr°per wiring'3. Check CIoseForceadjustment (seeSetLimit Switchesand ForceControls on page 7 & B). Adjust as needed.

m

1. DisconnectWires connecting WallConsole to Power Head(see"WalIConsole Installation"- on Installation poster).Check their condition and either replace or reconnect.

2. Until a replacement Wail Consolecan be obtained, disconnect Wall Consoleand useonly RemoteControlsor WirelessKeypadto operate Opener.

3. Check for non-compatible wall control.

1. Check (ensure) that garage door and Opener are in good repair, properly lubricated, and properlybalanced as detailed in Maintenance Section.

2, WARNING: If you suspect a problem with the garage door hardware or springs, contact a Genie FactoryAuthorized Dea_erfor service, or contact Customer Service at 1-800-35-GENIE,

3. Check Open Limit Switch for a short circuit and for proper wiring.4. Check Open Forceadjustment (see SetLimit Switchesand ForceControls on page 7 & 8). Adjust as needed.

T

1. EnsureCarriageAssembly isengaged to RailDrive Screw(seeInstallCarriage Assembly -INSTALLATIONPOSTER).2. Check Forceadjustment (seeSetLimit Switchesand ForceControls on page 7). Adjust asneeded.3. Check that alI sections of RailDrive Screware turning when Motor runs. If not:

Check condition (not cracked,split, or broken) and placement of Coupler. Replaceas needed.Check condition (not cracked,split, or broken) and placement of Collarand dip. Replacethemas needed.

1. EnsureCarriageAssembly is in contact with CloseLimit Switch.2. Check when door isfully closed,that Carriage activatesClose Limit Switch. If not.adjust position of Close

Limit Switch (Seepage7).

1. Besure all fastenersare tight.2. Check (ensure) that garage door and Opener are in good repair, properly lubricated, and properly

babnced as described in Maintenance Section (page 10).

11 For Help, call 1-800-35-GENIE or visit wwwogeniecompanyocom

WIRmNG DIAGRAM

[_ WA RN iNG,'_ M;ycauseE!ectrii%_Ck--_

CEoO

cc

2

THERMAL

PROTECTOR

BLACK

WHITE

GREEN /_

ORANGE

PRIMARYSEQUENCER

ORANGE

MOTOR

==

yELlOW

YELLOW

GREY

PRIMARY SECONDARY

.IGHTS

MOTORCAPACITOR

PURPLE

(Vet)

WALLCONTROL

STBSYSTEM

RADIOCONNECTOR........ u

TERMINALSTRIP

SEQUENCER/_

HOUSING

E

PARTS IDENTIFICATION

[1] ,o o, Assembly

Power Head Parts List

item Part Name

1 Power Head Assembly

A Cover (by Series Model)

B Front Plate Assembly

C Light Socket

D Motor Parts

E Receiver Assembly

F Capacitor(By Series/Model)

G Opto Wheel

H Opto-Luctor Assembly

J Sequencer Assembly

K Circuit Board Bracket

L Transformer

M Terminal StripN No.8-32 x 1/2" Hex Head Screw

w/Lockwasher

P No.8-32 x 3/8" Slot Hex Head

Screw w/Lockwasher

R Capacitor Isolator

4 1/4-20 Shoulder Bolt

5 1/4" Flange Nut

39 Coupler

41 No.8-32 x 3/8" Phillips

Hex Head Screw

42 No,8-32 x 3/8" Phillips

Pan Head Screw

48 Mounting Straps

49 Light Lens

1

1

1

1

2

1

1

1

1

1

4

1

1

1

1

1

2

2

1

4

2

2

1

For Help, call 1=800=3S-GENIE or visit wwwogeniecompany, com 1:2

PARTS [DENTmFmCATmON

[3] AssemUyii

Parts List (co.t')

item Part Name

1 Power Head Assembly (see page 12)

3 RailAssembly(3-piece)3A First Rail Section

3B Middle Rail Section

3C End Rail Section

4 1/4"-20 Hex Head Shoulder Bolt

5 1/4"-20 Hex Flange Nut

6 Carriage Stop

7 Rail Clamps

8 5/16"Hex Head Shoulder Bolt

9 5/16"Hex Flange Nut

10 Carriage Assembly11 Collar

12 Retaining Clip

13 Rail Strap

15 Limit Swit(h Assembly16 #8-32 x 3/8" Hex Head Screw

17 Emergency Release Cord

18 Emergency Release Knob

19 Emergency ReleaseTag (not shown)20 Header Bracket

21 Door Bracket

22 1/4"x2"LagScrew

23 Straight Door Arm24 Clevis Pin

25 Cotter Pin

26 Curved Door Arm

27 3/8"x 7/8"Hex Head Bolt

28 3/8" Hex Flange Nut

Numbermnduded

1

1

1

1

1

2

2

1

4

8

13

1

2

2

1

2

2

1

1

1

1

1

7

1

2

2

1

2

2

Parts List (cont9

29

30

31

33

35

36

37

_gsft

30

varies

varies

1

Part Name

Wire (not shown)

Insulated Staples (not shown)

Wall Button (not shown)

Wall Console (not shown)

Entrapment WARNING Label (not shown)

Safe-T-Beam (STB)Sensor (green LED)

(not shown

Safe-T-Beam Source (red LED)

(not shown)

Safe-T-Beam Bracket (not shown)

Coupler

#10 x 1q/4" Phillips Hex Head Screw

Safety and Maintenance Guide

(not shown)

Wire Clip5/16" x 3/4"Hex Head Bolt

1/4"-20 x 3/4" Self-tapping Screw

Mounting Straps

Light Lens (see page 12)

Remote Control (not shown)

I

2

I

4

38

39

40

43

1

44 4

46 5

47 3

48 2

49 1

50 varies

For HeJp, ca[[ 1-800-3S-GENIE or visit wwwogeniecompany, com 13

Garage Door Opener Accessories Order FormFormu[ario de pedido de accesorios pare abndores de puertas de garajeFormulaire de commando des accessoires pour ouvre-porte de garageForadditionalaccessoriesnotshown.visitourwebsiteat www.geniecompany.comPareaccesodosadicionalesnomostrada,visitenuestrositioweben www.geniecompany.compourlosaccessoiressupplBmentairespasmontrB,visiternotrBsiteweb_ www.geniecompany.com

(GI CT390-1 ) 1°Button compact Remote- Allowsremote operationof garagedoor.

Cempdmad Monde do Dgtanda- ProporciBnaroperation remotede la pumtade[ garaje.

TBIOcommandocempacto- Pemmttreop&ation _loign-de porte degarage. P/N 36248R $36.50

(G[FT390-1) 1=ButtonRashlight Transmitter - RemoteControllerwith aFlashlight.1abrocha transmgor do lintorna- Directorremotecon una[intema.

l=boutonnor FOmottourdo lampodo pocho - LecontrOMlr doign_ avecde lampede poche.

P/N 35657S $45.00

(G[ C[390-3) 3=ButtonCompact Remote- Allowsremoteoperation of 3garagedoors.

Do3 botonos Comprimad Monde do Distancia- PropordOnaroperation remotede tres[aspuertasdd garaje.3°beutonnor laTOIOcommandocompacto - Pennettreop@ation_loign' trois portes@garage. P/N 36223R $50.00

(GWC-2W} Dduxo Wall Consdo - OperatesGarageDoor.Independentlight control.Securityvacationlock.¢onsda do [ujo do pared - Acciona[apuerta dd garaje,Controlde [uzindependiente.Cerraduradeseguridadparavacadones.La¢onsdo dso [uxodo Mur- Acfionne laporte de garage.Commanded'_dairageind@endante.

Intermpteurde verrouilhgede s_curRO. P/N 35661 R $35.00

(GWKPD} wirdoss Keypad- Operates[ntdlicode"GarageDoor Openerswithout RemoteControlorkey.Sistomado ontrada per todado numOricoinal_mbrico- AccionaInsabridomsde puertasde garajeIntellicode sincontrol remoteo Ilave.

SystOmod'ouvro-porto dogarage _ davior sansfib Actinnnelosouvre-pnrtede garageavecIntellicode sanstd_commande ni cir.

P/N 35691R $50.00

(GLU-3} 314oz, ScrewDdvo Lubricant - Ensuresproperequipment wear protection.

3/4once Lubricanto do tornillo occionar - Asegmacomponentecorrectoprotection per deterioro.

Laonza 3/4Lubrkant do la vis - Garantlrcomponentexactparsyst_meddenseversuser. P/N 35218A. S $5.00

(6W-2) Universal Wall Button- Providesadditionalconvenientinsideoperation of does _>1

BotBndo pared universal- Propordonaoperad6n convenientede [apuerto des@el interior.

neuron mural universe[- ActionneFnuvm-portedeI'int@ieurdu garage. P/N 35693R $3.75

(GPS-5} Perfect Step- Ensuresperfectparking. ZZE_....... _-

StopPorfoctd- Asegurael estacionamientoperfecto.

Butoir Perfect Step'- Permetde stationnmala perfectiondanelegarage. P/N 35677R $4.00

(GABXS} Bolt Drive E×tonsionKit- AnExtenBonthat increasesthe travelof an Openerto accommodatean

eight foot door.

Juogo do oxtonsi6n do cadonadoslizabla- Unaextensionparaaumentarla Iongitudde labarandade ChainGlide,paraacomodarunapuertade 8pies(2,43m),

N&ossairo do prolongomont du couikseau - Rallongede prdongeanth coursedeI'ouvre-porteChainGlidepourune porte de2,4m (gpi)de hauteur. P/N 35663R $32.00

(LCBX-8} chain Ddvo ExtensionKit- An Extensionthat increasesthe travelof anOpenerto accommodatean _

eight foot door. _ )

Juogo do oxtonsi6n de cadonadoslizablo- Unaextensionparaaumentar laIongitudde h barandadeChain _._/Glide,paraacomodarunapuerta de8pies(2,43m).

N&ossaira de prolongamant du coulksoau - Raliongede prdongeant [a coursede ['ouvre-pmteChainGlidepour uneporte de2,4m (8pi)de hauteur. P/N 35679 R $32.00

(GSX-8} ScrewDrive Extension Kit- AnExtensionto increasetravelof anOperatorto accommodate

eight foot door.

Juago do extension doslizanto do ScrewDdvo- Bnaextensionpare aumentar [acarfarede un abridor _,desiizaNe,paraacomodaruna puerta de 8pies (2,43m.).

N&essaire de raliongodu ScrewDrive- Rallongede prolongeant la

course@I'ouvre-portepour une portede 2,4m (8pi) de hauteur.(GIRUqT) P/N 35678R $32.00

(60WATT)Enhancad/BoughServiceLight Bulb- Ensuresproperequipment compatabilW /%Bembilla do60 Vatios- Aseguracomponentecorrectode sBtema. _--_"

Edairago de 60 WATT-Garantircomponentexactparsysteme. P/N 26210A.S $2.73

(GER-2} Emergenoy Release }(it - Provides access to garage from outside in the event ofan electrical power failure.

Juego de pica-porte de pastille - Permitir entrtada desde par fuera de garaje porque cortede el&trim.

NBcossairee de D_dencbement de seceuro - Le n&essaire de d&lenchement

de secours est consupour vous perme_tre d'accOder Rvotre garage depuisI'extBrieur en cos de panne de courant et Iorsqu% P/N 35675R $20.00

STB Adapter Brackets (2) - Used in conjunction with standard STBBrackets.They provide

additional clearance and mounting options.

EI adaptador pone entre par_ntesis (2) - Usado en uni6n con par_ntesis uniformes demontar de STB,ellos proporcionan el espacio libre adicional junto con mortar las opdones.

Croohets d'adaptateur (2} - UtilisB conjointement avec STBstandard mentor les crochets,

ils fournissent le dBgagement supplementaire avec mentor d'options. P/N 34439R.S $4.37

How many?LQu_ntos_

Ordering InstructionsNo C.O.D.shipments. Please include check or money order,made payable to The Genie Company. Do not send cash.Allow 34 weeks for delivery.1-800-3544643. Please have part number and credit cardready. Mail Order Form to: Genie Company, 22790 LakePark Blvd, Alliance, Ohio 44601 .We accept Visa orMastercard on phone orders only.

Pleaseadd local salestax if you leUde in one of the states listed

California, Connecticut, Florida, Georgia, Illinois, Indiana, Maryland,Massachusett_ Michigan, New Jersey, New York, Ohio, Tennessee,

Virginia, Wisconsin

TOTALORDER

SHIPPING& HANDLING

STATESALESFAX

GRAND TO]:AL

S

S 5.o0

S

S

Las Instrucciones que OrdenanNo se aceptan pedidos de page centre entrega (COD).Sirvase incJuir su cheque o sire postal, Jacuenta pagaderahecha aThe Genie Company. No env[e dinero en elective.ConcBdanos 3 a 4 semanas para[a entrega. 1-800-35&3643.Sirvase tenor [istos los nOmeros de[ mode[o y de [a tadeta decr_dito. Enviar hater un pedido de mercancia a: GenieCompany, 22790 Lake Park Bird, Alliance, Ohio44601Aceptamos pedidos telefBnicos de Visa o Mastercard.Silvase aglegal el impue to de venta local si usted reside en uno de los

Uguientes estados;

California, Connecticut, Florida, Georgia, Illinois, Indiana, Maryland,

Massachusetts, Michigan, New Jersey, New Yolk, Ohio, Tennessee,

VOginia,Wisconsin

TOEAL DEL PEDIDO $

FLETEYMANEJO $ 5.00

IMPUESTODEVENTAS ES-FATAL $

GRANTOTAL $

Instructions CommandantPasd'exp_dition centre remboursemencVeuillez indure un ch#queou un mandat bancake,le payablefait aTheGenie Company,N'envoyezpasd'argent comptam.Accordezde 3_4 semainespourla [ivraison.1-800-354 3643,Ayezsous[amain [e num&o de [a pieceet celuide [acarte de cr_dicMettre _[a poste learmgement a:GenieCompan_ 22790LakeParkBlvd,Alliance,Ohio 4400I.Nousacceptons loscommandospar t_l@hone avecpaiement par cartedecredit Visaou Mastercard.

VeuiIlez indJquel los taxes de vente locales si vous i _sklez clans I'un des _,tats

repertories ci dessous

California, Connecticut, Florida, Geomia, Illinois, Indiana, Mawland,

Massachusetts, Michigan, New Jersey, New Yell<,Ohio, ]%nnessee,Vagirda,Wiscon in

COMMANDE TOTALE $

MANUTENTION ET EXPEDITION $ 5.00

-EAXE DE VENTE $

TOTAL GLOBAL $

SHIP ORDERTO:

ENVIAR MEfiCANCIA CON:

EXPEDIERMARCHANDISE POUR:

NAME/ NOMBflE/ NOM

ADDRESS/ DIRECCION/ ADfiESSE

CITY/ CIUDAD/ WLLE

STArE/ EflTADO/ ETAT

ZiP / ( ODIGO POSTAL / CODE POSTAL

(Prices subject to change without notice)

(Valoran el cambio con sujeci6n a sin nora)

(Lee prix assujettissent pour changer sans [a notification)

For Help, call 1-800-35-GENIE or visit www.geniecompany.com