removal of basic dyes from aqueous solutions using mustard … · 2017-12-12 · 3.1.2 energy...
TRANSCRIPT
INTERNATIONAL JOURNAL OF ENVIRONMENTAL SCIENCES Volume 3, No 5, 2013
© Copyright by the authors - Licensee IPA- Under Creative Commons license 3.0
Research article ISSN 0976 – 4402
Received on January 2013 Published on April 2013 1711
Removal of basic dyes from aqueous solutions using mustard waste ash and
buffalo dung ash Harminder Singh, Samiksha, Sameena Roohi
Department of Chemistry, Lovely Professional University, Punjab 144402, India
doi: 10.6088/ijes.2013030500039
ABSTRACT
The ability of the low cost materials viz. mustard waste ash (MWA) and buffalo dung ash
(BDA) to remove two basic dyes, Methylene Blue (MB) and Crystal Violet (CV) in aqueous
solution, was studied by the method of batch mode adsorption process. Effect of contact time,
initial dye concentration (mg/L), adsorbent dosage (g/L) and pH was studied and results
showed that amount of the dye adsorbed increase with increase in all the parameters studied.
Data was fitted to Langmuir and Freundlich models and it showed that the both isotherm
fitted well to the adsorption data. The Langmuir adsorption capacity of the MWA was 245.76
mg/g and 1079 mg/g respectively for MB and CV whereas this value for BDA was found to
be 294.11 and 1063.38 for MB and CV respectively. Apart from this, adsorbents were
characterized by Electron Dispersion X-ray Spectroscopy (EDS) and Scanning Electron
Microscopy (SEM).
Keywords: Biowastes, buffalo dung, crystal violet, methylene blue, mustard waste, sorption.
1. Introduction
Pollution caused by textile industry is the major concern for the developing countries.
Considering both volume-discharged and effluent combustion, the wastewater from the
textile industry is rated as the most polluting among all industrial sectors. Dyes present even
in low concentrations are highly visible. They affect the photosynthetic activity of the aquatic
life due to the reduced light penetration. Hence, dyes disturbing biological process of the
aquatic life especially the photosynthesis activity (Gücek et al. 2005). Dyes may be
carcinogenic, mutagenic, or teratogenic. Additionally it may also cause severe damage to
human beings such as dysfunction of kidney, reproductive system, liver brain and central
nervous system. The dyes are generally resistant to environmental conditions like light, effect
of pH and microbial attack. The removal of dyes from industrial effluents in an economical
way is a growing concern these days. There are various methods for the removal of dyes
including sedimentation and flotation, membrane separation, coagulation and ion exchange.
The cost of operation is the main drawback of these techniques (Garg et al. 2003).
The adsorption process is an efficient method for the removal of dyes from the waste
effluents. It is preferred over other techniques due to its less initial cost, flexibility and
simplicity of design, ease of operation and insensitivity to toxic pollutants. Activated carbon
adsorption is one of the widely used techniques but because of the high cost and regeneration
problems, there has been a constant search and demand for potential low cost adsorbents. A
number of low-cost adsorbents such as neem leaves (Velmurugan et al. 2011), sphagnum
moss peat (Luisa et al. 2008), treated guava seeds (Joseph et al. 2007), gypsum (Rauf and
Bukallah 2009), palm kernal coat (Gimba et al. 2011), tamarind fruit shell powder and
Removal of Basic Dyes from Aqueous Solutions Using Mustard Waste Ash and Buffalo Dung Ash
Harminder Singh et al
International Journal of Environmental Sciences Volume 3 No.5, 2013 1712
almond tree bark powder (Patil et al. 2011), cucumber peel (Thirumalisamy and Subbain 2010),
waste sludge from biodiesel plant (Gottipati and Mishra 2010) have been employed for the
removal of basic dyes via adsorption. In the present study, the potential of two low cost bio-
sorbents, viz. buffalo dung ash (BDA), mustard waste ash (MWA) for the removal of
methylene blue and crystal violet from the aqueous solution is studied.
2. Materials and methods
2.1 Adsorbent preparation
The adsorbents used in this study are BDA and MWA, waste materials and abundantely
available in rural areas of India.
BDA: Buffalo dung cakes were collected from Rama Mandi, a town near Jalandhar (India)
and the cakes were burnt in Muffle furnace at a temperature of 500˚ C for three hours and
stored in air tight container for further use.
MWA: Mustard waste was collected from Jalandhar (India) and was burnt in muffle furnace
at 500˚ C for three hours and stored in air tight container for further use. Both the adsorbents
were sieved through an I.S.70 mesh screen (70 µm) prior to their use.
2.2 Surface characterisation
Surface morphology and chemical constitution of both the adsorbents were studied by
Scanning Electron Microscopy (SEM) (model: FEI Quanta 450 FEG) and Energy dispersive
X-ray spectroscopy (EDS).
2.3 Adsorption studies
A stock solution of both Methylene blue (MB) and Crystal violet (CV) were prepared by
dissolving 1 g of the respective dye in 1 L of the double distilled water (1000 mg/L)
separately. This solution was further used to make desired concentrations using double
distilled water. The pH adjustments were made using hydrochloric acid and sodium
hydroxide. Batch mode experimental studies were carried out with a known weight of the
adsorbent in 50 mL working solution of different concentration range (100-800 mg/L) in 100
mL conical flask with stoppers. Although this concentration range is much higher than the
dyes would be in most effluents, but high concentrations helped in minimizing the error in the
estimation of dyes spectrophotometrically. These flasks were kept in a thermostatic shaker
maintained at a temperature of 30oC and 200 rpm for sufficient time to achieve equilibrium.
After equilibration, the adsorbent was separated by filtration using Whatman’s paper no. 40
and the aqueous phase concentration of the dyes was analyzed using UV-VIS
spectrophotometer (Shimadzu-1800) by observing optical density at different wavelengths for
MB and CV respectively at 662 and 591 nm. The above mentioned process repeated to find
the effect of different adsorption parameters like adsorbent dose (0.1-0.5 g/50mL), pH (2-9),
contact time etc. by keeping all other parameters at a fixed value.
2.4 Adsorption isotherms
Removal of Basic Dyes from Aqueous Solutions Using Mustard Waste Ash and Buffalo Dung Ash
Harminder Singh et al
International Journal of Environmental Sciences Volume 3 No.5, 2013 1713
The adsorption isotherm is relatively simple method for determining the feasibility of using
an adsorbent for a particular application. It is a plot of the amount of adsorbate adsorbed per
unit weight of adsorbent (Qe) versus the equilibrium concentration of adsorbate (Ce).
The sorption equilibrium (Qe) uptake capacity in mg/g, for each sample is calculated
according to mass balance and is expressed as
Q e = Vm
CC eo
Where Co and Ce are initial and equilibrium concentrations of dyes respectively, m is the
mass of adsorbent and V is the volume of solution in litres (Krishnaiah et al. 2006).
Adsorption isotherms on different adsorbents are usually presented as Langmuir and
Freundlich isotherms. The former shows initial rapid adsorption tending to be almost constant
at higher concentrations.
The linear form of the Langmuir isotherm is represented as:
CebQQQe
1111
The plots of eQ
1and
Ce
1for both the dyes were drawn for the data obtained in this study.
From the slope and intercept, the values of constants Q and b can be calculated. Where Q
signifies the adsorption capacity (mg/g) and b signifies the energy of adsorption (L/mg).
An important characteristic of the Langmuir adsorption is expressed in terms of a
dimensionless separation factor RL (Namasivayam et al. 2001) and is defined as
RL = obC1
1
Where Co is the highest initial dye concentration (mg/L) and b is the Langmuir constant. This
parameter indicates the isotherm shape according to the adsorption characteristics:
RL > 1, the process is unfavourable
RL = 1, the process corresponds to linear
0 < RL > 1, Process is favourable
RL = 0, Irreversible process
The linearized Freundlich isotherm is given by
Log eQ = Log KF + n
1log Ce
Values of Log eQ and Log Ce were plotted for both the dyes separately. From the intercept
and slope the values of Freundlich constants KF and n can be calculated. The KF represents
adsorption capacity and n refers to the process intensity (Gupta and Ali 2000). This isotherm
is frequently used for the interpretation of adsorption from solutions because of its simplicity.
Generally, straight-line plots can be obtained by making use of the empirical Freundlich
equation.
3. Results and discussion
3.1 Characterization of adsorbents
3.1.1 Scanning electron microscopy
Removal of Basic Dyes from Aqueous Solutions Using Mustard Waste Ash and Buffalo Dung Ash
Harminder Singh et al
International Journal of Environmental Sciences Volume 3 No.5, 2013 1714
Surface morphology of adsorbents was analysed by scanning electron microscopy which
showed a clear view of the grains of the materials used as adsorbent in this study. Scanning
electron micrograph of MWA and BDA are shown in Fig. 1 a & b respectively. It is clear
from Fig. 1a that MWA has a rough and uneven surface having small pores which have
diameter in the range from 0.182 µm to 3.5µm. These pores can serve as adsorption sites for
the removal of dyes. On the other hand BDA has fibrous structure and having small pellet
which are distributed throughout and the size of these fibres varies from 1.66 µm to 52 µm.
Space between these fibres and pellets may serve as adsorption sites.
Figure 1 ((a), (b)): Scanning electron micrographs of MWA and BDA respectively
3.1.2 Energy dispersive X-ray spectroscopy (EDS)
The chemical constitution of both the adsorbents was studied by EDS. EDS spectra is shown
in figures 2 (a and b) for MWA and BDA respectively and elemental constitution is
represented in Table 1. It can be observed that carbon content was found to be more in MWA
(75.93) than BDA (55.57). Both the adsorbent have very different elemental constitution.
Removal of Basic Dyes from Aqueous Solutions Using Mustard Waste Ash and Buffalo Dung Ash
Harminder Singh et al
International Journal of Environmental Sciences Volume 3 No.5, 2013 1715
1 2 3 4 5 6 7 8 9
keV
0
2
4
6
8
10
12
14
16
18
cps/eV
C O K K
Ca
Ca
Mg Ir Ir Ir
Ir
S
S
1 2 3 4 5 6 7 8 9
keV
0
2
4
6
8
10
12
14
16
cps/eV
C O Si K K
Ca Ca
Cl
Cl
Mg
N Na
Figure 2 ((a), (b)): EDS Spectra of MWA and BDA respectively
Table 1: Characterization of MWA & BDA using EDS
S.No. Element
MWA BDA
Atomic
composition
(at. %)
Error
(wt. %)
Atomic
composition
(at. %)
Error
(wt. %)
1 C 75.93 8.7 55.57 4.4
2 O 22.01 4.2 15.70 1.2
3 K 0.47 0.1 4.02 0.3
4 Ca 0.36 0.1 1.22 0.1
5 Mg 0.20 0.1 1.03 0.1
6 S 0.85 0.1 - -
7 Ir 22.01 4.2 - -
8 Si - - 18.97 0.9
9 Cl - - 1.23 0.1
10 Na - - 0.95 0.1
11 N - - 1.30 0.2
3.2 Effect of contact time
For the evaluation of adsorption as a function of time, amount of dye adsorbed per gram (Qe)
and the percentage removal was calculated at regular intervals of 10 minutes until
equilibrium was achieved. The first phase was interpreted to be the instantaneous adsorption
Removal of Basic Dyes from Aqueous Solutions Using Mustard Waste Ash and Buffalo Dung Ash
Harminder Singh et al
International Journal of Environmental Sciences Volume 3 No.5, 2013 1716
stage or external surface adsorption. The plots of adsorption percentage versus time (Figure
3a and b) indicate that the adsorption become asymptotic to the time axis representing nearly
an equilibrium pattern. The equilibrium time for MB using both the adsorbents was found to
be 150 minutes whereas for CV it was 120 minutes and 140 minutes with BDA and MWA
respectively. For the further batch studies the equilibrium time was set to be three hours for
both the dyes.
Figure 3 ((a), (b)): Effect of contact time on the adsorption process for MB and CV
respectively. (Temperature = 30o ±1, adsorbent dose= 0.1g/mL, rotations per minute=200±1,
Concentration of dyes= 600 mg/L, pH=6.0 for MB and pH=6.5 for CV)
3.3 Effect of pH
pH is one of the most important factors in controlling the adsorption process. To evaluate the
effect of pH on the adsorption process, the adsorption of the dyes with pH values from 2-9
were studied keeping all other variables constant. It was observed after analyzing Fig. 4a & b
for methylene blue and crystal violet respectively that the amount of dye adsorbed per unit
weight of adsorbent (Qe) increased with increasing pH values. As the pH of the solution
increases, the surface charge density decreases and the electrostatic repulsions between the
adsorbent and the positively charged basic dyes is less, thereby increasing the extent of
adsorption. Similar results have been reported elsewhere (Patel and Vashi 2010).
Removal of Basic Dyes from Aqueous Solutions Using Mustard Waste Ash and Buffalo Dung Ash
Harminder Singh et al
International Journal of Environmental Sciences Volume 3 No.5, 2013 1717
Figure 4 ((a), (b)): Effect of pH on the amount of dyes adsorbed per unit weight (Qe) for the
two adsorbents for MB and CV respectively. (Temperature = 30o ±1, adsorbent dose=
0.1g/mL, rotations per minute=200±1, Concentration of dyes= 600 mg/L, equilibrium time =
3hrs).
3.4 Effect of adsorbent dose
The effect of adsorbent dose was studied by varying the amount of adsorbent dose from 0.1g
to 0.5g in 50 mL solution of both the dyes having 600 mg/L of initial concentration keeping
all other parameters at a constant value. The results are shown in figures 5a & b for the dyes
methylene blue and crystal violet respectively.
Removal of Basic Dyes from Aqueous Solutions Using Mustard Waste Ash and Buffalo Dung Ash
Harminder Singh et al
International Journal of Environmental Sciences Volume 3 No.5, 2013 1718
Figure 5 (a and b): Effect of adsorbent dose on the amount of dyes adsorbed per unit weight
(Qe) and % removal of dyes for the two adsorbents for MB and CV respectively.
(Temperature = 30o ±1, rotations per minute=200±1, Concentration of dyes= 600 mg/L,
equilibrium time = 3hrs pH=6.0 for MB and pH=6.5 for CV).
From obtained data it was observed that with increasing amount of adsorbent, percentage
adsorption also increases accordingly because maximum surface area is available for
adsorption which increases exchangeable number of sites on the surface of the adsorbent.
However, a decrease in the value of Qe was observed from 274.5 mg/g to 66.3 mg/g,
247.6mg/g to 58mg/g with BDA for MB and CV respectively and on the other side the
decrease was from 182 mg/g to 52.88 mg/g, 239.5 mg/g to 54 mg/g in the value of Qe when
MWA is used with MB and CV respectively. The decrease in the amount of dye adsorbed per
gram of the adsorbents (Qe) with increase in the adsorbent dose is mainly because of
unsaturation of adsorption sites through the adsorption process (Kovacevic et al. 2000).
3.5 Effect of initial concentration of adsorbate
The amount of dyes adsorbed per gram of the two adsorbents used in this study was observed
at different dye concentrations (100 – 800 mg/L). The result showed that the amount of dye
adsorbed per gram of adsorbent (Qe) increased and percentage removal of the dye decreased
(Fig 6a & b). It was observed that with the increase in concentration of adsorbate, percentage
removal decreases, as after some concentration there is less number of adsorbing sites
available for the dye adsorption on the surface of adsorbent. The reason is that during the
adsorption of dye initially the dye molecules rapidly reached the boundary layer by mass
transfer and then they slowly diffuse from boundary layer onto the adsorbent because many
of the available sites have been occupied, and they finally diffuse into the porous structure of
the adsorbent. On the other hand the value of Qe was observed to be increased from 48.63
mg/g to 344.9 mg/g, and 39.9 mg/g to 302.4 mg/g respectively for MB and CV using BDA.
For MWA value of Qe increased from 42.9 mg/g to 250.3 mg/g for MB and it increased from
37.2 mg/g to 286.9 mg/g for CV. When initial concentration of the dye is increased, it
contributes to the driving force to overcome mass transfer resistance of ions between the
adsorbent and bulk fluid phases thereby increasing the uptake of dye molecules. Not only this,
increase in the concentration of dyes also increases number of collisions between adsorbate
and the adsorbent which results in increase of the adsorption (Krishnaiah et al. 2006).
Removal of Basic Dyes from Aqueous Solutions Using Mustard Waste Ash and Buffalo Dung Ash
Harminder Singh et al
International Journal of Environmental Sciences Volume 3 No.5, 2013 1719
Figure 6 (a and b): Effect of initial dye concentration on the amount of dyes adsorbed per
unit weight (Qe) and % removal of dyes for the two adsorbents for MB and CV respectively.
(Temperature = 30o ±1, rotations per minute=200±1, adsorbent dose= 0.1g/mL, equilibrium
time = 3hrs pH=6.0 for MB and pH=6.5 for CV).
3.6 Adsorption isotherm
The adsorption data are usually described analyzed and modeled using an adsorption
isotherm. It relates the amount of dye adsorbed per unit weight of the adsorbent to the
equilibrium concentration of the bulk phase. Data obtained in the study was fitted to the
Langmuir (Figure 7a & b) and Freundlich models (Figure 8a & b) which are often used to
describe equilibrium adsorption isotherms. The results obtained from Langmuir and
Freundlich isotherms indicate the strong adsorption capacity of adsorbents for the dyes.
Adsorption constant for Langmuir isotherm (b and Q) and Freundlich isotherm (KF and n)
were calculated from slope and intercept and are given in Table 2 for both the dyes. Data
fitted very well to both the isotherm as indicated by the ‘R’ values in table 2. A special
parameter ‘RL’ was also calculated for the two adsorbents used in this study on both the dyes.
Removal of Basic Dyes from Aqueous Solutions Using Mustard Waste Ash and Buffalo Dung Ash
Harminder Singh et al
International Journal of Environmental Sciences Volume 3 No.5, 2013 1720
Figure 7 (a and b): Langmuir adsorption isotherm for the two adsorbents for MB and CV
respectively. (Temperature = 30o ±1, rotations per minute=200±1, adsorbent dose= 0.1g/mL,
equilibrium time = 3hrs pH=6.0 for MB and pH=6.5 for CV).
Figure 8 ((a), (b)): Freundlich adsorption isotherm for the two adsorbents for MB and CV
respectively. (Temperature = 30o ±1, rotations per minute=200±1, adsorbent dose= 0.1g/mL,
equilibrium time = 3hrs pH=6.0 for MB and pH=6.5 for CV). Table 2: Langmuir and
Freundlich constants
Langmuir and Freundlich constants for MB
Langmuir constants Freundlich constants
Parameter MWA BDA Parameter MWA BDA
Q (mg/g) 248.756 294.11 KF 9.537 28.8071
b (L/mg) 0.0142 0.0696 n 1.741 1.826
R 0.9906 0.980 R 0.9985 0.9916
SD 9.53 x 10-4
0.0013
SD 0.0148 0.0404
RL 0.081 0.0176 - - -
Langmuir and Freundlich constants for CV
Removal of Basic Dyes from Aqueous Solutions Using Mustard Waste Ash and Buffalo Dung Ash
Harminder Singh et al
International Journal of Environmental Sciences Volume 3 No.5, 2013 1721
Parameter MWA BDA Parameter MWA BDA
Q (mg/g) 1079.252 1063.382 KF (mg/g) 3.7480 2.083
b (L/mg) 0.001594 0.00188 n 1.2709 1.0421
R
0.95619 0.9846 R
0.967 0.986
SD 0.00244 0.0014 SD 0.0789 0.053
RL 0.44 0.6614 - - -
Its value for methylene blue was found to be 0.081 and 0.0176 for MWA and BDA
respectively whereas for crystal violet it was found to be 0.44 and 0.6614 respectively for
MWA and BDA. It is clear from these values that ‘RL’ is between 0 and 1, which indicates
that the adsorption process for these adsorbents was favourable. Table 3 a and b represents
adsorption capacities of various low cost adsorbents used for methylene blue and crystal
violet and it can be clearly observed that adsorbents used in this study have adsorption
capacities with the low cost absorbents reported in the literature. More over both these
adsorbents even outperformed in case of crystal violet dye adsorption.
Table 3 (a): Adsorption capacity of various adsorbents with MB
Adsorbent Name Qe (mg/g)
Sawdust (Ansari and Mosayebzadeh 2010)
19.41
Sawdust coated with polypyrole (Ansari and Mosayebzadeh 2010)
34.36
Gypsum (Rauf et al. 2009) 36
Palygorskite (Al-Futaisi et al. 2007) 50.8
Yellow Passion Fruit waste (Pavan et al. 2008) 44.7
Coffee hysks (Oliveira et al. 2008) 90
Waste from biodiesel plant (Gottipati and Mishra 2010) 40
Sargassum (Tahir et al. 2008)
145.55
Cucumber peel (Thirumalisamy and Subbaine, 2010) 46.73
Ulva lactuca (Tahir et al. 2008)
69.23
Rectorite (He et al. 2010) 81.2
Carbon prepared from Guava seeds (Joseph et al. 2007) 198.12
Ghassoul (Natural clay) (Elass et al. 2010) 290
MWA 248.756
Removal of Basic Dyes from Aqueous Solutions Using Mustard Waste Ash and Buffalo Dung Ash
Harminder Singh et al
International Journal of Environmental Sciences Volume 3 No.5, 2013 1722
BDA 294.11
Table 3 (b): Adsorption capacity of various adsorbents with CV
Adsorbent Name Qe (mg/g)
Jute fibre carbon (Porkodi and Vasanthkumar 2007) 27.99
Tamarind fruit shell powder (Patil et al. 2011) 142.85
Almond tree bark powder (Patil et al. 2011) 166.66
Mango leaf powder (Patil et al. 2011) 200
Mangrove plant leaf powder (Patil et al. 2011) 200
Teak tree bark powder (Patil et al. 2011) 200
Mangrove plant fruit powder (Patil et al. 2011) 250
carbon from Ricinus communis pericarp (Madhavakrishanan et al.
2009) 106.95
Activated carbon from sewage sludge(Graham et al. 2001) 68.13249
Activated carbon from coconut husk(Graham et al. 2001) 61.60483
Unexpanded perlite(Dogan and Alkan 2003) 3.30463
Expanded perlite(Dogan and Alkan 200 3) 1.142341
Bagasse fly ash(Mall et al. 2006) 26.23305
Activated carbon (PAAC)(Senthilkumaar et al. 2006) 60.74807
MCM-22(Wang et al. 2006) 48.95748
Palygorskite(Al-Futaisi et al. 2007) 57.93302
Raw sepiolite(Eren and Afsin 2007) 73.43622
Raw kaolin(Nandi et al. 2008 ) 44.87769
UNCAL BC(Monash et al. 2011) 48.95748
CAL BC(Monash et al. 2011) 40.49
BDA 1063.382
MWA 1079.252
4. Conclusion
Adsorption of two basic dyes methylene blue and crystal violet was investigated using two
low cost biowaste adsorbents, viz. MWA & BDA. Conclusion from this study can be
represented as follows
1. Surface morphology and surface particles size of the two adsorbents used in this study
were quite different from each other MWA has uneven surface with small pores
whereas BDA has fibrous character.
2. It was also concluded that pH of the solution has a marked effect on the adsorption
and adsorption increased with the increase in pH value.
Removal of Basic Dyes from Aqueous Solutions Using Mustard Waste Ash and Buffalo Dung Ash
Harminder Singh et al
International Journal of Environmental Sciences Volume 3 No.5, 2013 1723
3. It was found that adsorbent dose and initial concentration of dyes has a significant
effect on the adsorption of dyes.
4. Both Langmuir and Freundlich adsorption isotherm fitted well for the adsorbent.
Adsorption capacities were found to be 248.76 and 294.11 for MWA and BDA
respectively for methylene blue where as for crystal violet these values were found to
be 1079.25 and 1063.38 for MWA and BDA respectively.
5. It was also found that adsorption capacity of MWA & BDA were comparable to many
other low cost adsorbents reported in the literature. Therefore it can be concluded that
MWA and BDA can be used as adsorbents for the removal of cationic dyes.
5. References
1. Al-Futaisi, A., Jamrah, A. and Al-Hanai, R, (2007), Aspects of cationic dye molecule
adsorption to palygorskite, Desalination, 214, pp 327-342.
2. Ansari, R. and Mosayebzadeh, Z, (2010), Removal of Basic Dye Methylene Blue
from Aqueous Solutions Using Sawdust and Sawdust Coated with Polypyrrole,
Journal of the Iranian Chemical Society, 7(2), pp 339-350.
3. Dogan, M. and Alkan, M, 2003, Removal of methyl violet from aqueous solution by
perlite, Journal of Colloid Interface Science, 267, pp 32–41.
4. Elass, K., Laachach, A., Alaoui, A. and Azzi, M, 2010, Removal of methylene blue
from aqueous solution using ghassoul, a low-cost adsorbent, Applied ecology and
Enviromental Research, 8, pp 153-163.
5. Eren, E. and Afsin, B, 2007, Investigation of a basic dye adsorption from aqueous
solution onto raw and pre-treated sepiolite surfaces. Dyes Pigments, 73(2), pp 162–
167.
6. Garg, V.K., Gupta, R., Yadav,A. and Kumar, R. 2003 Dye removal from aqueous
solution by adsorption on treated sawdust. Bioresource Technology, 89(2), pp 121-
124.
7. Gimba, C.E., Abechi, E.S., Uzairu, A. and Kagbu, J.A. 2011, Kinetics of adsorption
of methylene blue onto activated carbon prepared from palm kernel shell. Archives of
Applied Science Research, 3 (1), pp 154-164.
8. Gottipati, R. and Mishra, S, 2010, Application of biowaste (waste generated in
biodiesel plant) as an adsorbent for the removal of hazardous bye - methylene blue -
from aqueous phase. Braz. J. Chem. Eng., 27(2), pp 357-367.
9. Graham, N., Chen, X.G. and Jayaseelan, S, 2001, The potential application of
activated carbon from sewage sludge to organic dyes removal. Water Sci Technol., 43,
pp 245–252.
Removal of Basic Dyes from Aqueous Solutions Using Mustard Waste Ash and Buffalo Dung Ash
Harminder Singh et al
International Journal of Environmental Sciences Volume 3 No.5, 2013 1724
10. Gücek, A., Sener, S., Bilgen, S. and Mazmancı, M.A, 2005) Adsorption and kinetic
studies of cationic and anionic dyes on pyrophyllite from aqueous solutions. J. Coll.
Interf. Sci., 286, pp 53-60.
11. Gupta, V.K. and Ali, I, 2000, Utilisation of bagasse fly ash (a sugar industry waste)
for the removal of copper and zinc from wastewater. Separ. Purif. Technol., 18(2), pp
131-140.
12. He, J., Hong, S., Zhang, L., Gan, F. and Ho, Y, 2010, Equilibrium and
thermodynamic parameters of adsorption of methylene blue onto rectorite. Fresenius
Environmental Bulletin, 19 (11), pp 2651-2656.
13. Joseph, C., Bono. A., Krishnaiah, D. And Soon, K, 2007, Sorption studies of
methylene blue dye in aqueous solution by optimised carbon prepared from guava
seeds (Psidium guajava L.) Materials Science -Medziagotyra, 13(1), pp 83-87.
14. Kovacevic, Z.F., Sipos, L. and Briski, F, 2000, Biosorption of chromium, copper,
nickel and zinc ions onto fungal pellet of Aspergillus niger 405 from aqueous solution.
Food Technol. Biotechnol., 38, pp 211-216.
15. Krishnaiah, A., Rao, P.S., Reddy K.V.N.S. and Kalyani, S, 2006, Comparative
sorption of copper and nickel from aqueous solutions by natural neem (Azadirachta
indica) sawdust and acid treated sawdust. Wood Sci Technol., 41(5), pp 427- 442.
16. Luisa, Sepúlveda-Cuevas A., Contreras-Villacura, Elsa G. and Palma-Toloza, Carolyn
L, 2008, magellan peat (sphagnum magallanicum) as natural adsorbent of recalcitran
synthetic dyes. J. Soil Sc. Plant Nutr., 8(2), pp 31-43.
17. Madhavakrishanan, S., Manickavasagam, K., Vasanthakumar, R., Rasappan, K.,
Mohanraj.R. and Pattabhi, S, 2009, Adsorption of Crystal Violet Dye from Aqueous
Solution Using Ricinus Communis Pericarp Carbon as an Adsorbent E-Journal of
Chem., 6(4), pp 1109-1116.
18. Mall, I.D., Srivastava, V.C. and Aggarwal N.K, 2006, Removal of Orange-G and
Methyl Violet dyes by adsorption onto bagasse fly ash—kinetic study and equilibrium
isotherm analyses. Dyes and Pigments, 69, pp 210-223.
19. Monash, P., Niwas, R. and Pugazhenthi, G, 2011, Utilization of ball clay adsorbents
for the removal of crystal violet dye from aqueous solution Clean Techn and Environ
Policy, 13, pp 141-151.
20. Namasivayam, C., Radhika, R. and Suba, S, 2001, Uptake of dyes by a promising
locally available agricultural solid waste: coir pith. Waste Manag., 21(4), pp 381-387.
21. Nandi, B.K., Goswami, A., Das, A.K., Mondal, B. and Purkait, M.K, 2008, Kinetic
and Equilibrium Studies on the Adsorption of Crystal Violet Dye using Kaolin as an
Adsorbent Sep Sci Technol., 43(6), pp 1382–1403.
Removal of Basic Dyes from Aqueous Solutions Using Mustard Waste Ash and Buffalo Dung Ash
Harminder Singh et al
International Journal of Environmental Sciences Volume 3 No.5, 2013 1725
22. Oliveira, L.S., Franca, A.S., Alves, T.M. and Rocha, S.D.F, 2008, Evaluation of
untreated coffee husks as potential biosorbents for treatment of dye contaminated
waters. J. Hazard. Mat., 155, pp 507-512.
23. Patel, H. and Vashi, R.T, 2010, Adsorption of Crystal Violet Dye onto Tamarind Seed
Powder. E-Journal of Chemistry, 7(3), pp 975-984.
24. Patil, S., Deshmukh, V., Renukdas, S. and Patel, N, 2011, Kinetics of adsorption of
crystal violet from aqueous solutions using different natural materials. Intl J. of Envi.
Sciences, 1(6), pp 1116-1134.
25. Pavan, F.A., Mazzocato, A.C. and Gushikem, Y, 2008, Removal of Methylene Blue
dye from aqueous solutions by adsorption using yellow passion fruit peel as adsorbent.
Bioreso. Tech., 99, pp 3162-3165.
26. Porkodi, A. and Vasanthkumar, K, 2007, Equilibrium, kinetics and mechanism
modeling and simulation of basic and acid dyes sorption onto jute fiber carbon: Eosin
yellow, malachite green and crystal violet single component systems. J. of Hazardous
Material, 143 (1-2), pp 311-327.
27. Rauf, M. A., Shehadeh, I., Ahmed, A. and Al-Zamly, A, 2009, Removal of Methylene
Blue from Aqueous Solution by Using Gypsum as a Low Cost Adsorbent World
Academy of Science, Engineering and Technology, 55, pp 608-613.
28. Senthilkumar, S., Kalaamani, P. and Subburam, C.V, 2006, Liquid phase adsorption
of Crystal violet onto activated carbons derived from male flowers of coconut tree. J.
Hazard Mater., B136, pp 800-808.
29. Tahir, H., Sultan, M. and Jahanzeb, Q, 2008, Removal of basic dye methylene blue
by using bioabsorbents Ulva lactuca and Sargassum. African J. of Biotechnology,
7(15), pp 2649-2655.
30. Thirumalisamy, S. and Subbaine, M, 2010, Removal of methylene blue from aqueous
solution by activated carbon prepared from the peel of cucumis sativa fruit by
adsorption. Bioresources, 5(1), pp 419-437.
31. Velmurugan, P., Kumar, R.V. and Dhinakaran, G, 2011, Dye removal from aqueous
solution using low cost adsorbent. Intl J. of Envi. Sciences, 1(7), pp 1492-1503.
32. Wang, S., Li, H. and Xu, L, 2006, Application of zeolite MCM-22 for basic dye
removal from wastewater. J. Colloid Interface Sci., 295(1), pp 71–78.