report - guillow's - 2000fe... · 2016. 3. 25. · report bureau veritas consumer products...

REPORT

Bureau Veritas Consumer Products Services, Inc. 100 Northpointe Parkway Buffalo, NY 14228-1884 USA Tel 716.505.3300 Fax 716.505.3301 website:cps.bureauveritas.com

This report is governed by, and incorporates by reference, the Conditions of Testing as posted at the date of issuance of this report at http://cps.bureauveritas.com and is intended for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents.

Technical Report: (5116)083-0043 of 27

March 24, 2016ORIGINAL

(SAMPLE IMAGE)

http://cps.bureauveritas.com

Bureau Veritas Consumer Products Services, Inc. 100 Northpointe Parkway Buffalo, NY 14228-1884 USA Tel 716.505.3300 Fax 716.505.3301 website:cps.bureauveritas.com

This report is governed by, and incorporates by reference, the Conditions of Testing as posted at the date of issuance of this report at http://cps.bureauveritas.com and is intended for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents.

Technical Report: (5116)083-0043 March 24, 2016 Date Received: MARCH 23, 2016 Page 3 of 38

DALE BASS / RPI ,

PAUL K. GUILLOW, INC. 40 NEW SALEM STREET WAKEFIELD, MA 01880 UNITED STATES

Sample Description: #2000FE JUMBO FLYING EAGLE FOAM GLIDER - TESTINGS BAG THICKNESS. - RETEST

Vendor: PAUL K. GUILLOW, INC. Vendor ID: 85228 Sample Size: 6 Factory Name: PAUL K. GUILLOW, INC. VPN: 2000FE UPC Code: N/A SKN/SKU No.: 530059 Labeled Age Grade: 8+ PO No.: TBD Appropriate Age Grade: OVER 8 YEARS OF AGE Ref #: 85228 Client Specified Age Grade: NOT REQUESTED Country of Origin: UNITED STATES Tested Age Grade: OVER 8 YEARS OF AGE Assortment No.: N/A Li & Fung Contact: 8+ Department No.: 101 Type of Submission: VENDOR SUBMITTED

Grouping Test: YES

EXECUTIVE SUMMARY:

The sample(s) MEETS the following requirement(s):

- The requirements of test protocol CBRL-8000-US, Toys (V72)

Note: The sample(s) was evaluated to the previously failed sections. All other applicable data has been transferred from Bureau Veritas Consumer Products Services, Inc. Technical Report (5116)055-0119 dated March 2, 2016.

http://cps.bureauveritas.com

Technical Report: (5116)083-0043March 24, 2016

of 26

BVCPS Buffalo Contact Information for this Report:

Administrative Questions: Debra Kobler Phone: 716-505-3644 [email protected] Technical Questions: Mark Belstadt Phone: 716-505-3499 [email protected]

Bureau Veritas Consumer Products Services, Inc.

Mark B. Belstadt Product Test Engineer, Toys and Juvenile Products Department

/zr

mailto:[email protected]


TOYS (V72)

Evaluation Citation/Method Criteria Remark

SCOPE Toy is defined as any object designed, manufactured, or marketed as a plaything for children under 14 years of age. Game consoles and it's associated accessories are defined as General Use Product unless it is embellished or decorated with childish themes or are marketed to children as per Interpretation of "Children's Product" - 16 CFR Part 1200 and will not be covered under this protocol. Novelty toys for candies filled shall test to CBRL-8031-US Protocol.

NT

SUPPLEMENTAL PROTOCOL

* ** Federal Communications Commission (FCC) Part 15 DocumentManagement

CPSD-EL-PTCL-04999.9-NA, CPSD-

EL-01096-MTHD

Electronic products shall have complied with FCC regulations appropriate for the country of destination as shown by evaluation to the cited protocol. Products under FCC Verification or Declaration of Conformity must be submitted with complete and correct test reports. Designs claimed to be exempt from FCC equipment authorization due to an un-obvious feature (like electronic frequency), must be submitted with acceptable supporting technical documents.

NT

CPSIA Requirements CBRL-GB-PTCL-08444-US

All samples shall be reviewed against the requirements of CPSIA Requirements supplemental protocol to determine if additional testing or labeling is required. NT

*US - Food contact CPSD-AN-PTCL-06001-US

The sample shall meet requirements of supplemental Protocol CPSD-AN-PTCL-06001-US Food contact NT

*California Proposition 65 CBRL-AN-PTCL-06572-US

The sample should be reviewed against the requirements of California Proposition 65 to determine if additional testing or labeling is required.

For samples that fall under the scope of CAProp 65 requirements with testing limit(s) but does not contain appropriate labeling (refer to labeling section for detail), actual testing will be conducted. Otherwise, actual testing is not required and report as "Pass" if the sample contains appropriate labeling.

NT


of 26

TOYS (V72)


LABELING REQUIREMENTS

Packaging and Labeling Evaluation

UPLR/FPLA NIST handbook 130 part IV A Section 3, 5 &

6 16 CFR 500.4 / 16 CFR 500.5 /

16 CFR 500

• Shall be labeled with product identification.

• Shall be labeled with the manufacturer, packer, or distributor’s name and address (city, state and ZIP).

• Net quantity of contents shall be on PDP and be expressed in terms of weight or mass, measure, numerical count, or combination so as to give accurate information to facilitate consumer comparison (English and metric units).

• Glue and Adhesives sold with the product shall comply with the labeling requirements of 16 CFR 500, "Regulationsunder section 4 of the Fair Packaging and Labeling Act"

Note: evaluate only when packaging is submitted with sample. If no packaging submitted, report as "Not Tested"

NT

Instructions Visual Shall be legible and easy to understand; instructions shall be consistent with sample performance NT

Country of origin marking Country of Origin 19 CFR 134.11

Shall be marked with the country of origin when imported into the U.S. in a conspicuous place to indicate to the ultimate purchaser in the U.S., the English name of the country of origin.

• All individually packaged items shall contain the country of origin

• All items shipped in bulk or displayed in bulk must contain the country of origin

NT

Age grading CPSC Age Determination Guidelines /

16 CFR Part 1200

All products shall be tested according to either the appropriate age grade, as determined by BVCPS, or the labeled age grade if it is more stringent. In the event the sample is not age labeled, BVCPS will determine the appropriate age grade and test accordingly

NT

Stuffed Toy Labeling PA / MA / OH Stuffed Toy Law

Stuffed toys shall have a tab or label securely affixed which contains:

A statement that “All New Material” was used

Type of material

The assigned state registration number (Pennsylvania at a minimum)

The name and principal place of business (city and state) of the manufacturer or vendor

NT


of 26

TOYS (V72)


Labeling review – toys ASTM F963-11 sections 4 to 7

Shall have special labeling for specific features such as but not limited to: • Aquatic Toys• Crib And Playpen Toys• Mobiles • Strollers And Carriages • Toys Intended To Be Assembled By An Adult • Simulated Protective Devices • Toys With Functional Sharp Edges And Sharp Points • Small Objects, Small Balls, Marbles and Balloons • Toy Caps• Art Materials• Electric Toys• Battery-Operated Toys • Battery-Powered Ride On Toys• Toys In Contact With Food• Magnets

Packaging, literature accompanying toys, and point-of-sale presentations shall not use words, statements, or graphic material that are inconsistent in any way with the safety labeling instructions for use assembly or age grading of the toy. Information and instructions provided for the safe use or assembly of a toy shall be easy to read and understand by persons of the age level for whom the toy is intended. Shall be in the English language at a minimum. Either a principal component of a toy or the packaging of a toy shall be marked with the name and address of the producer or the distributor.

NT

16 CFR 1500.130 Pressurized container labeling

16 CFR 1500.130 Self-pressurized containers shall conform to the labeling requirements as defined by 16 CFR 1500.130 NT

Bedding And Upholstered Furniture Labeling

Association of Bedding and Furniture

All filling materials shall have a securely affixed tag or label which contains the following information: • The statement, “UNDER PENALTY OF LAW THIS TAG NOT TO BE REMOVED EXCEPT BY THE CONSUMER” • A description of the filling contents preceded by the statement, “ALL NEW MATERIALS CONSISTING OF”• The assigned state number (i.e. REG. NO. PA”)• The statements, “Certification is made by the manufacturer that the materials in this article are described in

accordance with law”.

NT


of 26

TOYS (V72)


Toy Gun Marking 15 CFR 1150 / ASTM F963-11 section 4.30

Sample shall comply with the requirements as defined in 15 CFR 1150 NT

16 CFR 303 Textile labeling 16 CFR 303 Shall have a label securely affixed that contains: • The name and manufacturer or other marketing or registration number • The country of origin • The generic name and percentage of all fibers in the product

NT

16 CFR 423 Care labeling review 16 CFR 423 Shall have a label securely affixed that contains regular care (customary and routine) information. NT

16 CFR 1500.83(a)(23) Chemistry set labeling

16 CFR 1500.83(a)(23) Chemistry sets, science education sets and replacement chemicals for such sets, are exempt from section 2(p)(1) of the Federal Hazardous Substances Act if (i) the immediate container of hazardous chemical bears on its main panel the name, appropriate signal word, and

additional statement “Read back (or side) panel before using” and bears on the back (or side) panel the remainder of the appropriate cautionary statement;

(ii) the experiment manual or other instruction book or booklet bears the following caution statement within the borders of a rectangle and in the type size specified in 1500.121: WARNING - This set contains chemicals that may be harmful if misused. Read cautions on individual containers carefully. Not to be used by children except under adult supervision.

(iii) the outer carton bears on the main panel the caution statement specified in (ii).

NT

Labeling of hazardous substances 16 CFR 1500.3(b)(14)(i) / 16

CFR 1500.14(b)(1-5) / 16 CFR 1500.121 /

CPSD-GB-08615.01-MTHD

Applicable to toxic, skin irritant, eye irritant, corrosive, strong sensitizer, extremely flammable, flammable, combustible and hazardous substance requiring special labeling according to 16 CFR 1500.14 (b)(1-5).

Product containing hazardous substances shall conform to and be consistent with the labeling requirements as defined by 16 CFR 1500.3(b)(14)(i) and special labeling requirement according to 16 CFR 1500.14 (b)(1-5).

Note: Only labeling review of defined "signal words", "statement(s)" and "principal hazards(s)" are conducted. Other materials, i.e. generic chemical name, precautionary measures, first -aid, instructions are reported as data only. Information not on PDP is not evaluated. The act also provides exemptions for the labeling of hazardous substance according to 16 CFR 1500.83, which is not included in the evaluation of labeling of hazardous substances.

NT

21 CFR 101 Food labeling

21 CFR 170-189 Food ingredient list review

21 CFR 101

21 CFR 73, 74, 82 and 170 through 189

Food and Nutritional labeling shall be evaluated in accordance with the required size, format, contents, etc. as defined by the regulation. (Vendor shall be responsible for the accuracy of information contained) Additives and colors contained in the ingredients list shall be evaluated in accordance with the approved list of ingredients as defined by the regulation. (Vendor shall be responsible for the accuracy of information contained)

NT

FDA cosmetic labeling review ASTM F963-11 section 4.3.4 / 21 CFR 701 and

740

Cosmetics labeling shall be evaluated in accordance with the required size, format, contents, etc. as defined by the regulation.

Note: Vendor shall be responsible for the accuracy of information contained

NT


of 26

TOYS (V72)


FDA ingredient list evaluation ASTM F963-11 section 4.3.4 / 21 CFR 73, 74,

82, 700 and 701

Ingredient and colors contained in the ingredients list shall be evaluated in accordance with the approved list of ingredients as defined by the regulation.


NT

Illinois lead warning label Illinois Lead Poisoning Prevention Act

Product shall not contain the following Illinois lead warning label per client's requirement. Refer to the analytical section for details.

"WARNING: CONTAINS LEAD. MAY BE HARMFUL IF EATEN OR CHEWED. COMPLIES WITH FEDERAL STANDARDS."

NT

Phthalates-Free Claim CPSD-HL-01057-MTHD

The product and/or packaging shall not contain a "Phthalates free" or equivalent claim. NT

SAFETY REQUIREMENTS

Mechanical hazards - toys ASTM F963-11 section 4

Shall meet the requirements specified in the standard. M

Mechanical hazards - lawn darts 16 CFR 1500.18(a)(4) Lawn darts and other similar sharp-pointed toys usually intended for outdoor use and having the potential for causing puncture wound injury. The supply of these goods is banned. NT

Mechanical hazards - clacker ball 16 CFR 1500.18(a)(7) Shall comply with the requirements specified in 16 CFR 1500.86(a)(5). NT

Rattles 16 CFR 1510 / ASTM F963-11 section 4.23

Rattles shall meet the safety requirements as specified in 16 CFR 1510 NT

Pacifiers 16 CFR 1511 / ASTM F963-11 section 4.20

Samples shall meet the safety requirements as specified in 16 CFR 1511 if nipple length longer than 0.63 inch NT

16 CFR 1500 Dive stick 16 CFR 1500 Samples shall meet the safety requirements as specified in 16 CFR 1500 NT

21 CFR 801.410 FDA Lens impact - doc review

21 CFR 801.410(c) Shall be fitted with impact-resistant lenses to protect the consumer from potential eye injuries. Lenses shall meet an AQL of 6.5 as specified in 21 CFR 801.410 when subjected to FDA using MIL-STD 105E or FDA approved statistical sampling plan. In lieu of testing, test report can be submitted if dated within one year. It is the vendor's responsibility to assure the manufacturer is registered under the FDA. NOTE: The documentation requirements of 21 CFR 801.410 (f) are the responsibility of the manufacturer.

NT

NY Restriction of sale of Yo-Yo Waterball

Section 399 General Business Law/

A472

No person, firm, corporation, or association shall import, manufacture, sell, offer to sell, or distribute a Yo-Yo waterball toys.

"Yo-Yo waterball toy" means a yo-yo waterball, water yo-yo, or any similar toy made of rubber or rubberlike material consisting of a ball that is filled with a liquid and attached to an elastic cord with a finger loop at the end.

NT

Flammability of solids 16 CFR 1500.44 / 16 CFR 1500.3(c)(6)(vi) / ASTM F963-11 section

4.2 Annex A5

Shall not exceed the maximum allowable limit of no greater than 0.1 inches per second NT


of 26

TOYS (V72)


Flash point of combustible liquid 16 CFR 1500.3(c)(6)(iii) / 16CFR 1500.43(a) CPSD-GB-00019-

MTHD

All liquid items for children aged 8 years and under shall have flash point greater than 150 °F or 65.6 °C.

Remark: - For products intended for children aged over 8 years, if the liquid items are classified as either combustible, flammable orextremely flammable, it shall conform to the labeling of hazardous substances. - Liquid is defined as any material which is free flowing, has no fixed shape and would take the shape of its container.

NT

Flammability of self-pressurized containers

16 CFR 1500.3(c)(6)(viii) / 16

CFR 1500.45

Self-pressurized container for children aged 8 years and under shall not be flammable when tested in according to 16 CFR 1500.45.

Remark: For products intended for children aged over 8 years, if the contents of the self-pressurized containers are classified as either flammable or extremely flammable, it shall conform to the labeling of hazardous substances.

NT

Flammability of clothing textiles 16 CFR 1610 / ASTM F963-11 section 4.2 /

Annex A6

Textile fabrics used in toys should comply with 16 CFR 1610 as applicable NT

16 CFR 1610 Flammability (costume)

16 CFR 1610 Costumes should comply with 16 CFR 1610 as applicable NT

16 CFR 1611 Flammability (vinyl plastic film)

16 CFR 1611 Textile fabrics used in toys should comply with 16 CFR 1611 as applicable NT

CPAI-75 Flammability (sleeping bags) - doc review

CPAI-75 Materials shall comply with the requirements as defined. In lieu of testing, test report can be submitted if dated within one year. NT

CPAI-84 Flammability (camping tentage) - doc

CPAI-84 Materials shall comply with the requirements as defined. In lieu of testing, test report can be submitted if dated within one year. NT

Drawstrings / Ties on children upper outerwear

16 CFR 1120 / Visual or Actual Measurement

Hood and Neck Area On Upper Outerwear (Sizes 2T-12) Hood and neck drawstrings/ties are not allowed at all on any children’s upper outerwear (outerwear including jackets and sweatshirts).

Waist and Bottom Area On Upper Outerwear Garments (Sizes 2T-16) Drawstrings/ties may not exceed 3 inches (75mm) in length on each side outside the drawstring channel when garment is expanded to its fullest width. Drawstrings/ties must be bartacked at center back so string cannot be pulled out. No toggles, knots or attachment at the free ends. Must be finished at both ends.

Note For S, M, L, XL sizing Girls and Boys size (L) is equivalent to size 12 and Girls and Boys size (XL) is equivalent to size 16.

NT


of 26

TOYS (V72)


Drawstrings New York State Law 391.b and amendmentand Wisconsin State

Law ATCP 139 / Visualor Actual Measurement

(Sizes 0-16) Hood and Neck Area Hood and neck drawstrings are not allowed at all on any children’s clothing (outerwear and non-outwear).

Waist On Upper Garments (tops, jackets, dresses) and Bottoms (pants, shorts, skirts) May not exceed 3 inches (75mm) in length on each side outside the drawstring channel when garment is expanded to its fullest width. Drawstrings must be bartacked at center back so string cannot be pulled out. No toggles, knots or attachment at the free ends. Must be finished at both ends.

NT

Total lead content in surface coatings

Illinois Lead Poisoning Prevention

Act / CPSC-CH-E1003-09.1 / CPSD-

AN-00001-MTHD

The following surface coatings shall contain less than 0.004% (40ppm) lead or lead compounds in which the lead content is the weight of the total content: a. All accessible surface coatings, in the as received state, on jewelry for children under 12 years of age, b. All accessible surface coatings, before and after use and abuse testing, on child care articles for children 6 years of

age or younger, and on toys for children under 12 years of age. As a client requirement, the warning label is not allowed.

In case of insufficient coating for testing found on the number of samples specified in the protocol, vendor needs to provide additional samples/component parts (including raw materials) for testing. The vendor is responsible for compliance of all other products outside of the above scope.

Report actual results or include data table within report. Component testing is allowed. Compositing is not allowed.

NT


of 26

TOYS (V72)


Total lead content in substrate materials

Illinois Lead Poisoning Prevention

Act / CPSC-CH-E1001-08.3 / CPSC-

CH-E1002-08.3/ CPSD-AN-00185-

MTHD / CPSD-AN-00196-MTHD

The following substrate materials shall contain less than 0.004% (40ppm) lead or lead compounds in which the lead content is the weight of the total content: a. All accessible substrate materials, in the as received state, on jewelry for children under 12 years of age, b. All accessible substrate materials, before and after use and abuse testing, on child care articles for children 6 years of

age or younger.As a client requirement, the warning label is not allowed.

In case of insufficient material for testing found on the number of samples specified in the protocol, vendor needs to provide additional samples/components/parts for testing. Materials exempted from testing under CPSIA (e.g., textiles) under 16 CFR 1500.88 and 1500.91 (d) and (e) will not be tested. The vendor is responsible for compliance of all other products outside of the above scope.


NT

Total cadmium content in surface coatings

AOAC 974.02:2005 modified / acid

digestion, ICP analysis

All accessible surface coatings , before and after use and abuse testing, on jewelry intended for children ages 12 and under shall not contain cadmium in excess of 0.004% (40ppm) of the weight of the total content.

Report actual results or include data table within report. No compositing.

Until legislation is enacted, this is a client requirement.

NT

Total cadmium content in substrate materials

CPSC-CH-E1002-08

(modified) / CPSC-CH-E1001-08 (modified) /

acid digestion, ICP analysis

All accessible plastic and metal substrate materials, before and after use and abuse testing, of jewelry intended for children ages 12 and under shall not contain cadmium in excess of 0.004% (40ppm) of the weight of the total content.



NT


of 26

TOYS (V72)


Total heavy metal contents in surface coatings

ASTM F963-11 section 4.3.5.1 (2) and 8.3.1 / CPSC-CH-E1003-09 /

CPSD-AN-00564-MTHD

All accessible surface coating, before and after use and abuse testing, shall not contain compounds of which the metal content of the total content exceeds the levels by weight (mg/kg) of the contained solid including pigments, film solids and driers [Antimony (Sb) 60, Arsenic (As) 25, Barium (Ba) 1000, Cadmium (Cd) 75, Chromium (Cr) 60, Lead (Pb) 90, Mercury (Hg) 60, Selenium (Se) 500]

Report actual results or include data table within report. If all heavy metal limits except for lead are met then no soluble lead testing will be conducted when the CPSIA total lead requirement is not met. Component testing is allowed. Based on the standard, will composite up to 3 colors. If any color in the composite exceeds 80% of the limit of any heavy metal except for lead based on the lowest weight component then soluble heavy metal content test with individual colors will be analyzed.

NT

Soluble heavy metal contents in surface coatings

ASTM F963-11 section 4.3.5.1 (2) and 8.3.2 /

CPSD-AN-00564-MTHD

All accessible surface coating, before and after use and abuse testing, shall not contain compounds of which the metal content of the soluble material exceeds the levels by weight (mg/kg) of the contained solid including pigments, film solids and driers [Antimony (Sb) 60, Arsenic (As) 25, Barium (Ba) 1000, Cadmium (Cd) 75, Chromium (Cr) 60, Lead (Pb) 90, Mercury (Hg) 60, Selenium (Se) 500]

Coating materials that contain less than the total limit of [Antimony (Sb) 60, Arsenic (As) 25, Barium (Ba) 1000, Cadmium (Cd) 75, Chromium (Cr) 60, Lead (Pb) 90, Mercury (Hg) 60, Selenium (Se) 500] do not need to be tested for the soluble content.


NT


of 26

TOYS (V72)


Total heavy metal contents in substrate

ASTM F963-11 section 4.3.5.2 (2) (b) and 8.3.1 / 16 CFR 1251 / CPSC-

CH-E1001-08.1 / CPSC-CH-E1002-08.1

/ CPSD-AN-00564-MTHD

All accessible substrates, before and after use and abuse testing, shall have total heavy metals content comply with the limits specified in Table 1 of the standard. [Antimony (Sb) 60 mg/kg, Arsenic (As) 25 mg/kg, Barium (Ba) 1000 mg/kg, Cadmium (Cd) 75 mg/kg, Chromium (Cr) 60 mg/kg, Lead (Pb) 90 mg/kg, Mercury (Hg) 60 mg/kg, Selenium (Se) 500 mg/kg]

Report actual results or include data table within report. If all heavy metal limits except for lead are met then no soluble lead testing will be conducted when the CPSIA total lead requirement is not met. Conduct soluble heavy metal test directly if there is only one textile component in the product.

Component testing is allowed. Based on the standard, will composite up to 3 like materials. If any material in the composite exceeds 80% of the limit of any heavy metal except for lead based on the lowest weight component then soluble heavy metal content test with individual material will be analyzed. Unfinished and untreated wood as defined in 16 CFR 1251 will not be tested.

NT

Soluble heavy metal contents in substrate

ASTM F963-11 section 4.3.5.2 (2) (b) and 8.3.5 / 16 CFR 1251 / CPSD-

AN-00564-MTHD

All accessible substrates, before and after use and abuse testing, shall have soluble heavy metals content comply with the limits specified in Table 1 of the standard. [Antimony (Sb) 60 mg/kg, Arsenic (As) 25 mg/kg, Barium (Ba) 1000 mg/kg, Cadmium (Cd) 75 mg/kg, Chromium (Cr) 60 mg/kg, Lead (Pb) 90 mg/kg, Mercury (Hg) 60 mg/kg, Selenium (Se) 500 mg/kg]

Substrates that contain less than the total limit of [Antimony (Sb) 60 mg/kg, Arsenic (As) 25 mg/kg, Barium (Ba) 1000 mg/kg, Cadmium (Cd) 75 mg/kg, Chromium (Cr) 60 mg/kg, Lead (Pb) 90 mg/kg, Mercury (Hg) 60 mg/kg, Selenium (Se) 500 mg/kg] do not need to be tested for the soluble content.

Report actual results or include data table within report. Component testing is allowed. Compositing is not allowed. Unfinished and untreated wood as defined in 16 CFR 1251 will not be tested.

NT


of 26

TOYS (V72)


Total heavy metals contents in modeling clay

ASTM F963-11 section 4.3.5.2 (2) (b) and 8.3.1

/ CPSC-CH-E1002-08.1 / CPSD-AN-

00564-MTHD

Modeling clay included as part of a toy shall have total heavy metals content comply with the limits specified in Table 2 of the standard. [Antimony (Sb) 60 mg/kg, Arsenic (As) 25 mg/kg, Barium (Ba) 250 mg/kg, Cadmium (Cd) 50 mg/kg, Chromium (Cr) 25 mg/kg, Lead (Pb) 90 mg/kg, Mercury (Hg) 25 mg/kg, Selenium (Se) 500 mg/kg]


NT

Soluble heavy metals contents in modeling clay

ASTM F963-11 section 4.3.5.2 (2) (b) and 8.3.5


Modeling clay included as part of a toy shall have soluble heavy metals content comply with the limits specified in Table 2 of the standard. [Antimony (Sb) 60 mg/kg, Arsenic (As) 25 mg/kg, Barium (Ba) 250 mg/kg, Cadmium (Cd) 50 mg/kg, Chromium (Cr) 25 mg/kg, Lead (Pb) 90 mg/kg, Mercury (Hg) 25 mg/kg, Selenium (Se) 500 mg/kg]

Modeling clay that contain less than the total limit of [Antimony (Sb) 60, Arsenic (As) 25, Barium (Ba) 250, Cadmium (Cd) 50, Chromium (Cr) 25, Lead (Pb) 90, Mercury (Hg) 25, Selenium (Se) 500] do not need to be tested for the soluble content.


NT

Extractable cadmium content in metal

ASTM F963-11 section 4.3.5.2 (2) (c) and

8.3.5.5 (3) / CPSC-CH-E1004-11 / CPSD-AN-

00564-MTHD

All accessible metal component of toy, that is a small part, before and after use and abuse testing, shall not contain more than 200 micrograms of cadmium per component.

Metal that contain less than 75 ppm total cadmium do not need to be tested for the extractable content.


NT

Total cadmium content in metal ASTM F963-11, section 4.3.5.2 (2) (c) / CPSC-

CH-E1001-08.1 / CPSD-AN-00564-

MTHD

All accessible metal component of toy, that is a small part, before and after use and abuse testing, shall not contain cadmium in excess of 0.0075% (75ppm) of the weight of the total content (which is a screening limit).


NT

21 CFR 700.13 Mercury in cosmetics

21 CFR 700.13 Shall not contain more than 0.0065% of mercury for cosmetics intended for use with the eyes and 0.0001% of mercury for other cosmetics. NT


of 26

TOYS (V72)


*Total mercury content in batteries Mercury-Containing and Rechargeable

Battery Management Act U.S. Pub. L. 104-

142 Title II / CPSD-AN-00078-MTHD

Batteries shall comply with one of the following requirements:

(i) Alkaline-manganese button cell shall contain less than 25 mg Hg / cell. (ii) Alkaline-manganese battery and Zinc carbon battery shall contain no intentionally added mercury (BV reporting limit is 4 mg/kg). (iii) No Mercuric-oxide button cell or battery is allowed.

Actual testing would be conducted on button cell batteries. It is the vendor’s responsibility for the conformity to this requirement for other batteries.

NT

*Total mercury content in button cellbatteries

Various US State Laws / CPSD-AN-00078-

MTHD

Button cell battery shall not contain any detectable levels of mercury (BV reporting limit is 4 mg/kg). NT

GRAS – FDA Stainless Steel Guidelines – Documentation Review

FDA Generally Recognized as Safe (GRAS) Guidelines

Shall meet FDA GRAS Guidelines. Documentation shall be provided. If no documentation is provided, testing will be conducted.

In lieu of testing, document may be submitted if dated within One year

NT

*Transmittance properties forsunglasses and eyewears

ANSI Z80.3-2010 clause 4.6.1 to 4.6.3, 4.6.5, 4.7.3 to 4.7.4 and 4.8 / CPSD-AN-

00102-MTHD

Non-prescription sunglasses and fashion eyewear shall comply with the requirements. Sunglasses containing a UVA/UVB protection, Traffic signal recognition and/or other ANSI Z80.3 claim will be tested to substantiate such claims.

NT

CONEG - doc review CONEG This environmentally motivated legislation regulates the amount of lead, cadmium, hexavalent chromium and mercury allowed in packaging materials. It is the vendor’s responsibility for the conformity of this requirement.

NR

*Pyrotechnic Composition 16 CFR 1507.11 Modified

Party poppers (also known as champagne party poppers and party surprise poppers) and Christmas crackers shall contain no more than 0.25 grains (16.2 mg) of pyrotechnic material.

Modification: expand the scope to include Christmas crackers

NT

LHAMA evaluation in art materials - document review

16 CFR 1500.14(b)(8) / ASTM D4236-94 (R 2011) / CPSD-GB-

00001-MTHD

Art materials intended for use by children, including toys and parts of toys, shall not pose any chronic health hazards. Toxicity Risk Assessment shall be conducted.

In lieu of testing, test report can be submitted if dated within five years.

NT


of 26

TOYS (V72)


Toxicological risk assessment - document review

ASTM F963-11 section 4.3.1 and 8.2 / 16 CFR

1500.3 (b)(5) and 1500.3 (b)(7)-(9) / CPSD-GB-00001-

MTHD

Products intended for use by children, including toys and parts of toys, must not be toxic a skin irritant, eye irritant, corrosive, or a strong sensitizer.

Toxicological Risk Assessment shall be conducted to substantiate the compliance of the regulation for the following components: - The following high risk materials: All toy cosmetics, liquids, pastes, putties, gels and powders regardless of claim - Other materials bearing a "NON-TOXIC" claim on samples and/or its packaging


NT

Hazardous substances in liquid – document review

16 CFR 1500.14(a)(1-5) / CPSD-GB-00001-

MTHD

To identify the presence of potentially hazardous ingredients, all liquid components and liquid-filled items designed or intended to be used by individuals over 8 years old containing substances exceeding the following limits require special labeling:

a. 10% or more by weight of ethylene glycolb. 10% or more by weight of diethylene glycolc. 4% or more by weight of methanold. 10% or more by weight of petroleum distillates e. 5% or more by weight of benzenef. 10% or more by weight of turpentine g. 10% or more by weight of tolueneh. 10% or more by weight of xylene

Note: - Liquid is defined as any material which is free flowing, has no fixed shape and would take the shape of its container.

In lieu of testing, test report can be submitted if dated within one year.

NT


of 26

TOYS (V72)


Hazardous liquids – document review

16 CFR 1500.231 / CPSD-GB-00001-

MTHD

To identify the presence of potentially hazardous ingredients, all liquid components and liquid-filled items intended or likely to be used by children aged 8 years and under shall comply with this requirement and the following chemicals shall not be present:

a. Ethylene glycolb. Diethylene glycol c. Methanold. Mercury e. Methylene chloridef. Petroleum distillatesg. Tolueneh. Xylenei. Benzenej. Turpentine

Note: - Liquid is defined as any material which is free flowing, has no fixed shape and would take the shape of its container. - This includes liquids that are sealed in a product and BV expands to un-sealed liquid (16 CFR 1500.14).


NT

DEHP Content ASTM F963-11 section 4.3.8 / ASTM D3421:75


Pacifiers, rattles, and teethers shall not intentionally contain Di (2-ethylhexyl) phthalate. Shall not contain more than 3% of total solid. NT

Nitrosamines content in rubber pacifiers - document review

ASTM F963-11 section 4.20.1 / ASTM F1313-

90(R2011) / CPSD-GB-00001-MTHD

Rubber nipple on pacifier shall comply with following requirements:

a. Shall not contain more than 10 ppb in each of three aliquots of any one nitrosamine, b. Shall not contain more than 20ppb of total nitrosamines.


NT

*Nitrosamines in rubber pacifier ASTM F963-11 section 4.20.1 / ASTM F1313-

90(R2011)

Rubber nipples on pacifiers shall comply with following requirements:


NT

PA stuffed toy law tolerance - document review

ASTM F963-11 section 4.3.7

Loose fillers shall be visually evaluated for objectionable matter and labels shall be evaluated accordingly.

Shall meet the requirements of the “Tolerances of the Commonwealth of Pennsylvania Regulation for Stuffed Toys”. In lieu of testing, test report can be submitted if dated within one year.

NT


of 26

TOYS (V72)


Total plate count and total coliform ASTM F963-11 section 4.3.6.1 / Bacteriological

Analytical Manual (BAM) / CPSD-AN-00034, 35-MTHD

Pure water used in filling of toys shall meet the requirements of < 100 CFU/ml of total plate count and < 1 CFU/100ml of total Coliform. NT

Microbial limit test - document review

ASTM F963-11 section 4.3.6.3 and 8.4.1 / USP

31<61> / CPSD-GB-00001-MTHD

Cosmetics, liquids, pastes, putties, gels and powders used in toys (excluding art materials) shall not be contaminated with Salmonella, E. Coli, Pseudomonas aeruginosa, or Staphylococcus aureus and be subject to requirements of less than or equal to 5,000 CFU/ml (less than or equal to 500 CFU/ml for cosmetics intended for use with the eyes and baby products) for total viable count (total plate count + yeast & mold count) as intended to minimize risk associated with lack of cleanliness, shelf life and contamination.


Note: In order to ensure the integrity of the received test report, actual testing on total plate count would be conducted (Refer to Total plate count test line for detail.).

NT

Total plate count USP 31 <61> / CPSD-AN-00035-MTHD

Cosmetics, liquids, pastes, putties, gels and powders shall have total plate count less than or equal to 5,000 CFU/ml (less than or equal to 500 CFU/ml for cosmetics intended for use with the eyes and baby products).

Client requirement

NT

Preservative effectiveness - document review

ASTM F963-11 section 4.3.6.3 and 8.4.2 / USP

35<51> / CPSD-GB-00001-MTHD

Formulations used to prevent microbial degradation in cosmetics, liquids, pastes, putties, gels and powders used in toys (excluding art materials) shall be tested for microbial control and preservative effectiveness.

In lieu of testing, test report can be submitted if dated within two years.

NT

Battery-powered ride-on toys ASTM F963-11 section 4.25.10

Samples shall meet the safety requirement as specified in ASTM F963-11, section 4.25.10 NT

Electrically operated toys 16 CFR 1505 / ASTM F963-11 section 4.4

Toys operating from nominal 120-V branch circuits shall conform to the requirements of 16 CFR 1505 NT

UL Testing (For electrically operated product)

UL Standard Item will be audited to verify compliance with the selected sections of the applicable and/or labeled UL standard. NT

Safety Agency Listing Verification E – 1090 Verify Client Acceptable Safety Agency Listing by contacting Listing Agency with the sample's Listing Number, Manufacturer, Model Number, and/or Agency Control Number. Shall be verified. NT

AATCC 20A Quantitative 16 CFR 303 Shall be tested to substantiate fiber content. Shall not exceed a deviation of + 3% from the label as allowed for blends and no deviation for items labeled 100% of a fiber. NT


of 26

TOYS (V72)


Wearing Apparel – Care Label 16 CFR 423 For wearing apparel covered by 16 CFR 423: With care label: Conduct laundry test according to the labeled care instruction. Evaluate for general appearance as acceptance criteria. Without care label: Failed for labeling requirement. No softline test will be conducted.

For wearing apparel not covered by 16 CFR 423: With care label: Conduct laundry test according to the labeled care instruction. Evaluate for general appearance as acceptance criteria. Without care label: No softline test is required.

NT

BBP / DBP / DEHP content

DnOP / DINP / DIDP content

DnHP content

CPSD-AN-00095-MTHD /

CPSD-AN-00143-MTHD

The following products outside of the scope of CPSIA, in the as received state, shall not contain concentrations of more than 0.1% BBP, DBP DEHP, DINP, DIDP, DnOP, DnHP individually: Report actual results or include data table within report.

Component testing is allowed. Actual testing would be conducted on accessible high risk (listed below) plastics materials. a. Poly vinyl chloride (PVC) b. Poly vinylidene chloride (PVDC) c. Poly vinyl acetate (PVAc)d. Poly urethane (PU)e. Ethylene propylene diene monomer rubber (EPDM) f. Ethylene vinyl acetate (EVA)g. Other foam plastics (except polyolefins)h. Natural and synthetic rubberi. Siliconej. Thermoplastic elastomers (TPEs)k. Plastic materials other than polyolefins with shore A hardness < 90Composite up to 3 like materials. The composite result (based on material weight) will be evaluated against the adjustedlimit (regulatory limit divided by the number of components in the composite). If composite fails and ON REQUEST, individual components will be analyzed.Client Requirement

NT


of 26

TOYS (V72)


*Bisphenol A content Various state laws (e.g. CT Public Act # 09-103 and MN Chapter 40 SF

#247) / 21 CFR 177.1580 / CPSD-AN-

00169-MTHD

The following products shall not contain any detectable levels of Bisphenol-A (BPA) (BV reporting limit is 0.1mg/kg): - Infant formula/ baby food plastic container, jar or can - All reusable food or beverage containers including lids (if any) - Baby bottle liners - Pacifiers - Straws

"Infant formula" means a commercially available milk based or soy based powder, concentrated liquid or ready-to-feed substitute for human breast milk that is intended for infant consumption."Baby food" means a commercially available prepared solid food consisting of a soft paste or an easily chewed food that is intended for consumption by children two years of age or younger."Reusable food or beverage container" means a receptacle for storing food or beverages, including, but not limited to, baby bottles, spill-proof cups, sports bottles and thermoses, and excluding containers intended for disposal after initial use.

Report actual results or include data table within report.

Note: - Actual testing will be conducted on all accessible polycarbonate, and epoxy resin materials only, including both coatingsand substrates- Vendors shall provide documentation or a bill of material for material identification. If they cannot provide surface coating material information, all coatings ( except lacquer and paint) will be tested. - Vendors shall be responsible for the compliance of all other materials. - Testing will not be conducted on food contact polycarbonate resins in infant feeding bottles (baby bottles) and spill-proof cups including their closures and lids, designed to help train babies and toddlers to drink from cups (sippy cups), becausefood contact polycarbonate resin are banned in these products by 21 CFR 177.1580.- Composite all colors of surface coating to perform one test.

NT

WORKMANSHIP AND PERFORMANCE REQUIREMENTS

Function Per instruction or intended use

Shall function as intended NT

Air Leakage For Inflatable Pool Items

Per Criteria Inflatable pool items (e.g. inflatable pool, swimming rings, etc.) which are intended to bear the mass of children shall be evaluated for air leakage for duration of one hour. NT

Dishwasher Claim Verification Per Criteria Items containing a dishwasher safe claim will be subjected to 5 normal cycles and evaluated for any color change, warping, breaking, leaking or other defects. NT

Microwave Claim Verification Per Criteria Items containing a microwave safe claim will be subjected to 10 normal cycles and evaluated for any color change, warping, breaking, leaking or other defects. NT

Freezer Claim Verification Per Criteria Items containing a freezer safe claim will be subjected to 3 freeze/thaw cycles and evaluated for any color change, warping, breaking, leaking or other defects. NT


of 26

TOYS (V72)


Battery-operated Items NT

Internal Mechanical / Electrical Mechanism (if applicable)

Visual Visual evaluation only, NO PASS or FAIL rating will be given. Provide supporting photograph(s) in the report of major components such as wiring, linkages, printed circuit boards, motors, lighting assemblies, musical assembles, frames, etc. in relation to poor assembly and / or inferior materials, including worn parts, rust or other corrosion, loose connections, contaminations, etc.

Note that if samples are deemed difficult to open and / or may damage internal mechanism as a result of opening then state "Not Tested" with remark.

NT

Battery Insertion / Removal CPSD-HL-01058-MTHD / Visual

Insert and remove the batteries 100 cycles, turning the unit on for 10 seconds each cycle.

Shall function as claimed for each cycle.

If failure is noted before 100 cycles, report the number of cycles at failure and the type of failure.

NT

*Extended Performance CPSD-GB-01058-MTHD

Assemble as instructed. Insert the recommended number and type of batteries. This test should be conducted for 8 hours. Operate continuously until the batteries have drained or 8 hours of operation was completed. During and / or at the end of period, check for visual signs of failure, including heat buildup, mechanical problems, etc.

After batteries have drained at the end, wait at least 10 minutes before inserting fresh, new batteries, and resuming the remaining of total 8 hours of operation.

Shall exhibit no failures.

If failure is noted before the end of the 8 hours operation, report duration and the type of failure.

Note the sample shall not be left operating unsupervised.

Client's requirements: Brands of battery used shall be Rayovac.

NT


of 26

TOYS (V72)


*Battery Compartment Fitment Test CPSD-HL-01058-MTHD /

Actual use

[Only apply to replaceable battery type of battery operated items] [Does not apply to button cell battery powered items]

Use 3 major brands of appropriate size batteries (like Rayovac, Duracell, and Energizer), the battery/batteries shall fit in the compartment and shall be function as intended.

Report battery brands being used for the testing.

Client's requirements: 3 brands of batteries used shall be Duracell, Energizer and Rayovac.

Test also the batteries that come with the product if applicable.

NT

Battery Reverse Voltage Test CPSD-HL-01058-MTHD / Actual use

Reversing battery orientation shall not damage unit. NT

Electrical Plug-in items (not battery operated) NT




NT

Extended Performance – 48 hours CPSD-HL-01058-MTHD / Visual

Assemble as instructed. Operate continuously for 8 hour periods for a total of 6 periods. During and / or at the end of each period, check visual signs of failure, including heat buildup, mechanical problems, etc.

Shall exhibit no failures for 48 hours.

If failure is noted before the end of the 48 hours, report duration and the type of failure.



NT

IMPORTANT NOTE: The information presented under the "Criteria" of this protocol is for information only and does not replace the content of the standard. Details of the requirements should be referred to the original standards.


of 26

Rating Key: M Meets NM Does Not Meet NA Not Applicable NR Not Requested

Testing Parameter Age (Months) Abuse Test Conditions

Drop Test 0 to ≤18 >18 to ≤36 >36 to ≤96

4.5 ft (1.37 m), 10 drops 3 ft (0.91 m), 4 drops 3 ft (0.91 m), 4 drops

Torque Test 0 to ≤18 >18 to ≤36 >36 to ≤96

2 in - lb (0.23 N - m) 3 in - lb (0.34 N - m) 4 in - lb (0.45 N - m)

Tension Test 0 to ≤18 >18 to ≤36 >36 to ≤96

10 lb (44.5 N)

15 lb (66.8 N) 15 lb (66.8 N)

Compression Test 0 to ≤18 >18 to ≤36 >36 to ≤96

20 lb (89 N) 25 lb (111.3 N) 30 lb (133.5 N)

No. of samples required for complete testing: Toys and Hardgoods (case by case for assortments) 12 Dinnerware, Mugs, Pitchers, etc (decorated lip/rim) 12 (18) Creation Date: MARCH 7, 2006 Product contain Fiber Content 1 additional

Editorial Revision Date: DECEMBER 29, 2015

Product contain Care Label Minimum additional 2 pcs and 1 Pricing Review Date MAY 20, 2010 additional pc for each care instruction Technical Review Date MAY 20, 2010

No. of working days for complete testing 5 Revision No: 72

REPORT


100 Northpointe Parkway

Buffalo, New York 14228

Telephone: (716) 505-3300 Fax: (716) 505-3301

website: www.bureauveritas.com/cps

This report is governed by, and incorporates by reference, the Conditions of Testing as posted at the date of issuance of this report at

http://www.bureauveritas.com/cps and is intended for your exclusive use. Any copying or replication of this report to or for any other person or entity, or

use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples

identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample

was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results

thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or

omission caused by our negligence; provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A

failure to raise such issue within the prescribed time shall constitute you unqualified acceptance of the completeness of this report, the tests conducted

and the correctness of the report contents.

Technical Report: (5116)055-0119 Page 1 of 35

March 2, 2016

ORIGINAL

(SAMPLE IMAGE)

http://www.bureauveritas.com/cps



Page 2 of 35

TRACKING LABEL ON PRODUCT


Page 3 of 35

LABELING ON PACKAGING

Bureau Veritas Consumer Products Services, Inc. 100 Northpointe Parkway Buffalo, New York 14228 Telephone: (716) 505-3300 Fax: (716) 505-3301 website: www.bureauveritas.com/cps

This report is governed by, and incorporates by reference, the Conditions of Testing as posted at the date of issuance of this report at http://www.bureauveritas.com/cps and is intended for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence; provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute you unqualified acceptance of the completeness of this report, the tests

Technical Report: (5116)055-0119 March 2, 2016 Date Received: February 24, 2016 Page 4 of 35

DALE BARKER PAUL K. GUILLOW, INC. 40 NEW SALEM STREET WAKEFIELD, MASSACHUSETTS 01880 UNITED STATES

FAILSample Description: #2000FE JUMBO FLYING EAGLE FOAM GLIDER Vendor: PAUL K. GUILLOW, INC. Vendor ID: 85228 Sample Size: 3 Factory Name: PAUL K. GUILLOW INC. VPN: 2000FE UPC Code: N/A SKN/SKU No.: 530059 Labeled Age Grade: AGES 8+ PO No.: TBD Appropriate Age Grade: OVER 8 YEARS OF AGE Ref #: N/A Client Specified Age Grade: NOT REQUESTED Country of Origin: UNITED STATES Tested Age Grade: OVER 8 YEARS OF AGE Assortment No.: N/A Li & Fung Contact: N/A Department No.: 101 Type of Submission: VENDOR SUBMITTED Grouping Test: YES

EXECUTIVE SUMMARY:

The sample(s) DOES NOT MEET the following requirement(s):

- The requirements of test protocol CBRL-8000-US, Toys (V72)

The mechanical hazards requirements of ASTM F963-11, “Standard consumer safety specification for toysafety”.

• The packaging film requirement of ASTM F963-11, "Standard consumer safety specification for toy safety",Section 4.12. Average thickness shall be at least 0,00150 inch.

o The measured average thickness of the packaging film was 0.00136 inch.

The sample(s) MEETS the following requirement(s):

- The requirements of test protocol CBRL-8444-US, CPSIA Requirements Supplement (V22)

Note: According to Note 3 of ASTM F963-11, “Standard consumer safety specification on toy safety”, toys intended for children over the age of six years and their parts are not subject to heavy metals content in substrate requirement of ASTM F963-11 Section 4.3.5.2(2)(b). Therefore, the samples are exempt from such requirement.

Note: No accessible surface coating was present on the received sample(s). Consequently, the lead content analysis of surface coatings according to modified 16 CFR 1303, “Ban of lead-containing paint and certain consumer products bearing lead-containing paint” (Consumer Products Safety Improvement Act (CPSIA) of 2008), was not conducted.

Note: No accessible surface coating was present on the received sample(s). Consequently, the lead content analysis of surface coatings according to Illinois Lead Poisoning Prevention Act, Public Act 095-1019, was not conducted.

Note: According to the associated documents of Consumer Product Safety Improvement Act (CPSIA) of 2008, exemptions were granted to certain materials or products, such as natural materials / paper and similar materials / CMYK process printing inks / metal & alloys / electronics devices components / ordinary books / dyed & undyed textiles. Therefore, the lead content analysis of paper was not conducted.

Above retesting changes Fail to PASS




Page 5 of 35

Note: No street address for the manufacturer, packer or distributor was provided. Street address is required per FPLA/UPLR, unless it can be found in a local city or telephone directory. The presence of the street address in a local directory has not been verified.

BVCPS Buffalo Contact Information for this Report:

Administrative Questions: Debra Kobler Phone: 716-505-3644 [email protected]

Technical Questions: Mark Belstadt Phone: 716-505-3499 [email protected]


Mark B. Belstadt Product Test Engineer, Toys and Juvenile Products Department

/cq




Page 6 of 35

RESULTS:

TOTAL LEAD CONTENT IN SUBSTRATE BY COMPOSITE TESTING (100PPM) (Consumer Product Safety Improvement Act (CPSIA) of 2008) Test Method: U.S. CPSC-CH-E1001-08.1 (June 21, 2010) or U.S. CPSC-CH-E1002-08.1 (June 21, 2010).

Analyte Lead Requirement: Maximum allowable limit: 100 mg/kg

Analyte Lead (Pb) Sample Description Result Conclusion

Color / Component Location Style (mg/kg) (A) Clear soft plastic Decals - LT 10.0 Pass

(B) White foam Plane - LT 10.0 Pass

LT = Less Than mg/kg = milligrams per kilogram (ppm = parts per million) * = Average of duplicate analyses

PHTHALATES CONTENT IN CHILDREN’S TOYS AND CHILDCARE ARTICLES BY COMPOSITE TESTING (Consumer Product Safety Improvement Act (CPSIA) of 2008 Sec. 108(a) Prohibition On Sale of Certain Products Containing Specified Phthalates - BBP / DBP / DEHP CONTENT) Test Method: With reference to U. S. CPSC-CH-C1001-09.3 (April 1, 2010).

Sample Identity

Color / Component Location Style

A White foam Airplane -

B Clear thin plastic backed all color print/adhesive Stickers -

Analyte: BBP DBP DEHP Limit (%): 0.1 0.1 0.1

Analyte BBP DBP DEHP Conclusion Sample Result (%)

A LT 0.005 LT 0.005 LT 0.005 Pass

B LT 0.005 LT 0.005 LT 0.005 Pass

Detection Limit : BBP = Butyl benzyl phthalate (0.005%) Results reported in percentage DBP = Dibutyl phthalate (0.005%) LT = Less than DEHP = Di(2-ethylhexyl) phthalate (0.005%) ND = None detected


Page 7 of 35

PHTHALATES CONTENT IN CHILDREN’S TOYS AND CHILDCARE ARTICLES BY COMPOSITE TESTING (Consumer Product Safety Improvement Act (CPSIA) of 2008 Sec. 108(b)(1) Prohibition On Sale of Certain Products Containing Specified Phthalates - DNOP / DINP / DIDP CONTENT)

Test Method: With reference to U. S. CPSC-CH-C1001-09.3 (April 1, 2010).

Sample Identity

Color / Component Location Style

A White foam Airplane -

B Clear thin plastic backed all color print/adhesive Stickers -

Analyte: DNOP DINP DIDP Limit (%): 0.1 0.1 0.1

Analyte DNOP DINP DIDP Conclusion Sample Result (%)

A LT 0.005 LT 0.005 LT 0.005 Pass

B LT 0.005 LT 0.005 LT 0.005 Pass

Detection Limit : DNOP = Di-n-octyl phthalate (0.005%) Results reported in percentage DINP = Di-iso-nonyl phthalate (0.005%) LT = Less than DIDP = Di-iso-decyl phthalate (0.005%) ND = None detected

CLIENT’S DnHP PHTHALATE CONTENT REQUIREMENT

Test Parameter: DnHP

Limit (%): 0.1 Color / Component Location Style Result (%) Conclusion

A. White foam Airplane - LT 0.005 Pass B. Clear thin plastic backed all color

print/adhesive Stickers - LT 0.005 Pass

Detection Limit : Results reported in percentage DnHP = Dihexyl phthalate (0.005%) LT = Less than

ND = None detected


Page 8 of 35

TOYS (V72)


SCOPE Toy is defined as any object designed, manufactured, or marketed as a plaything for children under 14 years of age. Game consoles and it's associated accessories are defined as General Use Product unless it is embellished or decorated with childish themes or are marketed to children as per Interpretation of "Children's Product" - 16 CFR Part 1200 and will not be covered under this protocol. Novelty toys for candies filled shall test to CBRL-8031-US Protocol.

-

SUPPLEMENTAL PROTOCOL

* ** Federal Communications Commission (FCC) Part 15Document Management

CPSD-EL-PTCL-04999.9-NA, CPSD-

EL-01096-MTHD

Electronic products shall have complied with FCC regulations appropriate for the country of destination as shown by evaluation to the cited protocol. Products under FCC Verification or Declaration of Conformity must be submitted with complete and correct test reports. Designs claimed to be exempt from FCC equipment authorization due to an un-obvious feature (like electronic frequency), must be submitted with acceptable supporting technical documents.

NA

CPSIA Requirements CBRL-GB-PTCL-08444-US

All samples shall be reviewed against the requirements of CPSIA Requirements supplemental protocol to determine if additional testing or labeling is required.

M

*US - Food contact CPSD-AN-PTCL-06001-US

The sample shall meet requirements of supplemental Protocol CPSD-AN-PTCL-06001-US Food contact NA

*California Proposition 65 CBRL-AN-PTCL-06572-US

The sample should be reviewed against the requirements of California Proposition 65 to determine if additional testing or labeling is required.

For samples that fall under the scope of CAProp 65 requirements with testing limit(s) but does not contain appropriate labeling (refer to labeling section for detail), actual testing will be conducted. Otherwise, actual testing is not required and report as "Pass" if the sample contains appropriate labeling.

NA


Packaging and Labeling Evaluation-

UPLR/FPLA NIST handbook 130 part IV A Section 3, 5

& 6 16 CFR 500.4 / 16 CFR 500.5 /

16 CFR 500

• Shall be labeled with product identification. • Shall be labeled with the manufacturer, packer, or distributor’s name and address (city, state and ZIP). • Net quantity of contents shall be on PDP and be expressed in terms of weight or mass, measure, numerical count,

or combination so as to give accurate information to facilitate consumer comparison (English and metric units). • Glue and Adhesives sold with the product shall comply with the labeling requirements of 16 CFR 500, "Regulations

under section 4 of the Fair Packaging and Labeling Act"

Note: evaluate only when packaging is submitted with sample. If no packaging submitted, report as "Not Tested"

M PRODUCT ID: FLYING

EAGLE FOAM SEAPLANE MANUFACTURER: PAUL

K. GUILLOW INC., WAKEFIELD, MA 01880

NET QUANTITY: 1 PLANE, VISIBLE

THROUGH PACKAGING Instructions Visual Shall be legible and easy to understand; instructions shall be consistent with sample performance M


Page 9 of 35

TOYS (V72)


Country of origin marking Country of Origin 19 CFR 134.11

Shall be marked with the country of origin when imported into the U.S. in a conspicuous place to indicate to the ultimate purchaser in the U.S., the English name of the country of origin. • All individually packaged items shall contain the country of origin • All items shipped in bulk or displayed in bulk must contain the country of origin

M Plane – USA

Stickers - China

Age grading CPSC Age Determination Guidelines /

16 CFR Part 1200

All products shall be tested according to either the appropriate age grade, as determined by BVCPS, or the labeled age grade if it is more stringent. In the event the sample is not age labeled, BVCPS will determine the appropriate age grade and test accordingly

Label Age Grade: AGES 8+

Tested Age Grade: OVER 8 YEARS OF AGE

Appropriate Age Grade: OVER 8 YEARS OF AGE

Stuffed Toy Labeling PA / MA / OH Stuffed Toy Law

Stuffed toys shall have a tab or label securely affixed which contains: • A statement that “All New Material” was used • Type of material• The assigned state registration number (Pennsylvania at a minimum)• The name and principal place of business (city and state) of the manufacturer or vendor

NA

Technical Report: (5116)055-0119March 2, 2016 Page 10 of 35

TOYS (V72)


Labeling review – toys ASTM F963-11 sections 4 to 7

Shall have special labeling for specific features such as but not limited to: • Aquatic Toys• Crib And Playpen Toys• Mobiles • Strollers And Carriages • Toys Intended To Be Assembled By An Adult • Simulated Protective Devices • Toys With Functional Sharp Edges And Sharp Points• Small Objects, Small Balls, Marbles and Balloons • Toy Caps• Art Materials • Electric Toys• Battery-Operated Toys • Battery-Powered Ride On Toys• Toys In Contact With Food• Magnets

Packaging, literature accompanying toys, and point-of-sale presentations shall not use words, statements, or graphic material that are inconsistent in any way with the safety labeling instructions for use assembly or age grading of the toy. Information and instructions provided for the safe use or assembly of a toy shall be easy to read and understand by persons of the age level for whom the toy is intended. Shall be in the English language at a minimum. Either a principal component of a toy or the packaging of a toy shall be marked with the name and address of the producer or the distributor.

M

16 CFR 1500.130 Pressurized container labeling

16 CFR 1500.130 Self-pressurized containers shall conform to the labeling requirements as defined by 16 CFR 1500.130 NA

Bedding And Upholstered Furniture Labeling

Association of Bedding and Furniture

All filling materials shall have a securely affixed tag or label which contains the following information: • The statement, “UNDER PENALTY OF LAW THIS TAG NOT TO BE REMOVED EXCEPT BY THE CONSUMER” • A description of the filling contents preceded by the statement, “ALL NEW MATERIALS CONSISTING OF”• The assigned state number (i.e. REG. NO. PA”) • The statements, “Certification is made by the manufacturer that the materials in this article are described in

accordance with law”.

NA


TOYS (V72)


Toy Gun Marking 15 CFR 1150 / ASTM F963-11 section 4.30

Sample shall comply with the requirements as defined in 15 CFR 1150 NA

16 CFR 303 Textile labeling 16 CFR 303 Shall have a label securely affixed that contains: • The name and manufacturer or other marketing or registration number• The country of origin • The generic name and percentage of all fibers in the product

NA

16 CFR 423 Care labeling review 16 CFR 423 Shall have a label securely affixed that contains regular care (customary and routine) information. NA

16 CFR 1500.83(a)(23) Chemistry set labeling

16 CFR 1500.83(a)(23)

Chemistry sets, science education sets and replacement chemicals for such sets, are exempt from section 2(p)(1) of the Federal Hazardous Substances Act if (i) the immediate container of hazardous chemical bears on its main panel the name, appropriate signal word, and

additional statement “Read back (or side) panel before using” and bears on the back (or side) panel the remainderof the appropriate cautionary statement;

(ii) the experiment manual or other instruction book or booklet bears the following caution statement within the borders of a rectangle and in the type size specified in 1500.121: WARNING - This set contains chemicals that may be harmful if misused. Read cautions on individual containers carefully. Not to be used by children except under adult supervision.

(iii) the outer carton bears on the main panel the caution statement specified in (ii).

NA

Labeling of hazardous substances 16 CFR 1500.3(b)(14)(i) / 16

CFR 1500.14(b)(1-5) / 16 CFR 1500.121 /

CPSD-GB-08615.01-MTHD

Applicable to toxic, skin irritant, eye irritant, corrosive, strong sensitizer, extremely flammable, flammable, combustible and hazardous substance requiring special labeling according to 16 CFR 1500.14 (b)(1-5).

Product containing hazardous substances shall conform to and be consistent with the labeling requirements as defined by 16 CFR 1500.3(b)(14)(i) and special labeling requirement according to 16 CFR 1500.14 (b)(1-5).

Note: Only labeling review of defined "signal words", "statement(s)" and "principal hazards(s)" are conducted. Other materials, i.e. generic chemical name, precautionary measures, first -aid, instructions are reported as data only. Information not on PDP is not evaluated. The act also provides exemptions for the labeling of hazardous substance according to 16 CFR 1500.83, which is not included in the evaluation of labeling of hazardous substances.

NA

21 CFR 101 Food labeling

21 CFR 170-189 Food ingredient list review

21 CFR 101

21 CFR 73, 74, 82 and 170 through 189

Food and Nutritional labeling shall be evaluated in accordance with the required size, format, contents, etc. as defined by the regulation. (Vendor shall be responsible for the accuracy of information contained) Additives and colors contained in the ingredients list shall be evaluated in accordance with the approved list of ingredients as defined by the regulation. (Vendor shall be responsible for the accuracy of information contained)

NA

FDA cosmetic labeling review ASTM F963-11 section 4.3.4 / 21 CFR 701 and 740

Cosmetics labeling shall be evaluated in accordance with the required size, format, contents, etc. as defined by the regulation.


NA


TOYS (V72)


FDA ingredient list evaluation ASTM F963-11 section 4.3.4 / 21

CFR 73, 74, 82, 700 and 701

Ingredient and colors contained in the ingredients list shall be evaluated in accordance with the approved list of ingredients as defined by the regulation.


NA

Illinois lead warning label Illinois Lead Poisoning Prevention

Act

Product shall not contain the following Illinois lead warning label per client's requirement. Refer to the analytical section for details.

"WARNING: CONTAINS LEAD. MAY BE HARMFUL IF EATEN OR CHEWED. COMPLIES WITH FEDERAL STANDARDS."

M

Phthalates-Free Claim CPSD-HL-01057-MTHD

The product and/or packaging shall not contain a "Phthalates free" or equivalent claim. NA

SAFETY REQUIREMENTS

Mechanical hazards - toys ASTM F963-11 section 4

Shall meet the requirements specified in the standard. NM Packaging Film Average thickness was less than

0.00150 in. at

Side A 0.00136 in. Side B 0.00146 in.

Mechanical hazards - lawn darts 16 CFR 1500.18(a)(4) Lawn darts and other similar sharp-pointed toys usually intended for outdoor use and having the potential for causing puncture wound injury. The supply of these goods is banned.

NA

Mechanical hazards - clacker ball 16 CFR 1500.18(a)(7) Shall comply with the requirements specified in 16 CFR 1500.86(a)(5). NA

Rattles 16 CFR 1510 / ASTM F963-11 section 4.23

Rattles shall meet the safety requirements as specified in 16 CFR 1510 NA

Pacifiers 16 CFR 1511 / ASTM F963-11 section 4.20

Samples shall meet the safety requirements as specified in 16 CFR 1511 if nipple length longer than 0.63 inch NA

16 CFR 1500 Dive stick 16 CFR 1500 Samples shall meet the safety requirements as specified in 16 CFR 1500 NA

21 CFR 801.410 FDA Lens impact - doc review

21 CFR 801.410(c) Shall be fitted with impact-resistant lenses to protect the consumer from potential eye injuries. Lenses shall meet an AQL of 6.5 as specified in 21 CFR 801.410 when subjected to FDA using MIL-STD 105E or FDA approved statistical sampling plan. In lieu of testing, test report can be submitted if dated within one year. It is the vendor's responsibility to assure the manufacturer is registered under the FDA. NOTE: The documentation requirements of 21 CFR 801.410 (f) are the responsibility of the manufacturer.

NA


TOYS (V72)


NY Restriction of sale of Yo-Yo Waterball

Section 399 General Business Law/

A472

No person, firm, corporation, or association shall import, manufacture, sell, offer to sell, or distribute a Yo-Yo waterball toys.

"Yo-Yo waterball toy" means a yo-yo waterball, water yo-yo, or any similar toy made of rubber or rubberlike material consisting of a ball that is filled with a liquid and attached to an elastic cord with a finger loop at the end.

NA

Flammability of solids 16 CFR 1500.44 / 16 CFR 1500.3(c)(6)(vi) /

ASTM F963-11 section 4.2 Annex A5

Shall not exceed the maximum allowable limit of no greater than 0.1 inches per second M

Flash point of combustible liquid 16 CFR 1500.3(c)(6)(iii) /

16CFR 1500.43(a) CPSD-GB-00019-

MTHD

All liquid items for children aged 8 years and under shall have flash point greater than 150 °F or 65.6 °C.

Remark: - For products intended for children aged over 8 years, if the liquid items are classified as either combustible, flammableor extremely flammable, it shall conform to the labeling of hazardous substances. - Liquid is defined as any material which is free flowing, has no fixed shape and would take the shape of its container.

NA

Flammability of self-pressurized containers

16 CFR 1500.3(c)(6)(viii) / 16

CFR 1500.45

Self-pressurized container for children aged 8 years and under shall not be flammable when tested in according to 16 CFR 1500.45.

Remark: For products intended for children aged over 8 years, if the contents of the self-pressurized containers are classified as either flammable or extremely flammable, it shall conform to the labeling of hazardous substances.

NA

Flammability of clothing textiles 16 CFR 1610 / ASTM F963-11 section 4.2 /

Annex A6

Textile fabrics used in toys should comply with 16 CFR 1610 as applicable NA

16 CFR 1610 Flammability (costume)

16 CFR 1610 Costumes should comply with 16 CFR 1610 as applicable NA

16 CFR 1611 Flammability (vinyl plastic film)

16 CFR 1611 Textile fabrics used in toys should comply with 16 CFR 1611 as applicable NA

CPAI-75 Flammability (sleeping bags) - doc review

CPAI-75 Materials shall comply with the requirements as defined. In lieu of testing, test report can be submitted if dated within one year.

NA

CPAI-84 Flammability (camping tentage) - doc

CPAI-84 Materials shall comply with the requirements as defined. In lieu of testing, test report can be submitted if dated within one year.

NA


TOYS (V72)


Drawstrings / Ties on children upper outerwear

16 CFR 1120 / Visual or Actual

Measurement

Hood and Neck Area On Upper Outerwear (Sizes 2T-12) Hood and neck drawstrings/ties are not allowed at all on any children’s upper outerwear (outerwear including jackets and sweatshirts).

Waist and Bottom Area On Upper Outerwear Garments (Sizes 2T-16) Drawstrings/ties may not exceed 3 inches (75mm) in length on each side outside the drawstring channel when garment is expanded to its fullest width. Drawstrings/ties must be bartacked at center back so string cannot be pulled out. No toggles, knots or attachment at the free ends. Must be finished at both ends.

Note For S, M, L, XL sizing Girls and Boys size (L) is equivalent to size 12 and Girls and Boys size (XL) is equivalent to size 16.

NA

Drawstrings New York State Law 391.b and

amendment and Wisconsin State Law ATCP 139 / Visual or Actual Measurement

(Sizes 0-16) Hood and Neck Area Hood and neck drawstrings are not allowed at all on any children’s clothing (outerwear and non-outwear).

Waist On Upper Garments (tops, jackets, dresses) and Bottoms (pants, shorts, skirts) May not exceed 3 inches (75mm) in length on each side outside the drawstring channel when garment is expanded to its fullest width. Drawstrings must be bartacked at center back so string cannot be pulled out. No toggles, knots or attachment at the free ends. Must be finished at both ends.

NA

Total lead content in surface coatings

Illinois Lead Poisoning

Prevention Act / CPSC-CH-E1003-09.1 / CPSD-AN-

00001-MTHD

The following surface coatings shall contain less than 0.004% (40ppm) lead or lead compounds in which the lead content is the weight of the total content: a. All accessible surface coatings, in the as received state, on jewelry for children under 12 years of age, b. All accessible surface coatings, before and after use and abuse testing, on child care articles for children 6 years of

age or younger, and on toys for children under 12 years of age. As a client requirement, the warning label is not allowed.

In case of insufficient coating for testing found on the number of samples specified in the protocol, vendor needs to provide additional samples/component parts (including raw materials) for testing. The vendor is responsible for compliance of all other products outside of the above scope.


NA


TOYS (V72)


Total lead content in substrate materials

Illinois Lead Poisoning

Prevention Act / CPSC-CH-E1001-08.3 / CPSC-CH-

E1002-08.3/ CPSD-AN-00185-MTHD / CPSD-AN-00196-

MTHD

The following substrate materials shall contain less than 0.004% (40ppm) lead or lead compounds in which the lead content is the weight of the total content: a. All accessible substrate materials, in the as received state, on jewelry for children under 12 years of age,b. All accessible substrate materials, before and after use and abuse testing, on child care articles for children 6 years

of age or younger.As a client requirement, the warning label is not allowed.

In case of insufficient material for testing found on the number of samples specified in the protocol, vendor needs to provide additional samples/components/parts for testing. Materials exempted from testing under CPSIA (e.g., textiles) under 16 CFR 1500.88 and 1500.91 (d) and (e) will not be tested. The vendor is responsible for compliance of all other products outside of the above scope.


NA

Total cadmium content in surface coatings

AOAC 974.02:2005 modified / acid digestion, ICP

analysis

All accessible surface coatings , before and after use and abuse testing, on jewelry intended for children ages 12 and under shall not contain cadmium in excess of 0.004% (40ppm) of the weight of the total content.



NA

Total cadmium content in substrate materials

CPSC-CH-E1002-08

(modified) / CPSC-CH-E1001-08

(modified) / acid digestion, ICP

analysis

All accessible plastic and metal substrate materials, before and after use and abuse testing, of jewelry intended for children ages 12 and under shall not contain cadmium in excess of 0.004% (40ppm) of the weight of the total content.



NA


TOYS (V72)


Total heavy metal contents in surface coatings

ASTM F963-11 section 4.3.5.1 (2)

and 8.3.1 / CPSC-CH-E1003-09 / CPSD-AN-00564-MTHD

All accessible surface coating, before and after use and abuse testing, shall not contain compounds of which the metal content of the total content exceeds the levels by weight (mg/kg) of the contained solid including pigments, film solids and driers [Antimony (Sb) 60, Arsenic (As) 25, Barium (Ba) 1000, Cadmium (Cd) 75, Chromium (Cr) 60, Lead (Pb) 90, Mercury (Hg) 60, Selenium (Se) 500]


NA

Soluble heavy metal contents in surface coatings

ASTM F963-11 section 4.3.5.1 (2)

and 8.3.2 / CPSD-AN-00564-MTHD

All accessible surface coating, before and after use and abuse testing, shall not contain compounds of which the metal content of the soluble material exceeds the levels by weight (mg/kg) of the contained solid including pigments, film solids and driers [Antimony (Sb) 60, Arsenic (As) 25, Barium (Ba) 1000, Cadmium (Cd) 75, Chromium (Cr) 60, Lead (Pb) 90, Mercury (Hg) 60, Selenium (Se) 500]

Coating materials that contain less than the total limit of [Antimony (Sb) 60, Arsenic (As) 25, Barium (Ba) 1000, Cadmium (Cd) 75, Chromium (Cr) 60, Lead (Pb) 90, Mercury (Hg) 60, Selenium (Se) 500] do not need to be tested for the soluble content.


NA


TOYS (V72)


Total heavy metal contents in substrate

ASTM F963-11 section 4.3.5.2 (2) (b) and 8.3.1 / 16 CFR 1251 / CPSC-CH-

E1001-08.1 / CPSC-CH-E1002-08.1 / CPSD-AN-00564-

MTHD

All accessible substrates, before and after use and abuse testing, shall have total heavy metals content comply with the limits specified in Table 1 of the standard. [Antimony (Sb) 60 mg/kg, Arsenic (As) 25 mg/kg, Barium (Ba) 1000 mg/kg, Cadmium (Cd) 75 mg/kg, Chromium (Cr) 60 mg/kg, Lead (Pb) 90 mg/kg, Mercury (Hg) 60 mg/kg, Selenium (Se) 500 mg/kg]

Report actual results or include data table within report. If all heavy metal limits except for lead are met then no soluble lead testing will be conducted when the CPSIA total lead requirement is not met. Conduct soluble heavy metal test directly if there is only one textile component in the product.

Component testing is allowed. Based on the standard, will composite up to 3 like materials. If any material in the composite exceeds 80% of the limit of any heavy metal except for lead based on the lowest weight component then soluble heavy metal content test with individual material will be analyzed. Unfinished and untreated wood as defined in 16 CFR 1251 will not be tested.

NA

Soluble heavy metal contents in substrate

ASTM F963-11 section 4.3.5.2 (2) (b) and 8.3.5 / 16 CFR 1251 / CPSD-AN-

00564-MTHD

All accessible substrates, before and after use and abuse testing, shall have soluble heavy metals content comply with the limits specified in Table 1 of the standard. [Antimony (Sb) 60 mg/kg, Arsenic (As) 25 mg/kg, Barium (Ba) 1000 mg/kg, Cadmium (Cd) 75 mg/kg, Chromium (Cr) 60 mg/kg, Lead (Pb) 90 mg/kg, Mercury (Hg) 60 mg/kg, Selenium (Se) 500 mg/kg]

Substrates that contain less than the total limit of [Antimony (Sb) 60 mg/kg, Arsenic (As) 25 mg/kg, Barium (Ba) 1000 mg/kg, Cadmium (Cd) 75 mg/kg, Chromium (Cr) 60 mg/kg, Lead (Pb) 90 mg/kg, Mercury (Hg) 60 mg/kg, Selenium (Se) 500 mg/kg] do not need to be tested for the soluble content.

Report actual results or include data table within report. Component testing is allowed. Compositing is not allowed. Unfinished and untreated wood as defined in 16 CFR 1251 will not be tested.

NA


TOYS (V72)


Total heavy metals contents in modeling clay

ASTM F963-11 section 4.3.5.2 (2) (b) and 8.3.1 / CPSC-CH-E1002-08.1 / CPSD-

AN-00564-MTHD

Modeling clay included as part of a toy shall have total heavy metals content comply with the limits specified in Table 2 of the standard. [Antimony (Sb) 60 mg/kg, Arsenic (As) 25 mg/kg, Barium (Ba) 250 mg/kg, Cadmium (Cd) 50 mg/kg, Chromium (Cr) 25 mg/kg, Lead (Pb) 90 mg/kg, Mercury (Hg) 25 mg/kg, Selenium (Se) 500 mg/kg]


NA

Soluble heavy metals contents in modeling clay

ASTM F963-11 section 4.3.5.2 (2) (b) and 8.3.5 / CPSD-AN-

00564-MTHD

Modeling clay included as part of a toy shall have soluble heavy metals content comply with the limits specified in Table 2 of the standard. [Antimony (Sb) 60 mg/kg, Arsenic (As) 25 mg/kg, Barium (Ba) 250 mg/kg, Cadmium (Cd) 50 mg/kg, Chromium (Cr) 25 mg/kg, Lead (Pb) 90 mg/kg, Mercury (Hg) 25 mg/kg, Selenium (Se) 500 mg/kg]

Modeling clay that contain less than the total limit of [Antimony (Sb) 60, Arsenic (As) 25, Barium (Ba) 250, Cadmium (Cd) 50, Chromium (Cr) 25, Lead (Pb) 90, Mercury (Hg) 25, Selenium (Se) 500] do not need to be tested for the soluble content.


NA

Extractable cadmium content in metal

ASTM F963-11 section 4.3.5.2 (2) (c)

and 8.3.5.5 (3) / CPSC-CH-E1004-11 /

CPSD-AN-00564-MTHD

All accessible metal component of toy, that is a small part, before and after use and abuse testing, shall not contain more than 200 micrograms of cadmium per component.

Metal that contain less than 75 ppm total cadmium do not need to be tested for the extractable content.


NA

Total cadmium content in metal ASTM F963-11, section 4.3.5.2 (2) (c) / CPSC-CH-E1001-08.1 / CPSD-AN-

00564-MTHD

All accessible metal component of toy, that is a small part, before and after use and abuse testing, shall not contain cadmium in excess of 0.0075% (75ppm) of the weight of the total content (which is a screening limit).


NA


TOYS (V72)


21 CFR 700.13 Mercury in cosmetics

21 CFR 700.13 Shall not contain more than 0.0065% of mercury for cosmetics intended for use with the eyes and 0.0001% of mercury for other cosmetics.

NA

*Total mercury content in batteries Mercury-Containing and Rechargeable

Battery Management Act U.S. Pub. L. 104-142 Title II / CPSD-AN-00078-MTHD

Batteries shall comply with one of the following requirements:

(i) Alkaline-manganese button cell shall contain less than 25 mg Hg / cell. (ii) Alkaline-manganese battery and Zinc carbon battery shall contain no intentionally added mercury (BV reporting limitis 4 mg/kg). (iii) No Mercuric-oxide button cell or battery is allowed.

Actual testing would be conducted on button cell batteries. It is the vendor’s responsibility for the conformity to this requirement for other batteries.

NA

*Total mercury content in button cell batteries

Various US State Laws / CPSD-AN-

00078-MTHD

Button cell battery shall not contain any detectable levels of mercury (BV reporting limit is 4 mg/kg). NA

GRAS – FDA Stainless Steel Guidelines – Documentation Review

FDA Generally Recognized as Safe (GRAS) Guidelines

Shall meet FDA GRAS Guidelines. Documentation shall be provided. If no documentation is provided, testing will be conducted.

In lieu of testing, document may be submitted if dated within One year

NA

*Transmittance properties forsunglasses and eyewears

ANSI Z80.3-2010 clause 4.6.1 to 4.6.3, 4.6.5, 4.7.3 to 4.7.4 and 4.8 / CPSD-AN-

00102-MTHD

Non-prescription sunglasses and fashion eyewear shall comply with the requirements. Sunglasses containing a UVA/UVB protection, Traffic signal recognition and/or other ANSI Z80.3 claim will be tested to substantiate such claims.

NA

CONEG - doc review CONEG This environmentally motivated legislation regulates the amount of lead, cadmium, hexavalent chromium and mercury allowed in packaging materials. It is the vendor’s responsibility for the conformity of this requirement.

NR

*Pyrotechnic Composition 16 CFR 1507.11 Modified

Party poppers (also known as champagne party poppers and party surprise poppers) and Christmas crackers shall contain no more than 0.25 grains (16.2 mg) of pyrotechnic material.

Modification: expand the scope to include Christmas crackers

NA

LHAMA evaluation in art materials - document review

16 CFR 1500.14(b)(8) /

ASTM D4236-94 (R 2011) / CPSD-GB-

00001-MTHD

Art materials intended for use by children, including toys and parts of toys, shall not pose any chronic health hazards. Toxicity Risk Assessment shall be conducted.


NA


TOYS (V72)


Toxicological risk assessment - document review

ASTM F963-11 section 4.3.1 and 8.2 / 16 CFR 1500.3 (b)(5) and 1500.3 (b)(7)-(9) /

CPSD-GB-00001-MTHD

Products intended for use by children, including toys and parts of toys, must not be toxic a skin irritant, eye irritant, corrosive, or a strong sensitizer.

Toxicological Risk Assessment shall be conducted to substantiate the compliance of the regulation for the following components: - The following high risk materials: All toy cosmetics, liquids, pastes, putties, gels and powders regardless of claim - Other materials bearing a "NON-TOXIC" claim on samples and/or its packaging


NA

Hazardous substances in liquid – document review

16 CFR 1500.14(a)(1-5) / CPSD-GB-00001-

MTHD

To identify the presence of potentially hazardous ingredients, all liquid components and liquid-filled items designed or intended to be used by individuals over 8 years old containing substances exceeding the following limits require special labeling:

a. 10% or more by weight of ethylene glycol b. 10% or more by weight of diethylene glycol c. 4% or more by weight of methanold. 10% or more by weight of petroleum distillates e. 5% or more by weight of benzenef. 10% or more by weight of turpentine g. 10% or more by weight of tolueneh. 10% or more by weight of xylene

Note: - Liquid is defined as any material which is free flowing, has no fixed shape and would take the shape of its container.


NA


TOYS (V72)


Hazardous liquids – document review

16 CFR 1500.231 / CPSD-GB-00001-

MTHD

To identify the presence of potentially hazardous ingredients, all liquid components and liquid-filled items intended or likely to be used by children aged 8 years and under shall comply with this requirement and the following chemicals shall not be present:

a. Ethylene glycolb. Diethylene glycolc. Methanold. Mercury e. Methylene chloridef. Petroleum distillatesg. Tolueneh. Xylenei. Benzenej. Turpentine

Note: - Liquid is defined as any material which is free flowing, has no fixed shape and would take the shape of its container. - This includes liquids that are sealed in a product and BV expands to un-sealed liquid (16 CFR 1500.14).


NA

DEHP Content ASTM F963-11 section 4.3.8 / ASTM D3421:75 / CPSD-AN-00096-MTHD

Pacifiers, rattles, and teethers shall not intentionally contain Di (2-ethylhexyl) phthalate. Shall not contain more than 3% of total solid.

NA

Nitrosamines content in rubber pacifiers - document review

ASTM F963-11 section 4.20.1 / ASTM

F1313-90(R2011) / CPSD-GB-00001-

MTHD

Rubber nipple on pacifier shall comply with following requirements:



NA

*Nitrosamines in rubber pacifier ASTM F963-11 section 4.20.1 / ASTM

F1313-90(R2011)

Rubber nipples on pacifiers shall comply with following requirements:


NA


TOYS (V72)


PA stuffed toy law tolerance - document review

ASTM F963-11 section 4.3.7

Loose fillers shall be visually evaluated for objectionable matter and labels shall be evaluated accordingly.

Shall meet the requirements of the “Tolerances of the Commonwealth of Pennsylvania Regulation for Stuffed Toys”. In lieu of testing, test report can be submitted if dated within one year.

NA

Total plate count and total coliform

ASTM F963-11 section 4.3.6.1 / Bacteriological

Analytical Manual (BAM) / CPSD-AN-00034, 35-MTHD

Pure water used in filling of toys shall meet the requirements of < 100 CFU/ml of total plate count and < 1 CFU/100ml of total Coliform.

NA

Microbial limit test - document review

ASTM F963-11 section 4.3.6.3 and

8.4.1 / USP 31<61> / CPSD-GB-00001-

MTHD

Cosmetics, liquids, pastes, putties, gels and powders used in toys (excluding art materials) shall not be contaminated with Salmonella, E. Coli, Pseudomonas aeruginosa, or Staphylococcus aureus and be subject to requirements of less than or equal to 5,000 CFU/ml (less than or equal to 500 CFU/ml for cosmetics intended for use with the eyes and baby products) for total viable count (total plate count + yeast & mold count) as intended to minimize risk associated with lack of cleanliness, shelf life and contamination.


Note: In order to ensure the integrity of the received test report, actual testing on total plate count would be conducted (Refer to Total plate count test line for detail.).

NA

Total plate count USP 31 <61> / CPSD-AN-00035-

MTHD

Cosmetics, liquids, pastes, putties, gels and powders shall have total plate count less than or equal to 5,000 CFU/ml (less than or equal to 500 CFU/ml for cosmetics intended for use with the eyes and baby products).

Client requirement

NA

Preservative effectiveness - document review

ASTM F963-11 section 4.3.6.3 and

8.4.2 / USP 35<51> / CPSD-GB-00001-

MTHD

Formulations used to prevent microbial degradation in cosmetics, liquids, pastes, putties, gels and powders used in toys (excluding art materials) shall be tested for microbial control and preservative effectiveness.

In lieu of testing, test report can be submitted if dated within two years.

NA

Battery-powered ride-on toys ASTM F963-11 section 4.25.10

Samples shall meet the safety requirement as specified in ASTM F963-11, section 4.25.10 NA

Electrically operated toys 16 CFR 1505 / ASTM F963-11 section 4.4

Toys operating from nominal 120-V branch circuits shall conform to the requirements of 16 CFR 1505 NA

UL Testing (For electrically operated product)

UL Standard Item will be audited to verify compliance with the selected sections of the applicable and/or labeled UL standard. NA

Safety Agency Listing Verification E – 1090 Verify Client Acceptable Safety Agency Listing by contacting Listing Agency with the sample's Listing Number, Manufacturer, Model Number, and/or Agency Control Number. Shall be verified.

NA


TOYS (V72)


AATCC 20A Quantitative 16 CFR 303 Shall be tested to substantiate fiber content. Shall not exceed a deviation of + 3% from the label as allowed for blends and no deviation for items labeled 100% of a fiber.

NA

Wearing Apparel – Care Label 16 CFR 423 For wearing apparel covered by 16 CFR 423: With care label: Conduct laundry test according to the labeled care instruction. Evaluate for general appearance as acceptance criteria. Without care label: Failed for labeling requirement. No softline test will be conducted.

For wearing apparel not covered by 16 CFR 423: With care label: Conduct laundry test according to the labeled care instruction. Evaluate for general appearance as acceptance criteria. Without care label: No softline test is required.

NA

BBP / DBP / DEHP content

DnOP / DINP / DIDP content

DnHP content

CPSD-AN-00095-MTHD /

CPSD-AN-00143-MTHD

The following products outside of the scope of CPSIA, in the as received state, shall not contain concentrations of more than 0.1% BBP, DBP DEHP, DINP, DIDP, DnOP, DnHP individually: Report actual results or include data table within report.

Component testing is allowed. Actual testing would be conducted on accessible high risk (listed below) plastics materials. a. Poly vinyl chloride (PVC) b. Poly vinylidene chloride (PVDC) c. Poly vinyl acetate (PVAc) d. Poly urethane (PU)e. Ethylene propylene diene monomer rubber (EPDM) f. Ethylene vinyl acetate (EVA)g. Other foam plastics (except polyolefins)h. Natural and synthetic rubberi. Siliconej. Thermoplastic elastomers (TPEs) k. Plastic materials other than polyolefins with shore A hardness < 90Composite up to 3 like materials. The composite result (based on material weight) will be evaluated against the adjusted limit (regulatory limit divided by the number of components in the composite). If composite fails and ON REQUEST, individual components will be analyzed.Client Requirement

NA


TOYS (V72)


*Bisphenol A content Various state laws (e.g. CT Public Act #

09-103 and MN Chapter 40 SF #247) /

21 CFR 177.1580 / CPSD-AN-00169-

MTHD

The following products shall not contain any detectable levels of Bisphenol-A (BPA) (BV reporting limit is 0.1mg/kg): - Infant formula/ baby food plastic container, jar or can - All reusable food or beverage containers including lids (if any)- Baby bottle liners - Pacifiers - Straws

"Infant formula" means a commercially available milk based or soy based powder, concentrated liquid or ready-to-feed substitute for human breast milk that is intended for infant consumption."Baby food" means a commercially available prepared solid food consisting of a soft paste or an easily chewed food that is intended for consumption by children two years of age or younger."Reusable food or beverage container" means a receptacle for storing food or beverages, including, but not limited to, baby bottles, spill-proof cups, sports bottles and thermoses, and excluding containers intended for disposal after initial use.

Report actual results or include data table within report.

Note: - Actual testing will be conducted on all accessible polycarbonate, and epoxy resin materials only, including bothcoatings and substrates- Vendors shall provide documentation or a bill of material for material identification. If they cannot provide surfacecoating material information, all coatings ( except lacquer and paint) will be tested. - Vendors shall be responsible for the compliance of all other materials.- Testing will not be conducted on food contact polycarbonate resins in infant feeding bottles (baby bottles) and spill-proof cups including their closures and lids, designed to help train babies and toddlers to drink from cups (sippy cups), because food contact polycarbonate resin are banned in these products by 21 CFR 177.1580. - Composite all colors of surface coating to perform one test.

NA

WORKMANSHIP AND PERFORMANCE REQUIREMENTS

Function Per instruction or intended use

Shall function as intended M

Air Leakage For Inflatable Pool Items

Per Criteria Inflatable pool items (e.g. inflatable pool, swimming rings, etc.) which are intended to bear the mass of children shall be evaluated for air leakage for duration of one hour.

NA

Dishwasher Claim Verification Per Criteria Items containing a dishwasher safe claim will be subjected to 5 normal cycles and evaluated for any color change, warping, breaking, leaking or other defects.

NA

Microwave Claim Verification Per Criteria Items containing a microwave safe claim will be subjected to 10 normal cycles and evaluated for any color change, warping, breaking, leaking or other defects.

NA


TOYS (V72)


Freezer Claim Verification Per Criteria Items containing a freezer safe claim will be subjected to 3 freeze/thaw cycles and evaluated for any color change, warping, breaking, leaking or other defects.

NA

Battery-operated Items NA




NA

Battery Insertion / Removal CPSD-HL-01058-MTHD / Visual

Insert and remove the batteries 100 cycles, turning the unit on for 10 seconds each cycle.

Shall function as claimed for each cycle.

If failure is noted before 100 cycles, report the number of cycles at failure and the type of failure.

NA

*Extended Performance CPSD-GB-01058-MTHD

Assemble as instructed. Insert the recommended number and type of batteries. This test should be conducted for 8 hours. Operate continuously until the batteries have drained or 8 hours of operation was completed. During and / or at the end of period, check for visual signs of failure, including heat buildup, mechanical problems, etc.

After batteries have drained at the end, wait at least 10 minutes before inserting fresh, new batteries, and resuming the remaining of total 8 hours of operation.

Shall exhibit no failures.

If failure is noted before the end of the 8 hours operation, report duration and the type of failure.



NA


TOYS (V72)


*Battery Compartment Fitment Test CPSD-HL-01058-MTHD /

Actual use

[Only apply to replaceable battery type of battery operated items] [Does not apply to button cell battery powered items]

Use 3 major brands of appropriate size batteries (like Rayovac, Duracell, and Energizer), the battery/batteries shall fit in the compartment and shall be function as intended.

Report battery brands being used for the testing.

Client's requirements: 3 brands of batteries used shall be Duracell, Energizer and Rayovac.

Test also the batteries that come with the product if applicable.

NA

Battery Reverse Voltage Test CPSD-HL-01058-MTHD / Actual use

Reversing battery orientation shall not damage unit. NA

Electrical Plug-in items (not battery operated)

NA




NA

Extended Performance – 48 hours

CPSD-HL-01058-MTHD / Visual

Assemble as instructed. Operate continuously for 8 hour periods for a total of 6 periods. During and / or at the end of each period, check visual signs of failure, including heat buildup, mechanical problems, etc.

Shall exhibit no failures for 48 hours.

If failure is noted before the end of the 48 hours, report duration and the type of failure.



NA



Rating Key: M Meets NM Does Not Meet NA Not Applicable NR Not Requested

Testing Parameter Age (Months) Abuse Test Conditions

Drop Test 0 to ≤18 >18 to ≤36 >36 to ≤96

4.5 ft (1.37 m), 10 drops 3 ft (0.91 m), 4 drops 3 ft (0.91 m), 4 drops

Torque Test 0 to ≤18 >18 to ≤36 >36 to ≤96

2 in - lb (0.23 N - m) 3 in - lb (0.34 N - m) 4 in - lb (0.45 N - m)

Tension Test 0 to ≤18 >18 to ≤36 >36 to ≤96

10 lb (44.5 N)

15 lb (66.8 N) 15 lb (66.8 N)

Compression Test 0 to ≤18 >18 to ≤36 >36 to ≤96

20 lb (89 N) 25 lb (111.3 N) 30 lb (133.5 N)

No. of samples required for complete testing: Toys and Hardgoods (case by case for assortments) 12 Dinnerware, Mugs, Pitchers, etc (decorated lip/rim) 12 (18) Creation Date: MARCH 7, 2006 Product contain Fiber Content 1 additional Editorial Revision Date: DECEMBER 29, 2015 Product contain Care Label Minimum additional 2 pcs and 1 Pricing Review Date MAY 20, 2010

additional pc for each care instruction Technical Review Date MAY 20, 2010 No. of working days for complete testing 5 Revision No: 72


CPSIA REQUIREMENTS SUPPLEMENT (V22) Evaluation Citation/Method Criteria Results Rating SCOPE: This protocol applies to toys, children products and child care article as defined by CPSIA, all furniture, including adult furniture, and household paint.


Tracking labels for children’s products

Consumer Product Safety Improvement

Act of 2008

A permanent and distinguishing mark or code on the product and its packaging, to the extent practicable, allows the manufacturer and purchaser to ascertain the name of the manufacturer or private labeler, location and date of production of the product. Verified the Presence and Report the tracking label information.^ The accuracy of tracking label will not be verified.

Note: - Manufacturer or Private Labeler name can not be coded. RN# can be used for Manufacturer or Private Labelername for softline items as per client’s request. - City information is not mandatory for location as per client’s request - Date of production shall contain month and year- As a client's requirement, tracking label for science kits can be oninstruction sheet or product as well as on packaging.

^ Picture of tracking label shall be included in the test report. When the tracking label in the packaging is different from the product, both tracking label should be pictured and included in test report.

Client’s requirement

M PASS


CPSIA REQUIREMENTS SUPPLEMENT (V22) Evaluation Citation/Method Criteria Results Rating

* Registration for durable nursery product

CPSIA section 104(d) / 16 CFR 1130

Consumer registration requirement: Required to provide consumers with a postage-paid consumer registration form with each such product and to permanently place the manufacturer name and contact information, model name and number, and the date of manufacture on each durable infant or toddler product.

Requirements for registration form: The registration form shall (A) include spaces for a consumer to provide the consumer's name, address, telephone number, and e-mail address; (B) include space sufficiently large to permit easy, legible recording of all desired information; (C) be attached to the surface of each durable infant or toddler product so that, as a practical matter, the consumermust notice and handle the form after purchasing the product; (D) include the manufacturer's name, model name and number for the product, and the date of manufacture; (E) include a message explaining the purpose of the registration and designed to encourage consumers to completethe registration; (F) include an option for consumers to register through the Internet; and(G) include a statement that information provided by the consumer shall not be used for any purpose other than to facilitate a recall of or safety alert regarding that product.

"Durable infant or toddler product" means full-size cribs and nonfull-size cribs, toddler beds, high chairs, booster chairs, hook-on chairs, bath seats, gates and other enclosures for confining a child, play yards, stationary activity centers, infant carriers, strollers, walkers, swings, bassinets and cradles, children's folding chairs, changing tables, bouncers, infant bath tubs, bed rails and infant sling.

NA -


CPSIA REQUIREMENTS SUPPLEMENT (V22) Evaluation Citation/Method Criteria Results Rating ANALYTICAL

*Total lead content in surfacecoatings

Consumer Product Safety Improvement

Act of 2008 / 16 CFR 1303 / AOAC 974.02 (modified) / CPSD-AN-00001-

MTHD / CPSC-CH-E1003-09

All accessible surface coatings, before and after use and abuse testing, on items intended for children ages 12 and under shall not contain lead or lead components in which the lead content is in excess of 0.009% (90 ppm) of the weight of the total content.

For Sample other than Tracking Labels: In case of insufficient coating for testing found on number of samples specified in the protocol, vendor needs to provide additional samples or components/parts for testing.

For Tracking Labels ONLY: In case of insufficient coating for testing found on number of samples specified in the protocol, vendor needs to provide dipped parts or components/parts for testing.

Report actual results or include data table within report. Issue a third party test report.

Component testing is allowed. Wet paint is NOT allowed.Compositing up to 3 is allowed.

NA -

*Total lead content in surfacecoatings

Consumer Product Safety Improvement Act of 2008 / 16 CFR

1303 / AOAC 974.02(mod) / CPSD-

AN-00001-MTHD / CPSC-CH-E1003-09

All accessible surface coatings in the assembled state on adult furniture [exempt factory applied coatings on metal components/parts] and household paint shall not contain lead or lead components in which the lead content is in exceed of 0.009% (90 ppm) of the weight of the total content.

In case of insufficient coating for testing found on number of samples specified in the protocol, vendor needs to provide additional samples, dipped parts or components/parts for testing.

Report actual results or include data table within report Issue a program audit report Component testing is allowed. Wet paint is NOT allowed. Compositing up to 3 is allowed.

NA -


CPSIA REQUIREMENTS SUPPLEMENT (V22) Evaluation Citation/Method Criteria Results Rating

*Total lead content in substratematerials

Consumer Product Safety Improvement Act of 2008 / CPSC-

CH-E1001-08.1 / CPSC-CH-E1002-08.1

/ CPSD-AN-00185-MTHD / CPSD-AN-

00196-MTHD

All accessible substrates, before and after use and abuse testing, on items intended for children ages 12 and under shall not contain lead in excess of 0.01% (100ppm) of the weight of the total content.

In case of insufficient material for testing found on number of samples specified in the protocol, vendor needs to provide components/parts for testing.

Report actual results or include data table within report. Issue a program audit report (until December 2011).

Component testing is allowed. Compositing up to 3 like materials is allowed except metal.

M PASS

*Total lead in children's metal jewelry

Consumer Product Safety Improvement Act of 2008 / CPSC-

CH-E1001-08.1 / CPSD-AN-00185-

MTHD

Any accessible metal component of jewelry intended for children ages 12 and under shall not contain lead in excess of 0.01% (100ppm) of the weight of the total content.

Report actual results or include data table within report

Issue a third party test report Compositing is not allowed Component testing is not allowed

NA -


CPSIA REQUIREMENTS SUPPLEMENT (V22) Evaluation Citation/Method Criteria Results Rating *BBP / DBP / DEHP content

*DnOP / DINP / DIDP content

Consumer Product Safety

Improvement Act of 2008 / CPSC-CH-C1001-09.3

modified / CPSD-AN-00095-MTHD


Actual testing would be conducted on the following accessible plastics materials, plasticizer print, scrapable surface coatings, decals, polymeric coated materials (unscrapable), adhesives and sealants (exclude adhesive for stickers), toy nail polish, reusable packaging, electrical plug and cables.

Vendor shall be responsible for the compliance of all other accessible materials.

a. Poly vinyl chloride (PVC) b. Poly vinylidene chloride (PVDC) c. Poly vinyl acetate (PVAc) d. Poly urethane (PU)e. Ethylene propylene diene monomer rubber (EPDM) f. Ethylene vinyl acetate (EVA) g. Other foam plastics (except polyolefins)h. Natural and synthetic rubberi. Siliconej. Thermoplastic elastomers (TPEs)k. Plastic materials other than polyolefins with shore A hardness < 90

Children's toys and childcare articles, before and after use and abuse testing, shall not contain concentrations of more than 0.1% BBP, DBP or DEHP, individually.

Children's toys that can be placed in the mouth or childcare articles, before and after use and abuse testing, shall not contain concentrations of more than 0.1% DINP, DIDP or DnOP, individually.

In case of insufficient material for testing found on number of samples specified in the protocol, vendor needs to provide components/parts for testing.

Report actual results or include data table within report. Issue a third party test report. Component testing is allowed. Compositing up to 3 like materials is allowed. If the composite result exceeds the adjusted limit (regulatory limit divided by the number of components) and ON REQUEST, individual materials will be analyzed.

M PASS



Rating Key: M Meets NM Does Not Meet NA Not Applicable NR Not Requested * Additional Charge For This Test

No. Of Samples Required For Complete Testing: 6 No. Of Working Days For Complete Testing: 7 Creation Date: SEPTEMBER 2, 2009

Editorial Revision Date: AUGUST 05, 2013 Pricing Review Date: Technical Review Date: DECEMBER 4, 2009 Revision No: 21

report - guillow's - 2000fe... · 2016. 3. 25. · report bureau veritas consumer products...

Documents