Retaining walls self-adhesive membrane

13TECHNICAL PROPOSAL

Retaining wallsaDesO® self-aDhesive

membRane

issUe: 013

Date: 11.12

RevisiOn: 3

by: POlyglass

POLYGLASS SPARegistered Office: Viale Jenner, 4 - 20159 MILANO

Head Office: Via dell’Artigianato, 3431047 Ponte di Piave (TV) - Italy

Tel. +39 04227547 - Fax +39 0422854118www.polyglass.com - info@polyglass.it

Detail A

Detail A

1 Perimetral foundation wall

2 bituminous primer

3 bituminous membrane (1st layer)

4 bituminous membrane (2nd layer)

5 POlyfOnD Kit drainage layer)

6 Non-woven fabric filtration layer

7 Perforated drainage tube

8 Refill

TECHNICAL SPECIFICATIONS ITEMS1. Concrete walls cleaned from all cement grout and formwork

rods; the concrete must be clean, dry, and seasoned. A rounded edge in mortar of cement will be installed at the foot of the turn-ups to permit correct membrane positioning.

2. All surfaces on which the waterproofing layer is laid on-site must be previously given a coat of a bituminous primer (POLYPRIMER HP 45 PROFESSIONAL by POLYGLASS S.p.A.) with 20÷25 viscosity in FORD Cup no. 4 at 25 °C. Wait until the primer is completely dry (15-20 hours) before applying the waterproofing layer.

3. The first waterproofing layer will be composed of an ADESO® waterproofing membrane made from a distilled bitumen elastomeric compound (SBS) with innovative self-adhesive compound layering technology. The 2 mm thick Professional Use membrane is made from a staple non-woven polyester fabric reinforced and stabilised by longitudinal glass fibre (ELASTOFLEX SA P by POLYGLASS S.p.A. - produced by UNI EN ISO 9001:2008 and UNI EN ISO14001:2004 certified Quality System; conformity marking with intended use as per EN 13707 Multiple layer). This membrane with -20 °C cold flexibility is made with the quality standards ensured by N.A.T.® (NO AGEING TECHNOLOGY, an innovative productive system that permits control over the polymeric ageing process of bituminous membranes). The membrane can be applied with perfect adherence to the layer previously applied after stripping away the monosiliconated release film from the self-adhesive side with overlaps of at least 10 cm on the sides and 15 cm on the heads; bonding occurs with the direct contact of the overlapping parts and light rolling with a metal roller. The layer must be turned up and bonded by torching without interruption along the walls to the top of the vertical turn-up. Some operations or technical details can be facilitated by heating the membrane with hot air guns or light torching with propane gas.

4. The second waterproofing layer will be composed of an ADESO® waterproofing membrane made from a distilled bitumen elastomeric compound (SBS) with innovative self-adhesive compound layering technology. The 2 mm thick Professional Use membrane is made from non-woven flocking polyester reinforced and stabilised by longitudinal glass fibre (ELASTOFLEX SA P by POLYGLASS S.p.A. - produced by UNI EN ISO 9001:2008 and UNI EN ISO14001:2004 certified Quality System; conformity marking with intended use as per EN 13969 Multiple layer membranes for foundations). The membrane can be applied with perfect adherence to the layer previously applied after stripping the monosiliconated release film away from the self-adhesive side with overlaps of at least 10

cm on the sides and 15 cm on the heads; bonding occurs with the direct contact of the overlapping parts. The layer must be turned up and bonded by torching without interruption along the walls to the base of the foundation plinth. Some operations or technical details can be facilitated by heating the membrane with hot air guns or light torching with propane gas. All the membranes forming the second waterproofing layer must be laid in the same direction as the first with longitudinal and transversal overlapping equal to or greater than the width of the bonding beam. After laying on-site, both membranes must be mechanically fastened to the top of the wall in order to avoid slippage using metal washers and fixings or the appropriate metal flashing.

5. POLYFOND KIT DRAIN by POLYGLASS S.p.A., a protective drainage system made a with a new mixture of HDPE in truncated cone embossing bonded to white needle-loomed non-woven polypropylene fabric with 110 g/m2 density ensures waterproofing seal protection and rainwater drainage. The protective system is fastened using a perforated HDPE finishing strip 200 cm long, 7 cm high. The protective system can be fastened by impact with washers and nails in 25 mm galvanized steel.

6. For positioning at the base of the foundation of a perforated drainage tube sheathed in non-woven fabric.

7. Refill using clean backfill free from construction debris laid on-site, with care to avoid damaging the mechanical protection provided previously.

TECHNICAL PROPOSAL13 Retaining walls self-adhesive membrane roofing

1 2 4 53

3

2

1 Muro in calcestruzzo

Primer bituminoso

POLYGLASS SpA - MAPEI GROUP - Sede legale Viale E. Jenner, 4 20159 Milano

Sede amministrativa via Dell'Artigianato, 34 31047 Ponte di Piave (TV)

tel. +39 04227547 - fax +39 0422854118 - www.polyglass.com e-mail: info@polyglass.it

riproduzione vietata15.04.2011

Stratigrafia

Muri contro terra

Membrana bituminosa (primo strato)

5

4

Sistema protettivo e drenante POLYFOND KIT DRAIN

Membrana bituminosa (secondo strato)

Retaining walls self-adhesive membrane roofing TECHNICAL PROPOSAL

TECHNICAL CHARACTERISTICSTEST METHOD TECHNICAL

CHARACTERISTICSUNIT OFMEASURE

NOMINAL VALUES

EN 1848-1 LENGTH m 15 (-1%)EN 1848-1 WIDTH m 1 (-1%)EN 1848-1 STRAIGHTNESS mm/10 m ExceedsEN 1849-1 THICKNESS mm 2 (±0,2)EN 1849-1 MASS PER UNIT AREA kg/m2 NPDEN 1928-B WATERTIGHTNESS kPa ExceedsEN 1928-A RESISTANCE TO WATER PENETRATION mm/H2O -EN 1928-BEN 1296

WATERTIGHTNESS AGAINST ARTIFICIAL AGEING kPa Exceeds

EN 1928-BEN 1847

WATERTIGHTNESS AGAINST CHEMICAL kPa Exceeds

EN 13897 WATER TIGHTNESS AFTER STRETCHING % -EN 13501-5 ExTERNAL FIRE PERFORMANCE - FRoof

EN 13501-1 REACTION TO FIRE Euroclass FEN 12316 PEEL RESISTANCE N/50 mm -EN 12317 SHEAR RESISTANCE N/50 mm -

EN 12311-1

TENSILE PROPERTIES MAxIMUM LOAD AT BREAK LongitudinalTransversal ELONGATION AT BREAKLongitudinalTransversal

N/50 mmN/50 mm

%%

400 (-20%)300 (-20%)

35 (-15)35 (-15)

EN 12691-A RESISTANCE TO IMPACT mm ≥400EN 12730-A RESISTANCE TO STATIC LOADING kg ≥10

EN 12310-1RESISTANCE TO TEARINGLongitudinalTransversal

NN

130 (-30%)130 (-30%)

EN 1107-1 DIMENSIONAL STABILITY % -EN 1108 FORM STABILITY UNDER CYCLIC TEMPERATURE CHANGE % -EN 1109 COLD FLExIBILITY °C ≤-20EN 1110 FLOW RESISTANCE AT ELEVATED TEMPERATURE °C ≥100EN 1110EN 1296

ARTIFICIAL AGEING BEHAVIOUR (COLD FLExIBILITY) °C -

EN 1296 - EN 1297EN 1928

ARTIFICIAL AGEING BEHAVIOUR RESISTANCE TO WATER PENETRATION mm/H2O -

EN 1296 - EN 1297EN 12311-1

TENSILE PROPERTIES AGAINST ARTIFICIAL AGEINGMAxIMUM LOAD AT BREAKLongitudinalTransversalELONGATION AT BREAKLongitudinalTransversal

N/50 mmN/50 mm

%%

--

--

EN 12114 RESISTANCE TO PENETRATION OF AIR - -EN 12039 ADHESION OF GRANULES % -EN 1931 WATER VAPOUR PROPERTIES μ 20000EN 1850-1 VISIBLE DEFECTS - AbsentASTM D 1000 PEELING N/10 mm ≥20

ELAS

TOFL

EX S

A P

13

TECHNICAL CHARACTERISTICS of THE pRoTECTIoNTECHNICAL CHARACTERISTICS

NOMINAL VALUES

MATERIAL High density polyethylene (HDPE) stud membrane with a polypropylene geotextileDRAINAGE MATERIAL White polypropylene geotextile of 110 g/m2

COLOUR BlackCERTIFIED COMPRESSION RESISTANCE ≥ 230 kN/m2 (23 ton/m2)ROLLS SIzE (M) 2,0 x 20 HEIGHT OF THE STUDS 8 mmNUMBER OF STUD FOR M2 About 1860AIR VOLUME BETWEEN STUDS About 5 l/m2

DIMENSION TOLERANCE +/- 4%DRAINAGE CAPABILITY 4,6 l/s/m2

THERMAL STABILITY From -40 °C / +80 °C

CHEMICAL AND PHYSICAL PROPERTIES Resistant to chemical agents, roots, not polluting water, resistant to fungal and bacterial contamination; non degradable

COMBUSTION CLASS B2 in compliance to DIN 4102

POLY

FOND

KIT

DRA

IN

ELASTOFLEx SA P: In compliance with EN 13707 product standards (layers for roofing), EN 13969 TYPE T (foundations) and EN 13859-1 (under tile).

TECHNICAL PROPOSAL

POLYGLASS SPARegistered Office: Viale Jenner, 4 - 20159 MILANO - Head Office: Via dell’Artigianato, 34 - 31047 Ponte di Piave (TV) - Italy

Tel. +39 04227547 - Fax +39 0422854118 - www.polyglass.com - info@polyglass.it

13

11/1

2

Retaining wallsaDesO® self-aDhesive

membRane

issUe: 013

Date: 11.12

RevisiOn: 3

by: POlyglass

POLYGLASS SPARegistered Office: Viale Jenner, 4 - 20159 MILANO

Head Office: Via dell’Artigianato, 3431047 Ponte di Piave (TV) - Italy

Tel. +39 04227547 - Fax +39 0422854118www.polyglass.com - info@polyglass.it

APP, SBS, TPO Waterproofing compound

Lateral adhesive overlap

SELF-ADHESIVE Compound

Reinforcement

Removable monosiliconized film

Self-adhesive end-lap.Granule-free end-lap

Retaining walls self-adhesive membrane roofing

Detail A

Detail A

1 Perimetral foundation wall

2 bituminous primer

3 bituminous membrane (1st layer)

4 bituminous membrane (2nd layer)

5 POlyfOnD Kit drainage layer)

6 Non-woven fabric filtration layer

7 Perforated drainage tube

8 Refill