retrofit kit 30w he 2x4' titanium led series 2...titanium led series 2.0 111144 easy 3-5...
TRANSCRIPT
TITANIUM LED SERIES 2.0
111144Easy 3-5 minutes installationUniversally compatible to upgrade 2x4' troffer and louver Exceptional efficacy 143 LPW120-277V circuit and 0-10V dimming control compatible High performance lighting distribution and low glare lensExtra long 100,000 hour lifetime
WARRANTY
YR
10
100,000 H
PRO
82
UNIVERSAL
WIDE BEAM
RETROFIT KIT 30W HE 2X4'
BALLASTCOMPATIBLE
www.greencreative.com / [email protected] - Tel / Fax: (866) 774-5433 - / GREENCREATIVELED / GClightingLED / GREEN CREATIVE
EFFICIENCY AT WORK
ELECTRONIC
TM 21 IES
143
SPECIFICATIONSINSTALLATION GUIDE
Step 1.
Step 2.
Step 3.
Step 4.
Step 5.
Step 6.
Step 7.
Step 8.
Make sure the POWER IS TURNED OFF at the source to the location at which you are installing the product.Remove existing lamps, door frame (if applicable), reflector and ballast cover. Gently lift the original luminaire housing and slide in both side mounting brackets between the housing and the T-grid. (fig. 1)Hang the retrofit kit body by hooking the T-hinges into the respective slots on one of the mounting brackets. (fig. 2)
Attach the safety cables to the original luminaire housing using the self-tapping hex head screws and washers provided. (fig. 3) Connect the retrofit kit power to the AC power. Connect the power supply to the retrofit kit. (fig. 4) Close the retrofit kit by pushing it up and securing both latches. (fig. 5) Return power back to the source and installation is complete. (fig. 6)
RETROFIT KIT 30W HE 2X4'
1.
4.
2.
5.
3.
6.
RETROFIT KIT INSTALLATION
* Suitable for damp locations. Not for use where directly exposed to the weather or water
Fig. 1 Fig. 5
Fig. 2
Fig. 3
Fig. 4
OFF
ON
OFF
ON
DIRECT INSTALLATION
Switch off power to the luminaire (fig. 1) and remove diffuser (if provided)Remove the existing fluorescent lamp(s) from the luminaire (fig. 2)Note: Verify that the fluorescent tube type is listed on the LED lamp label
Install GREEN CREATIVE T8 LED lamp (one for each fluorescent lamp removed) (fig. 3)Twist the GREEN CREATIVE T8 LED lamp firmly into the lamp holders (fig. 4)Switch on power to the luminaire (fig. 5)
SPECIFICATIONS
Type
Power (W)
Voltage - Frequency
Color Temp. (ANSI)
CRI (Ra)
Typical lumens (lm)
Efficacy (LPW)
Beam Angle
Dimmable
Power Factor
THD
Rated Lifetime - L70 (hrs.)
Rated Lifetime - L90 (hrs.)
L x W x H (w/ brackets)
L x W x H (w/o brackets)
Weight (lb. / g)
Product
Model 28341
30TROFKIT24DIM/830/277V
28342
30TROFKIT24DIM/835/277V
28343
30TROFKIT24DIM/840/277V
2x4' Troffer Retrofit Kit
30
120-277V 50-60Hz
Warm White 3000K
82
4200
140
120°
Yes
0.9
<20%
100,000
44,000
47.83"x23.94"x2.76"(1215x608x70mm)
46.77"x20.59"x2.76"(1188x523x70mm)
18.83lb. / 8.54kg
2x4' Troffer Retrofit Kit
30
120-277V 50-60Hz
Neutral White 3500K
82
4200
140
120°
Yes
0.9
<20%
100,000
44,000
47.83"x23.94"x2.76"(1215x608x70mm)
46.77"x20.59"x2.76"(1188x523x70mm)
18.83lb. / 8.54kg
2x4' Troffer Retrofit Kit
30
120-277V 50-60Hz
Cool White 4000K
82
4300
143
120°
Yes
0.9
<20%
100,000
44,000
47.83"x23.94"x2.76"(1215x608x70mm)
46.77"x20.59"x2.76"(1188x523x70mm)
18.83lb. / 8.54kg
Dimming
Power
Ground
RETROFIT KIT 30W HE 2X4'
Ref
.:# D
S20
9-TR
OFK
IT-3
0W-2
X4-2
6021
8
PRODUCT ORDERING INFORMATION
ACCESSORY ORDERING INFORMATION
Options (Factory Installation): Select or Leave Blank
Must SelectPower
30TROFKIT24DIM
30W
Model
SENSORRC
Product
97881
Description
Remote Control for OCCDIM
30
3000K
35
3500K
40
4000K
8
82
277V
120-277V
(Blank)
None
STEPDIM
Step Dimming 100/50
(Blank)
None
OCCDIM
Microwave Sensor
(Blank)
None
EM
10W EM Backup
CRI CCT Voltage Step Dimming Sensor EM Backup
Ex. 30TROFKIT24DIM/840/277V/OCCDIM/EM