Wireless Selective Circuit Monitoring

© 2018 Packet Power LLC SCM V3

Monitoring applications

1.2

Panelboard input feeds

Panelboard selective circuits

HVAC, Generators and high energy

loads

Existing switchgear

Tenant submetering

Data Center PUE

Packet Power provides a simple, cost-effective way to monitor single- and three-phase circuits up to 600V and 6000A. The complete, pre-configured monitoring units transmit data using

a self-configuring wireless network and can be installed and delivering data in minutes.

Revolutionizing multi-circuit monitoring

Built to your specifications Cuts installation time in half

• Voltage source type

• Voltage source quantity

• Voltage lead color and length

• CT type and rating

• CT quantity

• CT lead length

• Wire exit location

• Over-current protection

• Monitoring current only and/or full power

• Custom panel map (optional)

Comes pre-configured for:

© 2018 Packet Power LLC SCM V3 - Page 2

Wireless Selective Circuit Monitoring

Multi-circuit Monitors

Current Transformers

Additional current ratings available

Split Core CTsInside Diameter Maximum Amperage

10 mm 36, 63

16 mm 120, 240

24 mm 120, 240

36 mm 240, 360, 480

50 mm 240, 360, 480, 720, 960, 1200, 1440

75x125 mm 360, 720, 960, 1200, 1800

150x150 mm 960, 1200, 1440, 1920, 2400, 3600, 4800, 6000

Solid Core CTsInside Diameter Maximum Amperage

8 or 9 mm 38

13 mm 70

32 mm 120, 240, 480

Rogowski Coil CTsMaximum Amperage 250, 500, 1000, 2000, 3000, 4000, 5000

Coil length (inches) 6, 12, 18, 24, 36

Why Packet Power

Open• Compatible with any existing hardware

• Send data to any DCIM or BMS using SNMP, Modbus TCP/IP, Ethernet/IP or MTConnect

Cost effective• Lower installation costs

• Fully self-optimizing wireless network lowers ongoing support costs

Installs easily• Arrives fully configured

• No communication cables

• Pre-wired

• Data is remotely accessible with no programming Wireless that works

• Unique purpose-built wireless protocol can only be used for monitoring

• Full separation of wireless monitoring and wired data network

• Proven in critical facilities worldwide

• Use full power monitoring to track power and energy

• Use current-only monitoring to lower costs and simplify installation

• “Plug and Play” wireless network

• No configuration needed on site

• Highly compact

• Easy panel mapping tool

• Pre-labeled CT leads in 1 to 5 meter lengths

• Optional fusing

Access data instantly from the EMX Energy Monitor cloud service or from existing monitoring applications using SNMP, Modbus TCP/IP, Ethernet/IP or MTConnect.

© 2018 Packet Power LLC SCM V3 - Page 3

Wireless Selective Circuit Monitoring

Packet Power Monitor Configurations

PGXXX modelsCTs: 1-3

Dimensions: 4.5 x 4.5 x 2.7 in

6.3 x 6.3 x 3.6 in

BG02 modelsCTs: 1-12

Dimensions: 6.3 x 6.3 x 3.6 in

BG04 modelsCTs: 2-21

Dimensions: 9.5 x 6.3 x 3.8 in

BG06 modelsCTs: 4-18

Dimensions: 10 x 12 x 2.5 in

BG09 modelsCTs: 7-27

Dimensions: 14 x 12 x 2.5 in

For 48- and 96-pole branch circuit monitoring solutions, go to: www.packetpower.com/panel-board

6.3 inches (160mm), others to scale

Technical SpecificationsMeasurementMeasurements V, A, Ah, VA, W, Wh, Power Factor, Hz, THDi, THDv

Accuracy +/-1.0% (CT dependent); +/-0.5% available

Input voltage 100-600V AC

Input voltage configuration L-N, L-L, 3W+G, 4W+G

Current range Up to 6000A

Frequency 50/60 Hz

CommunicationsOperating frequency 860 to 930 MHz and 2.4 GHz (frequencies vary by region)

Wireless network protocol Frequency hopping self-configuring load-balancing mesh network

Standard protocols SNMP, Modbus TCP/IP, Ethernet/IP, MTConnect

Firmware updates Wireless

Typical transmission range 10 to 30 meters indoors between any two devices in mesh network

Antenna Fully enclosed, fixed configuration

Monitoring unit to gateway ratio Up to 100 monitoring units per gateway with unlimited gateways per site

Multi-site support Yes

Encryption HTTPS, optional 128-bit wireless

Local display Volts, Amps, Watts and communication status

Environmental & MechanicalOperating environment -7° to 75°C (20° to 167°F); 5% to 95% non-condensing

Water and dust resistance NEMA 1/IP20 (indoor use); NEMA 4X available on some products

Power usage 1-7W depending on the product

Certifications Multiple UL, IC, CE and FCC standards

Packet Power’s wireles protocol was designed specifically for critical facilities. The unique protocol is different than WiFi or Zigbee and can only be used for monitoring. It allows for a complete separation of the wireless monitoring network from the wired data network. It is proven to work in data centers and other critical facilties run by major

financial services firms, government agencies, educational institutions and colo companies worldwide.

Secure Wireless Technology

2716 Summer St. NEMinneapolis, MN 55413

USA

Ph +1 (877) 560-8770Fax +1 (866) 324-2511www.packetpower.com

© 2018 Packet Power LLC SCM V3 - Page 4

Proven in data centers worldwide

Wireless Selective Circuit Monitoring

For detailed product specifications, go to: http://bit.ly/SCM-Specs