Follow the drawing to install the lens Carefully align the connectors while installing the lens and fix the safety cable on the machine

LOCK

OPEN

INSTALL

Removal of lens protection sponge

LOCK

OPEN

Follow the drawing to Tie up the lever for lock the lens

OPEN

LOCK

OPEN

LOCK

Click

Press button then press down the lever

REMOVE

DNV-COC-000020

RLM W14 Quick start guide Call for support: USA +1 866 374 7878 EMEA +32 56 368609 APAC +86 400 88 22726

Mounting the lens

Pull out the lens

IMPORTANT:

• Remove the lens before transporting the projector.

• To save lamp lifetime, first switch the projector to standby mode and wait two minutes, then switch off the main power.

• Ensure that the projector is operating with clean filters.

• Do not block the ventilation in and outlets

• Using the projector in a non recommended tilt angle will reduce the lifetime of the lamps or create unexpected behavior of the unit.

• Laser light can cause severe damage to the DMD. This damage is not covered by warranty.

After factory reset the projectors needs some time to scan the inputs before displaying the source.

Auto source can be switched off in the CONTROL menu. The manual selection can be done via menu or other control sys-tems.

Alignment the unit is set as standard in table front projection mode. Change the projector set up in the Alignmentmenu.

If geometrical distortion occurs (H/V keystone), this can be corrected with Keystone in the Alignment menu.

Tuning the image can be done in the IMAGE menu. Default values are 100.

Picture-in-Picture control can be done in the LAYOUT menu. Lamp management in the LAMP menu. Switching off the unit can be done by pressing the STBYbutton for 2 sec. or the button for 2 sec. on the remote control.

13

14

15

16

17

10

11

12

Quick setup and operation

The following summarizes RLM W14 setup and operation. For error-free installation always refer to the listed section in the User Guide.

Connect power. Ensure that the power (90-250 V @ 50/60hz) is properly connected to the RLM W14.

Connect available sources to the appropriate input terminal. Power on. Turn the mains switch to on. Standby LED (blue) must be constantly lit. Start up the unit by pressing the STBY button. Warm up of the unit takes approx. 45 sec till image appears. Image of the source should appear after 15 seconds if the unit is in full auto mode.

Adjust the lens settings by pressing the ENTER button for ZOOM and FOCUS adjust. Toggle to SHIFT by pressing ENTER again. Lens function can also be found in the CONFIGURATION menu.

Factory Reset can be executed in order to put the unit in the full auto mode. Factory reset can be found in the SERVICE menu. Press execute and wait 30 sec.

1

2

3

4

5

6

7

8

9

Printed on FSC certified paper (www.fsc.org)

RLM W14 Quickstart guide dec09outl.indd 1 04/08/14 15:30

LED indication chart Blue(STANDBY)

Green(ON)

Red(ERROR)

Standby

Lamp is approaching end of life

Lamp failure

Lamp door open

Fan failure

Overheating

System error - - - -

Cooling / Warm up

Power on / Normal

INSTALL SAFETY CABLE

MENU

ON

ERROR

STBY

INPUTSSTBY

Buttons and LEDs

STBYUse this button to start up or shutdown the projector.

buttonsUse these buttons to scroll,configure or adjust items onthe OSD or toggle betweendifferent images.

MENUDisplays or hides the OSDadjustment screenPOWER

Displays the projector’s powerstatus

ERRORDisplays the cause of problem(i.e. temperature, fan, lampor system) that has led toprojector malfunction.

STAND BYThe indicator that shows theprojector’s standby status.

ENTERPress this button to confirmselection of OSD item; you canchoose from “Select Item” oraccess “Sub Menu” configurations.

INPUTUsed to toggle between differentinput signal source.Refer to Chapter VI → SignalSource Selection for more details.

IR Address

Eco Network Power

Network

Menu Position

Start Up Logo

Start Up Chime

Button 1

Button 2

Button 3

Button 4

Button 5

Trigger 1

Trigger 2

Auto Source

Language

200mA

Switch on the projector

Switch off the projector. Press for 2 sec

Source selection hot key. Define Hot Keys in the control menu

Navigation key. Enter key for confirmation

Aspect ratio switch

Activate menu or return key

SettingsPause: picture mute (shutter close)Text: deactivate or activate the On Screen TextAuto image: activate the auto image adjustmentContrast: high lights adjustBrightness: low lights adjustSharpness: increase edge detailPhase: adjust phase (analog signals only)Color: color saturationTint: tint adjust (NTSC only)PIP: activate selected Picture-in-PictureSWAP: swap PiP and main imageAddress: change the remote control address to 1 or 2. Press address and enter for 5 sec.

1

2

3

4

5

6

7

1

32

4

1

5

INPUT

ASPECTRATIO

AUTO IMAGE

PAUSE TEXT

MENU

SHARPN

PHASE COLOR TINT

ADDRESSSWAPPIP

1

3

4

6

7

2

5

Menu structure

Using the remote control

PiP/main source availability

Input Selection

Input Configuration

Input Locking

Contrast

Brightness

Sharpness

Noise Reduction

Color Temperature

Input Balance

Aspect Ratio

Timings

Auto Image

Zoom

Main Select

PIP Select

PIP Position

PIP

Mode

Lamps

High Altitude Mode

Power

Lamp1 Status

Lamp2 Status

Lamp1 Run Time

Lamp2 Run Time

Rear Projection

Ceiling Mode

Lens Control

Lens To Midposition

Lens Memory

Lens Calibration

Dynamic Contrast

Gamma

Internal Patterns

Color Space

Model

Serial Number

Software Version

Active/ PIP Source

Pixel Clock

Signal Format

H/V Refresh Rate

Auto Power Off

Auto Power On

No Signal

Auto Image Adjust

Custom Color Space

Blanking

Warp

ScenergiX

Lamp1 Run Time

Lamp2 Run Time

Lamp Hour Reset

Projector Run Time

Blue Only

Factory Reset

RLM W14 Quick start guide

INPUT IMAGE LAYOUT LAMPS ALIGNMENT CONTROL SERVICE

RLM W14 Quickstart guide dec09outl.indd 2 04/08/14 15:30

Connector panel

External control over IP for e.g. Projector Toolset or web browser

Use SDI/HDSDI/3G for professional equipment

Support Full HD uncompressed video

Use HDMI for e.g. PC or Blu-ray player

Use D15 inputfor PC

Dual DVI inputfor 3D source

Use BNC inputs for RGBHV and component signals

External RS232 comm.

Trigger voltage can control e.g. a screen or curtains

Use RCA inputs forcomponent signals

Input/Output connectionfor 3D Sync singal

Main select

Source availabe - source not availabe

PiP

sele

ct

HDBaseT HDMI

YUV1

SDI/HDSDI/3G

RGBHV/YUV2

VGA

HDMI -HDBaseT -

RGBHV/YUV2

--

VGA

-

--- -

YUV1

-

SDI/HDSDI/

3G3D-DVI

------

--