rosewill rhpm-11001 / universal projector mount / user manual

1
NOTE: We recommend that this product is installed by the professional only. we accept no liability for damages caused by incorrect assembly ,installation or use. If there is any doubt, please contact the specialist from the seller for help. Installing the Projector Mount Also make sure that all of the hardware has been included with your mount.You should find the following: Tools required for the installation: • Phillips Head Screw Driver • Electric or Portable Drill IMPORTANT! • For safety reasons, the ceiling or mounting surface must be capable of supporting the combined weight of the mount and the projector; otherwise the structure must be reinforced. • At least two people are required for this installation. Do not attempt to install this mount alone under any circumstance. • Make sure that no electrical cables,water pipes or gas pipes are located within the mounting surface. (A) Drywall Screw X 2 (B) Concrete Anchor X 2 (C) (D) Washer X 4 (E) M4x16 Screw X 4 (F) M4x40 Screw X 4 (G) M6x16 Screw X 4 (H) M6x40 Screw X 4 1 2 3 5 Allen Wrench X 1 1/8” (3 mm) Drill Bit + Stud Finder ( Drywall Installation ) 5/16” (8 mm) Masonry Bit ( Concrete Installation ) Parts referrence: (I) Mount Base x 1 (J) Ceiling Plate x 1 (K) Mount Arm x 4 Attach the Ceiling Plate (J) to the ceiling using the Drywall Screws (A). If you are installing into a concrete ceiling, also use the Concrete Anchors (B). IMPORTANT: If you are not installing into a concrete ceiling, make sure that you screw directly into a wooden joist or other adequate support. A A J Secure the Mount Arms (K) to the Mount Base (I) using the Allen Wrench (C). Note: This step has been done already by the manufacturer. Loosen the Four Screws (a ,b ,c ,d) using the Allen Wrench (C) so that you can adjust the arms easier when attaching the projector. Attach your projector to the Mount Arms (K) using the correct bolt from the hardwar kit (E, F, G, or H). If none of these bolts fit, check with the manufacturer of your projector for the proper size. Once attached, make sure tighten all screws and bolts. NOTE: Please use the Washers (D),if you are using the M4 Screws (E) or (F). 4 Carefully hook the Mount Base (I) with your projector attached to the Ceiling Plate (J). Tighten the knobs on both sides of the Mount Base (I) to pevent the projector from being knocked off the Ceiling Plate (J). Installation is now complete. Tighten Final Adjustment 360° Rotation To change the tilt or direction of your projector,simply loosen the Tilt knob or Three Ball Joint Screws, turn the projector to the desired position and retighten the Tilt knob and/or screws. Tilt knob WARNING:Do not over loosen or tighten the Knob and/or Screws. Allen Wrench (C) Three ball joint screws (e,f,g) e f g b c a d User manual RHPM-11001 Universal Aluminum Projector Mount / Universelle en aluminium pour projecteur

Upload: internet1982

Post on 26-Oct-2014

45 views

Category:

Documents


1 download

TRANSCRIPT

Page 1: Rosewill RHPM-11001 / Universal Projector Mount / User Manual

NOTE: We recommend that this product is installed by the professional only. we accept no liability for damages caused by incorrect assembly ,installation or use. If there is any doubt, please contact the specialist from the seller for help.

Installing the Projector Mount

Also make sure that all of the hardware has been included with your mount.You should find the following:

Tools required for the installation: • Phillips Head Screw Driver • Electric or Portable Drill

IMPORTANT! • For safety reasons, the ceiling or mounting surface must be capable of supporting the combined weight of the mount and the projector; otherwise the structure must be reinforced. • At least two people are required for this installation. Do not attempt to install this mount alone under any circumstance. • Make sure that no electrical cables,water pipes or gas pipes are located within the mounting surface.

(A) Drywall Screw X 2 (B) Concrete Anchor X 2 (C)

(D) Washer X 4 (E) M4x16 Screw X 4 (F) M4x40 Screw X 4

(G) M6x16 Screw X 4 (H) M6x40 Screw X 4

1

2

3

5

Allen Wrench X 1

• 1/8” (3 mm) Drill Bit + Stud Finder ( Drywall Installation )• 5/16” (8 mm) Masonry Bit ( Concrete Installation )

Parts referrence:

(I) Mount Base x 1 (J) Ceiling Plate x 1

(K) Mount Arm x 4

Attach the Ceiling Plate (J) to the ceiling using the Drywall Screws (A).If you are installing into a concrete ceiling, also use the Concrete Anchors (B).

IMPORTANT: If you are not installing into a concrete ceiling, make sure that you screw directly into a wooden joist or other adequate support.

A A

J

Secure the Mount Arms (K) to the Mount Base (I) using the Allen Wrench (C).Note: This step has been done already by the manufacturer.

Loosen the Four Screws (a ,b ,c ,d) using the Allen Wrench (C) so that you can adjust the arms easier when attaching the projector.

Attach your projector to the Mount Arms (K) using the correct bolt from the hardwar kit (E, F, G, or H). If none of these bolts fit, check with the manufacturer of your projector for the proper size. Once attached, make sure tighten all screws and bolts.

NOTE: Please use the Washers (D),if you are using the M4 Screws (E) or (F).

4

Carefully hook the Mount Base (I) with your projector attached to theCeiling Plate (J). Tighten the knobs on both sides of the Mount Base (I)to pevent the projector from being knocked off the Ceiling Plate (J). Installation is now complete.

Tighten

Final Adjustment

360° Rotation

To change the tilt or direction of your projector,simply loosen the Tilt knob or Three Ball Joint Screws, turn the projector to the desired position and retighten the Tilt knob and/or screws.

Tilt knob

WARNING:Do not over loosen or tighten the Knob and/or Screws.

Allen Wrench (C)

Three ball joint screws (e,f,g)

e

fg

b

c

a

d

User manual RHPM-11001Universal Aluminum Projector Mount / Universelle en aluminium pour projecteur