rt 42px20 chassis rf 043b service manual

PLASMA TVSERVICE MANUAL

CAUTIONBEFORE SERVICING THE CHASSIS,READ THE SAFETY PRECAUTIONS IN THIS MANUAL.

CHASSIS : RF-043B

MODEL : RT-42PX20

website:http://biz.LGservice.come-mail:http://www.LGEservice.com/techsup.html

- 2 -

CONTENTS

SAFETY PRECAUTIONS ...................................................................................3

DESCRIPTION OF CONTROLS ........................................................................ 4

SPECIFICATIONS ............................................................................................ 13

ADJUSTMENT INSTRUCTIONS ......................................................................15

TROUBLE SHOOTING GUIDE..........................................................................18

BLOCK DIAGRAM.............................................................................................29

EXPLODED VIEW..............................................................................................32

EXPLODED VIEW PARTS LIST ........................................................................33

REPLACEMENT PARTS LIST...........................................................................34

SCHEMATIC DIAGRAM ........................................................................................

PRINTED CIRCUIT BOARD ..................................................................................

- 3 -

SAFETY PRECAUTIONS

Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by inthe Schematic Diagram and Replacement Parts List. It is essential that these special safety parts should be replaced with the same components as recommended in this manual toprevent X-RADIATION, Shock, Fire, or other Hazards. Do not modify the original design without permission of manufacturer.

General Guidance

An isolation Transformer should always be used duringthe servicing of a receiver whose chassis is not isolated fromthe AC power line. Use a transformer of adequate power ratingas this protects the technician from accidents resulting inpersonal injury from electrical shocks.

It will also protect the receiver and it's components from beingdamaged by accidental shorts of the circuitry that may beinadvertently introduced during the service operation.

If any fuse (or Fusible Resistor) in this monitor is blown, replaceit with the specified.

When replacing a high wattage resistor (Oxide Metal FilmResistor, over 1W), keep the resistor 10mm away from PCB.

Keep wires away from high voltage or high temperature parts.

Due to high vacuum and large surface area of picture tube,extreme care should be used in handling the Picture Tube.Do not lift the Picture tube by it's Neck.

Leakage Current Cold Check(Antenna Cold Check)With the instrument AC plug removed from AC source,connect an electrical jumper across the two AC plug prongs.Place the AC switch in the on position, connect one lead ofohm-meter to the AC plug prongs tied together and touch otherohm-meter lead in turn to each exposed metallic parts such asantenna terminals, phone jacks, etc. If the exposed metallic part has a return path to the chassis, themeasured resistance should be between 1MΩ and 5.2MΩ. When the exposed metal has no return path to the chassis thereading must be infinite.An other abnormality exists that must be corrected before thereceiver is returned to the customer.

Leakage Current Hot Check (See below Figure) Plug the AC cord directly into the AC outlet.Do not use a line Isolation Transformer during this check. Connect 1.5K/10watt resistor in parallel with a 0.15uF capacitorbetween a known good earth ground (Water Pipe, Conduit, etc.)and the exposed metallic parts.Measure the AC voltage across the resistor using ACvoltmeter with 1000 ohms/volt or more sensitivity.Reverse plug the AC cord into the AC outlet and repeat ACvoltage measurements for each exposed metallic part. Anyvoltage measured must not exceed 0.75 volt RMS which iscorresponds to 0.5mA.In case any measurement is out of the limits specified, there ispossibility of shock hazard and the set must be checked andrepaired before it is returned to the customer.

Leakage Current Hot Check circuit

1.5 Kohm/10W

To Instrument'sexposed METALLIC PARTS

Good Earth Groundsuch as WATER PIPE,CONDUIT etc.

AC Volt-meter

IMPORTANT SAFETY NOTICE

0.15uF

- 4 -

DESCRIPTION OF CONTROLS

- When using the remote control aim it at the remote control sensor of the set.- There's maybe a defect in consecutive operation of remote control in specified brightness according to this set feature.

POWERMUTE

TV/AV MULTIMEDIA

LIST ARC MENU

PR

PR

VOLOK

1 2 3

4 5 6

7

PSM SSM

8 9

0

VOL

SPLIT ZOOM PIP/DW SLEEP

REVEAL TEXT/PIP PR+

WIN. SIZE MIXPIP PR-

POSITION TIMESWAP

HOLD INDEXPIP INPUT

?

i

I/II

MULTIMEDIASelects the Component, RGB or DVI

modes.

PIP/DWSwitches the sub picture on or off.

Selects PIP or DW modes.PIP PR + /-

Selects a programme for the sub picture.SWAP

Alternates between main and sub pic-ture.

PIP INPUTSelects the input mode for the sub pic-

ture.WIN.SIZE

Adjusts the sub picture size.POSITION

Moves the sub picture to DD / EE or FF / GGdirection.

POWERswitches the set on from standby oroff to standby.

ARC Changes the picture format.

MENUDisplays on screen menus one byone.Exits the current menu.Memorizes menu changes.

SWAPReturns to the previously viewedprogramme.Note : This function works onlywhen Favorite programme is set to Off.Otherwise each press of this buttonwill select a stored favorite pro-gramme.

SSMTo select the sound appropriate toyour viewing programme character.

NUMBER buttons

SLEEPSets the sleep timer.

I/IISelects the language during dual lan-guage broadcast.Selects the sound output.

TEXTThese buttons are used for teletext.For further details, see the ÔTeletextÕsection.Note : In teletext mode, the PIP PR+/-, SWAP and PIP INPUT buttons areused for teletext function.

LISTDisplays the program table.

TV/AVSelects the TV, AV, Component, RGB

or DVI modes.

MUTESwitches the sound on or off.

DD / EE (Programme Up/Down)selects a programme or a menu item.

switches the set on from standby.FF / GG (Volume Up/Down)

adjusts the volume.adjusts menu settings.

OKaccepts your selection or displays the

current mode.

PSMAdjusts the factory preset picture

according to the room.

SPLIT ZOOMEnlarge the screen with regular

ration.

- 5 -

<Front Panel Controls>

ON/OFF

TV/AV MENU VOL PR

TV/AV MENU VOL PR

- Shown is a simplified representation of the set.- Here shown may be somewhat different from your set.

Main Power Button

Remote Control Sensor

TV/AV ButtonSelects the TV, AV, Component,RGB or DVI modes. If OSD is dis-played, selects menu item.

MENUDisplays on screen menus one by one.Exits the current menu.Memorizes menu changes.

DD / EE (Programme Up/Down)selects a programme or a menu item.

switches the set on from standby.FF / GG (Volume Up/Down)

adjusts the volume.adjusts menu settings.

Power Standby IndicatorIlluminates red in standbymode, Illuminates greenwhen the set is turned on

or

- 6 -

<Back Panel>

RS-232C INPUT(CONTROL/SERVICE)

REMOTECONTROL

DVI INPUT

S-VIDEO

AUDIO VIDEO

MONITOROUTPUT

A/VINPUT1

AUDIO

R L

AntennaAC INPUT

VIDEO

INPUT 2COMPONENT

INPUT 1COMPONENT

AUDIO INPUT RGB INPUT

R L/MOND

S-V

IDE

OV

IDE

OA

UD

IO

AV2

RL/

MO

NO

1. CONTROL LOCK / REMOTE CONTROL

2. RS-232C INPUT(CONTROL/SERVICE) PORTConnect to the RS-232C port on a PC.

3. DVI INPUT / AUDIO INPUT / RGB INPUTConnect the monitor output socket of the PERSONAL COM-PUTER to this socket.

4. COMPONENT INPUTConnect DVD video outputs to Y, PB, PR of COMPONENTINPUT and audio outputs to Audio sockets of AUDIO INPUT.

5. AUDIO/VIDEO IN SOCKETS (AV1)Connect the audio/video out sockets of external equipment tothese sockets.S-VIDEO/AUDIO IN SOCKETS Connect the S-VIDEO out socket of an VCR to the S-VIDEOsocket. Connect the audio out sockets of the VCR to the audio sock-ets as in AV1.

6. ANTENNA INPUT

7. POWER CORD SOCKETThis Monitor operates on an AC power. The voltage is indi-cated on the Specifications page. Never attempt to operatethe Monitor on DC power.

8. AUDIO/VIDEO IN SOCKETS (AV2)S-VIDEO/AUDIO IN SOCKETS

3 4 5 76

8

1 2

- 7 -

- Be careful for the bronze wire not to be bended in connecting to antenna input port.

Antenna Connection

INPUT

S-VIDEO

AUDIO VIDEO

MONITOROUTPUT

A/VINPUT1

AUDIO

R LAntenna

AC INPUT

VIDEO

INPUT 2COMPONENT

INPUT 1COMPONENT


R L/MOND

Watching VCR- When connecting the Monitor to external equipment, match the colours of connecting ports (Video - yellow, Audio (L) - white,

Audio (R) -red).- Connect the VIDEO INPUT socket (yellow) to the VIDEO INPUT on the set.- If you have a mono VCR, connect the audio cable from the VCR to the AUDIO (L/MONO) input on the set. - If you connect an S-VIDEO VCR to the S-VIDEO input, the picture quality is improved; compared to connecting a regular VCR

to the Video input. - Use the orbiter function to Avoid having a fixed image remain on the screen for a long period of time. Typically a frozen still pic-

ture from a VCR. (Refer to p. 25)If a 4:3 picture format is used; the fixed image may remain visible on the screen.

- To avoid picture noise (interference), leave an adequate distance between the VCR and set.

Watching TV programmes- Turn the set on and select the programme you

want.

Watching VCR1. Use the TV/AV button on the remote control to

select AV1 or AV2.- If both S-VIDEO and VIDEO sockets have been

connected to the S-VHS VCR simultaneously, onlythe S-VIDEO can be received.

2. Insert a video tape into the VCR and press thePLAY button on the VCR.(See VCR ownerÕs manual)

S-VIDEO

AUDIO VIDEO

MONITOROUTPUT

A/VINPUT1

AUDIO

R L

AntennaAC IN

VIDEO

INPUT 2COMPONENT

INPUT 1COMPONENT

RGB INPUT

R L/MOND

Apartments(connecting to wall antenna socket)

Private house(connecting to wall outdoor antenna)

outdoor antenna

wall antenna socket

VHF antenna

UHF antenna

RF coaxial wire (75 ohms)< Back panel of the set >

< Back panel of the set >

< VCR >

- 8 -

Watching Cable TV- After subscribing for a local cable TV station and installing a converter you can watch cable TV.- For further information of cable TV, contact the local cable TV station.

To watch cable TV

1. Use the TV/AV button on the remote control toselect AV1 or AV2.

2. Tune to cable service provided channels usingthe cable box.

Watching external AV source- When connecting the set to an external source, match the colours of AUDIO/VIDEO input jacks on the set with the output jacks

on the audio/video equipment: Video = yellow, Audio (Left) = white, Audio (Right) = red.

How to use1. Use the TV/AV button on the remote control to

select AV1 or AV2.2. Operate the corresponding external equipment.

See external equipment operating guide.

S-VIDEO

AUDIO VIDEO

MONITOROUTPUT

A/VINPUT1

AUDIO

R L

An

VIDEO

INPUT 2COMPONENT

INPUT 1COMPONENT


R L/MOND

R LAUDIO VIDEO

S-VIDEO

AUDIO VIDEO

MONITOROUTPUT

A/VINPUT1

AUDIO

R L

AntennaAC INP

VIDEO

INPUT 2COMPONENT

INPUT 1COMPONENT

RGB INPUT

R L/MOND


< Cable box >


Camcorder

Video game set

- 9 -

Watching DVD

How to connectConnect DVD video outputs to Y, PB, PR of COMPO-NENT INPUT and audio outputs to Audio sockets ofAUDIO INPUT.

How to use1. Turn on the DVD player, and insert a DVD.2. Use TV/AV or MULTIMEDIA button on the remote

control to select Component 1 or Component 2. Refer tothe DVD player's manual for operating instructions.

¥ Component Input portsYou can get better picture quality if you connectDVD player with component input ports as below.

Component ports of theset

Y PB PR

Video output ports of DVD player

YYYY

PbB-YCbPB

PrR-YCrPR

S-VIDEO

AUDIO VIDEO

MONITOROUTPUT

A/VINPUT1

AUDIO

R L

AntennaAC INPU

VIDEO

INPUT 2COMPONENT

INPUT 1COMPONENT

UT RGB INPUT

R L/MOND

R

R R

R


< DVD player >

Watching DTV (option)- To watch digitally broadcast programs, purchase and connect a digital set-top box.

How to connect1. Use the monitorÕs COMPONENT (Y, PB, PR) INPUT, RGB or DVI

jack for video connections, depending on your set-top box con-nector. Then, make the corresponding audio connections.

How to use1. Turn on the digital set-top box. (Refer to the ownerÕs manual for

the digital set-top box.) 2. Use TV/AV or MULTIMEDIA on the remote control to select

Component 1, Component 2 or RGB.

RS-232C INPUT(CONTROL/SERVICE)

DVI INPUT

S-VIDEO

AUDIO VIDEO

MONITOROUTPUT

A/VINPUT1

AUDIO

R L

VIDEO

INPUT 2COMPONENT

INPUT 1COMPONENT


R L/MOND

(R) AUDIO (L) Y PB RP(R) AUDIO (L) DTV OUTPUT

R

R R

RR

¥ DTV Input signal

576p(50Hz)

1080i(50Hz)

1152i(50Hz)

ModeTerminal Component

o

o

o

RGB (DTV)

o

o

o


< Digital Set-top box >

- 10 -

Connecting PC- To enjoy vivid picture and sound, connect a PC to the set.- Avoid keeping a fixed image on the setÕs screen for a long period of time. The fixed image may become permanently imprinted on

the screen; use a screen saver when possible.- Connect PC to the RGB INPUT(PC INPUT) or DVI INPUT(DIGITAL RGB INPUT) port of the set; change the resolution output of

PC accordingly.- There might be a noise according to some resolution, vertical pattern, contrast or brightness in PC mode. Then change the PC

mode into other resolution or change the refresh rate into other rate or adjust the brightness and contrast on the menu until thepicture is clean. If the refresh rate of the PC graphic card can not be changed, change the PC graphic card or consult it to themanufacturer of the PC graphic card.

- The synchronization input form for Horizontal and Vertical frequencies is separate.

Setup Instructions to Connect a PC to your set- We recommend using 640x480, 60Hz for the PC mode, they provide the best picture quality.- If the resolution of PC is over UXGA, there will be no picture on the set.- Connect the signal cable from the set output port of the PC to the RGB INPUT port of the set or the signal cable from the DVI out-

put port of the PC to the DVI INPUT port on the set.- Connect the audio cable from the PC to the Audio input on the set. (Audio cables are not included with the set).- If using a sound card, adjust PC sound as required.- This set apply a VESA Plug and Play Solution. The set provides EDID data to the PC system with a DDC protocol. The PC adjusts

automatically to use this set.- DDC protocol is preset for RGB (Analog RGB), DVI (Digital RGB) mode.- If required, adjust the set settings for Plug and Play functionally.- If graphic card on the PC does not output analog and digital RGB simultaneously, connect only one of both RGB INPUT or DVI

INPUT to display the PC on the set.If graphic card on the PC does output analog and digital RGB simultaneously, set the set to either RGB or DVI; (the other modeis set to Plug and Play automatically by the set.)

- DOS mode may not work depending on video card if using a DVI-I cable.

232C INPUTTROL/SERVICE)

DVI INPUT

AU

AUDIO

R L

VIDEO

INPUT 2COMPONENT

INPUT 1COMPONENT


R

PC Setup1. Turn on the PC and apply power to the set.2. Turn on the display by pressing the POWER button on

the setÕs remote control.3. Use the TV/AV or MULTIMEDIA button on the remote

control to select the RGB or DVI input source.4. Set the resolution output of the PC to SXGA or under

(1280 x 1024, 60Hz). (Refer to p. 13)


- 11 -

RGB / DVI mode

Resolution

640x350

720x400

640x480

848x480

800x600

HorizontalFrequency(KHz)

VerticalFrequency(Hz)

852x480

832x624

1024x768

1152x864

1152x870

1280x960

1280x1024

31.468

37.861

31.469

37.927

31.469

35.000

37.861

37.500

43.269

31.500

37.799

39.375

31.500

37.799

39.375

35.156

37.879

48.077

46.875

53.674

49.725

48.363

56.476

60.023

68.677

54.348

63.995

67.500

77.487

68.681

60.023

63.981

70.09

85.08

70.08

85.03

59.94

66.66

72.80

75.00

85.00

60.00

70.00

75.00

60.00

70.00

75.00

56.25

60.31

72.18

75.00

85.06

74.55

60.00

70.06

75.02

85.00

60.05

70.01

75.00

85.00

75.06

60.02

60.02

- 12 -

D-sub 15 pin cable

AS mark

LG TV

OwnerÕs Manual

1.5V1.5V

Alkaline batteries

Power Cord

POWERMUTE

TV/AV MULTIMEDIA

LIST ARC MENU

PR

PR

VOLOK

1 2 3

4 5 6

7

PSM SSM

8 9

0

VOL

SPLIT ZOOM PIP/DW SLEEP

REVEAL TEXT/PIP PR+

WIN. SIZE MIXPIP PR-

POSITION TIMESWAP

HOLD INDEXPIP INPUT

?

i

I/II

Remote Control handset

DVI-D Cable

- Optional extras can be changed or modified for quality improvement without any notification new optional extras can beadded.

- Contract your dealer for buying these items.

Optional Extras

Tilt wall mounting bracket

404250 40 42 50

Video cables Audio cablesCeiling mounting bracket

40

4250

42

40

- Secure the TV assembly by attaching it to a wall for additional support.

Attaching the TV assembly to the wall

¥ Install the TV brackets on the TV as shown.Insert the 2 bolts and tighten securely, in the upper holes on the bracket. Install the wall brackets on the wall with 4 bolts*, (not supplied with the prod-uct), as shown.Match the height of the TV brackets and the wall brackets. Check to be sure the brackets are tightened securely.

¥ Secure the TV assembly to the wall with strong strings or wound wire cables,(not supplied with the product), as shown.

2-TV brackets2-Wall brackets

2-TV bracket bolts

- 13 -

SPECIFICATIONSNOTE : Specifications and others are subject to change without notice for improvement.

V Application RangeThis spec is applied to the 42ÓPDP TV used RF-043B Chassis.

V Specification

Each part is tested as below without special appointment.1) Temperature : 25¡ 5¡C (77¡ 9¡F)2) Relative Humidity: 65¡ 10%3) Power Voltage: Standard Input voltage (100V~240V@ 50/60Hz)

* Standard Voltage of each product is marked by models.4) Specification and performance of each parts are followed each drawing and specification by part number in

accordance with BOM.5) The receiver must be operated for about 20 minutes prior to the adjustment.

V Test and Inspection Method1) Performance : LGE TV test method followed.2) Demanded other specification

Safety: CE, IEC specificationEMC : CE, IEC

V General Specification

1. General Specification

Appliance

TEST

TEST

Remark

Safety : IEC/EN60095

EMI : EN55013

EMS : EN55020

Safety : IEC60065

EMI : CISPR13

Model Name

RT-42PX10

RZ-42PX10

Market

EU

Non-EU

Remark

PDP

Maker : NBK / Mitsui / LG Chemical

LGE SPEC

Maker : SONY / Murata / Sanken

Specification

42 inch wide Color Display Module

16:9

PDP42V6xxxx,RGB Closed Type

45% Total light transmittance (E- Mesh)

1) Temp : 0~40 deg

2) Humidity : 0~85%

1) Temp : -20~60 deg

2) Humidity : 0~85%

AC100 ~ 240V, 50/60Hz

No

1

2

3

4

5

6

7

Item

Display Screen Device

Aspect Ratio

PDP Module

Screen Filter

Operating Environment

Storage Environment

Input Voltage

2. Model Specification

(1) RZ-42PX10

(2) RT-42PX10

Item

Market

Broadcasting

Receiving system

Scart Jack ( 3EA )

Video Input(2EA)

S-Video Input(2EA)

Component Input(1EA)

RGB Input(1EA)

DVI Input(1EA)

Audio Input(4EA)

Wired Control

Specification

EU

PAL B/G/I/D/K, SECAM L/L

Upper Heterodyne

PAL, SECAM

PAL, SECAM, NTSC

PAL, SECAM, NTSC

Y/Cb/Cr, Y/Pb/Pr

RGB-PC

DVI-PC

PC Audio, Component,AV(2EA)

Discrete IR

Remark

4 System :

PAL B/G/I/D/K, SECAM L, NTSC4.43,PAL60

4 System :


DVI-D

L/R Input

- 14 -

No

8

9

10

11

12

13

14

15

16

17

18

Remark

4 System :


4 System :


4 System :


DVI-D

L/R Input

Specification

Non-EU

PAL B/G/I/D/K, NTSC

Upper Heterodyne

PAL, SECAM, NTSC

PAL, SECAM, NTSC

PAL, SECAM, NTSC

Y/Cb/Cr, Y/Pb/Pr

RGB-PC

RGB-DTV(for Australian)

DVI-PC

PC Audio, Component,AV(2EA),

AV(2EA)

Discrete IR

No

19

20

21

22

23

24

25

26

27

28

29

Item

Market

Broadcasting

Receiving system

Video Input(2EA)

Video Output(1EA)

S-Video Input(2EA)

Component Input(2EA)

RGB Input

DVI Input

Audio Input(5EA)

Wired Control

- 15 -

1. Application RangeThe spec sheet is applied all of the 42ÓPDP TV, RF-043Bchassis by manufacturing LG TV Plant or sort plants.

2. Specification(1) Because this is not a hot chassis, it is not necessary to

use an isolation transformer. However, the use of isolationtransformer will help protect test instrument.

(2) Adjustment must be done in the correct order.(3) The adjustment must be performed in the circumstance of

25±5¡C of temperature and 65±10% of relative humidity ifthere is no specific designation.

(4) The input voltage of the receiver must keep 100~220V,50/60Hz.

(5) The receiver must be operated for about 15 minutes priorto the adjustment.

O After RGB Full white HEAT-RUN Mode, the receiver mustbe operated prior to adjustment.

O Enter into HEAT-RUN MODE1) Press the POWER ON KEY on R/C for adjustment.2) OSD display and screen display 100% full WHITE

PATTERN.

[ Set is activated HEAT-RUN without signal generator inthis mode.

[ Single color pattern(RED/BLUE/GREEN) of HEAT-RUN mode uses to check PANEL.

Caution) If you turn on a still screen more than 20 minutes(Especially digital pattern, cross hatch pattern), a afterimage may be occur in the black level part of thescreen.

3. PCB assembly adjustment method

3-1. Channel memory

(1) Setting up the G-prove1) Install the GProve. (GProve4.4.0.2.exe)2) After installing the Gprobe, [Option -> Connection

Setup] or click the icon indicated in the picture and thensetup as below the picture.(In case of the port (second one), set to the serial port of the connected PCThe other only have to be set as below the picture.)

3) After finishing inputs, click the button [OK] to completethe connection setup.

(2) Confirming the G-prove1) Connect Rs232 cable and then turn on the power.

if communication is correct, the message is showed like in the left output terminal.

2) If the message is not showed, push the [INSTART]button of the adjust remocon twice, and change theright selection of the [System Control -> RS-232 Host]from GProbe to PC.** If it is impossible to check the OSD, push the [TILT]

button of the adjust remocon.Then, the message which is ÒStarting Gprove...Ó comes up. From this time, communication is operated correctly.However, you have to push the [TILT] button again in case of turning on Main Power.

** If you want to check again whether communication ison or not, input ÒtestÓ and push the Enter key on theright input terminal. If communication is on, themessage of ÒTest passed.Ó will come up

(3) Channel memory method1) Click [Command -> Batch].2) When the window of [Batch] is showed, enter the text file

(Ch_Memory-RZ_PX10.txt) in the right blank of the File.3) Click the button [OK] to write CH information in the

EEPROM.4) It means the completion of the CH memory download that

the message of right output terminal is showed as below.

ADJUSTMENT INSTRUCTIONS

fig1

fig2

fig3

3-2. HDCP download

(1) Setting up & Confirming the G-prove: refer to 3-1-(1) and 3-1-(2)

(2) HDCP download method1) Click [Command -> NVRAM Write]2) When the window of [NVRAM Write] is showed, select

ÒLGEKEY1.binÓ to insert fill up in the File.3) LGEKEY1 : first KEY value4) Address : insert Ô0Õ5) After finishing inputs, click the button [OK] to write

HDCP key in the EEPROM.6) It means the end of the HDCP key download that the

message of Output terminal is showed as below.

4. SET assembly adjustment method

4-1. POWER PCB Assy Voltage Adjustments(Va, Vs Voltage Adjustments)

(1) Test Equipment : D.M.M 1EA

(2) Connection Diagram for Measuring : refer to fig5

(3) Adjustment Method1) Adjustment method of P/No 3501V00180A B/D

1. Va Adjustmenta. After receiving 100% Full White Pattern, HEAT RUN.b. Connect + terminal of D.M.M to Va pin of P805,

connect - terminal to GND pin of P805.c. After turning RV 501, voltage of D.M.M adjustment

as same as Va voltage which on label of panelright/top (Deviation; ±0.5V)

2. Vs Adjustmenta. Connect + terminal of D.M.M to Vs pin of P805,

connect Ð terminal to GND pin of P805.b. After turning RV 401, voltage of D.M.M adjustment

as same as Va voltage which on label of panelright/top. (Deviation; ±0.5V)

2) Adjustment method of P/No 3501V00182A B/D1. Va Adjustment

a. After receiving 100% Full White Pattern, HEAT RUN.b. Connect + terminal of D.M.M to Va pin of P805,

connect - terminal to GND pin of P805.c. After turning RV 601, voltage of D.M.M adjustment

as same as Va voltage which on label of panelright/top (Deviation; ±0.5V)

2. Vs Adjustmenta. Connect + terminal of D.M.M to Vs pin of P805,

connect Ð terminal to GND pin of P805.b. After turning RV 401, voltage of D.M.M adjustment

as same as Va voltage which on label of panelright/top. (Deviation; ±0.5V)

4-2. Adjustment of White Balance

(1) Required EquipmentColor Analyzer (CA-100 or same product)

(2) Connection Diagram of Equipment for Measuring

(3) Adjustment of White BalanceO Operate the Zero-calibration of the CA-100, then stick

sensor to PDP module surface when you adjust.O For manual adjustment, it is also possible by the

following sequence.

- 16 -

fig4

< 3501V00180A >

< 3501V00182A >

fig5.connection Diagram of power adjustment for measuring

Each PCB Assy must be checked by the Check JIG Set beforewhole assembly. (Be careful the POWER PCB Assy not todamage to PDP Module)

Window

MSPG-2100 orMSTG-5200

AV Signal Input

Full Size pattern

216 gray Level

RS-232C Serial Communication

RZ/RT 50Hz

fig6 White Balance Adjustment

1) Select white pattern of heat-run mode by pressing poweron key on remote control for adjustment then operateheat run more than 15 minute.

2) Supply 2 Gray Pattern (216 Level Full Size Pattern)signal to VIDEO input.(RZ-42PX10 : AV4 INPUT 50Hz,RT-42PX10 : AV2 INPUT 50Hz)(refer to Fig6)

3) To adjust, stick sensor to 216 Gray Level Pattern, pressADJ key twice(White Balance) on remote control.For adjustment and D , E on remote control foradjustment mode to select Red Gain and Blue Gain,press VOL +, - Key and adjust it until color coordinationbecomes as below.

X ; 0.283 ± 0.003, Y; 0.297 ± 0.003,Color Temperature; 9,300¡K ± 500¡K

4) Exit adjustment mode using A Key.

4-3. Auto RGB Color Balance

(1) Pattern Equipment : PC Pattern Generator (VG828, VG854, 801GF, MSP3240A)(16 Gray Scale Pattern output(RGB output Level: 0.7Vp-p)

(2) Method of Auto RGB Color Balance 1) Input RGB Source : 16 Gray Scale Pattern output

(RGB output Level : 0.7Vp-p)2) Press ADJ KEY on R/C for adjustment. 3) Press Vol. + KEY and operate To set.4) Auto-RGB OK means completed adjustment.

4-4. Auto Component Color Balance

(1) Pattern Equipment : MSP3240A or same product(16 Gray Scale Pattern output(Component outputLevel: 0.7Vp-p)

(2) Method of Auto RGB Color Balance 1) Input RGB Source : Component 480p/576p 16 Gray

Scale Pattern outputAt this time, except Pb and Pr signal, only Y signal insert.2) Press ADJ KEY on R/C for adjustment. 3) Press Vol. + KEY and operate To set.4) Auto-RGB OK means completed adjustment

4-5. Auto Adjustment Map(RS-232C)

4-6. DDC Data Input(1) Required Test Equipment

1) A jig for adjusting PC, DDC (PC serial to D-subConnection equipment)

2) S/W for writing DDC (EDID Data Write & Read)3) D-sub 15P Cable, D-Sub to DVI Connector (Connect to DVI Jack)

(2) Setting of Device

(3) Preparation for Adjustment1) Set devices as above and turn the PC, jig on.2) Put S/W for writing DDC (EDID data Write & Read) into

operation. (operated in DOS mode.)

(4) Sequence of Adjustment1) DDC Data Input for Analog-RGB

1. Put the set on the table and turn the power on.2. Connect PC Serial to D-sub 15P Cable of jig for DDC

adjustment to RGB terminal (D-Sub 15Pin).3. Operate S/W for DDC record and select DDC data for

Analog RGB in Model Menu.4. Operate EDID Write command.5. Operate EDID Read command and check whether

Check Sum is 53.6. If Check Sum is not 53, repeat 3 ~ 4.7. If Check Sum is 53, DDC data for Analog-RGB input

is completed.

2) DDC Data input for Digital-RGB(DVI)1. Connect PC Serial to DVI Cable of jig for DDC

adjustment to DVI terminal (DVI Jack).2. Operate S/W for DDC record and select DDC Data

for digital RGB in Model Menu.3. Operate EDID Write command. 4. Operate EDID Read command and check whether

Check Sum is D2(1page), BF(2page).5. If Check Sum is not D2(1page), BF(2page), repeat 3 ~ 4.6. If Check Sum is D2(1page), BF(2page), DDC data for

Analog-RGB input is completed.

- 17 -

fig7 Auto RGB/Component Color Balance Test Pattern

Type

Baud Rate

115200

Index

R Gain

G Gain

B Gain

R Offset

G Offset

B Offset

Data bit

8

Cmd1 Cmd2

j a

j b

j c

j d

j e

j f

Stop bit

1

Parity

NONE

ProtocolSetting

Data Min Value

00(00)

00(00)

00(00)

00(00)

00(00)

00(00)

Max Value

255(FF)

255(FF)

255(FF)

255(FF)

255(FF)

255(FF)

RF-043B_PDP42

PCPC

JIGJIG

PDPPDP

SETSET

- 18 -

TROUBLE SHOOTING GUIDE

1. Power Board

1-1. The whole flowchart which it follows in voltage output state

Start check

Manufacture enterprisemeaning of a passage

1. Check the Power Offcondition.

Doesn't the screen whole come

out?

It is identical with Power Off

condition?

Yes

Yes

No

No

No

No

No

2. Check the Interfacesignal condition.

Is the Interface signal operated?

Yes

3. Check the St-by 5Vsignal circuit.

Doesn't the low pressure output

come out?

Doesn't the St-by 5V signal

come out?

Yes

Yes

No

4. Check the 5V Monitorsignal circuit.

Doesn't the 5V Monitor signal

come out?

Yes

7. Check the VSC Vs-ONsignal

Doesn't the high tension output

come out?

Doesn't the VSC signal Vs-ON

come out?

Yes

Yes

High tension output voltage Drop

it occurs?

When remove the

Y B/D Module Input Connector, output

voltage Drop it occurs?

When remove the Y, Z B/D Module

Input Connector, Power Board high tension output


Yes No No

9. Check the PowerBoard Output high

tension circuit

Yes

10. Check the Z B/DModule Coutput circuit

Yes

When remove the

Z B/D Module Input Connector, output


11. Check the Y B/DModule Coutput circuit

Yes

No

8. Check the Vs, Vavoltage output circuit.

Doesn't the Vs, Va voltage output

come out?

Yes

No

No

5. Check the VSC RL-ONsignal.

Doesn't the VSC signal RL-ON

come out?

Yes

6. Check the VSC lowpressure output

Doesn't the VSC low pressureoutput come out?

Yes

- 19 -

1-2. Sony Power Board Structure

T502: Vs Trans

T702: Va Trans

T101: St-by Trans

T103: Low Voltage Trans

1 2 3

- 20 -

1-3. Sanken Power Board Structure

T221: Vs Trans

T271: Va Trans

T121: St-by Trans

T201: Low Voltage Trans

1 2 3

- 21 -

2. No Power

(1) Symptom¯ DoesÕt minute discharge at module. ¯ Non does not come in into the front LED.

(2) Check follow

Is plug in power cord? Plug in power cord.

Yes

No

Is connect the Line Filter and PowerSwitch Cable?

Connect Cable.

Yes

No

Is connect the Power Switch andPower Board Cable?

Connect Cable.

Yes

No

Is normal the Fuse(F101) on PowerBoard?

Replace Fuse.

Yes

No

Is connect the Power Board and 7Pof VSC Board Cable?

Connect Cable.

Yes

No

Is connect the Power Switch andPower Board Cable?

After remove the cable connect toPower Board(except the CN101

connection cable), authorizes theAC voltage marking on manual.

When ST-BY 5V does not operate,replace Power Board.

Connect Cable.

Yes

No

- 22 -

3. Protect Mode

(1) Symptom¯ After once shining, it does not discharge minutely

from module¯ The Rely falls(The sound is audible ÒclickÓ) ¯ It is converted with the color where the front LED

is red from green.

(2) Check follow

Is normal the PowerBoard?

Replace PowerBoard.

Is output the normality Low/Highvoltage except Stand-by 5V?

Yes

No No

Is normal the eachconnector?

Replaceconnector.

Replace Y-Board.

After connecting well each connector,the normality it operates?

Yes

No No

Is normal the Ctrl Board?

Replace X-Board.

Is normal the output voltage afterremove P1, 2, 101, 300, 701, 702

connector of Ctrl-B/D?

Yes

No Yes

Is normal the Y- Board?

Is normal the outputvoltage after removeP5, P6 connector of

Y-B/D?

Is normal the Fuse(F52) on Y-B/D?(In case of open is replace)

Yes

No Yes Yes

Replace Z-Board.

Is normal the Z- Board?

Is normal the outputvoltage after remove

P1 connector of Z-B/D?

Is normal the Fuse(FS1, FS2) on Z-B/D? (In case of open is replace)

Yes

No Yes

Is normal the X- Board?

Is normal the output voltage afterremove P1, 2, 3, 4, 6, 7 connector of

X-B/D?

After remove P1, P2, P3, P4 output voltagenormality: Replace Right X-B/DAfter remove P6, P7 output voltagenormality: Replace Left X-B/D

Yes

No Yes

Is normal the VSC Board?

Is normal the output voltage afterremove P1000, P1200?

After crisis COF of each board, check the normality operates.If in case normality operates, correspondence COF Fail isreplace the module.

After remove P1000 normal operation:Replace Analog BoardAfter remove P1200 normal operation:Replace Digital Board

Yes

No

Is normal the COF of X, Y, Z?

No

Yes

Yes

- 23 -

4. No Raster

(1) Symptom¯ DoesÕt minute discharge at module. ¯ It maintains the condition where the front LED is green.

(2) Check follow

Is normal the PowerBoard?

Replace PowerBoard.

Is output the normality Low/Highvoltage except Stand-by 5V?

Yes

No No

Is normal the eachconnector?

Replaceconnector.

Replace Y-Board.

After connecting well each connector,the normality it operates?

Yes

No No

Is normal the Ctrl Board?

Replace X-Board.

Is normal the output voltage afterremove P1, 2, 101, 300, 701, 702

connector of Ctrl-B/D?

Yes

No Yes

Is normal the Y- Board?

Is normal the outputvoltage after removeP5, P6 connector of

Y-B/D?

Is normal the Fuse(F52) on Y-B/D?(In case of open is replace)

Yes

No Yes Yes

Replace Z-Board.

Is normal the Z- Board?

Is normal the outputvoltage after remove

P1 connector of Z-B/D?

Is normal the Fuse(FS1, FS2) on Z-B/D? (In case of open is replace)

Yes

No Yes

Is normal the X- Board?

Is normal the output voltage afterremove P1, 2, 3, 4, 6, 7 connector of

X-B/D?

After remove P1, P2, P3, P4 output voltagenormality: Replace Right X-B/DAfter remove P6, P7 output voltagenormality: Replace Left X-B/D

Yes

No Yes

Is normal the VSC Board?

Is normal the output voltage afterremove P1000, P1200?

After crisis COF of each board, check the normality operates.If in case normality operates, correspondence COF Fail isreplace the module.

After remove P1000 normal operation:Replace Analog BoardAfter remove P1200 normal operation:Replace Digital Board

Yes

No

Is normal the COF of X, Y, Z?

No

Yes

Yes

- 24 -

5. In case of occur strange screen into specific mode

5-1. In case of doesÕt display the OSD

(1) Symptom¯ LED is green¯ The minute discharge continuously becomes

accomplished from module

(2) Check follow

Is normal the LVDScable?

Is normal the VSCDigital Board?

Is the LVDS cableconnected well?

Cable inserts well.Yes

No

No

Yes

Operates the ThineIC(IC1100)?

Replace ThineIC(IC1100).

No

Is normal the CtrlBoard of Module?

Replace Ctrl B/D.No

No

Operates theIEP(IC500)?

ReplaceIEP(IC500).

Yes

No

Operates theScaler(IC700)?

ReplaceScaler(IC700).

Yes

Replace cable.Yes

- 25 -

5-2. In case of doesÕt display the screen into specific mode

(1) Symptom¯ The screen does not become the display from specific input mode

(RF, AV, Component, RGB, DVI).

(2) Check follow¯ Check the all input mode should become normality display.¯ Check the Video(Main)/Data(Sub), Video(Main)/Video(Sub) should become

normality display from the PIP mode or DW mode. (Re-Check it Swap)

(3) In case of becomes unusual display from RF mode

(4) In the case of becomes unusual display from RF, AV mode

Is normal the Tuner?

Is normal theCXA2069Q?

Is the Tuner Cableconnected well?

Cable inserts well.

Yes

No

No

Yes

Is normal theVPC3230?

Replace Tuner

No

Is normal the Input voltage, IICCommunication and CVBS output?

Yes

Is normal the Input voltage, IICCommunication and HV sync?

NoReplace IC

No


NoReplace IC

No

Is normal theCXA2069Q?

Yes



NoReplace IC

No


NoReplace IC

No

- 26 -

(5) In the case of becomes unusual display from RF, AV, Component 480i mode

(6) In the case of becomes unusual display from Component DTV mode


Yes

Is normal the S2300?


NoReplace IC

No


NoReplace IC

No

Yes

Is normal the Scaler?Is normal the Input voltage, IICCommunication and HV sync?

NoReplace IC

No

Is normal the74LS123?

Yes

Is normal theCXA2101?


NoReplace IC

No


NoReplace IC

No

Yes

Is normal theM52758?


NoReplace IC

No

Yes


NoReplace IC

No

- 27 -

(7) In the case of becomes unusual display from RGB DTV mode

(8) In the case of becomes unusual display from RGB PC mode

(8) In the case of becomes unusual display from DVI mode

Is normal theCXA2101?

Yes



NoReplace IC

No


NoReplace IC

No


Yes

Is normal the Scaler?


NoReplace IC

No


NoReplace IC

No


NoReplace IC

No

Yes


NoReplace IC

No

- 28 -

6. In case of no sound

(1) Symptom¯ LED is green¯ Screen display but sound is not output

(2) Check follow

Is normal the SPKcable?

Is the SPK cableconnected well?

Cable inserts well.

No

No

Cable inserts well.

No

Replace IC800

No

Replace IC801

No

Replace SPK cableYes

Yes

Is normal theRGB/DVI sound?

Is the Flat cableconnected well?

No

No

Operates the IC800?Yes

Operates the IC801?

Replace IC802

No

Operates the IC802?Replace

VSC Analog B/D

Yes

Yes

Yes

Is normal theRF/AV/Component

sound?

- 29 -

BLOCK DIAGRAM

RG

B( P

C/D

TV)

DV

I( P

C/D

TV)

RS

23

2

IR

74A

CT

253

RX

0/1

,TX

0/1

IRTX

SC

L/S

DA

RG

B H

/V

SC

L/S

DA

RX

/TX

0/1

/2,

RX

/TX

C

ST

32

32

C

24L

C2

1

74

HC

T0

8

24

LC

21

CX

A2

10

1

Sca

rt1

Sca

rt2

Sca

rt3

RF

CV

BS

S-V

HS

CX

A2

06

9Q

SW

ITC

HT

un

er (

M)

Tu

ne

r(S

)

Vin

1 ( C

VB

S)

VP

C3

23

0 ( M

)V

ide

o D

eco

der

VP

C3

23

0 ( S

)V

ide

o D

ecod

er

1H R

GB

Vin

2 ( C

VB

S)

MN

T O

UT

TV

OU

T

Vin

3 ( C

VB

S) T

U_M

ain

TU

_Su

b

Vin

4

YC

in4

Ma

in_V

Ma

in_Y

C

Ma

in_V

Ma

in_Y

C S

DA

60

01

Text

Pro

cess

or

Te

xt_V

HY

V6

41

62

0S

RA

M

AM

29

LV

16

0F

-RO

M

74L

S1

23

Co

mp

_48

0i

M5

27

58

FS

wit

ch

S2

30

0D

eIn

terl

ac

er

YC

bC

r/ 8

HY

57

V6

43

22

SD

RA

M (

8M

B)

RG

B P

C/D

TV

RG

B P

C

RG

B D

TV

gm

16

01

Sc

ale

r (M

ali

bu

)C

omp

DT

V

CX

A_R

GB

RG

B_D

ata

Ma

in_V

ide

o / 24

Su

b_V

ide

o/ 8

DV

I_D

ata

TX

_Ou

t

RS

23

2_R

X/T

X

Co

mp

/RG

B_S

WF

rom

Ma

lib

u

Dig

ita

l

An

alo

g

Sid

e-A

V

CV

BS

S-V

HS

Vin

5Y

Cin

5C

om

p_Y

Co

mp

_48

0I/

PT

o M

ali

bu

Vid

eo

fo

r T

ext

Te

xtT

X0

/1/2

/3/C

Dis

p_E

nS

DA

TA

SC

LK

, S

LE

HY

5D

U2

83

22

2A

SD

RA

M (

12

8M

B)

AM

29

LV

F-R

OM

(1

MB

)

Co

mp

/RG

B_S

W

Co

mp

_48

0I/

P

Po

st-p

roc

es

sin

g B

loc

k is

om

itte

d.

so-

ca

lle

d J

EP

ICO

, in

th

is c

as

eT

MD

S T

X i

s a

lso

re

qu

ire

d.

So

un

d P

roc

es

sin

g B

loc

k D

iag

ram

is s

ep

ara

ted

..R

CA-

typ

e B

loc

k D

iag

ram

is

als

o

se

pa

rate

d..

DV

I R

Xw

/HD

CP

AD

Cw

/PL

L

IEP

24

24

24

24 1

0

WIR

E

ZH

INE

Co

mp

1( D

D/ D

TV

)V

BO

AR

D

BO

AR

D

BO

AR

D

BLOCK DIAGRAM

- 30 -

RG

B(P

C/D

TV

)

DV

I(P

C/D

TV

)

RS

23

2

IR

ST

32

32

C

74A

CT

25

3

74H

CT

08

Tx

gm

15

01

H2

4LC

21

24L

C2

1

RG

B P

C

IIS IIS

IIS

CX

A2

10

1C

XA

21

01

RG

B D

TV

HV

M5

27

58

FP

IC2

02

(MU

X)

M5

27

58

FP

IC2

02

(MU

X)

M5

27

58

FP

IC2

04

M5

27

58

FP

IC2

04

RG

B_D

TV

FL

I23

00

FL

I23

00

HY

57

V6

43

22

SD

RA

M (

8M

B)

HY

57

V6

43

22

SD

RA

M (

8M

B)

DA

C_R

GB

Co

mp

1( D

VD

/DT

V)

RF

CV

BS

IN

Sid

e

S-V

HS

An

alo

g

CV

BS

OU

T

Sid

e-C

VB

S

Co

mp

2( D

VD

/DT

V)

TQ

FP

12

8K

DD

R M

em

ory

TQ

FP

12

8K

DD

R M

em

ory

Fla

sh

RO

M5

12

K/1

MF

las

h R

OM

51

2K

/1M M

62

32

0F

P(I

2C

Exp

en

de

r)

M6

23

20

FP

(I2

C E

xpe

nd

er)

CX

A2

06

9Q

UP

D6

40

83

UP

D6

40

83

VP

C3

23

0 (M

AIN

)V

PC

32

30

(MA

IN)

VP

C3

23

0 (S

UB

)V

PC

32

30

(SU

B)

DV

D_S

UB

DT

V_C

om

p

M5

27

58

FP

IC4

00

(MU

X)

M5

27

58

FP

IC4

00

(MU

X)

DV

D_M

AIN

DV

D2

_MA

IN

DV

D2

_SU

B

DT

V2

_Co

mp

S-V

HS

Tu

ne

r (M

)

Tu

ne

r (S

)

VIN

1

Y/C

IN1

Co

mp

Co

mp

2

MN

T_O

UT

VIN

2

Y/C

IN2

MA

IN_V

OU

T

SU

B_C

OU

T

SU

B_Y

OU

T

CA

B_V

IN

MA

IN_Y

OU

T

MA

IN_C

OU

T

LA

71

51

MS

W C

VB

S/Y

CO

MB

_YO

UT

CO

MB

_CO

UT

AL

T_Y

_48

0I_

MA

IN

AL

T_Y

_48

0I_

SU

B

AL

T_Y

2_4

80

I_M

AIN

AL

T_Y

2_4

80

I_S

UB

S/D

VD

_Co

mp

M3

71

36

(OT

P)

M3

71

36

(OT

P)

CA

B_C

om

b

MA

IN_Y

OU

T

M6

56

8 B

it

S6

56

8 B

it

Sid

e A

/V

TM

DS

Tra

ns

fer

/Th

ine

LV

DS

31

PIN

RG

B_2

4B

it

An

alo

g

RG

B

DV

I

VP

OR

T(2

4b

it)

SV

PO

RT

(16

bit

)

IEP

ZH

INE

WIR

E

Dig

talB

OA

RD

BO

AR

D

MEMO

- 31 -

- 32 -

EXPLODED VIEW

300

301

304

302

202206

203

204

201

205

580

400

401#

410

402

520

560

530

531

570

121

601600

120

490

207

200

303

305

- 33 -

120 6401VD0013B SPEAKER ASSEMBLY, FULL RANGE(L) . RZ-42PX10 L

121 6401VD0013A SPEAKER ASSEMBLY, FULL RANGE(R) . RZ-42PX10 R

200 6348Q-E050C PDP, 42Ó 16:9 852*480 PDP42V60000.AKLGG

201 6871QCH034A PWB(PCB) ASSEMBLY,DISPLAY CTRL ASSY HAND INSERT 42V6 NEW MCM(1222) LVDS

202 6871QDH066A PWB(PCB) ASSEMBLY,DISPLAY YDRV ASSY HAND INSERT 42V6 YDRV TOP HAND INSERT ASSY

203 6871QDH067A PWB(PCB) ASSEMBLY,DISPLAY YDRV ASSY HAND INSERT 42V6 YDRV BTM HAND INSERT ASSY

204 6871QLH034A PWB(PCB) ASSEMBLY,DISPLAY XRLT ASSY HAND INSERT 42V6_XL(4LAYER)

205 6871QRH037A PWB(PCB) ASSEMBLY,DISPLAY XRRT ASSY HAND INSERT 42V6_XR(4LAYER)

206 6871QYH029A PWB(PCB) ASSEMBLY,DISPLAY YSUS ASSY HAND INSERT 42V6

207 6871QZH033A PWB(PCB) ASSEMBLY,DISPLAY ZSUS ASSY HAND INSERT 42V6

300 3091V00645A CABINET ASSEMBLY, RZ-42PY20

301 4980V01067A SUPPORTER, ASSY AL FILTER TOP RZ-42PZ10

302 4980V01068A SUPPORTER, ASSY AL FILTER BOTTOM RZ-42PX10

303 4980V01069A SUPPORTER, ASSY AL FILTER RIGHT RZ-42PX10

304 4980V01070A SUPPORTER, ASSY AL FILTER LEFT RZ-42PX10

305 3790V00281G FILTER(MECH), RZ-42PX10 NBK 1142G03EK-M6 AR/NIR MESH GLASS 3 LAYER

400 3809V00444A BACK COVER ASSEMBLY RZ-42PY20

401 3301V00025D PLATE ASSEMBLY, ASSY COVER VSC TUNER RU-42PX10 PRESS

402 3301V00023D PLATE ASSEMBLY, ASSY AV VSC TUNER RU-42PX10

410 4980V01071A SUPPORTER, ASSY AL MODULE. RZ-42PX10

490 4980V01057A SUPPORTER, PCB EGI POWER SW. RZ-42PY20

520 6871VMMS17A PWB(PCB) ASSEMBLY,MAIN RF043B MALIBU RT MAIN DIGITAL MANUAL

530 6871VSME92A PWB(PCB) ASSEMBLY,SUB PSW RF043A MAILBU

531 5020V00915A BUTTON, POWER RZ-42PY20 ABS 1KEY .

560 6871VSMS05A PWB(PCB) ASSEMBLY,SUB TUNER RF043B MALIBU RT SUB ANALOG MANUAL

570 6871VSMZ91A PWB(PCB) ASSEMBLY,SUB CONT RF043A NEW HOLDER LOCAL KEY KODENSI

580 3501V00180A BOARD ASSEMBLY, POWER RZ-42PX10 RF043A 1H201W1 SANKEN PSU

600 6871VSME91A PWB(PCB) ASSEMBLY,SUB A/V RF043A MALIBU SIDE AV

601 4811V00118B BRACKET ASSEMBLY, DECO RU-42PX10 RF043A SIDE AV

EXPLODED VIEW PARTS LIST

No. Part No. Description

M62320FP,I/O EXPANDER 16P SOP TP

AT24C02N-10SI-2.7 ATMEL 8P SOIC

KA7809R, FAIRCHILD 2P D-PAK

MIC39100 MICREL 3P SOT223

PQ05DZ1U SHARP 5, SMD TYPE

TK11840L 8P SOT23L


AT24C02N-10SI-2.7 ATMEL 8P SOIC

SN74HCT08D TEXAS INSTRUMENT 16P

SN74LVTH541PWR 20P TSSOPUT

SN74LVTH541PWR 20P TSSOPUT

THC63LVD103 64P TQFP

SC1565IST-1.8 SEMTECH 3P SOT223 TP

MIC39100 MICREL 3P SOT223

KA7809R, FAIRCHILD 2P D-PAK

BA033FP-E2 ROHM 3P-SOP,TO252-3




SC1565IST-1.8 SEMTECH 3P SOT223 TP


MIC39100 3P SOT223 R/TP LDO TYPE 2.5V

74ACT253SC FAIRCHILD 16P SOIC

ST3232CDR SGS-THOMSON SOP16

M52758FP MITSUBISHI 36PIN

DM74LS123MX 16SOP TP

DM74LS123MX 16SOP TP

CXA2069Q QFP64 BK I2C BUS AV S/W

CXA2101AQ 80P,QFP BK

SN74HCT08D 16P R/TP QUADRUPLE

LGDT4410 LG IC 176P TQFP

SDA6001 QH B12 128P MQFP

HY57V641620HGT-H HYNIX 54P TSOPII

MX29LV160ATTC-70 MACRONIX 48P TSOP

AT24C16AN-10SI-2.7 ATMEL 8P SOIC

KIA7027AF 3, SOT-89 TP RESET IC 2.7V

FLI2300BD GENESIS 208P PQFP

M52758FP MITSUBISHI 36PIN, R/TP PLL IC

VPC3230D C5 80P QFP

HY57V643220C(L)T-6 HYNIX 86P TSOP

VPC3230D C5 80P QFP

GM1501HBD GENESIS 416P PBGA

AT24C32AN-10SI-2.7 8PIN SOP TP 32K 3.3V

KIA7042AF SOT-89 TP 4.2V

MSP4410G-QA-C13-101

HY5DU283222AQ-5 HYNIX 100P LQFP

NSP-6241B NEOFIDELITY 64P TQFP

MX29LV800TTC-70 48PIN,TSOP

TAS5122DCAR 56P/TSSOP

KIA7042AF SOT-89 TP 4.2V

REPLACEMENT PARTS LIST

LOCA. NO PART NO DESCRIPTION

Q001

Q002

Q100

Q100

Q1000

Q101

Q101

Q102

Q102

Q103

Q103

Q104

Q105

Q106

Q107

Q108

Q110

Q111

Q1200

Q1201

Q1202

Q207

Q208

Q209

Q210

Q211

Q214

Q215

Q216

Q217

Q218

Q219

Q300

Q301

Q302

Q303

Q304

Q305

Q306

Q307

Q308

Q309

Q310

Q311

Q312

Q313

Q314

Q315

Q316

Q317

Q318

0TR387500AA

0TR387500AA

0TR150400BA

0TR830009BA

0TRKE80038A

0TR387500AA

0TR830009BA

0TR387500AA

0TR830009BA

0TR150400BA

0TR830009BA

0TR387500AA

0TR387500AA

0TR150400BA

0TR387500AA

0TR150400BA

0TR830009BA

0TR830009BA

0TR387500AA

0TR387500AA

0TR387500AA

0TR387500AA

0TR387500AA

0TR150400BA

0TR387500AA

0TR104009AF

0TR387500AA

0TR150400BA

0TR104009AF

0TR387500AA

0TR387500AA

0TR387500AA

0TR387500AA

0TR387500AA

0TR387500AA

0TR387500AA

0TR387500AA

0TR387500AA

0TR387500AA

0TR387500AA

0TR387500AA

0TR387500AA

0TR387500AA

0TR387500AA

0TR387500AA

0TR387500AA

0TR387500AA

0TR387500AA

0TR387500AA

0TR387500AA

0TR387500AA

CHIP 2SC3875S(ALY) KEC


CHIP 2SA1504S(ASY) KEC

BSS83 TP PHILIPS N-CHANNEL S/W TR

KTC3552T-RTK KEC R/TP SOT-23F 50V 3A





















CHIP KRC104S SOT-23 TP KEC



CHIP KRC104S SOT-23 TP KEC
























IC100

IC100

IC1000

IC1001

IC1002

IC1003

IC1004

IC101

IC102

IC103

IC104

IC1100

IC1200

IC1201

IC1202

IC1300

IC1301

IC1302

IC1303

IC1304

IC1305

IC1306

IC200

IC201

IC202

IC203

IC204

IC400

IC401

IC402

IC500

IC500

IC501

IC502

IC503

IC504

IC600

IC600

IC601

IC601

IC700

IC700

IC701

IC702

IC800

IC800

IC801

IC801

IC802

IC805

0IMI623200B

0IMMRAL014B

0IMCRFA010A

0IPRPML001A

0IMCRSH001A

0ITK118100B

0IMCRSH001A

0IMMRAL014B

0IMCRTI003A

0IMCRTI021A

0IMCRTI021A

0IMCRTH002A

0IMCRSJ001A

0IPRPML001A

0IMCRFA010A

0IMCRRH001A

0IMCRSH001A

0IMCRSH001A

0IMCRRH001A

0IMCRSJ001A

0IMCRRH001A

0IPRPML001A

0IFA742530B

0IMCRSG010A

0IMCRMI006A

0IFA741230A

0IFA741230A

0ISO206900A

0ISO210100B

0IMCRTI003A

0ICTMLG018A

0IMCRMN023A

0IMMRHY001F

0IMMRMR006B

0IMCRAL006A

0IKE702700D

0IMCRGN002C

0IMCRMI006A

0IIT323000E

0IMMRHY033A

0IIT323000E

0IPRPGN012A

0IMMRAL025A

0IKE704200J

0IMCRMN028A

0IMMRHY020B

0IMCRNL001A

0IMMRMR023A

0IMCRTI028C

0IKE704200J

IC TRANSISTOR

- 34 -

- 35 -


Q319

Q320

Q321

Q400

Q400

Q401

Q401

Q402

Q402

Q403

Q404

Q405

Q406

Q600

Q800

Q801

Q802

D100

D100

D1000

D1001

D1002

D1003

D1004

D101

D101

D102

D103

D104

D105

D116

D117

D118

D119

D120

D1200

D1201

D1206

D121

D122

D123

D124

D125

D126

D127

D128

D129

D130

D1300

D1301

0TR387500AA

0TR387500AA

0TR387500AA

0TR150400BA

0TR387500AA

0TR150400BA

0TR387500AA

0TR150400BA

0TR387500AA

0TR387500AA

0TR387500AA

0TR387500AA

0TR387500AA

0TR387500AA

0TR387500AA

0TR387500AA

0TR387500AA

0DD226239AA

0DD226239AA

0DD226239AA

0DD184009AA

0DD226239AA

0DD226239AA

0DD226239AA

0DD226239AA

0DD226239AA

0DD226239AA

0DD226239AA

0DD226239AA

0DD184009AA

0DD226239AA

0DD226239AA

0DD226239AA

0DD226239AA

0DD226239AA

0DD226239AA

0DD226239AA

0DD226239AA

0DD226239AA

0DD226239AA

0DD226239AA

0DD226239AA

0DD226239AA

0DD226239AA

0DD226239AA

0DD226239AA

0DD226239AA

0DD226239AA

0DD226239AA

0DD226239AA


















CHIP KDS226 SOT-23

CHIP KDS226 SOT-23

CHIP KDS226 SOT-23

KDS184S CHIP 85V 300MA KEC TP

CHIP KDS226 SOT-23

CHIP KDS226 SOT-23

CHIP KDS226 SOT-23

CHIP KDS226 SOT-23

CHIP KDS226 SOT-23

CHIP KDS226 SOT-23

CHIP KDS226 SOT-23

CHIP KDS226 SOT-23

KDS184S CHIP 85V 300MA KEC TP

CHIP KDS226 SOT-23

CHIP KDS226 SOT-23

CHIP KDS226 SOT-23

CHIP KDS226 SOT-23

CHIP KDS226 SOT-23

CHIP KDS226 SOT-23

CHIP KDS226 SOT-23

CHIP KDS226 SOT-23

CHIP KDS226 SOT-23

CHIP KDS226 SOT-23

CHIP KDS226 SOT-23

CHIP KDS226 SOT-23

CHIP KDS226 SOT-23

CHIP KDS226 SOT-23

CHIP KDS226 SOT-23

CHIP KDS226 SOT-23

CHIP KDS226 SOT-23

CHIP KDS226 SOT-23

CHIP KDS226 SOT-23

CHIP KDS226 SOT-23


D1302

D1303

D1304

D1305

D1306

D131

D200

D201

D202

D203

D204

D205

D500

D501

D502

D503

LD001

LD1000

LD1001

LD1002

LD1003

LD1203

LD1204

LD1206

LD1207

ZD100

ZD101

ZD102

ZD103

ZD104

ZD105

ZD400

ZD401

ZD800

C002

C1001

C1002

C1003

C1004

C1006

C1016

C1017

C1018

C102

C1020

C1022

C1025

C1027

C1031

C1037

0DD226239AA

0DD226239AA

0DD226239AA

0DD226239AA

0DD226239AA

0DD226239AA

0DD226239AA

0DD226239AA

0DD226239AA

0DD226239AA

0DD226239AA

0DD226239AA

0DD226239AA

0DD226239AA

0DD226239AA

0DD226239AA

0DL200000CA

0DL233309AC

0DL233309AC

0DL233309AC

0DL233309AC

0DL233309AC

0DL233309AC

0DL233309AC

0DL233309AC

0DR050008AA

0DR050008AA

0DR050008AA

0DR050008AA

0DR050008AA

0DR050008AA

0DR050008AA

0DR050008AA

0DZ820009AH

0CE4763F618

0CE107SF6DC

0CE227VF6DC

0CE107SF6DC

0CE475SK6DC

0CE477SF6DC

0CE107SF6DC

0CE107SF6DC

0CE107SF6DC

0CE475SK6DC

0CE107SF6DC

0CE477SF6DC

0CE475SK6DC

0CE107SF6DC

0CE477SF6DC

0CE477SF6DC

CHIP KDS226 SOT-23

CHIP KDS226 SOT-23

CHIP KDS226 SOT-23

CHIP KDS226 SOT-23

CHIP KDS226 SOT-23

CHIP KDS226 SOT-23

CHIP KDS226 SOT-23

CHIP KDS226 SOT-23

CHIP KDS226 SOT-23

CHIP KDS226 SOT-23

CHIP KDS226 SOT-23

CHIP KDS226 SOT-23

CHIP KDS226 SOT-23

CHIP KDS226 SOT-23

CHIP KDS226 SOT-23

CHIP KDS226 SOT-23

LED,SAM5670(DL-2LRG) BK Y-GREEN -

LED,SAM2333 GREEN/RED GREEN:10MCD, RED:6MCD








SD05.TC R/TP SEMTECH SOD323 5V 5A 15A








MTZJ8.2B TP ROHM-K DO34 - 8.2V 5UA -

47UF SRE 16V M FL TP5

100UF MVG 16V M SMD R/TP

220UF MV 16V 20% R/TP(SMD) SMD


4.7UF MVG 50V 20% SMD R/TP

470UF MVG 16V 20% R/TP(SMD) SMD











DIODE

CAPACITOR

For Capacitor & Resistors,the charactors at 2nd and 3rddigit in the P/No. means asfollows;

CC, CX, CK, CN : CeramicCQ : PolyestorCE : Electrolytic

RD : Carbon FilmRS : Metal Oxide FilmRN : Metal FilmRF : Fusible

- 36 -


C104

C1041

C1042

C1045

C1046

C105

C1052

C1058

C1059

C106

C1060

C1061

C1063

C1066

C1066

C1067

C107

C1072

C1074

C1077

C1079

C108

C1082

C110

C111

C112

C113

C114

C120

C1202

C1205

C1206

C121

C121

C1211

C1212

C1215

C1216

C1218

C1220

C1229

C1233

C124

C1249

C1250

C1251

C1254

C1256

C1257

C1259

C127

C1273

0CE476DF618

0CE107SF6DC

0CE477SF6DC

0CE107SF6DC

0CE107SF6DC

0CE476DF618

0CE107SF6DC

0CE107SF6DC

0CE477DJ618

0CE227VF6DC

0CE227VF6DC

0CE107SF6DC

0CE227VF6DC

0CE107SF6DC

0CE476SF6DC

0CE477DJ618

0CE477SF6DC

0CE107SF6DC

0CE107SF6DC

0CE107SF6DC

0CE107SF6DC

0CE477SF6DC

0CE107SF6DC

0CE227VF6DC

0CE475SK6DC

0CE477SF6DC

0CE106SF6DC

0CE475SK6DC

0CE476SF6DC

0CE476SF6DC

0CE107SF6DC

0CE477SF6DC

0CE476SF6DC

0CE477SF6DC

0CE477SF6DC

0CE477SF6DC

0CE477SF6DC

0CE227VF6DC

0CE477SF6DC

0CE227VF6DC

0CE227VF6DC

0CE477SF6DC

0CE107SF6DC

0CE227VF6DC

0CE227VF6DC

0CE477SF6DC

0CE227VF6DC

0CE227VF6DC

0CE227VF6DC

0CE227VF6DC

0CE475SK6DC

0CE476SF6DC

47UF STD 16V M FL TP5








470UF STD 35V 20% FL TP 5







470UF STD 35V 20% FL TP 5






































C1274

C1275

C1279

C1305

C1314

C1315

C1317

C1331

C1333

C1353

C1355

C1362

C1366

C1368

C1373

C1374

C1384

C1388

C1391

C1400

C1402

C1404

C1410

C1415

C1425

C208

C209

C210

C222

C222

C223

C223

C224

C224

C230

C251

C254

C258

C261

C263

C272

C274

C276

C288

C289

C300

C301

C303

C315

C316

C317

C322

0CE107SF6DC

0CE107SF6DC

0CE107SF6DC

0CE107SF6DC

0CE476SF6DC

0CE107SF6DC

0CE107SF6DC

0CE477SF6DC

0CE477SF6DC

0CE477SF6DC

0CE477SF6DC

0CE107SF6DC

0CE227VF6DC

0CE227VF6DC

0CE107SF6DC

0CE476SF6DC

0CE476SF6DC

0CE476SF6DC

0CE477SF6DC

0CE476SF6DC

0CE476SF6DC

0CE477SF6DC

0CE477SF6DC

0CE477SF6DC

0CE107SF6DC

0CE106SF6DC

0CE477SF6DC

0CE106SF6DC

0CE476SF6DC

0CE476XFKDC

0CE476SF6DC

0CE476XFKDC

0CE476SF6DC

0CE476XFKDC

0CE107SF6DC

0CE106SF6DC

0CN105EJ56A

0CE476SF6DC

0CE476SF6DC

0CE476SF6DC

0CE107SF6DC

0CE107SF6DC

0CE107SF6DC

0CE106SF6DC

0CN105EJ56A

0CE476SF6DC

0CE476SF6DC

0CE476SF6DC

0CE476SF6DC

0CE476SF6DC

0CE476SF6DC

0CE476SF6DC






























47UF MVK-BP,CN 16V 20%,-20%


47UF MVK-BP,CN 16V 20%,-20%


47UF MVK-BP,CN 16V 20%,-20%



1.0UF 3216 35V 10% R/TP X7R








1.0UF 3216 35V 10% R/TP X7R











- 37 -


C324

C334

C335

C400

C401

C402

C404

C406

C410

C423

C429

C435

C440

C442

C502

C505

C506

C507

C508

C509

C517

C520

C522

C523

C525

C527

C529

C534

C601

C605

C607

C608

C611

C612

C614

C626

C627

C632

C634

C637

C651

C702

C703

C710

C713

C720

C723

C727

C737

C744

C752

C757

0CE476SF6DC

0CE476SF6DC

0CE476SF6DC

0CE227VF6DC

0CE476SF6DC

0CE107SF6DC

0CE227VF6DC

0CE476SF6DC

0CE107SF6DC

0CE105SK6DC

0CE107SF6DC

0CE107SF6DC

0CE106SF6DC

0CE106SF6DC

0CE106SF6DC

0CE106SF6DC

0CE106SF6DC

0CE106SF6DC

0CE106SF6DC

0CE106SF6DC

0CE106SF6DC

0CE106SF6DC

0CE106SF6DC

0CE106SF6DC

0CE105SK6DC

0CE106SF6DC

0CE476SF6DC

0CE106SF6DC

0CE107SF6DC

0CE476SF6DC

0CE476SF6DC

0CE476SF6DC

0CE476SF6DC

0CE476SF6DC

0CE476SF6DC

0CE107SF6DC

0CE107SF6DC

0CE107SF6DC

0CE106SF6DC

0CE106SF6DC

0CE106SF6DC

0CE107SF6DC

0CE226SF6DC

0CE106SF6DC

0CE106SF6DC

0CE226SF6DC

0CE226SF6DC

0CE106SF6DC

0CE226SF6DC

0CE226SF6DC

0CE226SF6DC

0CE226SF6DC











































22UF MVG 16V 20% SMD R/TP











C762

C769

C777

C778

C785

C800

C801

C802

C803

C812

C817

C822

C825

C827

C828

C829

C834

C834

C837

C840

C841

C847

C851

C852

C862

C863

C872

C873

C874

L1004

L1005

L1006

L1007

L1200

L1203

L1209

L1213

L803

L804

L805

L806

AR500

AR503

AR507

AR508

AR509

AR512

AR513

0CE226SF6DC

0CE226SF6DC

0CE226SF6DC

0CE226SF6DC

0CE335SK6DC

0CE226SF6DC

0CE226SF6DC

0CE476SF6DC

0CE226VF6DC

0CE226VF6DC

0CE226SF6DC

0CE107SF6DC

0CE335SK6DC

0CE107SF6DC

0CE106SF6DC

0CE106SF6DC

0CE106SF6DC

0CE107SF6DC

0CE106SF6DC

0CE106SF6DC

0CE107SF6DC

0CN105EJ56A

0CE108DH618

0CE108DH618

0CF4741L438

0CF4741L438

0CE335SK6DC

0CN105EJ56A

0CE108DH618

6140VB0004B

6140VB0004B

6140VB0004B

6140VB0004B

6140VB0004B

6140VB0004B

6140VB0004B

6140VB0004B

6140VB0022A

6140VB0022A

6140VB0022A

6140VB0022A

0RRZVTA001D

0RRZVTA001D

0RRZVTA001D

0RRZVTA001D

0RRZVTA001D

0RRZVTA001D

0RRZVTA001D






















1.0UF 3216 35V 10% R/TP X7R



0.47UF D 63V 5% TP 5 M/PE NI

0.47UF D 63V 5% TP 5 M/PE NI


1.0UF 3216 35V 10% R/TP X7R


26UH 1UEWPHY 22.5TURN YL-9N 0.4








CPS-0810 GET 22UH 21.5TURNS




22 OHM 1 / 16 W 1608 5%

22 OHM 1 / 16 W 1608 5%

22 OHM 1 / 16 W 1608 5%

22 OHM 1 / 16 W 1608 5%

22 OHM 1 / 16 W 1608 5%

22 OHM 1 / 16 W 1608 5%

22 OHM 1 / 16 W 1608 5%




COIL

RESISTOR

- 38 -


AR522

AR600

AR600

AR601

AR601

AR602

AR602

AR603

AR603

AR604

AR605

AR606

AR607

AR608

AR609

AR610

AR611

AR612

AR613

AR614

AR615

AR616

AR617

AR618

AR700

AR701

AR701

AR702

AR703

AR707

AR708

AR709

AR710

AR711

AR712

AR713

AR714

AR715

AR717

AR718

AR719

R801

R802

SW001

SW002

SW003

SW004

SW005

SW006

SW700

0RRZVTA001D

0RRZVTA001D

0RRZVTA001D

0RRZVTA001D

0RRZVTA001D

0RRZVTA001D

0RRZVTA001D

0RRZVTA001D

0RRZVTA001D

0RRZVTA001D

0RRZVTA001D

0RRZVTA001D

0RRZVTA001D

0RRZVTA001D

0RRZVTA001D

0RRZVTA001D

0RRZVTA001D

0RRZVTA001D

0RRZVTA001D

0RRZVTA001D

0RRZVTA001D

0RRZVTA001D

0RRZVTA001D

0RRZVTA001D

0RRZVTA001D

0RRZVTA001D

0RRZVTA001D

0RRZVTA001D

0RRZVTA001D

0RRZVTA001D

0RRZVTA001D

0RRZVTA001D

0RRZVTA001D

0RRZVTA001D

0RRZVTA001D

0RRZVTA001D

0RRZVTA001D

0RRZVTA001D

0RRZVTA001D

0RRZVTA001D

0RRZVTA001D

0RKZVTA001L

0RKZVTA001L

140-315A

140-315A

140-315A

140-315A

140-315A

140-315A

140-313B

22 OHM 1 / 16 W 1608 5%

22 OHM 1 / 16 W 1608 5%

22 OHM 1 / 16 W 1608 5%

22 OHM 1 / 16 W 1608 5%

22 OHM 1 / 16 W 1608 5%

22 OHM 1 / 16 W 1608 5%

22 OHM 1 / 16 W 1608 5%

22 OHM 1 / 16 W 1608 5%

22 OHM 1 / 16 W 1608 5%

22 OHM 1 / 16 W 1608 5%

22 OHM 1 / 16 W 1608 5%

22 OHM 1 / 16 W 1608 5%

22 OHM 1 / 16 W 1608 5%

22 OHM 1 / 16 W 1608 5%

22 OHM 1 / 16 W 1608 5%

22 OHM 1 / 16 W 1608 5%

22 OHM 1 / 16 W 1608 5%

22 OHM 1 / 16 W 1608 5%

22 OHM 1 / 16 W 1608 5%

22 OHM 1 / 16 W 1608 5%

22 OHM 1 / 16 W 1608 5%

22 OHM 1 / 16 W 1608 5%

22 OHM 1 / 16 W 1608 5%

22 OHM 1 / 16 W 1608 5%

22 OHM 1 / 16 W 1608 5%

22 OHM 1 / 16 W 1608 5%

22 OHM 1 / 16 W 1608 5%

22 OHM 1 / 16 W 1608 5%

22 OHM 1 / 16 W 1608 5%

22 OHM 1 / 16 W 1608 5%

22 OHM 1 / 16 W 1608 5%

22 OHM 1 / 16 W 1608 5%

22 OHM 1 / 16 W 1608 5%

22 OHM 1 / 16 W 1608 5%

22 OHM 1 / 16 W 1608 5%

22 OHM 1 / 16 W 1608 5%

22 OHM 1 / 16 W 1608 5%

22 OHM 1 / 16 W 1608 5%

22 OHM 1 / 16 W 1608 5%

22 OHM 1 / 16 W 1608 5%

22 OHM 1 / 16 W 1608 5%

1.0M OHM 1/2 W 5% TA52

1.0M OHM 1/2 W 5% TA52

TACT SKHV17910B LG C&D 12V






TACT 2LEAD 160G(TA) LG C&D


SW800

L100

L100

L1000

L1001

L1002

L1008

L1009

L101

L101

L1010

L1011

L1012

L1013

L1014

L1015

L1016

L1017

L1018

L1019

L102

L102

L103

L103

L104

L105

L105

L106

L107

L108

L1206

L1207

L1210

L1211

L1216

L1217

L1300

L1302

L1307

L1310

L1311

L1312

L1313

L1314

L1315

L1316

L1317

L1318

L1321

L1322

6600VM2006A

6210VC0006A

6210VC0006A

6210VC0006A

6210VC0006A

6210VC0006A

6210VC0006A

6210VC0006A

6210VC0006A

6210VC0006A

6210VC0006A

6210VC0006A

6210VC0006A

6210VC0006A

6210VC0006A

6210VC0006A

6210VC0006A

6210VC0006A

6210VC0006A

6210VC0006A

6210VC0006A

6210VC0006A

6210VC0006A

6210VC0006A

6210VC0006A

6210VC0006A

6210VC0006A

6210VC0006A

6200JB8010L

6200JB8010L

6210VC0006A

6210VC0006A

6210VC0006A

6210VC0006A

6210VC0006A

6210VC0006A

6210VC0006A

6210VC0006A

6210VC0006A

6210VC0006A

6210VC0006A

6210VC0006A

6210VC0006A

6210VC0006A

6210VC0006A

6210VC0006A

6210VC0006A

6210VC0006A

6210VC0006A

6210VC0006A

SDDF3PATP011 250V 4A HORIZONTAL .G

FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP



























MLB-201209-1000L-N2 R/TP 1000OHM 350MA

MLB-201209-1000L-N2 R/TP 1000OHM 350MA
























SWITCH

FILTER & CRYSTAL

- 39 -


L1325

L1326

L1327

L1328

L1329

L1330

L1331

L1332

L1333

L200

L201

L202

L203

L204

L204

L205

L205

L206

L206

L207

L207

L208

L208

L209

L210

L211

L212

L213

L214

L214

L215

L215

L216

L216

L217

L300

L301

L302

L303

L304

L305

L400

L400

L401

L401

L402

L403

L404

L405

L406

L407

L500

6210VC0006A

6210VC0006A

6210VC0006A

6210VC0006A

6210VC0006A

6210VC0006A

6210VC0006A

6210VC0006A

6210VC0006A

6200JB8013L

6210VC0006A

6210VC0006A

6210VC0006A

6210VC0005A

6210VC0006A

6210VC0005A

6210VC0006A

6210VC0005A

6210VC0006A

6210VC0005A

6210VC0006A

6210VC0005A

6210VC0006A

6210VC0005A

6200JB8010L

6200JB8010L

6200JB8010L

6200JB8010L

6200JB8010L

6200JB8010L

6200JB8010L

6200JB8010L

6200JB8010L

6200JB8010L

6200JB8010L

6210VC0006A

6210VC0006A

6210VC0006A

6210VC0006A

6210VC0006A

6210VC0006A

6210VC0006A

6210VC0006A

6210VC0006A

6210VC0006A

6210VC0006A

6210VC0006A

6210VC0005A

6210VC0005A

6210VC0005A

6210VC0006A

6210VC0006A










BEAD FEELUX R/TP 60 OHM TB201209U060




BK2125 HS 750 2X1.25X0.85MM R/TP


BK2125 HS 750 2X1.25X0.85MM R/TP


BK2125 HS 750 2X1.25X0.85MM R/TP


BK2125 HS 750 2X1.25X0.85MM R/TP


BK2125 HS 750 2X1.25X0.85MM R/TP


BK2125 HS 750 2X1.25X0.85MM R/TP

MLB-201209-1000L-N2 R/TP 1000OHM 350MA

MLB-201209-1000L-N2 R/TP 1000OHM 350MA

MLB-201209-1000L-N2 R/TP 1000OHM 350MA

MLB-201209-1000L-N2 R/TP 1000OHM 350MA

MLB-201209-1000L-N2 R/TP 1000OHM 350MA

MLB-201209-1000L-N2 R/TP 1000OHM 350MA

MLB-201209-1000L-N2 R/TP 1000OHM 350MA

MLB-201209-1000L-N2 R/TP 1000OHM 350MA

MLB-201209-1000L-N2 R/TP 1000OHM 350MA

MLB-201209-1000L-N2 R/TP 1000OHM 350MA

MLB-201209-1000L-N2 R/TP 1000OHM 350MA

FBMH3216 HM501NT 3.2X1.6X1.6MM












BK2125 HS 750 2X1.25X0.85MM R/TP

BK2125 HS 750 2X1.25X0.85MM R/TP

BK2125 HS 750 2X1.25X0.85MM R/TP




L501

L502

L503

L504

L505

L506

L507

L609

L700

L800

L807

L808

R102

R103

R106

R107

R108

X500

X600

X600

X700

X700

X800

JK103

JK200

JK201

JK202

P101

P102

P200

P201

A1

A2

A3

A4

A5

A6

A7

A8

A9

F801

PA001

TU100

TU101

P100

P200

6210VC0006A

6210VC0006A

6210VC0006A

6210VC0006A

6210VC0006A

6210VC0006A

6210VC0006A

6210VC0006A

6210VC0006A

6210VC0006A

6200JB8010L

6200JB8010L

6200JB8010L

6200JB8010L

6200JB8010L

6200JB8010L

6200JB8010L

6202VDT002K

6202VDB007B

6202VDT002J

6202VDB007B

6202VDT002B

156-A02M

6613V00026A

6612VJH020B

6612VJH020C

6612VJH019B

380-068E

6612BBBHN6A

380-363G

380-068E

3828VA0468D

6710V00126R

6410VEH003C

6850VA0004J

6851V00022C

3550V00338A

6850J00003A

6850J00004A

6866VA9001B

0FS1002B53K

6712000002B

6700MF0010A

6700MF0010B

6630VGA001C

6630VGA004B











MLB-201209-1000L-N2 R/TP 1000OHM 350MA

MLB-201209-1000L-N2 R/TP 1000OHM 350MA

MLB-201209-1000L-N2 R/TP 1000OHM 350MA

MLB-201209-1000L-N2 R/TP 1000OHM 350MA

MLB-201209-1000L-N2 R/TP 1000OHM 350MA

MLB-201209-1000L-N2 R/TP 1000OHM 350MA

MLB-201209-1000L-N2 R/TP 1000OHM 350MA

RESONATOR,SX-1 6MHZ +/- 30 PPM 16PF TP .

RESONATOR,HC49U 20.250MHZ 30PPM 13PF BK

RESONATOR,SX-1 13.500000MHZ +/- 50 PPM 14PF


RESONATOR,SX-1 SC14.3MHZ +/- 30 PPM


UJB-03-28A UGCOM 6613V00004S

PPJ122B PARK ELEC. A/V 6P

PPJ122C PARK ELEC. A/V 6P

PPJ121B PARK ELEC. A/V 4P

UEJ-CV-018 UGCOM D3.5 E/P

440062-1 AMP DVI INTERACED

6046B-01S PARKELEC H=8.0

UEJ-CV-018 UGCOM D3.5 E/P

MANUAL,OWNERS RF043B 126R TX 026H 7YRS

REMOTE CONTROLLER,RF043A PIP RZ-42PY20

POWER CORD,M2511A-001 VDE/SEMKO 2800MM

CABLE,COAXIAL UL1365#26 150MM UCA-EX-069

CABLE,COAXIAL(150MM),UL1365#26 VW-1

COVER,TX 6710V00091 ABS SPRAY #76

CABLE,DVI-D TO DVI-D UL20276 AWG28 3000MM

CABLE,LVDS UL20276 AWG30 500MM

CONNECTOR, 2990-9C UL 1161 AWG 26 TWI

FUSE,10000MA 250 V 5.2X20

REMOTE CONTROLLER RECEIVER,KSM-603SM12E-1

TUNER,TAUM-W501P 4 SYSTEM MAIN

TUNER,TAFM-W502P 4SYSTEM SUB

CONNECTOR,68114-1521 15PIN 2.29MM

CONNECTOR,69107-0921 9P 2.77MM

JACK

ACCESSORIES

MISCELLANEOUS

UNER(BOTTOM)

SIDE A/V(TOP)SIDE A/V(BOTTOM)

CONTROL(TOP)

CONTROL(BOTTOM)

Jun., 2004Printed in KoreaP/NO : 3828VD0161E

rt 42px20 chassis rf 043b service manual

Documents