s m tes_tem824pd.pdf

2005 Panasonic Communications Co., Ltd. Allrights reserved. Unauthorized copying anddistribution is a violation of law.

KX-TES824PDKX-TEM824PDKX-TE82461XKX-TE82474XKX-TE82480CEKX-TE82483CEKX-TE82491XKX-TE82492XKX-TE82493XKX-A227X(for Poland)

Advanced Hybrid System

IMPORTANT INFORMATION ABOUT LEAD FREE, (PbF), SOLDERINGIf lead free solder was used in the manufacture of this product the printed circuit boards will be marked PbF.Standard leaded, (Pb), solder can be used as usual on boards without the PbF mark.

When this mark does appear, please read and follow the special instructions described in this manual on the use of PbF and howit might be permissible to use Pb solder during service and repair work.

ORDER NO. KMS0503056CE

1 ABOUT LEAD FREE SOLDER (PbF: Pb free) 5 1.1. SUGGESTED PbF SOLDER 5

1.2. HOW TO RECOGNIZE THAT Pb FREE SOLDER IS

USED 6

2 FOR SERVICE TECHNICIANS 7 3 CAUTION 8

3.1. SAFETY PRECAUTIONS 8

3.2. INSULATION RESISTANCE TEST 8

3.3. BATTERY CAUTION 8

3.4. CAUTION 8

4 SPECIFICATIONS 9 4.1. GENERAL DESCRIPTION 9

4.2. CHARACTERISTICS 9

4.3. SYSTEM CAPACITY 9

5 SYSTEM OVERVIEW 10 5.1. SYSTEM COMPONENTS 10

5.2. SYSTEM CONNECTION DIAGRAM 11

6 NAMES AND LOCATIONS 12 7 CONNECTION 12

7.1. SERIAL INTERFACE CONNECTION 12

8 DISASSEMBLY INSTRUCTIONS 13 8.1. DISASSEMBLY INSTRUCTION 13

9 BLOCK DIAGRAM 16 9.1. SYSTEM BLOCK DIAGRAM 16

9.2. POWER BLOCK DIAGRAM 17

9.3. KX-TES824PD/KX-TEM824PD 1AP BLOCK DIAGRAM 17

9.4. KX-TEM824PD 2AP BLOCK DIAGRAM 18

9.5. KX-TES824PD/KX-TEM824PD POWER SUPPLY UNIT

BLOCK DIAGRAM 18

10 EXPLANATION OF BLOCK DIAGRAM 19 10.1. MAIN UNIT (KX-TES824PD/KX-TEM824PD) 19

11 CIRCUIT OPERATION 21 11.1. POWER SUPPY CIRCUIT 21

11.2. CO INTERFACE CIRCUIT 23

11.3. CROSS POINT SWITCH CIRCUIT 27

11.4. INTERCOM CIRCUIT 29

11.5. POWER FAILURE THROUGH CALL SWITCHING

CIRCUIT 30

11.6. DATA COMMUNICATION CIRCUIT 31

11.7. CONTROL CIRCUIT 33

11.8. TONE GENERATOR CIRCUIT 34

11.9. DTMF GENERATOR CIRCUIT 35

11.10. DTMF RECEIVER CIRCUIT 36

11.11. INT CALLID INTERFACE CIRCUIT 37

11.12. MODEM INTERFACE CIRCUIT 37

11.13. USB INTERFACE CIRCUIT 38

11.14. OGM INTERFACE CIRCUIT 38

11.15. RINGING SIGNAL GENERATOR CIRCUIT 39

11.16. SMDR INTERFACE CIRCUIT 39

11.17. DOORPHONE CARD INTERFACE (KX-TE82461X) 40

11.18. OGM CARD INTERFACE (KX-TE82491X) 40

11.19. BUILT in VOICE MESSAGE CARD INTERFACE (KX-

TE82492X) 41

11.20. CALL ID CARD INTERFACE (KX-TE82493X) 41

12 TROUBLESHOOTING GUIDE 42 12.1. NO OPERATION (Check POWER SUPPLY BOARD,

MAIN BOARD) 42

12.2. NO DIAL TONE (KX-TES824PD, MAIN BOARD OF KX-

TEM824PD) 43

12.3. CANNOT DIAL (KX-TES824PD, MAIN BOARD OF KX-

TEM824PD) 44

12.4. CANNOT CALL EXTENSION (KX-TES824PD, MAIN

BOARD OF KX-TEM824PD) 45

12.5. CANNOT USE PROPRIETARY TELEPHONE (KX-

TES824PD, MAIN BOARD OF KX-TEM824PD) 45

12.6. CANNOT RECEIVE INCOMING CALL (KX-TES824PD,

MAIN BOARD OF KX-TEM824PD) 45

12.7. CANNOT SEND DTMF DIALING (KX-TES824PD, MAIN


12.8. CANNOT RECEIVE CALL DIAL TONE (KX-TES824PD,


12.9. CANNOT SEND A HOLD ON MUSIC (KX-TES824PD,


12.10. NO DIAL TONE (SUB BOARD OF KX-TEM824PD) 47

12.11. CANNOT DIAL (SUB BOARD OF KX-TEM824PD) 48

12.12. CANNOT CALL EXTENSION (SUB BOARD OF KX-

TEM824PD) 48

12.13. CANNOT USE PROPRIETARY TELEPHONE (SUB


12.14. CANNOT RECEIVE INCOMING CALL (SUB BOARD OF

KX-TEM824PD) 49

12.15. CANNOT SEND DTMF DIALING (SUB BOARD OF KX-

TEM824PD) 49

12.16. CANNOT RECEIVE CALL DIAL TONE (SUB BOARD OF

KX-TEM824PD) 50

12.17. CANNOT SEND A HOLD ON MUSIC (SUB BOARD OF

KX-TEM824PD) 50

13 IC DATA 51 13.1. IC700 51

13.2. IC6 53

14 TERMINAL GUIDE OF ICS, TRANSISTORS AND DIODES 55 15 HOW TO REPLACE A FLAT PACKAGE IC 56

15.1. PREPARATION 56

15.2. REMOVAL PROCEDURE 56

15.3. INSTALLATION PROCEDURE 56

15.4. REMOVING SOLDER FROM BETWEEN PINS 56

16 FIXTURES AND TOOLS 57 17 CABINET AND ELECTRICAL PARTS LOCATION 58 18 ACCESSORIES AND PACKING MATERIALS 59 19 REPLACEMENT PARTS LIST (KX-TES824PD/KX-TEM824PD)

60 19.1. CABINET AND ELECTRICAL PARTS 60

CONTENTS Page Page

2

KX-TES824PD / KX-TEM824PD /

19.2. ACCESSORIES AND PACKING MATERIALS 60

19.3. MAIN BOARD PARTS 60

19.4. POWER SUPPLY BOARD PARTS 70

19.5. SUB BOARD PARTS 71

19.6. FIXTURES AND TOOLS 77

20 FOR THE SCHEMATIC DIAGRAM 78 21 SCHEMATIC DIAGRAM (KX-TES824PD/KX-TEM824PD) 80

21.1. MAIN No.1 (Extention A-D Block) 80

21.2. MAIN No.2 (Extention E-H Block) 84

21.3. MAIN No.3 (CO Block) 88

21.4. MAIN No.4 (Cross-Point Block) 92

21.5. MAIN No.5 (ASIC, Memory Block) 96

21.6. SUB 100

21.7. POWER SUPPLY 110

22 PRINTED CIRCUIT BOARD (KX-TES824PD/KX-TEM824PD) 114 22.1. MAIN BOARD 114

22.2. SUB BOARD 116

22.3. POWER SUPPLY 118

23 KX-TE82461X (4-PORT DOORPHONE CARD) 119 23.1. HOW TO RECOGNIZE THAT Pb FREE SOLDER IS

USED 120

23.2. LOCATION OF OPTIONAL CARDS 121

23.3. DOORPHONE/DOOROPENER CARD BLOCK DIAGRAM

122

23.4. EXPLANATION OF BLOCK DIAGRAM/CIRCUIT

OPERATIONS 124

23.5. TROUBLESHOOTING GUIDE 125

23.6. IC DATA 126

23.7. TERMINAL GUIDE OF ICS, TRANSISTORS AND

DIODES 127


23.9. REPLACEMENT PARTS LIST (KX-TE82461X) 129

23.10. FOR THE SCHEMATIC DIAGRAM 131

23.11. SCHEMATIC DIAGRAM (KX-TE82461X) 132

23.12. PRINTED CIRCUIT BOARD (KX-TE82461X) 134

24 KX-TE82474X (8-PORT SLT EXTENSION CARD) 135 24.1. HOW TO RECOGNIZE THAT Pb FREE SOLDER IS

USED 136


24.3. BLOCK DIAGRAM 140

24.4. EXPLANATION OF BLOCK DIAGRAM 140


24.6. IC DATA 149


DIODES 150

24.8. CABINET AND ELECTRICAL PARTS 151




24.12. MEMO 157



25 KX-TE82480CE (2-PORT ANALOGUE CO LINE AND 8-PORTSLT EXTENSION CARD) 166

25.1. HOW TO RECOGNIZE THAT Pb FREE SOLDER IS

USED 167




25.5. CIRCUIT OPERATION 173


25.7. IC DATA 186


DIODES 187

25.9. CABINET AND ELECTRICAL PARTS 188


25.11. REPLACEMENT PARTS LIST (KX-TE82480CE) 189


25.13. SCHEMATIC DIAGRAM (KX-TE82480CE) 196

25.14. PRINTED CIRCUIT BOARD (KX-TE82480CE) 204

26 KX-TE82483CE (3-PORT ANALOGUE CO LINE AND 8-PORTHYBRID EXTENSION) 206 26.1. HOW TO RECOGNIZE THAT Pb FREE SOLDER IS

USED 207




26.5. CIRCUIT OPERATION 211


26.7. IC DATA 225


DIODES 227

26.9. CABINET AND ELECTRICAL PATRS 228


26.11. REPLACEMENT PARTS LIST (KX-TE82483CE) 229


26.13. SCHEMATIC DIAGRAM (KX-TE82483CE) 236

26.14. PRINTED CIRCUIT BOARD (KX-TE82483CE) 246

27 KX-TE82491X (MESSAGE EXTENSION CARD FOR DISA/UCDOGMs) 248 27.1. HOW TO RECOGNIZE THAT Pb FREE SOLDER IS

USED 249





DIODES 253






28 KX-TE82492X (2-CHANNEL VOICE MESSAGE CARD) 259 28.1. HOW TO RECOGNIZE THAT Pb FREE SOLDER IS

USED 260



28.4. CIRCUIT OPERATIONS 263

3



28.6. IC DATA 266


DIODES 267






29 KX-TE82493X (3-PORT CALLER ID CARD) 273 29.1. HOW TO RECOGNIZE THAT Pb FREE SOLDER IS

USED 274



29.4. CIRCUIT OPERATIONS 276


29.6. IC DATA 278


DIODES 280






30 KX-A227X (BACK-UP BATTERY CABLE) 287 30.1. ACCESSORIES AND PACKING MATERIALS 288

30.2. REPLACEMENT PARTS LIST (KX-A227X) 289

4


1 ABOUT LEAD FREE SOLDER (PbF: Pb free)Note:

In the information below, Pb, the symbol for lead in the periodic table of elements, will refer to standard solder or solder thatcontains lead.

We will use PbF solder when discussing the lead free solder used in our manufacturing process which is made from Tin, (Sn),Silver, (Ag), and Copper, (Cu).

This model, and others like it, manufactured using lead free solder will have PbF stamped on the PCB. For service and repairwork we suggest using the same type of solder although, with some precautions, standard Pb solder can also be used.

Caution

PbF solder has a melting point that is 50 ~ 70 F, (30 ~ 40C) higher than Pb solder. Please use a soldering iron withtemperature control and adjust it to 700 20 F, (370 10C). In case of using high temperature soldering iron, pleasebe careful not to heat too long.

PbF solder will tend to splash if it is heated much higher than its melting point, approximately 1100F, (600C).

If you must use Pb solder on a PCB manufactured using PbF solder, remove as much of the original PbF solder as possibleand be sure that any remaining is melted prior to applying the Pb solder.

When applying PbF solder to double layered boards, please check the component side for excess which may flow onto theopposite side (See figure, below).

1.1. SUGGESTED PbF SOLDERThere are several types of PbF solder available commercially. While this product is manufactured using Tin, Silver, and Copper,(Sn+Ag+Cu), you can also use Tin and Copper, (Sn+Cu), or Tin, Zinc, and Bismuth, (Sn+Zn+Bi). Please check themanufacturers specific instructions for the melting points of their products and any precautions for using their product with othermaterials.The following lead free (PbF) solder wire sizes are recommended for service of this product: 0.3mm, 0.6mm and 1.0mm.

5


1.2. HOW TO RECOGNIZE THAT Pb FREE SOLDER IS USED

6


2 FOR SERVICE TECHNICIANSICs and LSIs are vulnerable to static electricity.When repairing, the following precautions will help prevent recurring malfunctions. 1. Cover the plastic parts boxes with aluminum foil. 2. Ground the soldering irons. 3. Use a conductive mat on the worktable. 4. Do not touch IC or LSI pins with bare fingers.

7


3 CAUTION3.1. SAFETY PRECAUTIONS 1. Before servicing, unplug the power cord to prevent an electric shock. 2. When replacing parts, use only the manufacturers recommended components for safety. 3. Check the condition of the power cord. Replace if wear or damage is evident. 4. After servicing, be sure to restore the lead dress, insulation barriers, insulation papers, shields, etc. 5. Before returning the serviced equipment to the customer, be sure to perform the following insulation resistance test to prevent

the customer from being exposed to shock hazards.

3.2. INSULATION RESISTANCE TEST 1. Unplug the power cord and short the two prongs of the plug with a jumper wire. 2. Turn on the power switch. 3. Measure the resistance value with ohmmeter between the jumpers AC plug and each exposed metal cabinet part, such as

screw threads, control shafts, handle brackets, etc.Note:

Some exposed parts may be isolated from the chassis by design. These will read infinity. 4. If the measurement is outside the specified limits, there is a possibility of shock hazard. The equipment should be repaired and

rechecked before it is returned to the customer.

3.3. BATTERY CAUTION 1. Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the

manufacturer. Dispose of used batteries according to the manufacturers Instructions. 2. The lithium battery is a critical component (type No.CR23541). Please observe for the proper polarity and the exact location

when replacing it and soldering the replacement lithium battery in.

3.4. CAUTIONThe power socket wall outlet should be located near this equipment and be easily accessible.

8


4 SPECIFICATIONS4.1. GENERAL DESCRIPTIONControl Bus Original bus (16-bit, 24 MHz)Switching Space Division CMOS Crosspoint SwitchPower Input 100 V AC to 240 V AC, 1.5A to 0.75A, 50 Hz/60HzExternal Battery +24 V DC (+12 V DC x 2)Maximum Power Failure Tolerance 300 ms (without using backup batteries)Memory Backup Duration 7 yearsDialling Outside (CO) Line Pulse (10 pps, 20 pps) or Tone (DTMF)

Extension Pulse (10 pps, 20 pps) or Tone (DTMF)Intercom Path 4Mode Conversion Pulse-DTMFRing Frequency 20 Hz/25 Hz (selectable)Operating Environment Temperature 0 C to 40 C

Humidity 10 % to 90 % (non-condensing)Conference Call Outside (CO) Line 2Music on Hold (MOH) 1 port

Selectable MOH: Internal/External/TonePaging Internal 1

Extension 1 portSerial Interface Port RS-232C 1

USB 1.1 1Extension Connection Cable SLT 1 pair wire (T, R)

PT 2-pair wire (T, R, H, L)DSS Console 1-pair wire (H, L)

Dimension 368 mm (W) x 284 mm (H) x 102 mm (D)Weight (when fully expanded) Approx. 3.5 kg

4.2. CHARACTERISTICSTerminal Equipment Loop Limit PT 40

SLT 600 including setDoorphone 20

Minimum Leakage Resistance 15000 minimumMaximum Number of ExtensionInstruments per Line

1 PT or SLT in standard connection1 PT and 1 SLT in parallel connection

Ring Voltage 75 Vrms at 20 Hz/25 Hz depending on the ringing loadOutside (CO) Line Loop Limit 1600 maximumHookswitch Flash/Recall Timing Range 24 ms-2032 msDoor Opener Current Limit 30 V DC/125 V AC, 3 A maximumPaging Terminal Impedance 600 MOH Terminal Impedance 10000

4.3. SYSTEM CAPACITY4.3.1. System Capacity

KX-TES824 KX-TEM824Basic System Outside (CO) lines 3 6

Extensions 8 16Fully Expanded System Outside (CO) lines 8 8

Extensions 24 24

9


4.3.2. Maximum Cards Terminal Equipmentltem KX-TES824 KX-TEM824

Extension Terminal 48 483-Port Analogue CO Line and 8-Port Hybrid Extension Card 1 -2-Port Analogue CO Line and 8-Port Single Line Telephone Extension Card 1 18-Port Single Line Telephone Extension Card 1 1Message Expansion Card for DISA/UCD OGMs 1 14-Port Doorphone Card 1 13-Port Caller ID Card 3 32-Channel Voice Message Card 1 1Doorphone 4 4Door Opener 4 4Pager 1 1Music on Hold (MOH) 1 1DSS Console 2 2

4.3.3. System Dataltem Max. Quantity

Operator 1System Speed Dialling 100One-touch Dialling 24 per extension (PT)Personal Speed Dialling 10 per extensionCall Park Area 10Absent Message 6Toll Restriction (TRS) COS 5Extension Group 8Message Waiting 8 per extensionMessage for Built-in Voice Message 128 messages (total 60 minutes)

5 SYSTEM OVERVIEW5.1. SYSTEM COMPONENTS

Model DescriptionMain Unit KX-TES824PD

KX-TEM824PDAdvances Hybrid System: 3 to 8 Outside (CO) Lines, 8 to 24 ExtensionsAdvances Hybrid System: 6 to 8 Outside (CO) Lines, 16 to 24 Extensions

Optional Service Cards KX-TE82461XKX-TE82474XKX-TE82480CEKX-TE82483CEKX-TE82491XKX-TE82492XKX-TE82493X

4-Port Doorphone Card8-Port Single Line Telephone Extension Card2-Port Analogue CO Line and 8-Port Single Line Telephone Extension Card3-Port Analogue CO Line and 8-Port Hybrid Extension CardMessage Expansion Card for DISA/UCD OGMs2-Channel Voice Message Card3-Port Caller ID Card

Proprietary Equipment KX-T30865KX-A227X

DoorphoneBackup Battery Cable

10


5.2. SYSTEM CONNECTION DIAGRAM

Connect a display-equipped proprietary telephone (PT) to extension jack 01, as this extension is automatically designated asthe manager extension.

11


6 NAMES AND LOCATIONS

7 CONNECTION7.1. SERIAL INTERFACE CONNECTION

12


8 DISASSEMBLY INSTRUCTIONS8.1. DISASSEMBLY INSTRUCTION1. Loosen the top cover screw (A).2. Remove the top front cover.Note

The screw cannot be removed front the cover.

3. Remove the 2 bottom-cover screws (B).

4. Open the bottom front cover.

13


5. Remove the 2 screws (A).6. Remove the power supply board cover.7. Pull out the 4 connectors.8. Remove the 1 screw (D).9. Remove the power supply board.

10. Pull out the 1 connector.11. Remove the 2 screws (A) and (C).12. Remove the main board.

14


Procedure:

Insert the SW CABLE into AC POWER SWICH.

Caution:

Be sure each colored wire is inserted to the correct lug (very important).

15


9 BLOCK DIAGRAM9.1. SYSTEM BLOCK DIAGRAM

Tone

Pow

er S

witc

h

DPH

4 C

ard

BV2

BV1

DOOR1 DOOR2

BV

Car

dO

GM

Car

d

Seria

lFl

ash

PIO

CO8

Int.C

ID

3BV

2BG

M 1

DPH

2

INT

4

Paig

ing

2To

ne

2D

TMF-

R

2

DTM

F-G

1

8por

t Ex

tens

ion

Bloc

k

2por

t C

o Bl

ock

PIO

8por

t Ex

tens

ion

Bloc

k

3por

t C

o Bl

ock

PIO

C

ross

Poi

nt

DTM

F-R

8por

t Ex

tens

ion

Bloc

k

3por

t C

o Bl

ock

C

ross

Poi

nt

Flas

h RO

M SR

AMCP

U DS

P

SRAM

8Mbi

t

CN

710

DSP#

2

DSP#

1

CN

707

DPH

Bloc

k #1,

#2

PIO

DPH

Bloc

k #3,

#4

CN

708

C

ID C

ard

#3

FPG

API

OS/

P

FSK

Dete

ct x

3

Jack

x8

C

ross

Poi

nt

Jack

x2

Jack

x8

Jack

x3

Jack

x8

Jack

x3

DTM

F De

tect

Stutt

er D

etect

x3

CID

Card #1

Sam

e as

CI

D Ca

rd

#3

CN

706

CN

711

C

N71

2

3AP

Car

d2A

P C

ard

1AP

Car

d

DTM

F-G

for C

O

CO

1-3

ex

t1-8

CO

4-6

ext9

-16

CO

7-8

ext1

7-24

RS23

2C

Bell

AC75

V 25

Hz

CN60

0

Ext Paging

Ext Music CN

601

Hos

t I/F

AC IN

25H

z +15V

-15V

+3

.3V

22

US

B

Int.

CID

x 3

BGM

MO

DEM

(Rx,

Tx)

OG

M(P

lay,

Rec

) x2

Vol

tage

chec

k

Rec

tific

atio

n

Rec

tific

atio

n

batte

ry

back

up

circ

uit

Ove

r cu

rren

t

Det

ect c

ircui

t

cont

rol

circ

uit

Vol

tage

ch

ange

nois

e fil

ter

L

N

FG

Sur

ge p

rote

ctor

Rin

ger

Am

p. ci

rcui

t

C N 7 0 5

24 V G N D

E x p a n s i o n C o n n e c t o r

E x p a n s i o n C o n n e c t o r

DTM

F-R

KX

-TE

S82

4PD

/KX

-TE

M82

4PD

SY

ST

EM

BLO

CK

DIA

GR

AM

+27V

PO

WE

RS

UP

PLYIC60

1

L1, L

2

Z1

IC8

IC7

IC2A

~C

IC1A

~C

IC7

IC60

0, IC

601,

IC60

2

IC61

3 IC

614

IC51

1 IC

512

IC50

0IC

501

IC50

2

IC70

4 IC

705

IC70

1IC

702

IC70

3

IC70

0IC

10IC

6IC

705

IC70

4IC

700

CN

703

CN

704

IC1

IC2

IC3

IC4

CID

Card #2

Sam

e as

CI

D Ca

rd

#3

16


9.2. POWER BLOCK DIAGRAM

9.3. KX-TES824PD/KX-TEM824PD 1AP BLOCK DIAGRAM

CO CIDCONNECTOR

Door PhoneDoor Opener

CONNECTOR

BV CardCONNECTOR

Exp308(2AP)

/Exp208(3AP)CardEXP

CONNECTOR

OGM CardCONNECTOR

D-Sub

USB

POWER UNITCONNECTOR

25HzNINT AC

TONE(D)

(UART)RXD, TXD

(DSP)Serial Flash i/f

(APT i/f)PRX2-3, PTX2-3, PTXE1-3

CO4-8

Host i/f

TAM1-2, TONE

DOOR1, 2

PIOASIC

CROSSPOINT

ROM

SRAM

ASIC8086DSPPIO

APT i/f

BELL

(APT i/f)PRX,PTX,PTXE1-3

(I/O)HOOK1-8,BELL1-8

Q1-4,TOE1,2,STD1,2

TONE

620,440,350Hz

DTMFR(1,2)(For EXT)

EXT1-8

BGM

PAGE

CO1-3

DTMFGenerator

(I/O) CO1

CO2

CO3

Paging jack

MOH jack

EXT1

EXT2

EXT3

EXT4

EXT5

EXT6

EXT7

EXT8

KX-TES824PD/KX-TEM824PD 1AP BLOCK DIAGRAM

CN706

CN708

CN707

CN701, CN702

CN710

CN703

CN704

CN705

IC700

IC709

IC704

IC613, IC614

IC600IC601IC602

IC6

IC7

CN601

CN600

17


9.4. KX-TEM824PD 2AP BLOCK DIAGRAM

Q1- 4,TOE1,2,STD1,2

CROSS

POINT

DTMFR(1,2) (For EXT)

PIO ASIC

(I/O)HOOK9-16,BELL9-16

CO4-6

EXT9-16

(I/O)

Exp308 (2AP)

/Exp208 (3AP) Card EXP

CONNECTOR

CO4-6

(APT i/f)PRX2,PTX2,PTXE1-3

CID4-6

Host i/f CO4

CO5

CO6

EXT9

EXT11

EXT10

EXT12

EXT13

EXT14

EXT15

EXT16

KX-TEM824PD 2AP BLOCK DIAGRAM

IC10

CN501, CN502

IC510, IC511

IC500, IC501, IC502

9.5. KX-TES824PD/KX-TEM824PD POWER SUPPLY UNIT BLOCK DIAGRAM

NoiseFilter

Rectification&

Smoothing

Controller

OverCurrent

Detection

Rectification&

Smoothing

VoltageDetection

DC-DCConverter

RingerAmplifier

FG

SW

(14)

BatteryBack up

+24V

GND

+27V

GND

+15V

-15V

3.3V

OUTPUTAC75V 25Hz

INTPUT20/25Hz

ACAlarm

AC IN

L

N

AC InputPowerDown

Detection

Primary Circuit Secondary Circuit

SurgeAbsorber

KX-TES824PD/KX-TEM824PD POWER SUPPLY UNIT BLOCK DIAGRAM

CN1

F1

F2

Z1 L1, L2

D10~D13, C5

D31D32

Q22Q23

Q2

Q1 PC1

T1

D101, C101

PC31

IC601

Q201, T2, IC201

CN301

Q101

Q503RL501

Q503RL501

18


10 EXPLANATION OF BLOCK DIAGRAM10.1. MAIN UNIT (KX-TES824PD/KX-TEM824PD)10.1.1. Power Supply CircuitThis power supply unit is a switching power supply. Power supply unit supplies DC voltage (+27V,+15V,-15V,3.3V) to main boardand other optional cards. And this unit has an adaptor circuit to back up battery. And this unit amplified the BELL signal (20/25Hzsign wave outputted from the ASIC) and supply bell signal to the telephone.

10.1.2. COL Interface CircuitThere are the interface circuits linking the CO line (CO1 -CO3) and the cross point circuit section.In case of KX-TEM824, the system has 6CO line (CO1 - CO6).

10.1.3. Cross Point CircuitThis is a space division switching system for connecting the following:The eight extension circuits with the eight CO, DTMF generator, DTMF receiver, INT-CALL ID, MODEM, OGM, VB, paging, musicon hold, tone etc.It is composed of 3 C-MOS ICs. (8 X 16 matrix: 2pcs and 4 X 8 matrix: 1pce).*In case of KXTEM824, the system has 6 C-MOS ICs (8 X 16 matrix: 3pcs and 4 X 8 matrix: 2pce, 8 X 8 matrix: 2pce).

10.1.4. Intercom CircuitThis is the interface circuit of the single line telephone, and it is composed of 8 intercom circuit (ICM1-8) In case of KX-TEM824,the system has 16 intercom circuits(ICM1-16).

10.1.5. Power Failure Through Call Switching CircuitKXTES824 have one power failure transfer circuit (CO1-EXT101).In case of KXTEM824,the system has 2 power failure circuit (CO1-EXT101 CO4 -EXT109).

10.1.6. Data Communication CircuitThe APT i/f module which performs communication with a private telephone machine is built in ASIC.8ch are controlled per block. Control of 3 blocks (24ch) is possible for ASIC at the maximum.

10.1.7. Control CircuitA control block consists of only the [ASIC] CPU (compatibility with Intel 8086) (IC700), Flash ROM (8Mbit) (IC705), SRAM (4Mbit)(IC704), and PIO ASIC (IC6). PIO ASIC mainly performs extension control and PIO built in ASIC CPU mainly performs extensioncontrol. RTC (Real Time Clock) and SRAM inside CPU are backed up by the lithium battery in order to hold time, system data, etc.

10.1.8. Tone Generator CircuitThe rectangle wave generated by the timer of ASIC is changed into sine wave with a low path filter, and various tones aregenerated.

10.1.9. DTMF Generator CircuitA DTMF generator is used for dispatch to outside line, and communication with the voice mail connected to the extension.

10.1.10. DTMF Receiver CircuitThe circuit which receives the Dial Tone Multi Frequency by which extension dispatch is carried out with the DTMF receiverconnected to the crossing point.

10.1.11. Int Call ID CircuitFSK/Dial Tone Multi Frequency generated by DSP in ASIC are connected even to a crossing point through AMP. The circuit whichsends out a CALLID signal to the telephone connected to an extension by connecting the line of INT-CALL-ID with arbitraryextensions.

10.1.12. Modem CircuitThe MODEM signal generated by DSP in ASIC is connected even to a crossing point through AMP.The circuit which connects the line of MODEM with arbitrary outside line, and enables MODEM communication with outside line.

19


10.1.13. USB CircuitThe circuit which makes communication possible by PC and 1.1 standards by the USB controller in ASIC.

10.1.14. OGM Circuit4M connected to ASIC by the memory controller in ASIC A maximum of 3-minute storing of OGM is possible to a serial flash Circuit.

10.1.15. Ring Signal Generator CircuitThis section generates the ring signal for the single line telephone. A 20/25Hz square wave is generated by the ASIC timer and sentto low pass filter and the ringing signal amplifier circuit and stepped by BELL transformer, and then passed it through the ringingsignal switching relay to the single line telephone.

10.1.16. SMDR Interface CircuitThis is the RS232C interface port. When the port is connected to a printer. The port can be used to output the SMDR featurerecording messages and the contents of the system program.

10.1.17. Door Phone InterfaceAn intercom card interface consists of two intercom paths connected to a crossing point, and address data and CS signals.

10.1.18. OGM InterfaceAn OGM card interface consists of the memory control signal, and the address data and CS signal which are connected to ASIC.

10.1.19. Call ID InterfaceA CALLID card interface consists of three CALLID signal lines from outside line, and address data and CS signal.

10.1.20. BV InterfaceBV card interface consists of two BV telephone call paths connected to a crossing point, and address data and CS signals.

20


11 CIRCUIT OPERATION11.1. POWER SUPPY CIRCUIT

11.1.1. The function of the power unit are listed belowAC-DC Inverter Function This function isolates and transduces the AC input voltage to

DC input and output of DC27V.DC-DC Converter Function This function outputs DC+15V, -15V and 3.3V from the

inputted DC27V.Ringing Signal Output Function Based on the 20/25Hz sine wave signal output from KX-

TES824/KX-TEM824, this function generates ringing andsupplies to the system.

AC Power Failure Detection This function detects any cut off of the AC power supply andoutputs an AC alarm signal to the CPU.

Battery Back Up Adaptor Function This function connects battery and service unit without batteryadaptor, only needs a cable connected to the battery andservice unit.

21


11.1.2. Control Section1) AC-DC Inverter FunctionThe AC input voltage is rectified and smoothed by D10-13 and C5. The obtained DC voltage is converted into a rectangular waveby the switching transistor Q1, then isolated and transduced by T1. This converted rectangular wave is rectified and smoothed byD101 and C101 to output DC27V. The DC27V is transmitted to the primary side by PC1 and then PWM- controlled to keepconstant. The switching frequency of Q1 is approximately 100KHz (70KHz~160KHz).2) DC-DC Inverter FunctionThe DC27V as input is converted into a rectangular wave by the switching transistor Q201, then isolated and transduced by T2.DC+15V, -15V and 3.3V are outputted by a rectification smoothing circuit composed of D401, D301, D701, C401, C301 and C702.The +3.3V of the three outputs is PWM-controlled by IC201 to keep constant.The switching frequency of the Q2 is approx. 55 KHz.3) Ringing signal output functionRinging signal (20/25Hz, 75Vac from main board) is amplified in power by power amplifier circuits (including of IC501, R601~R608,C601~C603).Ringing signal amplified in power is transmitted to the ringing transformer through pin 4 of CN601.4) AC Power Failure DetectionAC power failure is detected by D31~D32, R33~R41, C31, PC31.When AC power is on, PC31 is on.When AC power is turned off, PC31 is off.5) Battery back up functionThis back up battery adaptor circuit has DC supply function, from battery (+24V) to service unit and DC charge from service unitto battery (+24V). Charge current is typ. 0.4A.

22


11.2. CO INTERFACE CIRCUIT11.2.1. CompositionThis is composed of the following circuit:

1) Bell signal detection2) DC loop formation circuit3) Pulse dial transmission circuit4) CALL ID interface circuit5) COL bidirectional amplifier circuit

1) Bell signal detectionWhen CO line is idle, photo coupler PC1, PC2 are OFF.When there is an incoming signal from CO line, the current flows PC1 as in the following way.Tip L1 R2 PC1(1-2) C3 T2 R5 L1 Ring: This cause pin4 of PC1 to change the level from High to low.Ring L1 R5 T2 C3 PC2(1-2) R2 L1 Tip: This cause pin4 of PC2 to change the level from High to low.

23


2) DC loop formation circuitIn the off hook status, PC5 is ON.DC loop path:TipL1D1D2D3Q10(E-C)Q1(C-E)R9R8D3L1RingAt this time, the output of the photo coupler PC1 changes level from High to low.RingL1D3R8R9Q1(E-C)Q10(C-E)D3D2D1L1TipAt this time, the output of the photo coupler PC2 changes level from High to low.Afterwards, G/A monitor this change (low level to high level). If the high level continues for a specified time set by system dataprogramming. G/A assumes that CO line has become On hook status. And the CO line circuits is restored to the idle status.

3) Pulse dial transmission circuitWhen the Off hook status, pulse dial transmission is executed by alternating On hook and Off hook. The status of On hook orOff hook is controlled by the switching transistor Q10.

24


4) CALL ID interface circuitIt is insulated by the transformer in a COL circuit, and the call ID signal inputted from outside line is transmitted to a CALLIDoption card.The flow of a CALLID signalTipL1R2PC1(1-2)C3T2R5L1RingRingL1R5T2C3PC2(1-2)R2L1Tip

5) COL Bidirectional Amplifier circuitThis circuit consists of bidirectional amplifier function for communication between the extensions and COL, returns losscompensation for conference, shunt function and mute function.(Composition)For transmitting signals from the extensions to COL, this circuit consists of R34, R35, R26, R27, R18, R29, C14, C15, C10, C16and the operational amplifier (IC1).For transmitting signals from the COL to extensions, this circuit consists of R24, R25, R31, R28, R37, R30, C12, C13, C17, C18,and the operational amplifier (IC1).COL side-tone suppression circuit which includes a balanced network BN1 consists of R22 R23, C11 and R16, R17, R20, R21.EXT side-tone suppression circuit which includes a balanced network BN2 consists of R41, R42 and R40, R43, R38, R39.Also extension side-tone suppression circuit which includes a balanced network BN3 consists of R45, R46 for supplementingside-tone suppression during the conference communication.The analog switch (IC2) is used for the following:(1) Conference (Pin 6, 8 and 9)(2) Shunt (Pin 12, 10 and 11)(3) Mute (Pin 13, 1 and 2)

25


1) Conference switchNormally, pin 6 of the analog switch IC2 is low level, but during conferences, this pin becomes high level. Because, duringconferences, it should compensate the return loss by connecting the balance network BN2 and the balance network BN3 inparallel.

2) Mute switchThe mute switch consists of pin 13, 1 and 2 of the analog switch(IC2). This switch has the following functions.a) When a dial signal (DP) is sent to the COL, signals from the extensions are blocked.b) When the hold on music is sent to the COL, signals from the extensions are blocked.c) When the COL interface circuit is in the idle state, oscillation of COL bidirectional amplifier is inhibited. When pin 13 of IC2changes to low level, the interval between pins 1 and 2 of the analog switch turns off, and signals are blocked.

3) Shunt switchThe shunt switch consists of pin 12, 10 and 11 of analog switch IC2.It is used to prevent the pulse dialing signal which istransmitted to the extensions. When pin 12 of IC2 changes to high from low, the analog switch becomes ON (the intervalbetween pin 10 and 11), and GAIN of the COL cross point operational amplifier becomes zero.

Shunt SW Mute SW Conference SWpin no. of analog switch 12 13 6No connection (idle) H (on) L (off) L (off)Two party call L (off) H (on) L (off)Conference L (off) H (on) H (on)Hold on music transmission L (off) H (on) L (off)

Condition of COL interface amplifier circuit and analog switches.

26


11.3. CROSS POINT SWITCH CIRCUIT

11.3.1. CompositionThe cross point circuit composed of three cross point switch ICs (IC600 and 601:8X16, IC602:4X8).*In case of KX-TEM824, the system add more cross point switch ICs (IC500:8X16, IC501:8X8, IC502:4X8) which are in KX-TE82483.1) Cross Point Switch IC Operation

The cross point SW (IC600, IC601) contains a 8X16 array of cross point switches along with a 7 to 128 line decoder and latchcircuits. Any one of the 128 switches can be addressed by selecting appropriate seven address bits. The selected switch canbe turned on or off by applying either logical one or zero to the DATA input. Chip select allows the cross point array to becascaded for matrix expansion. Start a new line at this point SWs (IC602) contain 4X8 array of cross point switches along witha 5 to 32 line decoder and latch circuits.Any one of the 32 switches can be addressed by selecting appropriate five address bits. The selected switch can be turned onor off by applying either logical one or zero to the DATE input. Chip select allows the cross point array to be cascaded for matrixexpansion.

27


28


11.4. INTERCOM CIRCUIT11.4.1. INTERCOM CIRCUIT1) Composition

This is composed of the following circuits:a) +15V power source for the extension telephonesb) Hook detect for SLT and pulse dialing detectc) Bell ring trip section

2) Circuit operationa) Power supply to the telephoneWith the telephone off hook, a DC loop is formed, and current is supplied to the telephone. This circuit is limited to about 30mAby Q200, Q202, R202, R204 and Q201, Q203, R203, R205.+15VR204R202Q200RL201telephoneRL201Q201R203R205-15V

b) Hook detect for SLT and pulse dialing detectWhen the telephone handset is taken off, DC loop is formed and collector of U200 3,6 pin change to L from H.The ASIC detects the off hook condition.When the handset is replaced back on hook, the DC loop is interrupted and collector of U200 3,6 pin change to H from L andEXT Pulse dialing is input either in the on hook or off hook condition, and the break number (on hook condition) is counted andread as the dial number.

c) Bell ringing trip sectionWhen the telephone is a signal line telephone, extension calling is executed by means of a ringing signal. When the ringingsignal is supplied, RL201 turns ON and the current flows are as follows:Bell transformer ringing signal line RL201 telephone R206 -15V Bell transformer

29


11.5. POWER FAILURE THROUGH CALL SWITCHING CIRCUIT

11.5.1. Circuit operationIf an AC power failure lasts longer than one second (momentary power failure), the COL is directly connected to the extension.The COL1 will be connected with EXT101.When power failure, RL200 switches from EXT-line to CO [T/R].*In case of KX-TEM824, and the COL4 will be connected with EXT109.*In case of KX-TE82480, and the CO7 will be connected with EXT117.

30


11.6. DATA COMMUNICATION CIRCUIT

11.6.1. CompositionThis circuit is composed of the ASIC and the data communication interface circuits for the ICM circuit.

11.6.2. Circuit Operation1) Data Communication of ASIC

The APT I/f module is built into the CPU. It is for the APT communication of one block (8ch) and has the module of three blocks(24ch) at maximum.Selection signal of 3 bits to select 1ch out of 8chs is common to each block.The APT I/f module switches the communication point every 4ms in the ports 1-8/9-16/17-24 of the extension as follows:#101#102#103#104.....#108#101.....,#109#110#111#112.....#116#109.....,#117#118#119#120.....#124#117.....,In the case where the extension is not connected with the APT, it is recognized as an SLT connection and a dummycommunication is performed.

Interface block diagram of ASIC and ICM

31


2) Data Communication of ASIC and PITSWhen ASIC send the request signal to the proprietary telephone and after receiving the key input information (19 pulses) fromthe proprietary telephone and sending data (47 pulses) for LED control. 4bit CPU will receive acknowledge signal from theproprietary telephone.a) ReceptionThe data from the proprietary telephone is received via H and L lines along the path shown below.H.L line C208 IC200 T201 R235 Q210 ASICb) TransmissionThe data to the proprietary telephone is transmitted along the following Path.ASIC Q209 Q215 T201 IC200 C208 H.L line

32


11.7. CONTROL CIRCUIT11.7.1. CompositionThe control block is composed of the 16bit CPU(IC700: operating on 23.966MHz system clock from the 47.936MHz external crystaloscillator), the 8Mbit Flash ROM, the 4Mbit SRAM, and the ASIC for the I/O Port to control the outside line.The port to control the extension, the clock IC, the address decoder, and other CPU Peripheral circuit are included in theIC700.Also, the IC700 includes functions such as Extension CID(FSK, DTMF), MODEM sending/receiving, BGM, OGMrecording/playing, DTMF tone, CNG tone, CPT tone, and VOX detection.The SRAM has a lithium battery to back up information such as speed dial, date, dial data, and system data etc. The battery alsobacks up the clock IC in the IC700.I/O Port to control extension circuit, clock IC, address decoder, and other CPU Peripheral function are included in IC700. And IC700include the functions as transmission of Extension Caller ID, transmission & receive of MODEM, transmission BGM, recording &playing of OGM, detect of DTMF tone, CNG tone, CPT tone & VOX.the SRAM has a lithium battery as back up for protection of the memory of information of such as the speed dial, date, dial data,and system data, etc. This battery is back up clock IC in IC700 too.

33


11.8. TONE GENERATOR CIRCUIT11.8.1. CompositionThis system has three different tones, 620Hz, 440Hz, 350Hz.ASIC make the 350Hz, 620Hz and 440Hz square wave signals.The 350Hz and 440Hz square wave signals are shaped by the low pass filter to sin wave and become tone 1.On the other hand, 620Hz, square wave signal is shaped by the low pass filter to sin wave and becomes tone 2.Tone signals 1 and 2 turn ON and OFF at the cross point, thus dial tone, busy tone, and other tones, are produced.

34


11.9. DTMF GENERATOR CIRCUIT

11.9.1. CompositionDTMF generator is controlled by the 8 bit I/O data of CO G/A. DTMF tone is sent to CO line.

DTMF GENERATOR

R1 R2 R3 R4 C1 C2 C3 C4 TRANSMIT SIGNALL L L L L L L L DISABLEH L L L H L L L 1H L L L L H L L 2H L L L L L H L 3L H L L H L L L 4L H L L L H L L 5L H L L L L H L 6L L H L H L L L 7L L H L L H L L 8L L H L L L H L 9L L L H L H L L 0L L L H H L L L *L L L H L L H L #

35


11.10. DTMF RECEIVER CIRCUIT11.10.1. CompositionThe DTMF receiver circuit is composes of four DTMF receivers.IC613 and IC614 are used for the DTMF receivers from SLT connected to the extension.The DTMF signal is the 4bit parallel data and read by ASIC.*In case of KX-TEM824, the system have two more DTMF receiver which are in KX-TE82483.

36


11.11. INT CALLID INTERFACE CIRCUITBy using the DSP built into the ASIC, it is possible to produce CALLID signal and send it through the cross point to each extension.The CALLID signal can be switched between FSK and DTMF. There are three sources of the extension CALL ID in the system.

11.12. MODEM INTERFACE CIRCUITThe ASIC incorporates a modem function. There is no specified line and modem communication from any line is possible. Themodem communication speed is 2400bps and the system programming rewrite can be operated at the equivalent of 9600bps atmaximum by using software compression technology.

37


11.13. USB INTERFACE CIRCUITThis unit have one USB port for using PC programming. ASIC have USB 1.1 controller inside, so this unit make up USB interfaceonly ASIC and USB connector.

11.14. OGM INTERFACE CIRCUITThe TES/TEM824 model incorporates the functions of OGM, CNG and DTMF detection. At the OGM recording, it changes theanalog sound in the DSP of the ASIC into a digital signal of 16bits by A/D conversion. Then, the data is compressed (encoded) andstored in a 4M serial flash. Conversely, when being recovered the data stored in the 4M serial flash are decompressed to 16-bitdigital data, and then reproduced as an analog sound after the D/A conversion. The recording/reproducing is achieved byconnecting the path from external line through the cross point to the ASIC.The waveform coding method used at therecording/reproducing stage is the LD-ADPCM method. The DSP compresses the sound and stores the 4M serial flash using thememory management software in the DSP. The unit has the recording/reproducing function of 1CH as an initial mounting.Therecording time of the OGM is three minutes at maximum.Also, the CNG and DTMF detection are the functions operated in conjunction with the OGM and realized by the DSP in the ASIC.

38


11.15. RINGING SIGNAL GENERATOR CIRCUITThis section generates this ringing signal for the single line telephone. A 25Hz square wave is generated by the ASIC and sent tolow pass filter and ringing signal amplifier circuit and stepped by BELL transformer, and then passed through the ringing signalswitching relay to the single line telephone.

11.16. SMDR INTERFACE CIRCUITThis is the RS-232C interface port. When the port is connected to a printer, the port can be used to output the SMDR featurerecording messages and the contents of the system program.

39


11.17. DOORPHONE CARD INTERFACE (KX-TE82461X)This mounts a connector to connect the door phone card. Power at +15V, 3.3V and VAG are supplied to the door phone. Also, twobusses are supplied from the cross point to the door phone card.The tone for calling the door phone is directly supplied to the door phone and the ON/OFF control is performed in the door phone.

11.18. OGM CARD INTERFACE (KX-TE82491X)The CN710 is the interface connector for the expansion card to convert the OGM to 2CH. The unit can have the OGM of 2ch bymounting the option card KX-TE82491.Also, the recording time of the OGM can be extended to eight minutes at maximum.

40


11.19. BUILT in VOICE MESSAGE CARD INTERFACE (KX-TE82492X)The CN707 is the interface connector for the option card KX-TE82492 that has the MESSAGE of 2ch.The MESSAGE can be recorded from the external line or the extension. The recording time is 60 minutes for 1CH at maximum.

11.20. CALL ID CARD INTERFACE (KX-TE82493X)The TES/TEM824 system has three connectors to connect the Caller ID card to the external line in the main unit. One is for threeexternal lines mounted on the main card and the others are for 2AP and 3AP.The interface for the CALL ID of the external line is composed of an interface for receiving the CALLID signal from a station anda controller of the main card.The CALLID signal from the external line is transmitted through a transformer in the external line circuitto the CALLID connector. The control signals of CS, Address and Data are connected to the connector.

41


12 TROUBLESHOOTING GUIDE12.1. NO OPERATION (Check POWER SUPPLY BOARD, MAIN BOARD)

42


12.2. NO DIAL TONE (KX-TES824PD, MAIN BOARD OF KX-TEM824PD)

43


12.3. CANNOT DIAL (KX-TES824PD, MAIN BOARD OF KX-TEM824PD)

44


12.4. CANNOT CALL EXTENSION (KX-TES824PD, MAIN BOARD OF KX-TEM824PD)

12.5. CANNOT USE PROPRIETARY TELEPHONE (KX-TES824PD, MAINBOARD OF KX-TEM824PD)

12.6. CANNOT RECEIVE INCOMING CALL (KX-TES824PD, MAIN BOARD OFKX-TEM824PD)

45


12.7. CANNOT SEND DTMF DIALING (KX-TES824PD, MAIN BOARD OF KX-TEM824PD)

12.8. CANNOT RECEIVE CALL DIAL TONE (KX-TES824PD, MAIN BOARD OFKX-TEM824PD)

46


12.9. CANNOT SEND A HOLD ON MUSIC (KX-TES824PD, MAIN BOARD OFKX-TEM824PD)

12.10. NO DIAL TONE (SUB BOARD OF KX-TEM824PD)

47


12.11. CANNOT DIAL (SUB BOARD OF KX-TEM824PD)

12.12. CANNOT CALL EXTENSION (SUB BOARD OF KX-TEM824PD)

48


12.13. CANNOT USE PROPRIETARY TELEPHONE (SUB BOARD OF KX-TEM824PD)

12.14. CANNOT RECEIVE INCOMING CALL (SUB BOARD OF KX-TEM824PD)

12.15. CANNOT SEND DTMF DIALING (SUB BOARD OF KX-TEM824PD)

49


12.16. CANNOT RECEIVE CALL DIAL TONE (SUB BOARD OF KX-TEM824PD)

12.17. CANNOT SEND A HOLD ON MUSIC (SUB BOARD OF KX-TEM824PD)

50


13 IC DATA13.1. IC700

PIN No Pin Name I/O Function127 Q1 I DTMF Rx Data[0]128 Q2 I DTMF Rx Data[1]129 Q3 I DTMF Rx Data[2]130 Q4 I DTMF Rx Data[3]131 STD1 I DTMF-R1 Status132 STD2 I DTMF-R2 Status133 TOE1 O DTMF-R1 Data output Enable134 TOE2 O DTMF-R2 Data output Enable135 BELL1 O Ext BELL Control 1136 BELL2 O Ext BELL Control 2137 BELL3 O Ext BELL Control 3142 BELL4 O Ext BELL Control 4143 BELL5 O Ext BELL Control 5144 BELL6 O Ext BELL Control 6145 BELL7 O Ext BELL Control 7146 BELL8 O Ext BELL Control 8147 HOOK1 I Ext Hook Detect 1148 HOOK2 I Ext Hook Detect 2149 HOOK3 I Ext Hook Detect 3150 HOOK4 I Ext Hook Detect 4151 HOOK5 I Ext Hook Detect 5152 HOOK6 I Ext Hook Detect 6153 HOOK7 I Ext Hook Detect 7154 HOOK8 I Ext Hook Detect 8155 SYSCLR I System Clear158 DET_EXT I Extension 08/208 Card Detection159 DET_308 I Extended 308 Card Detection160 DET_OGM I OGM Card Detection161 LED_SW O LED ON162 PAG_SW O External Paging Output163 OUT232C O Control Port for RS232C164 NRESET O ALL Module Reset94 USB_VBUS I Power Supply Monitor; 0: Detected, 1: Not detected95 USB_PUP O Pullup Control96 PD_RLY O SW Relay for Power Down

51


PIN No Pin Name I/O Function97 MOH_SW O External BGM Input98 BREAK O Line 1.5V Disconnection, 0: Disconnected, 1: Connected99 IN232C I Monitor Port for RS232C100 NC - -103 NC - -

52


13.2. IC6

PIN No Pin Name I/O Function4 CDT1 I Current Detect15 CDT2 I Current Detect26 CDT3 I Current Detect37 DET_DOOR I Door Phone Card Detect8 NINT_AC I AC Power-off Detection Signal9 NINT_DC I DC Power-off Detection Signal

10 OGM_SW O Connected to the extension11 BLRLY O BELL Disconnection; 0: Disconnected, 1: Connected13 CO1_VAG O Connected to VAG14 CO2_VAG O Connected to VAG15 CO3_VAG O Connected to VAG16 CO4_VAG O Connected to VAG17 CO5_VAG O Connected to VAG18 CO6_VAG O Connected to VAG19 CO7_VAG O Connected to VAG20 CO8_VAG O Connected to VAG21 CLM1 O Column Input 124 CLM2 O Column Input 225 CLM3 O Column Input 326 CLM4 O Column Input 427 ROW1 O Row Input 128 ROW2 O Row Input 229 ROW3 O Row Input 330 ROW4 O Row Input 436 CONF3 O Conference37 MUTE3 O Send MUTE38 DL3 O Pulse Dial39 DS3 O Dial Shunt40 SHUNT3 O Receive Mute41 PAD3 O 3dB PAD44 BELLA3 I Bell Detect A45 BELLB3 I Bell Detect B46 CONF2 O Conference47 MUTE2 O Send MUTE48 DL2 O Pulse Dial49 DS2 O Dial Shunt50 SHUNT2 O Receive Mute51 PAD2 O 3dB PAD53 BELLA2 I Bell Detect A54 BELLB2 I Bell Detect B55 CONF1 O Conference56 MUTE1 O Send MUTE

53


PIN No Pin Name I/O Function57 DL1 O Pulse Dial58 DS1 O Dial Shunt59 SHUNT1 O Receive Mute60 PAD1 O 3dB PAD61 BELLA1 I Bell Detect A64 BELLB1 I Bell Detect B31 DET_CID1 I CID Card Detect(1AP)32 DET_CID2 I CID Card Detect(2AP)34 DET_CID3 I CID Card Detect(3AP)35 DET_TAM I Voice Message Card(10min)

54


14 TERMINAL GUIDE OF ICS, TRANSISTORS AND DIODES

55


15.1. PREPARATION

PbF (: Pb free) Solder

Soldering Iron

Tip Temperature of 700F 20F (370C 10C)Note: We recommend a 30 to 40 Watt soldering iron. Anexpert may be able to use a 60 to 80 Watt iron wheresomeone with less experience could overheat and damagethe PCB foil.

Flux

Recommended Flux: Specific Gravity 0.82.Type RMA (lower residue, non-cleaning type)Note: See ABOUT LEAD FREE SOLDER (PbF: Pb free)(P.5).

15.2. REMOVAL PROCEDURE 1. Put plenty of solder on the IC pins so that the pins can be

completely covered.Note:

If the IC pins are not soldered enough, you may givepressure to the P.C. board when cutting the pins with acutter.

2. Make a few cuts into the joint (between the IC and its pins)first and then cut off the pins thoroughly.

3. While the solder melts, remove it together with the IC pins.

When you attach a new IC to the board, remove all solderleft on the land with some tools like a soldering wire. If some

solder is left at the joint on the board, the new IC will not beattached properly.

15.3. INSTALLATION PROCEDURE 1. Tack the flat pack IC to the PCB by temporarily soldering

two diagonally opposite pins in the correct positions on thePCB.

Be certain each pin is located over thecorrect pad on the PCB.

2. Apply flux to all of the pins on the IC.

3. Being careful to not unsolder the tack points, slide thesoldering iron along the tips of the pins while feedingenough solder to the tip so that it flows under the pins asthey are heated.

15.4. REMOVING SOLDER FROMBETWEEN PINS

1. Add a small amount of solder to the bridged pins. 2. With a hot iron, use a sweeping motion along the flat part of

the pin to draw the solder from between the adjacent pads.

15 HOW TO REPLACE A FLAT PACKAGE ICEven if you do not have the special tools (for example, a spot heater) to remove the Flat IC, with some solder (large amount),a soldering iron and a cutter knife, you can easily remove the ICs that have more than 100 pins.

56


16 FIXTURES AND TOOLS

57


17 CABINET AND ELECTRICAL PARTS LOCATION

58


18 ACCESSORIES AND PACKING MATERIALS

59


19 REPLACEMENT PARTSLIST (KX-TES824PD/KX-TEM824PD)

Note: 1. RTL (Retention Time Limited)

The marking (RTL) indicates that the Retention Time islimited for this item.After the discontinuation of this assembly in production, theitem will continue to be available for a specific period oftime. The retention period of availability depends on thetype of assembly and the laws governing parts and productretention. At the end of this period, the assembly will nolonger be available.

2. Important safety noticeComponents identified by the mark indicates specialcharacteristics important for safety. When replacing any ofthese components, only use specified manufactures parts.

3. The S mark means the part is one of some identical parts.For that reason, it may be different from the installed part.

4. ISO code (Example: ABS-94HB) of the remarks columnshows quality of the material and a flame resisting gradeabout plastics.

5. RESISTORS & CAPACITORSUnless otherwise specified;All resistors are in ohms (), k=1000, M=1000kAll capacitors are in MICRO FARADS (F), p=(F)*Type & Wattage of Resistor

19.1. CABINET AND ELECTRICALPARTS

Ref.No.

Part No. Part Name & Description Remarks

1 PQHD10011V SMALL SCREW2 PSGG1009Z1 GRILLE PS3 PSGG1009Y1 GRILLE (KX-TEM824PD) PS4 PSHE1051Z SPACER5 PSHE1068Z NUT

Ref.No.


6 PSHR1146Z SPACER, LED PS7 PSHR1336Z SPACER, PCB HOLDER PA668 PSJS02Q11Z CONNECTOR, 2P9 PSJS11P24Z CONNECTOR, 11P10 PSKE1020X1 COVER, POWER BOARD PS11 PSKF1030S1 CABINET COVER (KX-TES824PD) PS11 PSKF1030R1 CABINET COVER (KX-TEM824PD) PS12 PSKM1056U1 CABINET BODY PS13 PSKV1010Z1 COVER, CABLE PS14 PSLT1K9M2A TRANSFORMER15 PSMH1135Y ANGLE16 PSMH1151Y ANGLE17 PSQT1397Z LABEL, CAUTION18 PSQT1398Z LABEL, BATTERY19 PSQT1431Z LABEL, WARNING20 PSUS1022Z COIL SPRING21 PSWSTES824BX SWITCH ASSY22 PSYEES824PDM NAME PLATE (KX-TES824PD)22 PSYEEM824PDM NAME PLATE (KX-TEM824PD)23 XUC3VWP RETAINING RING24 K1KA40A00234 CONNECTOR (KX-TEM824PD)25 PQLB5F1 INSULATOR

19.2. ACCESSORIES AND PACKINGMATERIALS

Ref.No.


A1 PSJA1007Z POWER CORDA2 PQJP1E1Z PLUGA3 PQHE5004Z WOOD SCREWA4 XWG35FJ WASHERA5 PSHE1071Z BANDA6 PSQX3609ZCD INSTRUCTION BOOK, CD-ROMA7 PSQX3412Y INSTRUCTION BOOKA8 PSHR1177Z REVETA9 PSQW2219Z LEAFLETP1 PSZKES824PDM PACKING CASE, CARTON BOX

ASSY (KX-TES824PD)P1 PSZKEM824PDM PACKING CASE, CARTON BOX

ASSY (KX-TEM824PD)P2 PSPN1089Z ACCESSORY BOX, PAPERP3 XZB06X13A03 PROTECTION COVERP4 XZB30X40A04 PROTECTION COVERP5 XZB05X08A03 PROTECTION COVER, MANUAL PACKP6 PSPP1050Z PROTECTION COVERP7 PSPD1135Z CUSHIONP8 PSPD1136Z CUSHIONP9 PSPD1137Z CUSHION

19.3. MAIN BOARD PARTSRef.No.


PCB1 PSWPTES824PD MAIN BOARD ASSY (RTL)(ICS)

IC1A PQVINJM4558V IC SIC1B PQVINJM4558V IC SIC1C PQVINJM4558V IC SIC2A C0JBAR000248 ICIC2B C0JBAR000248 ICIC2C C0JBAR000248 ICIC6 C1CB00001851 ICIC7 C1CB00001866 ICIC200 PQVIMC4051BF IC SIC600 C1CB00001893 ICIC601 C1CB00001893 ICIC602 C1CB00001892 ICIC604 PQVINJM4558V IC SIC605 PQVINJM4558V IC SIC606 PQVINJM4558V IC SIC607 C0JBAR000248 IC

60


Ref.No.


IC608 C0JBAR000248 ICIC609 PQVINJM4558V IC SIC610 PQVINJM4558V IC SIC611 PQVINJM4558V IC SIC612 PQVINJM4558V IC SIC613 C1CB00001876 ICIC614 C1CB00001876 ICIC616 PQVINJM4558V IC SIC617 C0JBAR000248 ICIC700 C1CB00001853 ICIC701 C0CBAKE00010 ICIC702 C0CBAAC00083 ICIC703 C0CBAAC00154 ICIC704 C3BBKG000086 ICIC705 PSWITES824PD ICIC706 C3FBKC000127 ICIC707 C1CB00001825 ICIC708 PQVITC7SU04F IC SIC709 PQVINJM4558V IC SIC710 C0JBAB000407 ICIC712 C0EBE0000176 ICIC713 C0JBAC000382 ICIC714 C0JBAB000733 ICIC715 C0JBAC000382 ICIC716 C0JBAB000733 IC

(TRANSISTORS)Q1A 2SC4731S TRANSISTOR(SI) SQ1B 2SC4731S TRANSISTOR(SI) SQ1C 2SC4731S TRANSISTOR(SI) SQ5A UN5213 TRANSISTOR(SI) SQ5B UN5213 TRANSISTOR(SI) SQ5C UN5213 TRANSISTOR(SI) SQ10A 2SA1627 TRANSISTOR(SI) SQ10B 2SA1627 TRANSISTOR(SI) SQ10C 2SA1627 TRANSISTOR(SI) SQ200A 2SB766ARTX TRANSISTOR(SI) SQ200B 2SB766ARTX TRANSISTOR(SI) SQ200C 2SB766ARTX TRANSISTOR(SI) SQ200D 2SB766ARTX TRANSISTOR(SI) SQ200E 2SB766ARTX TRANSISTOR(SI) SQ200F 2SB766ARTX TRANSISTOR(SI) SQ200G 2SB766ARTX TRANSISTOR(SI) SQ200H 2SB766ARTX TRANSISTOR(SI) SQ201A 2SD874A TRANSISTOR(SI) SQ201B 2SD874A TRANSISTOR(SI) SQ201C 2SD874A TRANSISTOR(SI) SQ201D 2SD874A TRANSISTOR(SI) SQ201E 2SD874A TRANSISTOR(SI) SQ201F 2SD874A TRANSISTOR(SI) SQ201G 2SD874A TRANSISTOR(SI) SQ201H 2SD874A TRANSISTOR(SI) SQ202A 2SB1218A TRANSISTOR(SI)Q202B 2SB1218A TRANSISTOR(SI)Q202C 2SB1218A TRANSISTOR(SI)Q202D 2SB1218A TRANSISTOR(SI)Q202E 2SB1218A TRANSISTOR(SI)Q202F 2SB1218A TRANSISTOR(SI)Q202G 2SB1218A TRANSISTOR(SI)Q202H 2SB1218A TRANSISTOR(SI)Q203A 2SD1819A TRANSISTOR(SI)Q203B 2SD1819A TRANSISTOR(SI)Q203C 2SD1819A TRANSISTOR(SI)Q203D 2SD1819A TRANSISTOR(SI)Q203E 2SD1819A TRANSISTOR(SI)Q203F 2SD1819A TRANSISTOR(SI)Q203G 2SD1819A TRANSISTOR(SI)Q203H 2SD1819A TRANSISTOR(SI)Q207A 2SD1819A TRANSISTOR(SI)Q207B 2SD1819A TRANSISTOR(SI)Q207C 2SD1819A TRANSISTOR(SI)Q207D 2SD1819A TRANSISTOR(SI)Q207E 2SD1819A TRANSISTOR(SI)Q207F 2SD1819A TRANSISTOR(SI)

Ref.No.


Q207G 2SD1819A TRANSISTOR(SI)Q207H 2SD1819A TRANSISTOR(SI)Q209 PQVTDTC143E TRANSISTOR(SI) SQ209A 2SD1819A TRANSISTOR(SI)Q209B 2SD1819A TRANSISTOR(SI)Q209C 2SD1819A TRANSISTOR(SI)Q209D 2SD1819A TRANSISTOR(SI)Q209E 2SD1819A TRANSISTOR(SI)Q209F 2SD1819A TRANSISTOR(SI)Q209G 2SD1819A TRANSISTOR(SI)Q209H 2SD1819A TRANSISTOR(SI)Q210 2SD1819A TRANSISTOR(SI)Q212 PQVTDTC143E TRANSISTOR(SI) SQ213 PQVTDTC143E TRANSISTOR(SI) SQ214 PQVTDTC143E TRANSISTOR(SI) SQ215 PQVTDTA114EU TRANSISTOR(SI) SQ216 2SD1819A TRANSISTOR(SI)Q217 2SD1819A TRANSISTOR(SI)Q222 2SB1417P TRANSISTOR(SI) SQ223 PQVTDTC143E TRANSISTOR(SI) SQ608 UN5213 TRANSISTOR(SI) SQ609 UN5213 TRANSISTOR(SI) SQ620 UN5213 TRANSISTOR(SI) SQ700 2SD1819A TRANSISTOR(SI)Q701 UN5213 TRANSISTOR(SI) SQ702 B1GDCFNA0001 TRANSISTOR(SI)Q703 PQVTDTC144E TRANSISTOR(SI) SQ704 2SC2412K TRANSISTOR(SI) SQ705 PQVTDTC143E TRANSISTOR(SI) SU2A B1GFAFNN0001 TRANSISTOR(SI)U2B B1GFAFNN0001 TRANSISTOR(SI)U2C B1GFAFNN0001 TRANSISTOR(SI)U200A PSVTUMX1NTN TRANSISTOR(SI) SU200B PSVTUMX1NTN TRANSISTOR(SI) SU200C PSVTUMX1NTN TRANSISTOR(SI) SU200D PSVTUMX1NTN TRANSISTOR(SI) SU200E PSVTUMX1NTN TRANSISTOR(SI) SU200F PSVTUMX1NTN TRANSISTOR(SI) SU200G PSVTUMX1NTN TRANSISTOR(SI) SU200H PSVTUMX1NTN TRANSISTOR(SI) SU600 B1GFAFNN0001 TRANSISTOR(SI)U601 B1GFAFNN0001 TRANSISTOR(SI)U602 B1GFAFNN0001 TRANSISTOR(SI)U603 B1GFAFNN0001 TRANSISTOR(SI)

(DIODES)D1A PQVDRLZ2R0B DIODE(SI) SD1B PQVDRLZ2R0B DIODE(SI) SD1C PQVDRLZ2R0B DIODE(SI) SD2A PQVDRLZ2R0B DIODE(SI) SD2B PQVDRLZ2R0B DIODE(SI) SD2C PQVDRLZ2R0B DIODE(SI) SD3A B0EDKT000001 DIODE(SI)D3B B0EDKT000001 DIODE(SI)D3C B0EDKT000001 DIODE(SI)D202A MA8036H DIODE(SI) SD202B MA8036H DIODE(SI) SD202C MA8036H DIODE(SI) SD202D MA8036H DIODE(SI) SD202E MA8036H DIODE(SI) SD202F MA8036H DIODE(SI) SD202G MA8036H DIODE(SI) SD202H MA8036H DIODE(SI) SD203A MA8036H DIODE(SI) SD203B MA8036H DIODE(SI) SD203C MA8036H DIODE(SI) SD203D MA8036H DIODE(SI) SD203E MA8036H DIODE(SI) SD203F MA8036H DIODE(SI) SD203G MA8036H DIODE(SI) SD203H MA8036H DIODE(SI) SD204A MA8039 DIODE(SI) SD204B MA8039 DIODE(SI) SD204C MA8039 DIODE(SI) S

61


Ref.No.


D204D MA8039 DIODE(SI) SD204E MA8039 DIODE(SI) SD204F MA8039 DIODE(SI) SD204G MA8039 DIODE(SI) SD204H MA8039 DIODE(SI) SD205A MA111 DIODE(SI) SD205B MA111 DIODE(SI) SD205C MA111 DIODE(SI) SD205D MA111 DIODE(SI) SD205E MA111 DIODE(SI) SD205F MA111 DIODE(SI) SD205G MA111 DIODE(SI) SD205H MA111 DIODE(SI) SD208A MA143 DIODE(SI) SD208B MA143 DIODE(SI) SD208C MA143 DIODE(SI) SD208D MA143 DIODE(SI) SD208E MA143 DIODE(SI) SD208F MA143 DIODE(SI) SD208G MA143 DIODE(SI) SD208H MA143 DIODE(SI) SD209A MA111 DIODE(SI) SD209B MA111 DIODE(SI) SD209C MA111 DIODE(SI) SD209D MA111 DIODE(SI) SD209E MA111 DIODE(SI) SD209F MA111 DIODE(SI) SD209G MA111 DIODE(SI) SD209H MA111 DIODE(SI) SD220 MA111 DIODE(SI) SD221 MA111 DIODE(SI) SD222 MA143 DIODE(SI) SD600 B0BC2R400008 DIODE(SI)D601 B0BC2R400008 DIODE(SI)D602 MA111 DIODE(SI) SD603 MA111 DIODE(SI) SD604 MA111 DIODE(SI) SD605 MA111 DIODE(SI) SD606 MAZ80620LL DIODE(SI)D701 MAZ82000ML DIODE(SI)D702 MA111 DIODE(SI) SD703 MA728 DIODE(SI) SD704 MA111 DIODE(SI) SD705 MA728 DIODE(SI) SDA200A MA142WKTX DIODE(SI) SDA200B MA142WKTX DIODE(SI) SDA200C MA142WKTX DIODE(SI) SDA200D MA142WKTX DIODE(SI) SDA200E MA142WKTX DIODE(SI) SDA200F MA142WKTX DIODE(SI) SDA200G MA142WKTX DIODE(SI) SDA200H MA142WKTX DIODE(SI) SLED700 B3ABB0000146 LED

(BATTERY)BAT700 CR23541GUF LITHIUM BATTERY

(CONNECTORS)CN701 K1KB40C00002 CONNECTOR, 40PCN702 K1KB40C00002 CONNECTOR, 40PCN703 PSJP09A64Z CONNECTOR, 9P SCN704 K1FA104B0017 CONNECTOR, 104PCN705 PQJP11G30Z CONNECTOR, 11P SCN706 K1KA30A00196 CONNECTOR, 30PCN707 K1KA30A00196 CONNECTOR, 30PCN708 PQJP30A09Z CONNECTOR, 30PCN710 K1KA60A00144 CONNECTOR, 60PCN711 K1KA30A00196 CONNECTOR, 30PCN712 K1KA30A00196 CONNECTOR, 30P

(COMPONENTS PARTS)RA100 D1H81034A037 RESISTOR ARRAY, 10KRA101 D1H81034A037 RESISTOR ARRAY, 10KRA102 D1H81034A037 RESISTOR ARRAY, 10KRA200 D1H81034A037 RESISTOR ARRAY, 10KRA600 D1H81034A037 RESISTOR ARRAY, 10K

Ref.No.


RA601 D1H81034A037 RESISTOR ARRAY, 10KRA602 D1H81034A037 RESISTOR ARRAY, 10KRA603 D1H81034A037 RESISTOR ARRAY, 10KRA700 D1H81034A037 RESISTOR ARRAY, 68RA701 D1H86804A024 RESISTOR ARRAY, 68RA702 D1H86804A024 RESISTOR ARRAY, 68RA703 D1H86804A024 RESISTOR ARRAY, 68RA704 D1H86804A024 RESISTOR ARRAY, 68RA705 D1H86804A024 RESISTOR ARRAY, 68RA706 D1H86804A024 RESISTOR ARRAY, 68RA708 D1H81034A037 RESISTOR ARRAY, 10KRA709 D1H81034A037 RESISTOR ARRAY, 10KRA710 D1H81034A037 RESISTOR ARRAY, 10KRA711 D1H81034A037 RESISTOR ARRAY, 10KRA712 D1H81034A037 RESISTOR ARRAY, 10KRA713 D1H81034A037 RESISTOR ARRAY, 10KRA714 D1H81034A024 RESISTOR ARRAY, 10KRA715 D1H81034A024 RESISTOR ARRAY, 10KRA716 D1H81034A037 RESISTOR ARRAY, 10KRA717 D1H81034A037 RESISTOR ARRAY, 10KRA718 D1H81034A037 RESISTOR ARRAY, 10KRA719 D1H81034A037 RESISTOR ARRAY, 10KRA720 D1H81034A037 RESISTOR ARRAY, 10KRA721 D1H81034A024 RESISTOR ARRAY, 10KRA722 D1H81034A024 RESISTOR ARRAY, 10KRA723 D1H81034A037 RESISTOR ARRAY, 10KRA724 D1H86804A024 RESISTOR ARRAY, 68RA725 D1H86804A024 RESISTOR ARRAY, 68RA726 D1H86804A024 RESISTOR ARRAY, 68RA727 D1H86804A024 RESISTOR ARRAY, 68RA728 D1H81034A037 RESISTOR ARRAY, 10KRA729 D1H81034A037 RESISTOR ARRAY, 10K

(COILS)L1A PFLE003 COIL SL1B PFLE003 COIL SL1C PFLE003 COIL SL204A PQLQXH152J COIL SL204B PQLQXH152J COIL SL204C PQLQXH152J COIL SL204D PQLQXH152J COIL SL204E PQLQXH152J COIL SL204F PQLQXH152J COIL SL204G PQLQXH152J COIL SL204H PQLQXH152J COIL SL703 G1C1R0ZA0021 COILTH1A PQLE106 COIL STH1B PQLE106 COIL STH1C PQLE106 COIL S

(CRYSTAL OSCILLATORS)X600 PSVCYY0358M3 CRYSTAL OSCILLATOR SX700 H0J479500001 CRYSTAL OSCILLATORX701 PSVCC0019CT CRYSTAL OSCILLATOR S

(FILTERS)FIL701 J0HAAH000003 IC FILTERFIL702 J0HAAH000003 IC FILTERFIL703 J0HAAH000003 IC FILTERFIL704 J0HAAH000003 IC FILTERFIL705 J0HAAH000003 IC FILTERFIL706 J0HAAH000003 IC FILTERL600 J0JCC0000143 IC FILTERL601 J0JCC0000143 IC FILTERL602 J0JCC0000143 IC FILTERL603 J0JCC0000143 IC FILTERL704 J0JCC0000215 IC FILTERL705 J0JCC0000215 IC FILTERL706 J0JCC0000215 IC FILTERL707 J0JCC0000215 IC FILTERL708 J0JCC0000215 IC FILTERL709 J0JCC0000215 IC FILTERL710 J0JCC0000215 IC FILTERL711 J0JCC0000215 IC FILTERL712 J0JCC0000215 IC FILTERL713 J0JCC0000215 IC FILTER

62


Ref.No.


L714 J0JCC0000215 IC FILTERL715 J0JCC0000215 IC FILTERL716 J0JCC0000215 IC FILTERL717 J0JCC0000215 IC FILTERL718 J0JCC0000215 IC FILTERL719 J0JCC0000215 IC FILTERL720 J0JCC0000215 IC FILTERL721 J0JCC0000215 IC FILTERL722 J0JCC0000215 IC FILTERL723 J0JCC0000215 IC FILTERL724 J0JCC0000215 IC FILTERL725 J0JCC0000215 IC FILTERL727 J0JCC0000215 IC FILTERL728 J0JCC0000215 IC FILTERL729 J0JCC0000215 IC FILTERL730 J0JCC0000215 IC FILTERL731 J0JCC0000215 IC FILTERL732 J0JCC0000215 IC FILTERL733 J0JCC0000215 IC FILTERL734 J0JCC0000215 IC FILTERL735 J0JCC0000215 IC FILTERL736 J0JCC0000215 IC FILTERL737 J0JCC0000215 IC FILTERL738 J0JCC0000215 IC FILTERL739 J0JCC0000215 IC FILTERL740 J0JCC0000215 IC FILTERL741 J0JCC0000215 IC FILTERL742 J0JCC0000215 IC FILTERL745 J0JCC0000215 IC FILTER

(FUSES)TH2A D4FAR1700002 FUSETH2B D4FAR1700002 FUSETH2C D4FAR1700002 FUSETH2D D4FAR1700002 FUSETH2E D4FAR1700002 FUSETH2F D4FAR1700002 FUSETH2G D4FAR1700002 FUSETH2H D4FAR1700002 FUSE

(JACKS)CN1A PQJJ1T004Z JACK SCN1B PQJJ1T004Z JACK SCN1C PQJJ1T004Z JACK SCN200A PQJJ1T011Y JACK SCN200B PQJJ1T011Y JACK SCN200C PQJJ1T011Y JACK SCN200D PQJJ1T011Y JACK SCN200E PQJJ1T011Y JACK SCN200F PQJJ1T011Y JACK SCN200G PQJJ1T011Y JACK SCN200H PQJJ1T011Y JACK SCN600 PSJJ1D001Z JACK SCN601 PSJJ1D001Z JACK S

(TRANSFORMERS)T1A G4A1A0000173 TRANSFORMERT1B G4A1A0000173 TRANSFORMERT1C G4A1A0000173 TRANSFORMERT2A G4A1A0000177 TRANSFORMERT2B G4A1A0000177 TRANSFORMERT2C G4A1A0000177 TRANSFORMERT200A ETA14Y85AY TRANSFORMERT200B ETA14Y85AY TRANSFORMERT200C ETA14Y85AY TRANSFORMERT200D ETA14Y85AY TRANSFORMERT200E ETA14Y85AY TRANSFORMERT200F ETA14Y85AY TRANSFORMERT200G ETA14Y85AY TRANSFORMERT200H ETA14Y85AY TRANSFORMERT201 ETE13K24AY TRANSFORMER

(PHOTO ELECTRIC TRANSDUCERS)PC1A PQVIP27011M3 PHOTO COUPER SPC1B PQVIP27011M3 PHOTO COUPER SPC1C PQVIP27011M3 PHOTO COUPER SPC2A PQVIP27011M3 PHOTO COUPER S

Ref.No.


PC2B PQVIP27011M3 PHOTO COUPER SPC2C PQVIP27011M3 PHOTO COUPER SPC4A PQVIP27011M3 PHOTO COUPER SPC4B PQVIP27011M3 PHOTO COUPER SPC4C PQVIP27011M3 PHOTO COUPER SPC5A CNC2S5020LL1 PHOTO COUPERPC5B CNC2S5020LL1 PHOTO COUPERPC5C CNC2S5020LL1 PHOTO COUPER

(RELAYS)RL200A K6B2CGA00121 RELAYRL201A PQSL41Z RELAY SRL201B PQSL41Z RELAY SRL201C PQSL41Z RELAY SRL201D PQSL41Z RELAY SRL201E PQSL41Z RELAY SRL201F PQSL41Z RELAY SRL201G PQSL41Z RELAY SRL201H PQSL41Z RELAY SRL202A K6B2CGA00095 RELAY S

(SWITCHES)SW1 EVQ21409K SPECIAL SWITCHSW2 PQSS2A04W SLIDE SWITCH S

(VARISTORS)SA1A J0LE00000043 VARISTOR (SURGE ABSORBER)SA1B J0LE00000043 VARISTOR (SURGE ABSORBER)SA1C J0LE00000043 VARISTOR (SURGE ABSORBER)SA100 PFRZRA102P6T VARISTOR (SURGE ABSORBER) SZNR2A D4EAB820A005 VARISTORZNR2B D4EAB820A005 VARISTORZNR2C D4EAB820A005 VARISTORZNR200 D4EAB220A005 VARISTORZNR201 D4EAB220A005 VARISTORZNR202 D4EAB220A005 VARISTORZNR203 D4EAB220A005 VARISTOR

(CAPACITORS)C1A PSCU2JW221KR 220PC1B PSCU2JW221KR 220PC1C PSCU2JW221KR 220PC2A ECUV1C474ZFV 0.47C2B ECUV1C474ZFV 0.47C2C ECUV1C474ZFV 0.47C3A ECQE2474KF 0.47 SC3B ECQE2474KF 0.47 SC3C ECQE2474KF 0.47 SC4A ECUV1C474ZFV 0.47C4B ECUV1C474ZFV 0.47C4C ECUV1C474ZFV 0.47C5A F2G1H1000010 10C5B F2G1H1000010 10C5C F2G1H1000010 10C6A F2G1H2R20005 2.2C6B F2G1H2R20005 2.2C6C F2G1H2R20005 2.2C8A ECUV1H102KBV 0.001C8B ECUV1H102KBV 0.001C8C ECUV1H102KBV 0.001C10A ECUV1H820JCV 82PC10B ECUV1H820JCV 82PC10C ECUV1H820JCV 82PC11A ECUV1C683KBV 0.068C11B ECUV1C683KBV 0.068C11C ECUV1C683KBV 0.068C12A ECUV1C563KBV 0.056C12B ECUV1C563KBV 0.056C12C ECUV1C563KBV 0.056C13A ECUV1C563KBV 0.056C13B ECUV1C563KBV 0.056C13C ECUV1C563KBV 0.056C14A ECUV1C563KBV 0.056C14B ECUV1C563KBV 0.056C14C ECUV1C563KBV 0.056C15A ECUV1C563KBV 0.056C15B ECUV1C563KBV 0.056

63


Ref.No.


C15C ECUV1C563KBV 0.056C16A ECUV1H820JCV 82PC16B ECUV1H820JCV 82PC16C ECUV1H820JCV 82PC17A ECUV1H101JCV 100PC17B ECUV1H101JCV 100PC17C ECUV1H101JCV 100PC18A ECUV1H101JCV 100PC18B ECUV1H101JCV 100PC18C ECUV1H101JCV 100PC23A ECUV1H223KBV 0.022 SC23B ECUV1H223KBV 0.022 SC23C ECUV1H223KBV 0.022 SC24A ECUV1H223KBV 0.022 SC24B ECUV1H223KBV 0.022 SC24C ECUV1H223KBV 0.022 SC25A ECUV1H223KBV 0.022 SC25B ECUV1H223KBV 0.022 SC25C ECUV1H223KBV 0.022 SC26A ECUV1H103KBV 0.01C26B ECUV1H103KBV 0.01C26C ECUV1H103KBV 0.01C100 ECUV1H223KBV 0.022 SC101 ECUV1C333KBV 0.033C102 ECUV1H223KBV 0.022 SC103 ECUV1H223KBV 0.022 SC200A ECUV1H103KBV 0.01C200B ECUV1H103KBV 0.01C200C ECUV1H103KBV 0.01C200D ECUV1H103KBV 0.01C200E ECUV1H103KBV 0.01C200F ECUV1H103KBV 0.01C200G ECUV1H103KBV 0.01C200H ECUV1H103KBV 0.01C201A ECUV1H103KBV 0.01C201B ECUV1H103KBV 0.01C201C ECUV1H103KBV 0.01C201D ECUV1H103KBV 0.01C201E ECUV1H103KBV 0.01C201F ECUV1H103KBV 0.01C201G ECUV1H103KBV 0.01C201H ECUV1H103KBV 0.01C202A F2G1C1000014 10C202B F2G1C1000014 10C202C F2G1C1000014 10C202D F2G1C1000014 10C202E F2G1C1000014 10C202F F2G1C1000014 10C202G F2G1C1000014 10C202H F2G1C1000014 10C203A F2G1C1000014 10C203B F2G1C1000014 10C203C F2G1C1000014 10C203D F2G1C1000014 10C203E F2G1C1000014 10C203F F2G1C1000014 10C203G F2G1C1000014 10C203H F2G1C1000014 10C204A F2G1H2R20005 2.2C204B F2G1H2R20005 2.2C204C F2G1H2R20005 2.2C204D F2G1H2R20005 2.2C204E F2G1H2R20005 2.2C204F F2G1H2R20005 2.2C204G F2G1H2R20005 2.2C204H F2G1H2R20005 2.2C205A ECEA1HN4R7S 4.7C205B ECEA1HN4R7S 4.7C205C ECEA1HN4R7S 4.7C205D ECEA1HN4R7S 4.7C205E ECEA1HN4R7S 4.7C205F ECEA1HN4R7S 4.7C205G ECEA1HN4R7S 4.7

Ref.No.


C205H ECEA1HN4R7S 4.7C206A ECUV1C393KBV 0.039 SC206B ECUV1C393KBV 0.039 SC206C ECUV1C393KBV 0.039 SC206D ECUV1C393KBV 0.039 SC206E ECUV1C393KBV 0.039 SC206F ECUV1C393KBV 0.039 SC206G ECUV1C393KBV 0.039 SC206H ECUV1C393KBV 0.039 SC207A ECUV1H103KBV 0.01C207B ECUV1H103KBV 0.01C207C ECUV1H103KBV 0.01C207D ECUV1H103KBV 0.01C207E ECUV1H103KBV 0.01C207F ECUV1H103KBV 0.01C207G ECUV1H103KBV 0.01C207H ECUV1H103KBV 0.01C208A F2G1H1R00013 1C208B F2G1H1R00013 1C208C F2G1H1R00013 1C208D F2G1H1R00013 1C208E F2G1H1R00013 1C208F F2G1H1R00013 1C208G F2G1H1R00013 1C208H F2G1H1R00013 1C209 ECUV1H223KBV 0.022 SC209A ECUV1H103KBV 0.01C209B ECUV1H103KBV 0.01C209C ECUV1H103KBV 0.01C209D ECUV1H103KBV 0.01C209E ECUV1H103KBV 0.01C209F ECUV1H103KBV 0.01C209G ECUV1H103KBV 0.01C209H ECUV1H103KBV 0.01C210A ECUV1H103KBV 0.01C210B ECUV1H103KBV 0.01C210C ECUV1H103KBV 0.01C210D ECUV1H103KBV 0.01C210E ECUV1H103KBV 0.01C210F ECUV1H103KBV 0.01C210G ECUV1H103KBV 0.01C210H ECUV1H103KBV 0.01C211 F1J1E105A008 1C214 ECJ1VB0J225 2.2C600 ECUV1C473KBV 0.047C601 ECUV1C683KBV 0.068C602 ECUV1C104KBV 0.1C603 ECUV1C104KBV 0.1C604 ECUV1H223KBV 0.022 SC605 ECUV1H223KBV 0.022 SC606 ECUV1H332KBV 0.0033C607 ECUV1H682KBV 0.0068 SC608 EEUFC1E101S 100C609 ECUV1H223KBV 0.022 SC610 ECUV1H102KBV 0.001C612 ECUV1C104KBV 0.1C615 ECUV1H471JCV 470P SC616 ECUV1C104KBV 0.1C618 ECUV1C563KBV 0.056C619 ECUV1C563KBV 0.056C620 ECUV1H471JCV 470P SC621 ECUV1C104KBV 0.1C622 ECUV1H471JCV 470P SC623 ECUV1C104KBV 0.1C624 ECUV1H471JCV 470P SC625 ECUV1H471JCV 470P SC626 ECUV1H471JCV 470P SC627 ECUV1C104KBV 0.1C628 ECUV1C223KBV 0.022C629 ECUV1C223KBV 0.022C630 ECUV1C223KBV 0.022C631 ECUV1C223KBV 0.022C634 ECUV1C104KBV 0.1

64


Ref.No.


C635 ECUV1C104KBV 0.1C636 ECUV1C104KBV 0.1C637 ECUV1C104KBV 0.1C640 ECUV1C105KB 1 SC641 ECUV1C105KB 1 SC642 ECUV1H471JCV 470P SC643 ECUV1C105KB 1 SC644 ECUV1C105KB 1 SC645 ECUV1H471JCV 470P SC646 ECUV1C563KBV 0.056C647 ECUV1C563KBV 0.056C648 ECUV1C563KBV 0.056C649 ECUV1C563KBV 0.056C650 ECUV1H562KBV 0.0056C651 ECUV1H562KBV 0.0056C652 ECUV1H471JCV 470P SC653 ECUV1H471JCV 470P SC654 ECUV1H471JCV 470P SC655 ECUV1H471JCV 470P SC656 ECUV1C104KBV 0.1C657 ECUV1C104KBV 0.1C658 PSCUV2EW223K 0.022 SC659 ECUV1C104KBV 0.1C660 ECUV1C104KBV 0.1C661 ECUV1H223KBV 0.022 SC662 ECUV1C104KBV 0.1C663 ECUV1H223KBV 0.022 SC664 ECUV1H223KBV 0.022 SC665 ECUV1H223KBV 0.022 SC666 ECUV1H223KBV 0.022 SC667 ECUV1H223KBV 0.022 SC668 ECUV1H223KBV 0.022 SC669 ECUV1H223KBV 0.022 SC670 ECUV1H223KBV 0.022 SC672 ECUV1H223KBV 0.022 SC673 ECUV1H223KBV 0.022 SC674 ECUV1H223KBV 0.022 SC675 ECUV1H471JCV 470P SC676 ECUV1H822KBV 0.0082 SC677 ECUV1C333KBV 0.033C679 ECUV1C104KBV 0.1C680 ECUV1C104KBV 0.1C681 ECUV1C104KBV 0.1C682 ECUV1H223KBV 0.022 SC683 ECUV1C104KBV 0.1C684 ECUV1H471JCV 470P SC685 ECUV1C104KBV 0.1C700 EEUFC1E101S 100C701 EEUFC1E101S 100C702 EEUFC1E101S 100C703 F1J1E105A008 1C704 ECUV1C474ZFV 0.47C705 ECEA1HN2R2S 2.2C707 ECUV1A105ZFV 1C708 ECUV1C823KBV 0.082C709 ECUV1C823KBV 0.082C710 ECUV1C104ZFV 0.1C711 ECUV1H223KBV 0.022 SC712 ECUV1H223KBV 0.022 SC713 ECUV1H180JCV 18PC714 ECUV1H220JCV 22PC715 ECUV1H223KBV 0.022 SC716 ECJ1VB0J225 2.2C717 F1J1E105A008 1C718 ECUV1C224ZFV 0.22C719 ECUV1H103KBV 0.01C720 ECUV1H330JCV 33PC721 ECJ1VC1H050C 5PC722 ECUV1C104KBV 0.1C723 ECUV1C104KBV 0.1C724 ECUV1C104ZFV 0.1C725 PQCUV1A225ZF 2.2 SC726 ECUV1A105ZFV 1

Ref.No.


C727 ECUV1C104KBV 0.1C728 ECUV1C104KBV 0.1C729 ECUV1C104ZFV 0.1C730 PQCUV1A225ZF 2.2 SC731 ECUV1A105ZFV 1C732 ECUV1C104ZFV 0.1C733 ECJ1VB1H221K 220PC734 ECUV1C104ZFV 0.1C735 ECUV1C104ZFV 0.1C736 ECUV1C104ZFV 0.1C737 ECUV1C104ZFV 0.1C738 ECUV1C104ZFV 0.1C739 ECUV1C104ZFV 0.1C740 PQCUV1A225ZF 2.2 SC741 ECUV1A105ZFV 1C742 ECUV1C104ZFV 0.1C743 ECUV1C104ZFV 0.1C744 ECUV1C104ZFV 0.1C745 ECUV1C104ZFV 0.1C746 ECUV1C104ZFV 0.1C747 ECUV1C104ZFV 0.1C748 ECUV1C104ZFV 0.1C749 ECUV1C104ZFV 0.1C750 ECUV1C104ZFV 0.1C751 PQCUV1A225ZF 2.2 SC752 ECUV1A105ZFV 1C753 ECUV1C104ZFV 0.1C754 ECUV1C104ZFV 0.1C755 ECUV1C104ZFV 0.1C756 ECUV1C104ZFV 0.1C758 PQCUV1A225ZF 2.2 SC759 ECUV1A105ZFV 1C760 ECUV1C104ZFV 0.1C761 ECUV1C104ZFV 0.1C762 ECUV1C104ZFV 0.1C763 ECUV1C104ZFV 0.1C764 F2G1H3R30006 3.3 SC765 ECUV1C104ZFV 0.1C766 F2G1H3R30006 3.3 SC767 ECUV1C104ZFV 0.1C768 F2G1H3R30006 3.3C769 ECUV1A105ZFV 1C770 ECUV1A105ZFV 1C771 ECUV1C333KBV 0.033C772 PQCUV1A225ZF 2.2 SC773 ECUV1A105ZFV 1C776 F4D257040001 0.7C777 F4D257040001 0.7C778 F2G0J2200006 22C779 F2G0J2200006 22C801 ECUV1H103KBV 0.01C802 ECUV1H103KBV 0.01C803 ECUV1H103KBV 0.01C804 ECUV1H103KBV 0.01C805 ECUV1H103KBV 0.01C806 ECUV1H103KBV 0.01C807 ECUV1H103KBV 0.01C808 ECUV1H103KBV 0.01C809 ECUV1H103KBV 0.01C810 ECUV1H103KBV 0.01C811 ECUV1H103KBV 0.01C812 ECUV1H103KBV 0.01C813 ECUV1H103KBV 0.01C814 ECUV1H103KBV 0.01C815 ECUV1H103KBV 0.01C816 ECUV1H103KBV 0.01C817 ECUV1H103KBV 0.01C818 ECUV1H103KBV 0.01C819 ECUV1H103KBV 0.01C820 ECUV1H103KBV 0.01C821 ECUV1H103KBV 0.01C822 ECUV1H103KBV 0.01C823 ECUV1H103KBV 0.01

65


Ref.No.


C824 ECUV1H103KBV 0.01C825 ECUV1H103KBV 0.01C826 ECUV1H103KBV 0.01C827 ECUV1H103KBV 0.01C828 ECUV1H103KBV 0.01C829 ECUV1H103KBV 0.01C830 ECUV1H103KBV 0.01C831 ECUV1H103KBV 0.01C832 ECUV1H103KBV 0.01C833 ECUV1H103KBV 0.01C834 ECUV1H103KBV 0.01C835 ECUV1H103KBV 0.01C836 ECUV1H103KBV 0.01C837 ECUV1H103KBV 0.01C838 ECUV1H103KBV 0.01C839 ECUV1H103KBV 0.01C840 ECUV1H103KBV 0.01C841 ECUV1H103KBV 0.01C842 ECUV1H103KBV 0.01C843 ECUV1H103KBV 0.01C844 ECUV1H103KBV 0.01C845 ECUV1H103KBV 0.01C846 ECUV1H103KBV 0.01C847 ECUV1H103KBV 0.01C848 ECUV1H103KBV 0.01C849 ECUV1H103KBV 0.01C850 ECUV1H103KBV 0.01C851 ECUV1H103KBV 0.01C852 ECUV1H103KBV 0.01C853 ECUV1H103KBV 0.01C854 ECUV1H103KBV 0.01C855 ECUV1H103KBV 0.01C856 ECUV1H103KBV 0.01C857 ECUV1H103KBV 0.01C858 ECUV1H103KBV 0.01C859 ECUV1H103KBV 0.01C860 ECUV1H103KBV 0.01C861 ECUV1H103KBV 0.01C862 ECUV1H103KBV 0.01C863 ECUV1H103KBV 0.01C864 ECUV1H103KBV 0.01C865 ECUV1H103KBV 0.01C866 ECUV1H103KBV 0.01C868 ECUV1H103KBV 0.01C869 ECUV1H103KBV 0.01C870 ECUV1H103KBV 0.01C871 ECUV1H103KBV 0.01C872 ECUV1H103KBV 0.01C873 ECUV1H103KBV 0.01C874 ECUV1H103KBV 0.01C875 ECUV1H103KBV 0.01C876 ECUV1H103KBV 0.01C877 ECUV1H103KBV 0.01C878 ECUV1H103KBV 0.01C879 ECUV1H103KBV 0.01C880 ECUV1H103KBV 0.01C881 ECUV1H103KBV 0.01C882 ECUV1H103KBV 0.01C883 ECUV1H103KBV 0.01C884 ECUV1H103KBV 0.01C885 ECUV1H103KBV 0.01C886 ECUV1H103KBV 0.01C887 ECUV1H103KBV 0.01C888 ECUV1H103KBV 0.01C889 ECUV1H103KBV 0.01C890 ECUV1H103KBV 0.01C893 ECUV1H103KBV 0.01C894 ECUV1H103KBV 0.01C895 ECUV1H103KBV 0.01C896 ECUV1H103KBV 0.01C897 ECUV1H103KBV 0.01C898 ECUV1H103KBV 0.01C899 ECUV1H103KBV 0.01

Ref.No.


C900 ECUV1H103KBV 0.01C901 ECUV1H103KBV 0.01C902 ECUV1H103KBV 0.01C903 ECUV1H103KBV 0.01C904 ECUV1H103KBV 0.01C905 ECUV1H103KBV 0.01C906 ECUV1H103KBV 0.01C907 ECUV1H103KBV 0.01C908 ECUV1H103KBV 0.01C909 ECUV1H103KBV 0.01C910 ECUV1H103KBV 0.01C911 ECUV1H103KBV 0.01C912 ECUV1H103KBV 0.01C913 ECUV1H103KBV 0.01C914 ECUV1H103KBV 0.01C915 ECUV1H103KBV 0.01C951 ECUV1H103KBV 0.01C952 ECUV1H103KBV 0.01C953 ECUV1H103KBV 0.01C954 ECUV1H103KBV 0.01C955 ECUV1H103KBV 0.01C956 ECUV1H103KBV 0.01C957 ECUV1H103KBV 0.01C958 ECUV1H103KBV 0.01C960 ECUV1H103KBV 0.01C961 ECUV1H103KBV 0.01C962 ECUV1H103KBV 0.01C963 ECUV1H103KBV 0.01C964 ECUV1H103KBV 0.01C965 ECUV1H103KBV 0.01C966 ECUV1H103KBV 0.01C977 ECUV1H103KBV 0.01C978 ECUV1H103KBV 0.01C979 ECUV1H103KBV 0.01C980 ECUV1H103KBV 0.01C985 ECUV1C104KBV 0.1C989 ECUV1H223KBV 0.022 SC991 ECUV1H103KBV 0.01C992 ECUV1H103KBV 0.01C993 ECUV1H103KBV 0.01C994 ECUV1H103KBV 0.01C995 PQCUV1H104ZF 0.1

(RESISTORS)J2A PQ4R18XJ000 0 SJ2B PQ4R18XJ000 0 SJ2C PQ4R18XJ000 0 SJ5A PQ4R10XJ000 0 SJ5B PQ4R10XJ000 0 SJ5C PQ4R10XJ000 0 SJ108 PQ4R18XJ000 0 SJ603 ERJ3GEY0R00 0J607 ERJ3GEY0R00 0J609 ERJ3GEY0R00 0J700 PQ4R18XJ000 0 SJ701 PQ4R10XJ000 0 SJ709 PQ4R18XJ000 0 SJ710 PQ4R18XJ000 0 SJ711 PQ4R18XJ000 0 SJ712 ERJ3GEY0R00 0J714 ERJ3GEY0R00 0J715 ERJ3GEY0R00 0J717 PQ4R18XJ000 0 SL746 PQ4R10XJ000 0 SL747 PQ4R10XJ000 0 SL748 PQ4R10XJ000 0 SR1A ERJ3GEYJ822 8.2KR1B ERJ3GEYJ822 8.2KR1C ERJ3GEYJ822 8.2KR2A PQ4R18XJ220 22 SR2B PQ4R18XJ220 22 SR2C PQ4R18XJ220 22 SR4A PQ4R10XJ681 680 SR4B PQ4R10XJ681 680 S

66


Ref.No.


R4C PQ4R10XJ681 680 SR5A ERJ1WYJ682 6.8KR5B ERJ1WYJ682 6.8KR5C ERJ1WYJ682 6.8KR6A ERJ3GEYJ822 8.2KR6B ERJ3GEYJ822 8.2KR6C ERJ3GEYJ822 8.2KR7A ERJ3GEYJ392 3.9KR7B ERJ3GEYJ392 3.9KR7C ERJ3GEYJ392 3.9KR8A PQ4R10XJ000 0 SR8B PQ4R10XJ000 0 SR8C PQ4R10XJ000 0 SR9A ERJ8GEYJ390 39R9B ERJ8GEYJ390 39R9C ERJ8GEYJ390 39R10A PQ4R10XJ682 6.8K SR10B PQ4R10XJ682 6.8K SR10C PQ4R10XJ682 6.8K SR110 ERJ3GEYJ103 10KR11A ERJ3GEYJ103 10KR11B ERJ3GEYJ103 10KR11C ERJ3GEYJ103 10KR12A PQ4R10XJ000 0 SR12B PQ4R10XJ000 0 SR12C PQ4R10XJ000 0 SR14A PQ4R10XJ822 8.2K SR14B PQ4R10XJ822 8.2K SR14C PQ4R10XJ822 8.2K SR15A ERJ3GEYJ101 100R15B ERJ3GEYJ101 100R15C ERJ3GEYJ101 100R16A ERJ3GEY0R00 0R16B ERJ3GEY0R00 0R16C ERJ3GEY0R00 0R17A ERJ3GEYF122 1.2K SR17B ERJ3GEYF122 1.2K SR17C ERJ3GEYF122 1.2K SR18A ERJ3GEYJ103 10KR18B ERJ3GEYJ103 10KR18C ERJ3GEYJ103 10KR20A ERJ3GEYF122 1.2K SR20B ERJ3GEYF122 1.2K SR20C ERJ3GEYF122 1.2K SR21A ERJ3GEY0R00 0R21B ERJ3GEY0R00 0R21C ERJ3GEY0R00 0R22A ERJ3EKF5600 560R22B ERJ3EKF5600 560R22C ERJ3EKF5600 560R23A ERJ3EKF1001 1KR23B ERJ3EKF1001 1KR23C ERJ3EKF1001 1KR24A ERJ3EKF1003 100KR24B ERJ3EKF1003 100KR24C ERJ3EKF1003 100KR25A ERJ3EKF1003 100KR25B ERJ3EKF1003 100KR25C ERJ3EKF1003 100KR26A ERJ3GEYJ304 300KR26B ERJ3GEYJ304 300KR26C ERJ3GEYJ304 300KR27A ERJ3GEYJ304 300KR27B ERJ3GEYJ304 300KR27C ERJ3GEYJ304 300KR28A ERJ3GEYJ304 300KR28B ERJ3GEYJ304 300KR28C ERJ3GEYJ304 300KR29A ERJ3GEYJ103 10KR29B ERJ3GEYJ103 10KR29C ERJ3GEYJ103 10KR30A ERJ3GEYJ103 10KR30B ERJ3GEYJ103 10K

Ref.No.


R30C ERJ3GEYJ103 10KR31A ERJ3GEYJ304 300KR31B ERJ3GEYJ304 300KR31C ERJ3GEYJ304 300KR34A ERJ3EKF1003 100KR34B ERJ3EKF1003 100KR34C ERJ3EKF1003 100KR35A ERJ3EKF1003 100KR35B ERJ3EKF1003 100KR35C ERJ3EKF1003 100KR37A ERJ3GEYJ103 10KR37B ERJ3GEYJ103 10KR37C ERJ3GEYJ103 10KR38A ERJ3GEY0R00 0R38B ERJ3GEY0R00 0R38C ERJ3GEY0R00 0R39A ERJ3GEYF122 1.2K SR39B ERJ3GEYF122 1.2K SR39C ERJ3GEYF122 1.2K SR40A ERJ3GEYF122 1.2K SR40B ERJ3GEYF122 1.2K SR40C ERJ3GEYF122 1.2K SR41A ERJ3GEYJ151 150R41B ERJ3GEYJ151 150R41C ERJ3GEYJ151 150R42A ERJ3GEYF122 1.2K SR42B ERJ3GEYF122 1.2K SR42C ERJ3GEYF122 1.2K SR43A ERJ3GEY0R00 0R43B ERJ3GEY0R00 0R43C ERJ3GEY0R00 0R45A ERJ3GEY0R00 0R45B ERJ3GEY0R00 0R45C ERJ3GEY0R00 0R46A ERJ3EKF2701 2.7KR46B ERJ3EKF2701 2.7KR46C ERJ3EKF2701 2.7KR47A ERJ3GEYJ473 47KR47B ERJ3GEYJ473 47KR47C ERJ3GEYJ473 47KR49A ERJ3GEYJ473 47KR49B ERJ3GEYJ473 47KR49C ERJ3GEYJ473 47KR50A ERJ3GEYJ473 47KR50B ERJ3GEYJ473 47KR50C ERJ3GEYJ473 47KR51A ERJ3GEYJ104 100KR51B ERJ3GEYJ104 100KR51C ERJ3GEYJ104 100KR52A ERJ3GEYJ272 2.7KR52B ERJ3GEYJ272 2.7KR52C ERJ3GEYJ272 2.7KR53A ERJ3GEYJ103 10KR53B ERJ3GEYJ103 10KR53C ERJ3GEYJ103 10KR103 ERJ3GEYJ103 10KR104 ERJ3GEYJ331 330R105 ERJ3GEYJ331 330R106 ERJ3GEYJ331 330R107 ERJ3GEYJ331 330R108 ERJ3GEYJ331 330R109 ERJ3GEYJ331 330R200A ERJ3GEYJ682 6.8KR200B ERJ3GEYJ682 6.8KR200C ERJ3GEYJ682 6.8KR200D ERJ3GEYJ682 6.8KR200E ERJ3GEYJ682 6.8KR200F ERJ3GEYJ682 6.8KR200G ERJ3GEYJ682 6.8KR200H ERJ3GEYJ682 6.8KR201A ERJ3GEYJ682 6.8KR201B ERJ3GEYJ682 6.8KR201C ERJ3GEYJ682 6.8K

67


Ref.No.


R201D ERJ3GEYJ682 6.8KR201E ERJ3GEYJ682 6.8KR201F ERJ3GEYJ682 6.8KR201G ERJ3GEYJ682 6.8KR201H ERJ3GEYJ682 6.8KR202A ERJ14YJ220 22R202B ERJ14YJ220 22R202C ERJ14YJ220 22R202D ERJ14YJ220 22R202E ERJ14YJ220 22R202F ERJ14YJ220 22R202G ERJ14YJ220 22R202H ERJ14YJ220 22R203A ERJ14YJ220 22R203B ERJ14YJ220 22R203C ERJ14YJ220 22R203D ERJ14YJ220 22R203E ERJ14YJ220 22R203F ERJ14YJ220 22R203G ERJ14YJ220 22R203H ERJ14YJ220 22R204A ERJ14YJ680 68R204B ERJ14YJ680 68R204C ERJ14YJ680 68R204D ERJ14YJ680 68R204E ERJ14YJ680 68R204F ERJ14YJ680 68R204G ERJ14YJ680 68R204H ERJ14YJ680 68R205A ERJ14YJ680 68R205B ERJ14YJ680 68R205C ERJ14YJ680 68R205D ERJ14YJ680 68R205E ERJ14YJ680 68R205F ERJ14YJ680 68R205G ERJ14YJ680 68R205H ERJ14YJ680 68R206A ERJ1WYJ102 1K SR206B ERJ1WYJ102 1K SR206C ERJ1WYJ102 1K SR206D ERJ1WYJ102 1K SR206E ERJ1WYJ102 1K SR206F ERJ1WYJ102 1K SR206G ERJ1WYJ102 1K SR206H ERJ1WYJ102 1K SR207A ERJ3GEYJ333 33KR207B ERJ3GEYJ333 33KR207C ERJ3GEYJ333 33KR207D ERJ3GEYJ333 33KR207E ERJ3GEYJ333 33KR207F ERJ3GEYJ333 33KR207G ERJ3GEYJ333 33KR207H ERJ3GEYJ333 33KR208A ERJ3GEYJ563 56KR208B ERJ3GEYJ563 56KR208C ERJ3GEYJ563 56KR208D ERJ3GEYJ563 56KR208E ERJ3GEYJ563 56KR208F ERJ3GEYJ563 56KR208G ERJ3GEYJ563 56KR208H ERJ3GEYJ563 56KR209A ERJ3GEYJ153 15KR209B ERJ3GEYJ153 15KR209C ERJ3GEYJ153 15KR209D ERJ3GEYJ153 15KR209E ERJ3GEYJ153 15KR209F ERJ3GEYJ153 15KR209G ERJ3GEYJ153 15KR209H ERJ3GEYJ153 15KR210A ERJ3GEYJ333 33KR210B ERJ3GEYJ333 33KR210C ERJ3GEYJ333 33KR210D ERJ3GEYJ333 33K

Ref.No.


R210E ERJ3GEYJ333 33KR210F ERJ3GEYJ333 33KR210G ERJ3GEYJ333 33KR210H ERJ3GEYJ333 33KR211A ERJ3GEYJ123 12KR211B ERJ3GEYJ123 12KR211C ERJ3GEYJ123 12KR211D ERJ3GEYJ123 12KR211E ERJ3GEYJ123 12KR211F ERJ3GEYJ123 12KR211G ERJ3GEYJ123 12KR211H ERJ3GEYJ123 12KR215A ERJ3GEYJ473 47KR215B ERJ3GEYJ473 47KR215C ERJ3GEYJ473 47KR215D ERJ3GEYJ473 47KR215E ERJ3GEYJ473 47KR215F ERJ3GEYJ473 47KR215G ERJ3GEYJ473 47KR215H ERJ3GEYJ473 47KR216A ERJ3GEYJ103 10KR216B ERJ3GEYJ103 10KR216C ERJ3GEYJ103 10KR216D ERJ3GEYJ103 10KR216E ERJ3GEYJ103 10KR216F ERJ3GEYJ103 10KR216G ERJ3GEYJ103 10KR216H ERJ3GEYJ103 10KR218A ERJ3GEYJ103 10KR218B ERJ3GEYJ103 10KR218C ERJ3GEYJ103 10KR218D ERJ3GEYJ103 10KR218E ERJ3GEYJ103 10KR218F ERJ3GEYJ103 10KR218G ERJ3GEYJ103 10KR218H ERJ3GEYJ103 10KR219A ERJ3GEYJ102 1KR219B ERJ3GEYJ102 1KR219C ERJ3GEYJ102 1KR219D ERJ3GEYJ102 1KR219E ERJ3GEYJ102 1KR219F ERJ3GEYJ102 1KR219G ERJ3GEYJ102 1KR219H ERJ3GEYJ102 1KR220A PQ4R10XJ271 270 SR220B PQ4R10XJ271 270 SR220C PQ4R10XJ271 270 SR220D PQ4R10XJ271 270 SR220E PQ4R10XJ271 270 SR220F PQ4R10XJ271 270 SR220G PQ4R10XJ271 270 SR220H PQ4R10XJ271 270 SR221A ERJ3GEYJ103 10KR221B ERJ3GEYJ103 10KR221C ERJ3GEYJ103 10KR221D ERJ3GEYJ103 10KR221E ERJ3GEYJ103 10KR221F ERJ3GEYJ103 10KR221G ERJ3GEYJ103 10KR221H ERJ3GEYJ103 10KR225 ERJ3GEYJ103 10KR225A ERJ3GEYJ103 10KR225B ERJ3GEYJ103 10KR225C ERJ3GEYJ103 10KR225D ERJ3GEYJ103 10KR225E ERJ3GEYJ103 10KR225F ERJ3GEYJ103 10KR225G ERJ3GEYJ103 10KR225H ERJ3GEYJ103 10KR226 ERJ3GEYJ103 10KR227 ERJ3GEYJ682 6.8KR228 ERJ3GEYJ682 6.8KR229 ERJ3GEY0R00 0

68


Ref.No.


R231 ERJ3GEYJ273 27KR232 ERJ3GEYJ273 27KR235 ERJ3GEYJ222 2.2KR237 ERJ3GEYJ472 4.7KR238 ERJ3GEYJ102 1KR239 ERJ3GEYJ473 47KR240 ERJ3GEYJ101 100R241 ERJ3GEYJ472 4.7KR511 ERJ3GEYJ272 2.7KR512 ERJ3GEYJ104 100KR516 ERJ3GEYJ104 100KR517 ERJ3GEYJ223 22KR518 ERJ3GEYJ273 27KR520 ERJ3GEYJ471 470R521 ERJ3GEYJ393 39KR525 ERJ3GEYJ224 220KR526 ERJ3GEYJ124 120KR527 ERJ3GEYJ333 33KR528 ERJ3GEYJ223 22KR529 ERJ3GEYJ683 68KR530 ERJ3GEYJ102 1KR531 ERJ3GEYJ473 47KR532 ERJ3GEY0R00 0R534 ERJ3GEYJ223 22KR535 ERJ3GEYJ563 56KR536 ERJ3GEYJ104 100KR537 ERJ3GEY0R00 0R538 ERJ3GEYJ393 39KR539 ERJ3GEYJ153 15KR540 ERJ3GEYJ223 22KR541 ERJ3GEYJ223 22KR542 ERJ3GEY0R00 0R543 ERJ3GEY0R00 0R544 ERJ3GEY0R00 0R545 ERJ3GEY0R00 0R546 ERJ3GEYJ103 10KR547 ERJ3GEYJ223 22KR548 ERJ3GEYJ123 12KR549 ERJ3GEYJ472 4.7KR550 ERJ3GEYJ682 6.8KR551 ERJ3GEYJ682 6.8KR552 ERJ3GEYJ123 12KR553 ERJ3GEYJ682 6.8KR554 ERJ3GEYJ682 6.8KR556 ERJ3GEYJ104 100KR557 ERJ3GEYJ104 100KR558 ERJ3GEY0R00 0R559 ERJ3GEYJ122 1.2KR560 ERJ1WYJ102 1K SR561 ERJ3GEY0R00 0R562 ERJ3GEYJ27

s m tes_tem824pd.pdf

Documents

main board of kx

mainboard of kx

extension kxtes824pd

music kxtes824pd

dial tone kxtes824pd

extension sub board

main unit kxtes824pdkx

dial tone sub board