saa sucs - command access€¦ · saa sucs visit our website for more details u.s. customer support...
TRANSCRIPT
![Page 1: SAA SUCS - Command Access€¦ · SAA SUCS Visit our website for more details U.S. Customer Support 1-888-622-2377 Canada Customer Support 1-855-823-3002 The SGTREXKIT-M-ED is a field](https://reader034.vdocument.in/reader034/viewer/2022042212/5eb5448343db7d5a0a28af14/html5/thumbnails/1.jpg)
SGTREXKIT-M-ED
Doc # 20082_A
I N S T A L L A T I O N I N S T R U C T I O N S
Visit our website for more detailswww.CommandAccess.com
U.S. Customer Support1-888-622-2377
Canada Customer Support1-855-823-3002
The SGTREXKIT-M-ED is a field installable Request-to-Exit switch for SLP-UL-M-KIT, Sargent motorized latch pullback kit. The switch is SPDT (single pull, double throw).
K it I nc ludesA. 1 -REX stickerB. 2 - Phillips head screwsC. 2 - WashersD. 1 - Cable tie mountE. 1 - REX switch with 4’ LeadF. 1 - Cable tie
Tools Required• Phillips head screwdriver
B.
A.
C.
E.
D.
F.
![Page 2: SAA SUCS - Command Access€¦ · SAA SUCS Visit our website for more details U.S. Customer Support 1-888-622-2377 Canada Customer Support 1-855-823-3002 The SGTREXKIT-M-ED is a field](https://reader034.vdocument.in/reader034/viewer/2022042212/5eb5448343db7d5a0a28af14/html5/thumbnails/2.jpg)
• Remove end cap and filler plate.
• Line REX switch up with activating lever
to the left & install both screws. Do not
overtighten. When device is activated
motor block will move forward & trigger
switch.
• Locate two pre-tapped holes on motor
bracket.
• Place small plastic washers (C) on screws
(B) provided.
Activating Lever
• Test make sure switch is making proper
contact depress push pad.
![Page 3: SAA SUCS - Command Access€¦ · SAA SUCS Visit our website for more details U.S. Customer Support 1-888-622-2377 Canada Customer Support 1-855-823-3002 The SGTREXKIT-M-ED is a field](https://reader034.vdocument.in/reader034/viewer/2022042212/5eb5448343db7d5a0a28af14/html5/thumbnails/3.jpg)
• Test switch to confirm proper operation.
After replace filler plate & end cap.
• Putting zip tie through cable tie mount.
Secure wires & clip off excess tie.
• While push pad is depressed check to
make sure motor block is activating
switch.
• Run wires down along the side of motor.
• Place sticky side of the cable tie mount
onto the inside of the baserail.
![Page 4: SAA SUCS - Command Access€¦ · SAA SUCS Visit our website for more details U.S. Customer Support 1-888-622-2377 Canada Customer Support 1-855-823-3002 The SGTREXKIT-M-ED is a field](https://reader034.vdocument.in/reader034/viewer/2022042212/5eb5448343db7d5a0a28af14/html5/thumbnails/4.jpg)
SGTREXKIT-M-ED
Doc # 20082_A
Visit our website for more detailswww.CommandAccess.com
U.S. Customer Support1-888-622-2377
Canada Customer Support1-855-823-3002
T E C H N I C A L I N F O R M A T I O N
Troubleshooting & Diagnostics
Specifications• Rating:
• Configuration:
5A @120VAC
Green - Common (C)
Blue - Normally Open (NO)
Gray - Normally Closed (NC)
If switch does not trigger correctly. Check activating lever arm on switch & re-adjust to make
sure it is making good contact with motor block when it moves forward.