sample2 drawing
TRANSCRIPT
NOTES: 1. All welds shall be neat in appearance, free of slag and other defects. 2. Vessel to be cleaned of scale, oil, weld splatter and all foreign material prior to hydrostatic test. 3. Remove all sharp edges on nozzles (1/8" minimum radius) 4. All Nozzles to support nominal loads only. 5. Vessel weight ( approx. dry ) 350 lbs Vessel weight ( approx. test ) 500 lbs 6. Capacity 3 cu.ft. 7. Fluid: air
Certified byXYZ Vessel Corp.
Item Qty
Description
Bill of MaterialsMaterial
UW50.18~CRN
(Name of Manufacturer)
200
Max. allowable working pressure (MAWP)
psi (kPa) at
300
F (C)
-
Max. allowable external working pressure
psi (kPa) at
-
F (C)
-20
Minimum Design Metal Temperature (MDMT)
F (C) at
200 psi (kPa)
1 2 3 4 5 6 7 8 9 10
1 2 1 1 2 1 2 4 1 1
PIPE: 12" SCH. STD PIPE CAP: 12" SCH. STD PIPE: 4" SCH. 40 FLANGE: 4" 150# RSFO HALF CPLG: 2" 3000# NPT HALF CPLG: 1/2" 3000# NPT PLATE: 3/8" THICK PLATE: 7-1/2" x 2" x 3/8" MTG REINFORCEMENT CODE NAMEPLATE BRACKET CODE NAMEPLATE
SA-106B SA-234 WPB SA-106B SA-105 SA-105 SA-105 SA/CSA-G40.21 44W SA/CSA-G40.21 44W SA/CSA-G40.21 44W STAINLESS
N-0000Manufacturer's serial number
6.00
36.00 18.00 N1 1 8.00 0.381/8 1/2 4 PLC
4
3
e Sa mN3 120
O pl(14.38) REF
12.75 OD N2
1.00 REF
nl
yYear built
~
Design Data
1/4
TYP
5/8" HOLE TYP
12.00 (8.81) REF
N4 6 28.00 9 10
1/4
TYP
5
2
8
7
En
1.25
2.00
7.00 11.00
2.25
31.50 34.00 SIDE ELEVATION
Design Code: ASME Code Section VIII Division 1, 2004 Edition, A06 Design Pressure Internal: 200 psi @ 300F MAWP: 200 psi Design Pressure External: N/A MDMT: -20F @ 200 psi Hydro Test Pressure: 260 psi @ ambient for 1/2 Hour PWHT: None Radiography: None Corrosion Allowance: 0" Impact Test: Exempt per UG-20(f)
g
END VIEW2 1 0REV
PV
Updates Updates ReleaseDESCRIPTION
Aug 19/08 July 9/08 June 23/08
BEM BEM BEMINITIALS
REVISION HISTORY
DATE
PVEngnt nt
Pressure Vessel Engineering
120 Randall Drive, Suite B, Waterloo, Ontario, N2V 1C6 P: 519.880.9808 F: 519.880.9810 http://www.pveng.com [email protected]
TYP.
45
Nozzle Mark Size Qty
Flange
Service
Type
Welds Leg Leg 41 421 5 5 4" 16"
Leg 431 4"
Flange Weld SB (w)3 8"
Nozzle
Nozzle Schedule
Outside InsideUW-16.1 (c)t
Inside
Nozzle
t Leg41
Full Pen.
Full t Pen. Leg41 t Outside ShellProj
Leg43
TITLE
PVE SAMPLE VESSELJOB ID DRAWING NO REV
N1 N2 N3 N4
4" 2" 2" 1/2"
1 1 1 1
VENT INLET OUTLET DRAIN
II I I I
16" 1 4"
-
-
-
0.216" -
SB
w w
SIZE
BSCALE
Sample 2 1:8
Sample 2SHEET
2 1 of 1
TYP. CIRC. SEAM
TYPE I
SLIP ON FLANGE
UW-16.1 (c) with inside projection
TYPE II