saturn cutoff led and saturn 2 cutoff led installation · pdf file ·...

of 5 (Rev. 07/14)

SACL_INST_v3.3

Please Note: Disconnect electricity to fixture before working. To be performed by trained personnel only. It is the responsibility of the installer to ensure all electri-cal, mechanical, and thermal compatibility of the installation site and luminaires prior to installation. Please observe all relevant building codes and regulations. Keep these instructions after unpacking fixture. For outdoor use only. For detailed spec sheets and more information on this and our full range of products, please visit our website at selux.us. Warranty information: http://www.selux.us/en/resources/terms-and-warranty.html

Selux Corporation © 2014, T 845-834-1400, 800-735-8927, F 845-834-1401, www.selux.us

LED Radiation. Do NOT stare into Beam. Can cause eye damage. Do not operate while LEDs are exposed.

CAUTIONHazardous voltage.

Only work on de-engergized equipment. Disconnect power before wiring fixture.

Contact will cause electric shock or burn.

DANGERDo not touch LEDMay damage deviceObserve precautions for handling electrostatic sensitive devices.

NOTICE

4 1/

8" [1

05m

m]

Fitte

r Dep

th, R

ef

3 1/8" [79mm]Minimum Pole I.D.

10 5

/16"

[262

mm

]D

river

Dep

th

Saturn Cutoff LED and Saturn 2 Cutoff LED

1. Run Feed Cord from Luminaire into top of Pole (fixture does not need to be opened; it ships ready to install).

2. Place Luminaire onto Pole.3. Aim the fixture as intended. Always position Street Side Label at street

side (see label next to glass).4. Level and secure into place by tightening (2) Set Screws with Allen

Wrench. 5. Loosen Handhole Screws and remove Handhole Cover. Connect Feed

Cord from Luminaire to Line Voltage Feed (by others). See wiring on page 4 for proper installation. Be sure not to pinch wires during installation.

6. Replace Handhole Cover and test fixture.

Luminaire

Feed Cord (from Luminaire)

Pole

Set Screws (4mm Allen Wrench)

Installation Instructions: Post Top

Tools Required (not included) 4mm Allen Wrench #10 Spanner Head Driver

Handhole Cover

For details and spec sheet for Saturn Cutoff LED, scan here.

Pole

SACL

SAC2L (shown for reference)

#10 Spanner Head Driver

of 5 (Rev. 07/14)

SACL_INST_v3.3








NOTICE

Saturn Cutoff LED and Saturn 2 Cutoff LEDGear Tray Maintenance

Tools Required (not included) #10 Spanner Head DriverPhillips Head Screwdriver

3


1. Disconnect Power.2. Loosen Handhole screws and remove Handhole Cover (not shown).

Disconnect luminaire Feed Cord from Line Voltage Feed (not shown).3. Twist lower cover counter-clockwise to remove cover.4. Loosen (2) M6 pan head screws (do not remove screws).5. Turn gear tray counter-clockwise and lift Gear Tray Assembly out of

pole, just enough to expose terminal blocks. 6. Disconnect white, black and green wires coming from side tubes.

Remove Gear Tray Assembly from pole along with the attached Feed Cord from Luminaire.

7. Run Feed Cord from the new Gear Tray Assembly into Pole. 8. Place New Gear Tray Assembly partly into pole exposing the terminal

blocks. Reconnect wires from side tubes according to wiring shown on page.

9. Reinstall Gear Tray Assembly. Tighten (2) M6 pan head screws. Reinstall lower cover.

10. Connect the new Feed Cord from Luminaire to Line Voltage Feed. 11. Replace Handhole Cover and test Luminaire.

4Top Terminal

Block

Wires from Side Table

Bottom Terminal

Block

Top Terminal Block

Connect WHITE Wire from Side Tubes with RED Wirefrom Gear Tray Assembly

WHITEBLACK

REDBLACK

WHITEBLACKGREEN

Wires from Side Tube

Bottom Terminal Block

Connect GREEN Wire from Side Tubes with GREEN Wire

from Gear Tray Assembly

GREEN GREEN

Wires going to the rest of the Gear Tray Assembly

Connect BLACK Wire from Side Tubes with BLACK Wirefrom Gear Tray Assembly

5

6

(Phillips Head)

of 5 (Rev. 07/14)

SACL_INST_v3.3








NOTICE


1. Disconnect power.2. Loosen tamper-resistant screws using spanner head screwdriver.3. Lift cap off fixture and disconnect red, black, and green wire

connections.4. Loosen (9) MS pan head screws holding light engine to cap (do not

remove screws).5. Remove light engine assembly by using keyhole design.6. Replace with new light engine, tighten screws and connect red, black

and green wires according to wiring shown on page. Ensure gasket is clean and damage-free.

7. Replace top cap making sure not to pinch wires and tighten tamper-resistant screws.

8. Reconnect to power and test luminaire.

Light Engine Maintenance

Tools Required (not included) #14 Spanner Head Driver Bit Phillips Head Screwdriver

3

2


4

5

BLACK


Cap with Attached Light

EngineBLACK

REDWHITE

GREENGREEN

Wire Connectors

Wire connection detail for #3 and #6

of 5 (Rev. 07/14)

SACL_INST_v3.3








NOTICE

Saturn Cutoff LED and Saturn 2 Cutoff LEDWiring US: Post Top

Standard Single Wiring & Dynadim (DMY)

0-10V Dimming Option (DM) Wiring LG3700 and LG3105, 120-277V.

347/480 V

Hi-Lo Switching Option (HL) Wiring LG3700 and LG3105, 120V, 240V, 277V. When red is energized, light output will be at “Lo” level.

L1

N

BLACK

WHITE

GREEN

Dim(+)

RED

ORANGEDim(-)

FROMLINECORD

SURGEPROTECTOR

LIGHTENGINE

100% LIGHT OUTPUT AT 10V, DOWN TO 10% LIGHT OUTPUT AT 0V.

0-10V DIMMING WIRING FOR 120-270V

L1

N

BLACK

WHITE

GREEN

FROMLINECORD

SURGEPROTECTOR

AUTOTRANSFORMER

LIGHTENGINE

STANDARD WIRING FOR 347/4800V WITH NO ADDITIONAL OPTIONS

STANDARD WIRING FOR 347/480V

L1

N

BLACK

WHITE

GREEN

FROMLINECORD

SURGEPROTECTOR

LIGHTENGINE

L1

N

BLACK

WHITE

GREEN

RED

FROMLINECORD

SURGEPROTECTOR

LIGHTENGINE

L2RELAY

120/240/277V. WHEN RED IS ENERGIZED, LIGHT OUTPUT WILL BE AT "LO" LEVEL.SPECIFY THE "LO" OUTPUT LEVEL BY SELECTING FROM THE TABLE BELOW.

FOR OTHER PERCENTAGE OUTPUT LEVELS, CONSULT FACTORY.

HI-LO SWITCHING OPTION (HLxx) WIRING

of 5 (Rev. 07/14)

SACL_INST_v3.3








NOTICE


1. Disconnect power.2. Loosen tamper-resistant screws using spanner head screwdriver.3. Lift cap off fixture and disconnect red, black, and green wire

connections.4. Remove (2) hex nuts and flat washers, and (2) pan head screws

holding shade in place.5. Remove and replace shade.6. Reinstall (2) hex nuts and flat washers, and (2) pan head screws to

secure the shade.7. Reconnect red, black, and green wires according to wiring shown on

page. Ensure gasket is clean and damage-free. 8. Replace top cap making sure not to pinch wires and tighten

tamper-resistant screws.9. Reconnect to power and test luminaire.

Shade Replacement

Tools Required (not included) #14 Spanner Head Driver Bit Phillips Head Screwdriver 13mm Wrench

3

2


4

5

BLACK


Cap with Attached Light

EngineBLACK

REDWHITE

GREENGREEN

Wire Connectors

Wire connection detail for #3 and #7

saturn cutoff led and saturn 2 cutoff led installation · pdf file ·...

Documents