*829696-00*829696-00

© Allegion 2018Printed in U.S.A.

829696-00 Rev. 05/18-g

A. Cover with Emergency Release Button

B. Cover Screws

C. PL7/8 Mounting Screws

D. Pull Assembly

E. Latch

F. Latch/Deadbolt/Strike Screws

G. Strike

H. Strike Box

J. Push Assembly

K. PL7/8 Mounting Nuts

L. Cover with Thumbturn

M. Lead Washers (Optional)

N. Lead Latch Cover (Optional)

CB

A

D

E

F

HG

J

K

L

Tools for Install

OR

F

N

M

Tools for Preparation

Privacy Latch

PL7/PL8Installation Instructions

Customer Service1-877-671-7011 us.allegion.com

1 Install Privacy Latch1a Use the templates from the back page to check the

holes. L NOTE: If the door holes do not match the template, see the

Door Preparation section on the back page.

Template #1

Template #2

1b For the lead lined model ONLY, install the lead lining.

Push handle Pull handle

Actuator PinCam

CamActuator Pin

Push Pull

PL7 has Thumbturn on Push SidePL8 has Thumbturn on Pull Side

ThumbturnEmergencyReleaseButton

Push

PullLead Washers (2)

Push

Pull

Lead Wrap

Template #1

Template #2 or #3

Standard Strike ASA Strike

OR

1c Install the latch.

1d Position the cams, as shown.

Push handle Pull handle

Actuator PinCam

CamActuator Pin

Push Pull

PL7 has Thumbturn on Push SidePL8 has Thumbturn on Pull Side

ThumbturnEmergencyReleaseButton

Push

PullLead Washers (2)

Push

Pull

Lead Wrap

Template #1

Template #2 or #3

Standard Strike ASA Strike

OR

1e Install the push lever and pull lever. L NOTE: The T turn side must be unlocked!

Push

Pull

1f Place the covers over the levers. Install and tighten the cover screws.

Push handle Pull handle

Actuator PinCam

CamActuator Pin

Push Pull

PL7 has Thumbturn on Push SidePL8 has Thumbturn on Pull Side

ThumbturnEmergencyReleaseButton

Push

PullLead Washers (2)

Push

Pull

Lead Wrap

Template #1

Template #2 or #3

Standard Strike ASA Strike

OR

1g Install the strike. L NOTE: If the frame is not prepared, see the Frame

Preparation section below.

Standard StrikeASA Strike

OR

OR

Standard StrikeASA Strike

OR

2 Frame Preparation2a Use the strike as a pattern to mark the frame.

Standardstrike

ASA strike

ORLatch

Door

Standardstrike

ASA strike

ORLatch

Door

OR

Standardstrike

ASA strike

ORLatch

Door

2b Drill holes.

1¹⁄₄"(32 mm)

1"(25 mm)

¹⁄₂" Deep(13 mm)

Standardstrike

ASA strike

OR

Door

Latch

Standard

Wood - #32 Pilot DrillMetal - #29 Drill, #8-32 Tap

ASA StrikeWood - ¹⁄₈" (3mm) Pilot DrillMetal - #16 Drill, #12-24 Tap

2c Mortise for strike. L NOTE: The strike should be flush to the frame.

1¹⁄₄"(32 mm)

1"(25 mm)

¹⁄₂" Deep(13 mm)

1¹⁄₄"(32 mm)

1"(25 mm)

¹⁄₂" Deep(13 mm)

3 Door Preparation3a Mark the center lines (CL

₈⁄ ⁵1

" m

m 1

4()

Mortise to ⁵⁄₃₂" (4 mm) depth

Door Edge

¹⁄₈"(3 mm)

CL

CL

Latch

1¹⁄₈"(29 mm)

1" (25 mm)Hole

2¹⁄₈"

(54 mm)

Hole

1" (25 m

m)

HoleTemplate #1Push/Pull

Latch

3³⁄₈" (86 mm)

CL

CL

₈⁄ ⁵1

" m

m 1

4()

Mortise to ⁵⁄₃₂" (4 mm) depth

Door Edge

¹⁄₈"(3 mm)

CL

CL

Latch

1¹⁄₈"(29 mm)

1" (25 mm)Hole

2₈⁄¹"

5(4m m)

Hoel

1" (25 mm)

Hoel

Template #1

Push/Pull

Lacth

3³⁄₈" (86m m)

CL

CL

Vertical Horizontal

MinimumBackset

7” (178 mm)

OR

Backset2³⁄₄", 3 ³⁄₄", 5", or 7"

(70, 95, 127, or 178 mm)

CL

CL

CL

45" (114.3 cm)From Finished Floor

Recommended

).

CL

CL

CL

45" (114.3 cm)From Finished Floor

Recommended

Backset2³⁄₄", 3 ³⁄₄", 5", or 7"(70, 95, 127, or 178 mm)

3b Mark the door.

₈⁄ ⁵1

" m

m 1

4()

Mortise to ⁵⁄₃₂" (4 mm) depth

Door Edge

¹⁄₈"(3 mm)

CL

CL

Latch

1¹⁄₈"(29 mm)

1" (25 mm)Hole

2¹⁄₈"

(54 mm)

Hole

1" (25 m

m)

HoleTemplate #1Push/Pull

Latch

3³⁄₈" (86 mm)

CL

CL

₈⁄ ⁵1

" m

m 1

4()

Mortise to ⁵⁄₃₂" (4 mm) depth

Door Edge

¹⁄₈"(3 mm)

CL

CL

Latch

1¹⁄₈"(29 mm)

1" (25 mm)Hole

2₈⁄¹"

5(4m m)

Hoel

1" (25 mm)

Hoel

Template #1

Push/Pull

Lacth

3³⁄₈" (86m m)

CL

CL

HorizontalVertical

MinimumBackset

7” (178 mm)

OR

₈⁄ ⁵1

" m

m 1

4()

Mortise to ⁵⁄₃₂" (4 mm) depth

Door Edge

¹⁄₈"(3 mm)

CL

CL

Latch

1¹⁄₈"(29 mm)

1" (25 mm)Hole

2¹⁄₈"

(54 mm)

Hole

1" (25 m

m)

HoleTemplate #1Push/Pull

Latch

3³⁄₈" (86 mm)

CL

CL

₈⁄ ⁵1

" m

m 1

4()

Mortise to ⁵⁄₃₂" (4 mm) depth

Door Edge

¹⁄₈"(3 mm)

CL

CL

Latch

1¹⁄₈"(29 mm)

1" (25 mm)Hole

2₈⁄¹"

5(4m m)

Hoel

1" (25 mm)

Hoel

Template #1

Push/Pull

Lacth

3³⁄₈" (86m m)

CL

CL

HorizontalVertical

MinimumBackset

7” (178 mm)

3c Drill holes.

3d Mortise for latch.

2¹⁄₈" (54 mm)

Hole

1" (25 mm)Hole

Template #1 CL

CL

1³⁄₄" (44 mm)

3³⁄₈" (86 mm)

⁵⁄₁₆" (8 mm)4 places

₈⁄⁵1

)m

m 14( "

Mortise to ⁵⁄₃₂" (4 mm) depth

Door Edge

2¹⁄₄"

(57

mm

)

CL

CLLatch

1¹⁄₈"(29 mm)

mm 92( "1¹⁄₈ )eloH

Template #2(standard latch)

Wood - #32 Pilot DrillMetal - #29 Drill, #8-32 Tap

1¹¹⁄₁₆" (43 mm)

1³⁄₈" (35 mm)

Additional Notes: Revision History Revision Description:g > Revised artwork

1. None B C D E F g

N/A N/A N/A N/A 075349 XXXXX

MaterialWhite Paper

Edited By Approved By EC Number Release Date

D. Toppins M. Sasso xxxxxx 05-09-18

Notes1. printed two sides2. printed black3. tolerance ± .134. printed in country may vary5. drawings not to scale

Title

INSTALLATION INSTRUCTIONS PL7/PL8 LATCHCreation DateN/A

Number

829696-00Revision

gCreated ByN/A

Activity3899 Hancock Expwy

Security, CO 80911 © Allegion 2018Software: InDesign CS6

8.50017.000

11.00011.000

FINAL SIZEBEgINNINg SHEET

FRONTFRONT