schwing gen iii smart drum - mixer & plant parts mfg. mixer system gen iii (parts/operations...
TRANSCRIPT
Schwing Mixer System Gen III
(Parts/Operations Manual)
SMART DRUM
Version 1.0
Table of Contents
GEN III SYSTEM PARTS .........................................................................................................................1 REMOTE SYSTEM
BOM (Booster) .........................................................................................................................................1
(Conventional).................................................................................................................................3
Hardware and Controls ............................................................................................................................4
Harnesses and Sensors...........................................................................................................................5
Hydraulics ................................................................................................................................................6
Miscellaneous ..........................................................................................................................................7
TRANSFER PARTS (GEN II TO GEN III) ..............................................................................................7
Contact Information:
Mixer & Plant Parts PO Box 12219
Rock Hill, SC 29731 Bus: (803) 233-7913 Fax: (586) 601-1904 readymixparts.com
1
GEN III SMART SYSTEM-BOOSTER Description
Quantity
Units
Part Number
PUMP - HYD, CLOCKWISE HYDROSTATIC (EP) 1 EA
30386328PUMP - HYD, BOOSTER AXLE CLOCKWISE ROT 1 EA 30389205VALVE - HYD, BLOCK VBL-CLC-01 1 EA 10194869VALVE - HYD, BLOCK VBL-BCP-01-230 1 EA 10194886VALVE - HYDRAULIC PRESSURE CONTROL (Q2G0 1 EA 10200209ENCLOSURE - MIXER, CAB, GEN III 1 EA 30380835RADIO - TRANS, MIXER GEN III 1 EA 30380836ENCLOSURE - MIXER D160 GEN III 2 EA 30380837ENCLOSURE - MIXER GROUND MOD GEN III 1 EA 30380838OIL, MIXER WITH 160F TEMP. SWITCH AND RE 1 EA 30386360ANGLE - BRACKET, CABLE MOUNT, DRUM CONTR 1 EA 30356823PROTECTION - VEC, MIXER, GEN III 1 EA 30380822PLT - MOUNT OMNEX CONTROL 2 EA 30386545MOTOR - HYDRAULIC,MODEL 4633-135,W/ QUAD 1 EA 30386500ENCL - CABINET, 400 X 200 X 80 1 EA 30386883OPER - SENSOR, PROXIMITY W/6" CABLE 3 EA 30350926LED - INDICATOR LIGHT STRIP 1 EA 30386786HRNSS - MIXER, VEC, REMOTE GEN III 1 EA 30380810HARNESS - MIXER MAIN GEN III 1 EA 30380809HARNESS - ICC MIXER STAND, CPL 1 EA 30380811
WMT - MOUNT POST IN CB OMNEX 1 EA
30386547
BOOSTER LIGHTING TRUCK MIXER 1 EA
30389128PROTECTION - FUSE, 5A/32V, MINI 1 EA 30369488KIT - FLANGE 1" CODE 61 5151HK-16 2 EA 30307799FITTING - HYD, ELBOW 45 DEG 1" 61 FLANGE 1 EA 30389371FITTING - HYD, ELBOW 37 DEG MALE 3/4" 1 EA 30389166FITTING - HYD, ELB 90 DEG 1" FLANGE 61 1 EA 30389370FITTING - HYD, ELB 90 #16 SWIVEL X FLARE 1 EA 30389486FITTING - HYD, #16 ORB TO #16 FLARE 1 EA 30389365FITTING - HYD, ELBOW #16 ORB X #16 FLARE 1 EA 30389357FITTING - HYD, ELBOW #16 ORB X #16 FLARE 1 EA 30389357FITTING - HYD, ELBOW #16ORB X #12 FLARE 1 EA 30389358FITTING - HYD, MALE #8 SAE X #10 1 EA 30389213FITTING - HYD, ELBOW 37 DEG MALE 3/4" 2 EA 30389166
FITTING - HYD, MALE 3/8" X 1/2" 37 DEG 2 EA 30389170
FITTING - HYD, ELBOW #10 ORB X #8 FLARE 1 EA 30389390
FITTING - HYD, MALE #12 SAE 2 EA 30389210
FITTING - HYD, TEST PLUG SAE#4 1 EA 30335096
FITTING - HYD, UNION 3/4" SAE 2 EA 30389162
FITTING- HYD, 12 ORB TO #8 FLARE 2 EA 30389465
FITTING - HYD, ELBOW 37 DEG 3/8" 2 EA 30389160
FITTING - HYD, ELB 90 #6 SWIVEL X FLARE 1 EA 30389374
FITTING - HYD, #4 ORB TO #6 FLARE 1 EA 30389466
continued on next page……………..
2
Description Quantity Units Part Number
FITTING - HYD, ELB 37 DEG MALE 1/4" 1 EA 30389169
FITTING - HYD, MALE #8 SAE X #6 1 EA 30389434
FITTING - ELBOW LNG #8ORB TO #8 FLARE 1 EA 30386265
FITTING - HYD, #4 ORB TO #4 FLARE 1 EA 30389463
FITTING - HYD, ELBOW #6 ORB X #8 FLARE 1 EA 30389435
CARTRIDGE SUN CKCB-XCN 1 EA 30391007
ENCL - TERMINAL BOX, 7-TERMINAL MIDLAND 1 EA 30346562
ANNC - ALARM BACK-UP 12V 1 EA 30337019
HARNESS - BACKUP ALARM, MIXER, (Q3G06) 1 EA 30359462
CARTRIDGE SUN CKCB-XCN 1 EA 30391007
REFLECTOR - DECK EDGE BLACK (Q7C13) 1 FT 30302690
3
GEN III SMART SYSTEM-CONVENTIONAL Description
Quantity
Units
Part Number
PUMP - HYD, CLOCKWISE HYDROSTATIC (EP) 1 EA
30386328
VALVE - HYD, BLOCK VBL-CC-01 1 EA 10194874
ENCLOSURE - MIXER, CAB, GEN III 1 EA 30380835
RADIO - TRANS, MIXER GEN III 1 EA 30380836
ENCLOSURE - MIXER D160 GEN III 2 EA 30380837
ENCLOSURE - MIXER GROUND MOD GEN III 1 EA 30380838
OIL, MIXER WITH 160F TEMP. SWITCH AND RE 1 EA 30386360
ANGLE - BRACKET, CABLE MOUNT, DRUM CONTR 1 EA 30356823
PROTECTION - VEC, MIXER, GEN III 1 EA 30380822
PLT - MOUNT OMNEX CONTROL 2 EA 30386545
MOTOR - HYDRAULIC,MODEL 4633-135,W/ QUAD 1 EA 30386500
ENCL - CABINET, 400 X 200 X 80 1 EA 30386883
OPER - SENSOR, PROXIMITY W/6" CABLE 2 EA 30350926
LED - INDICATOR LIGHT STRIP 1 EA 30386786
HRNSS - MIXER, VEC, REMOTE GEN III 1 EA 30380810
HARNESS - MIXER MAIN GEN III 1 EA 30380809
HARNESS - ICC MIXER STAND, CPL 1 EA 30380811
WMT - MOUNT POST IN CB OMNEX 1 EA
30386547
PROTECTION - FUSE, 5A/32V, MINI 1 EA
30369488
FITTING - HYD, TEST PLUG SAE#4 1 EA 30335096
KIT - FLANGE 1" CODE 61 5151HK-16 2 EA 30307799
FITTING - HYD, ELBOW 45 DEG 1" 61 FLANGE 1 EA 30389371
FITTING - HYD, ELBOW 37 DEG MALE 3/4" 1 EA 30389166
FITTING - HYD, ELB 90 DEG 1" FLANGE 61 1 EA 30389370
FITTING - HYD, ELB 90 #16 SWIVEL X FLARE 1 EA 30389486
FITTING - HYD, #16 ORB TO #16 FLARE 1 EA 30389365
PUMP - HYD, GEAR CHUTE CLOCKWISE ROTAT 1 EA 30389206
FITTING - HYD, ELBOW #16 ORB X #16 FLARE 1 EA 30389357
FITTING - HYD, ELBOW #16ORB X #12 FLARE 1 EA 30389358
O-RING - 79 X 2 1 EA 10042863
FITTING - HYD, ELBOW #8 ORB X #8 FLARE 1 EA 30389462
FITTING - HYD, ELB 90 #8 SWIVEL X FLARE 2 EA 30389436
FITTING - HYD, MALE #8 SAE X #10 1 EA 30389213
FITTING - HYD, #6 ORB TO #6 FLARE 2 EA 30389362
FITTING - HYD, MALE #12 SAE 2 EA 30389210
KIT - FLANGE 1" CODE 61 5151HK-16 2 EA 30307799
ENCL - TERMINAL BOX, 7-TERMINAL MIDLAND 1 EA 30346562
FITTING - HYD, ELB 90 DEG 1" FLANGE 61 2 EA 30389370
ANNC - ALARM BACK-UP 12V 1 EA 30337019
FITTING - HYD, MALE #12 SAE 1 EA 30389210
FITTING - HYD, ELB 37 MALE 1/4" X 3/8" 1 EA 30389167
HARNESS - BACKUP ALARM, MIXER, (Q3G06) 1 EA 30359462
CARTRIDGE SUN CKCB-XCN 1 EA 30391007
REFLECTOR - DECK EDGE BLACK (Q7C13) 1 FT 30302690
4
HARDWARE AND CONTROLS
Description
ENCLOSURE - MIXER D160 GEN III
Quantity
2
Units
EA
Part Number
30380837
ENCLOSURE - MIXER GROUND MOD GEN III 1 EA 30380838
ENCLOSURE - MIXER, CAB, GEN III 1 EA 30380835RADIO - TRANS, MIXER GEN III 1 EA 30380836
ENCL - CABINET, 400 X 200 X 80 1 EA 30386883LED - INDICATOR LIGHT STRIP 1 EA 30386786WMT - MOUNT POST IN CB OMNEX 1 EA 30386547PROTECTION - VEC, MIXER, GEN III 1 EA 30380822
ENCL - TERMINAL BOX, 7-TERMINAL MIDLAND 1 EA 30346562
MOUNTED UNDER CAB
PROTECTION-VEC, MIXER, GEN III 30380822
MOUNTED IN CAB
LED-INDICATOR LIGHT STRIP 30386786
ENCLOSURE-MIXER, CAB, GEN III
30380836
RADIO - TRANS, MIXER GEN III
30380836
WMT-MOUNT POST IN CAB
30386547
5
MOUNTED ON OR NEAR FRONT PEDESTAL
Mounted inside cabinet (30386883)
Encl - Cabinet, 400 X 200 X 80
30386883
D160 Expansion 30386883
Ground Junction 30380838
HARNESSES AND SENSORS Description
Quantity
Units
Part Number
HRNSS - MIXER, VEC, REMOTE GEN III 1 EA
30380810HARNESS - MIXER MAIN GEN III 1 EA 30380809HARNESS - ICC MIXER STAND, CPL 1 EA 30380811HARNESS - BACKUP ALARM, MIXER, (Q3G06) 1 EA 30359462OPER - SENSOR, PROXIMITY W/6" CABLE 3 EA 30350926ANGLE - BRACKET, CABLE MOUNT, DRUM CONTR 1 EA 30356823
MOUNTED NEAR DRIVESHAFT
OPER-SENSOR, PROX. W/ 6” CABLE 30350926
SENSOR BRACKET FOR DRIVESHAFT AS SHOWN, 30386891
(Part will vary per truck, refer to individual truck BOM for part number)
OPER-SENSOR, PROX. W/ 6” CABLE 30350926
ANGLE-BRKT, DRUM CONTR 30356823
6
HYDRAULICS
Description Quantity Units Part Number
PUMP - HYD, CLOCKWISE HYDROSTATIC (EP) 1 EA 30386328PUMP - HYD, BOOSTER AXLE CLOCKWISE ROT 1 EA 30389205VALVE - HYD, BLOCK VBL-CLC-01 1 EA 10194869VALVE - HYD, BLOCK VBL-BCP-01-230 1 EA 10194886VALVE - HYDRAULIC PRESSURE CONTROL (Q2G0 1 EA 10200209
OIL, MIXER WITH 160F TEMP. SWITCH AND RE 1 EA 30386360
MOTOR - HYDRAULIC,MODEL 4633-135,W/ QUAD 1 EA 30386500
Hydraulic fittings are particular to Booster and Conventional, refer to BOM section for correct parts
PUMP-HYD, BOOSTER CW 30389205
PUMP-HYD, CW HYDROSTATIC (EP) 30386328
OPER-QUAD. SPEED SENSOR 30386642
MOTOR-HYDRAULIC W/ QUAD
30386500
7
MISCELLANEOUS
Description BOOSTER LIGHTING TRUCK MIXER
Quantity
1
Units
EA
Part Number
30389128PROTECTION - FUSE, 5A/32V, MINI 1 EA 30369488
CARTRIDGE SUN CKCB-XCN 1 EA 30391007ANNC - ALARM BACK-UP 12V 1 EA 30337019
CARTRIDGE SUN CKCB-XCN 1 EA 30391007REFLECTOR - DECK EDGE BLACK (Q7C13) 1 FT 30302690
TRANSFER PARTS (GEN II TO GEN III)
Description Quantity Units Part Number
PUMP - HYD, CLOCKWISE HYDROSTATIC (EP) 1 EA 30386328PUMP - HYD, BOOSTER AXLE CLOCKWISE ROT 1 EA 30389205VALVE - HYD, BLOCK VBL-CLC-01 1 EA 10194869VALVE - HYD, BLOCK VBL-BCP-01-230 1 EA 10194886VALVE - HYDRAULIC PRESSURE CONTROL (Q2G0 1 EA 10200209OIL, MIXER WITH 160F TEMP. SWITCH AND RE 1 EA 30386360MOTOR - HYDRAULIC,MODEL 4633-135,W/ QUAD 1 EA 30386500OPER - SENSOR, PROXIMITY W/6" CABLE 1 EA 30350926KIT - FLANGE 1" CODE 61 5151HK-16 4 EA 30307799FITTING - HYD, #16 ORB TO #16 FLARE 1 EA 30389365FITTING - HYD, ELB 90 #16 SWIVEL X FLARE 1 EA 30389486FITTING - HYD, MALE 3/8" X 1/2" 37 DEG 2 EA 30389170FITTING - HYD, ELBOW #10 ORB X #8 FLARE 1 EA 30389390FITTING - HYD, ELBOW 37 DEG MALE 3/4" 1 EA 30389166FITTING - HYD, ELBOW #16ORB X #12 FLARE 1 EA 30389358FITTING - HYD, ELBOW #16 ORB X #16 FLARE 1 EA 30389357FITTING - HYD, ELBOW 37 DEG MALE 3/4" 1 EA 30389166
DMAN-3186-01 (Rev 1.0) www.omnexcontrols.com call toll free: 1-800-663-8806
Schwing Mixer System Gen III
Installation / Configuration Manual
Transmitter
Control Panel
I/O Module
March 27, 2007
Version 4
DMAN - 3186 - 01
PO Box 12219 Rock Hill SC • 29731
Ph# (803) 233-7913 • Fax# (586) 601-1904
Toll Free 1-877-327-2116
DMAN-3186-01 (Rev 1.0) www.omnexcontrols.com call toll free: 1-800-663-8806
2
www.mixerandplantparts.com3
call: 1-803-233-7913
Table of Contents
Safety Precautions ....................................................................................................................................... 4
System Overview ........................................................................................................................................ 5
Features ....................................................................................................................................................... 5
T151 Dimensions and Controls .................................................................................................................... 5
Control Panel Dimensions and Controls ...................................................................................................... 6
Special Functions......................................................................................................................................... 9
Installation Considerations ........................................................................................................................... 9
Battery Installation and Charging ................................................................................................................. 9
Power the Transmitter .................................................................................................................................. 11
Test the Transmitter / Control panel Link ..................................................................................................... 12
Download ID Code ....................................................................................................................................... 13
Drum Control ................................................................................................................................................ 13
Operating the Control Panel Menu............................................................................................................... 14
LCD Contrast Adjustment ............................................................................................................................ 14
Diagnostics—T151 Transmitter.................................................................................................................... 15
Alarms—Control Panel................................................................................................................................. 16
Diagnostics—Control Panel ......................................................................................................................... 17
Diagnostics—D160 Receiver ....................................................................................................................... 18
Troubleshooting Guide ................................................................................................................................. 19
Parts & Accessories ..................................................................................................................................... 23
Specifications ............................................................................................................................................... 23
Warranty Information.................................................................................................................................... 23
www.mixerandplantparts.com4
call: 1-803-233-7913
Safety Precautions
NOTE: These instructions are intended only for installing and operating the remote control equipment described here. This is not a complete Operator’s Manual for the Mixer Truck. For complete operating instructions of the Mixer Truck, please read the Operator’s Manual appropriate for your particular model.
READ ALL INSTRUCTIONS
CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Failure to follow the SAFETY PRECAUTIONS may result in radio equipment failure and serious personal injury Installation
PROVIDE A SAFETY CUTOFF SWITCH. If maintenance is required, the radio must be disconnected from power
USE PROPER WIRING. Loose or frayed wires can cause system failure, intermittent operation, machine damage, etc.
DO NOT INSTALL IN HOT AREAS. This apparatus can be damaged by heat in excess of 158° F (70° C)
Personal Safety
MAKE SURE MACHINERY AND SURROUNDING AREA IS CLEAR BEFORE OPERATING. Do not activate the re- mote system unless it is safe to do so.
TURN OFF THE RECEIVER POWER BEFORE WORKING ON MACHINERY. Always disconnect the remote system before doing any maintenance to prevent accidental operation of the machine
Care
KEEP DRY. Do not clean the transmitter / receiver under high pressure. If water or other liquids get inside the transmit- ter battery or control panel compartment, immediately dry the unit. Remove the case and let the unit air dry
CLEAN THE UNIT AFTER OPERATION. Remove any mud, dirt, concrete, etc. from the unit to prevent clogging of but- tons, switches, etc. by using a damp cloth.
Maintenance / Welding
DISCONNECT THE RADIO CONTROL PANEL AND I/O MODULES BEFORE WELDING on the machine the modules are connected to. Failure to disconnect will result in the destruction of the radio control panel and/or modules.
www.mixerandplantparts.com5
call: 1-803-233-7913
System Overview
The Schwing Mixer System is a portable, long range, programmable radio remote control system. Designed as a compact and easy-to-use product, this system puts complete control of your mixer where it’s needed most, with the operator. It’s robust, easy to install and has complete self-diagnostics. The system consists of a portable transmitter, a Contactless Charging control panel, two I/O modules and a ground junction.
The Schwing Mixer System uses Frequency Hopping Spread Spectrum (FHSS) technology. FHSS devices concen- trate their full power into a very narrow signal that randomly hops from frequency to frequency within a designated band. This transmission pattern, along with CRC-16 error-checking techniques, enables signals to overcome interfer- ence that commonly affects licensed radios.
The Control Panel and Modules are designed to be powered from a 12VDC or 24VDC system. Each module fea- tures up to 19 solid state, high-side driver input / output controls and a reliable E-Stop control.
The T151 transmitter comes with 14 digital controls. A unique ID code is used by each T151 to ensure that no two systems will conflict on a job site.
Features • FCC, ISC, CE approved
• License free
• Hand held / weatherproof / ergonomic
• Contactless Battery Charging
• Auto Battery Type Detect
• Transmitter Missing Detection
• 1200 foot range @ 900 MHz
• Simple “wire-and-use” installation
• Resilient to impact and shock
• Tether cable included
• Diagnostic Indicators
T151 Transmitter
D160 Expansion
Ground Junction
Control Panel
T151 Dimensions and Controls
4.92” 3.75”
Battery / Tether LED
Hopper UP / DOWN
Throttle UP / DOWN
Active LED
Remote ON / OFF
4.75”
Drum START / STOP
Drum CHARGE / DISCHARGE
Chute LOCK / UNLOCK
Chute UP / DOWN
www.mixerandplantparts.com6
call: 1-803-233-7913
Control Panel Dimension and Controls
5.75” Charge Status LED
Display
Constant Speed (Hold for Setup)
3.75”
7.5”
Link LED
Error LED
Status LED
RS 485 LED
STAT
RS-485
Function Select
Mode Control
1. Selecting Functions
A. Each Function Select button selects A. the column content directly above it. A highlight box will appear around the function that is currently selected.
B. Once a column is selected, press the
Function Select button a second time to move the highlight to the desired function (Except for Drum Control, see NOTE below). Each press of the button will toggle the highlighted area
B.
between the functions. Press once and CHUTE LOCK / UNLOCK is highlighted
Press again and CHUTE UP / DOWN is highlighted
NOTE: Drum Control functionality operates differently. Please refer to the Drum Control section for precise control operation directions.
2. Turning ON / OFF (Modifying) Functions
A. The Mode (Speed) Control buttons selects the top or bottom function within the highlighted group.
B. To change a setting, press the top
Mode Control button to select the top function in the highlighted box and press the bottom Mode Control button to select the bottom function in the highlighted box.
A. B.
Press to change from CHUTE UNLOCK to CHUTE LOCK
Press to change from CHUTE LOCK to CHUTE UNLOCK
www.mixerandplantparts.com9
call: 1-803-233-7913
Special Functions
Installation Considerations
NOTE: The FCC and ISC require that the antenna be restricted to that supplied by the manufacturer and approved for use with this product. An op- tional 0dB coax wire antenna may be supplied. For other antenna options, please contact OMNEX Control Systems ULC
Mounting and Installation
The I/O Module can be mounted by fastening two ¼” bolts through the two mounting holes in the unit’s enclosure. When mounting, ensure that the I/O Module is oriented so that the text is reading right and the connectors are pointing down.
When selecting a mounting point for the I/O Module, it is recommended that the location require only a minimal length of wiring to connect it to the control panel, that it will be in a visible area where it has good exposure to the operator and that it is mounted on a surface that is protected from the weather and sustains minimal vibration. It is also recommended that the control panel have the best possible line of sight with the transmitter
Power Connections and Wiring Whenever a power connection is made to an electronic device, it is a good practice to make both the Power (+) and Ground (-) connections directly to the Battery and avoid connecting the power from the charging side of existing wiring or making use of existing "ACC" or other peripheral connection points.
Make sure that wire of sufficient gauge and insulator type is used when connecting the outputs of the receiver to the con- trol panel. Observe any component manufacturer's instructions and recommendations for proper integration of their product. This includes the power ratings and requirements of such components as relays, valves, solenoids, etc.
Be sure to test each of the outputs with a multi-meter prior to connecting the outputs to your end devices. This will ensure that each output has been programmed to operate in the manner required by each end device.
Filtering and Noise Suppression
Whenever a solenoid or electromagnetic switch is controlled by the receiver, it is a good practice to install a Diode across its terminals to ensure that surges and spikes do not continue back into the circuit. Appropriate 36V Bi-directional Diodes kits can be ordered under the OMNEX part number “AKIT-2492-01”.
www.mixerandplantparts.com10
call: 1-803-233-7913
Battery Installation and Charging
When the control panel has been installed, install batteries into the transmitter.
1. Install Batteries
Remove the battery cover on the back of the transmitter using a slotted screwdriver and insert the 4 "AA" rechargeable batteries. Orientation of the batteries is embossed inside the battery housing. No batteries are required when the transmitter is connected to the control panel by a tether cable.
NOTE: For operation at temperatures below –10° C, lithium batteries are recommended. Low temperatures re- duce battery performance for both alkaline and lithium types. Refer to the battery manufacturer’s specifications for detailed information on low temperature performance.
T151 Battery
WARNING: do not install batteries backwards, charge, put in fire, or mix with other battery types. May explode or leak causing injury. Replace all batteries at the same time as a complete set and do not mix and match battery types.
2. Charge Batteries
Place the transmitter in the Charge Cradle. The cradle will detect the transmitter and start charging. The (Charge Status) light on the transmitter will slow flash YELLOW. Fully charge the batteries for 8 hours or until the (Charge Status) light on the transmitter turns solid YELLOW. The charging time may be longer in hot or cold temperature ex- tremes. The (Status) light will be solid GREEN when charging is complete.
A. Cradle detects the transmitter and the batteries are charging
B. Batteries are fully charged
A. B.
NOTE: should the batteries need charging during a job, 15 minutes of charging will pro- vide about 3-4 hours of operation, 1 hour of charging should provide approximately 12-16 hours of operation.
Tips for best performance:
1. The system was designed to work best with NiMH batteries. Regular alkaline batteries and NiCad batteries will work, however, system performance may not meet all specifications.
2. Charge the batteries at the end of every shift. Temperature extremes (freezing and hot temperatures) will diminish battery performance, therefore, keep the batteries as fully charged as possible at all times to maximize operation time.
3. Charging will not occur when vehicle is shut off.
Light Legend Solid
Slow Flash 1x / sec
Double Flash
Fast Flash Red Light
Green Light
Yellow Light
www.mixerandplantparts.com11
call: 1-803-233-7913
Power the Transmitter
1. Turn the Transmitter ON or OFF
Refer to the Light Legend below for diagram details.
A. Turn Transmitter ON B. Turn Transmitter OFF
Press [Remote] UP If the transmitter's (Active) light does not flash, check the battery orientation.
Press [Remote] DOWN
Test the Transmitter / Control panel Link
Follow these steps to ensure that there is a radio link between the transmitter and control panel. Refer to the Light Legend below for diagram details
1. Ensure the Transmitter is OFF
2. Power the Control Panel CHARGE
LINK
ERROR
STAT
RS 485
CHARGE
LINK
ERROR
STAT
RS 485
With T151 out of Cradle With T151 in Cradle
3. Power the T151 CHARGE
LINK
ERROR
STAT
RS 485
If the (Active) light on the transmitter is flashing and the (Link) light on the control panel is flashing GREEN, a link be- tween the two exists.
If the control panel’s (Link) light does not flash GREEN, follow the steps under Download ID Code.
The ORIGA system is now ready for use.
Light Legend Solid
Slow Flash 1x / sec
Double Flash
Fast Flash Red Light
Green Light
Yellow Light
www.mixerandplantparts.com12
call: 1-803-233-7913
Download ID Code (Use in case of Link Test failure)
Follow these steps to download the transmitter’s unique ID Code into the control panel. This will allow the control panel to establish a radio link with that transmitter.
Refer to the Light Legend below for diagram details. Refer to Troubleshooting Chart #4 for Tips and Considerations
NOTE: It is necessary to download the ID Code when replacing either the transmitter or the control panel.
1. Prepare the Control Panel for Download
A. Press & hold [Setup] for 4 seconds until System Control screen appears
B. Highlight “Link with Remote” using [Mode] buttons
A. CHARGE
LINK
ERROR
STAT
RS 485
DRUM SPEED 0.0RPM 0 PW M
BP 0 PSI
DRUM CHUTE THROTTLE BOOSTER
ST LK UP UP
SP UN DN DN
CH UP HOPPER LIGHTS
B.
USER SETUP
BOOSTER ENABLED: YES
DRUM TOTAL REVS: 000 RESET
LINK WITH REMOTE
DISPLAY FIRMWARE VERSION
2. Put Control Panel into Setup Mode
A. Press the [Select] button to place the
control panel into Setup Mode
A. B.
USER SETUP
BOOSTER ENABLED: YES
DRUM TOTAL REVS: 000 RESET
LINK WITH REMOTE
DOWNLOAD FIRMWARE
CHARGE
LINK
LINK W ITH REMOTE
LINK TO REMOTE
C.
CHARGE
LINK
LINK W ITH REMOTE
LINK TO REMOTE
B. The display should now indicate that the control panel is ready for the download
ERROR
STAT
RS 485
RF ID UPLOADING ... ERROR
STAT
RS 485
RF ID UPLOADING ... FAILED
NOTE: If left idle in Setup Mode for over 30 seconds, the control panel will time out. The (Link) light and (Status) light will flash RED rapidly and the display will read “RF ID UPLOADING FAILED”. To return to Setup Mode, Press [ESC] to go back to the main screen and repeat steps 1 and 3. If you do not re-enter Setup Mode, you will need to turn off then turn on the control panel to remove the flashing (LINK) and (STAT) light condition.
3. Power T151 into Configuration Mode A. B.
A. Hold [Hopper] switch UP
B. Press [Remote] switch DOWN
C. Release [Remote] switch
D. Release [Hopper] switch. The (Active) C. D. light should be flashing.
4. Download ID Code
NOTE: When downloading a new ID to a receiver, a safety feature requires that the transmitter be in close proximity to the receiver. This will pre- vent a transmitter from accidentally reprogramming a different receiver in the area.
A. Press [Hopper] switch UP and Release
B. (Link) light goes to GREEN
A. B. CHARGE
LINK
ERROR
STAT
RS 485
LINK TO REMOTE
LINK W ITH REMOTE
RF ID UPLOADING...
5. Download Complete
A. Once complete, (Link) light goes to
RED as the transmitter turns off
A.
CHARGE
LINK
LINK W ITH REMOTE
LINK TO REMOTE
B. The display will now indicate that downloading is complete
ERROR
STAT
RS 485
RF ID UPLOADING ... COMPLETE
Light Legend Solid
Slow Flash
Fast Flash
Red Light
Green Light
Yellow Light
Alternating Red & Green Light
www.mixerandplantparts.com13
call: 1-803-233-7913
Drum Control
A. Press the [Function Select] button to highlight the Drum control column
B. Pressing this button toggles the START and STOP function of the drum
A. Press the top and bottom [Mode] buttons to adjust the drum rotation speed and direction
B. Observe the PWM value in the top right corner of the screen to determine increase and decrease direction.
A.
A.
B.
B.
Note: To select DC (Discharge) or CH (Charge), you must toggle between the settings by reducing the PWM value to minimum value. Once this min. value is reached, the controller will toggle directions. Continue pressing the same button to increase the drum speed. Press the opposite button to reduce speed and once min. is reached, the controller will switch directions and now the button will increase the value.
A. From the transmitter use the Start/Stop switch to toggle the start/stop function of the drum
B. The Charge/Discharge switch works in exactly the same fashion as the [Mode] button on the Control Panel. Once the switch is toggled and the PWM speed hits minimum, the drum will switch direction and the switch will act as a speed control switch
A. B.
A. Press the [Constant Speed] button to set the drum rotation’s RPM to the default setting
Note: Constant Speed engages auto- matically when vehicle speed exceeds 15 mph.
A.
Note: You can press the [Constant Speed] button from the start position as a “quick start” function to set the system in motion.
Light Legend Solid
Slow Flash 1x / sec
Double Flash
Fast Flash Red Light
Green Light
Yellow Light
www.mixerandplantparts.com14
call: 1-803-233-7913
Operating the Control Panel Menu
To access the Control Panel menu, press and hold the [Constant Speed] button for about 4 seconds until the System Menu screen appears
Use the [Mode] buttons to move the high- lighted area up and down to select the de- sired Menu item.
Press the button under the SEL [Select] to select that menu item
Menu Item Descriptions
Booster Enable—Enables and Disables the booster axle control system
Drum Total Revs—Monitors and counts the total number of drum revolutions
Link with Remote—Used to place the Control Panel into Download ID mode.
Display Firmware Version—Display the software version currently installed in the Control Panel.
LCD Contrast—View and adjust current contrast setting
LCD Contrast Adjustment
A. To increase or decrease the LCD Con- trast, select the LCD menu item and press the [SEL] button.
B. Press the buttons under [-] or [+] to in-
crease or decrease the contrast.
Once completed press the [ESC] button to return back to the main screen
Light Legend Solid
Slow Flash 1x / sec
Double Flash
Fast Flash Red Light
Green Light
Yellow Light
www.mixerandplantparts.com15
call: 1-803-233-7913
Diagnostics—T151 Transmitter
Tether connection detected
Low battery. Unit will run approximately 10 hours after Battery light starts flashing.
Flashing rapidly for 10 seconds indicates a transmitter failure.
Normal Operation The Active light will flash several times per second, indicating that the transmitter is sending signals to the control panel. The Active light will remain on momentarily whenever a function changes
Normal Operation The transmitter is in Download Mode.
Stuck switch detected. Ensure that all switches are in a centered position. The transmitter will not power up when a function is ON.
On Power Down Unit is still powered. Check for stuck switches, as the transmitter will not power down when a function is ON. Alternating flash means that the transmitter is in Calibration Mode.
The transmitter is in the Control Panel charge cradle and the batteries are charging.
The batteries in the transmitter are fully charged.
Transmitter is in the powered cradle and attempting to charge but the temperature of the bat- teries is either above 60° C or below 0° C. Either cool or heat the batteries to bring them within charging temperature
A problem with the batteries has been detected. (No batteries, no contact to batteries, non- rechargeable batteries, backward batteries, dead batteries) This is a common error if using alkaline batteries or other non-rechargeable batteries.
Light Legend Solid
Slow Flash 1x / sec
Double Flash
Fast Flash Red Light
Green Light
Yellow Light
www.mixerandplantparts.com16
call: 1-803-233-7913
Alarms—Control Panel
Sensors located throughout the machine provide feedback to the Control Panel. When a parameter is not within accept- able operating range an alarm will sound and the appropriate warning label will appear on the Control Panel screen. The following are the list of alarms in the mixer system.
No Signal—This is indicated by a “NO SIG” symbol replacing the Drum Speed RPM indicator. The alarm is activated when the Pulse Counter input from the drum is lost.
BP—This is indicated by a blinking “BP” symbol. This alarm sounds when the Booster is being driven down and the Booster pressure has fallen by at least 500 psi.
REM—This is indicated by a “REM” symbol located next to the BP indicator. The Control Panel has indicated that the remote control is not in the Charge Cradle and the vehicle is traveling over 15 mph. This is to prevent the driver from leaving the work site and forgetting the remote control outside or on the truck.
OIL—This is indicated by a “OIL” symbol located directly under the Drum Speed RPM indicator. This alarm indicates that the oil cooler fan has turned on.
BIM—Booster in Motion is indicated by a “BIM” symbol located under the Drum Speed indicator. This alarm alerts the driver that the Booster is either up or down. This lets the driver know not to drive the truck while it is in transition between the up and down position.
CHUTE—This is indicated by a “CHUTE” symbol located under the Drum Speed indicator. This occurs when the chute is not in the center and up position. This will let you know if it is safe to move the booster up or not.
www.mixerandplantparts.com17
call: 1-803-233-7913
Diagnostics—Control Panel
Normal Operation
CHARGE
LINK
ERROR
STAT
RS 485
CHARGE
LINK
ERROR
STAT
RS 485
Transmitter is OFF The Transmitter is recognized by the Control Panel cradle and being in the cradle. Output status is correct and the E-Stop relay is open and working properly. Transmitter is ON The Transmitter is recognized by the Control Panel cradle and being in the cradle. Output status is correct and the E-Stop relay is open and working properly. Transmitter and Control Panel have a radio link.
CHARGE
LINK
ERROR
STAT
RS 485
CHARGE
LINK
ERROR
STAT
RS 485
Transmitter is OFF The Transmitter is not recognized by the Control Panel cradle as the Transmitter is not in the cradle. Output status is correct and the E-Stop relay is open and working properly. Transmitter is ON The Transmitter is not recognized by the Control Panel cradle as the Transmitter is not in the cradle. Output status is correct and the E-Stop relay is open and working properly. Transmitter and Control Panel have a radio link.
Trouble Indicators
Note: In some cases, the indicator lights will be different depending on whether the transmitter is on or off. These will be reflected in the (CHARGE) light and (LINK) light. Please note the these status lights in the Normal Operation section.
Indicator Lights
Description Solution
CHARGE
LINK
ERROR
STAT
RS 485
Transmitter - ON When the (ERROR) light activates, text will appear on the display to indicate the error type.
Read the error code to determine what the issue is. Refer to theAlarm—Control Panel on page 15 for alarm descriptions. Once determined, correct the issue or refer to Vehicle’s Operators Manual to determine the appropriate steps.
CHARGE
LINK
ERROR
STAT
RS 485
Transmitter - ON The Control Panel has lost communication with the I/O Modules.
Refer to the I/O Module diagnostic indicators to determine module status and refer to the D160 diagnostic page for a solution. If the D160 modules appear to be in working order, check the Control Panel to Module connections.
CHARGE
LINK
ERROR
STAT
RS 485
Transmitter - ON Irrecoverable internal fault.
Call for service.
CHARGE
LINK
ERROR
STAT
RS 485
Transmitter - ON The internal temperature of the cradle is above +60° C (140° F).
If possible cool down the cradle to within operating temperaturerange
CHARGE
LINK
ERROR
STAT
RS 485
Transmitter - ON No remote control unit has been linked with the Charge Cradle control panel
Download ID code of the remote control to the control panel
CHARGE
LINK
ERROR
STAT
RS 485
Transmitter - ON The voltage to the Charge Cradle is not within 9—29 VDC
Bring the power supply to within operating parameters
Light Legend Solid
Slow Flash 1x / sec
Double Flash
Fast Flash Red Light
Green Light
Yellow Light
www.mixerandplantparts.com18
call: 1-803-233-7913
Diagnostics - D160 I/O Module
Normal Operation
ESTOP FAULT LINK STATUS If the control panel is off, the module is operating properly.
ESTOP FAULT LINK STATUS
When the control panel is turned on, the Link light (fast flashing) and E-Stop (GREEN) indicates the module is operating properly.
ESTOP FAULT LINK STATUS
When a function is activated on the transmitter or the control panel, the Fault light will turn on GREEN. This indicates the module is operating properly.
ESTOP FAULT LINK STATUS
When a latched function is activated then the transmitter is turned off, the Fault light will stay on GREEN. The system was intentionally designed this way, the module is operating properly.
Trouble Indicators
Note: In some cases, the indicator lights will be different depending on whether the transmitter is on or off. Please note the transmitter status in the “Description” column for each case.
Indicator Lights Description Solution ESTOP FAULT LINK STATUS
The reason is the control panel is not communicating with the module.
Refer to Troubleshooting Chart #3 for solutions.
ESTOP FAULT LINK STATUS
A low battery condition has been de- tected.
To detect intermittent conditions caused by poor or corroded ground or power circuits, the GREEN light will continue to flash for 30 seconds after the condition has been removed.
ESTOP FAULT LINK STATUS
An internal fault with the E-Stop has been detected.
Inspect E-Stop wiring for short circuit. Disconnect E-Stop wire as close to the control panel output as possible. If the Status light changes to: • GREEN, a short occurs after disconnection point. • Stays flashing RED, send it in for service .
ESTOP FAULT LINK STATUS
A short to ground or excessive current draw on an output. It is most likely caused by a wiring fault.
Ensure transmitter is functioning properly, check status of each output connection: Press each function button and observe Fault Light. • If GREEN, everything is OK. • If RED, there is a short in that connection.
ESTOP FAULT LINK STATUS
The E-Stop output has been connected with one of the other outputs.
Follow the wire and check for connections with other wires, discon- nect to see if condition clears. If not, call for service.
A wiring short to the battery has been detected.
Refer to Troubleshooting Chart #1 for solutions.
ESTOP FAULT LINK STATUS
The module has detected an internal fault.
Refer to Troubleshooting Chart #1 for solutions.
ESTOP FAULT LINK STATUS
ESTOP FAULT LINK STATUS
Blown fuse detected.
Refer to Page 8 for instructions on how to open the I/O module case to access fuse. Check wiring for shorts or bare spots. If fuses continue to blow, call for service.
ESTOP FAULT LINK STATUS
The module is powered incorrectly. Most likely cause of this condition is that an output wire or the E-Stop wire has been connected to the power supply while the power wire is disconnected from the power supply.
Light Legend Solid
Slow Flash
Fast Flash
Red Light
Green Light
Yellow Light
Alternating Red & Green Light
www.mixerandplantparts.com19
call: 1-803-233-7913
Troubleshooting Guide Chart #1
Test the D160 I/O Module
Start Initial Condition: Turn transmitter off Cycle power to module (turn off and back on)
Problem state: Status—RED
What is the state of the lights on the module?
OK state: Status—GREEN Link—RED Fault—OFF E-Stop—RED Note: If there is a short to ground on an output, it is not indicated at this stage. To test for short to ground, refer to the “*Fault Light is RED*” procedure at the bottom of this page and follow the instructions.
Problem state: Status—flashing GREEN & RED
The system is wired incorrectly. Most likely cause is one of the in- put/output wires has been connected to the power source.
Go to Chart 2
Is the Status light flashing
RED?
YES
Fuse is blown, change fuse 1. Inspect wiring looking for short circuits (e.g. bare wires) 2. If problem re-occurs, call for service.
NO Inspect E-Stop wiring looking for short circuits (e.g. bare wires) Disconnect the E-Stop output as close to the
What is the state of the E-
Stop light ?
Problem state: E-Stop— Flashing RED
receiver output as possible. If the Status light changes to: • GREEN, there is a short is the wiring after the discon-
nection point. • Stays flashing RED, call for service .
OK state: E-Stop—RED
Fault Light is
OFF
Call for service.
What is the state of the Fault light ?
Fault Light is Flashing RED
There is a short to supply. 1. Disconnect A & B connectors from receiver and check all
outputs for power (e.g. bare wires, improper connections) make the correct adjustments
2. Call for service.
*Fault Light is
RED*
There is a short to ground. Note: This should only occur when the transmitter is on and a function button is pressed. In this case the Status light will be GREEN and will turn RED at the same time as the Fault light.
Go to Chart 2 to test the transmitter. If the transmitter is func- tioning properly, proceed to check the status of each of the out- put connections: Press each of the function buttons and observe the Fault Light. If the light turn GREEN, everything is OK. If the Light turns RED, there is a short in that connection.
www.mixerandplantparts.com20
call: 1-803-233-7913
Troubleshooting Guide (con’t) Chart #2
Test the Transmitter—T151
Turn off the control panel Ensure there are good batteries in the transmitter Turn on the transmitter
What is the state of the lights?
OK state: Active light—steady for about 3 seconds then goes to fast flash. Battery light—OFF E-Stop light—OFF
Activate a function
Go to Chart 3 YES Does the Active light go to solid
YELLOW?
No light comes on at any time
Complete the following steps in order: 1. Check battery orientation 2. Clean battery contacts 3. Check or Replace batteries 4. Call for service
NO
Either the switch is defective or the switch connection to the circuit board is broken.
Call for service
Both the Active light and the Battery light flash at the same time
Stuck switch: 1. Return all switches to neutral (OFF)
position 2. Toggle the switch a few times 3. Call for service
Active light is flashing rapidly and Battery light flashing slowly
Low Battery—Change/Charge Batteries Note: Low batteries will last approxi- mately 10 hours once the Low Battery light begins to flash. Replace /Charge batteries by next shift.
Battery light and Active light flash alternately.
The transmitter is in Calibration mode 1. Turn unit OFF, then turn back ON 2. If condition persists, call for service.
Battery light flashes for 10 seconds then all lights are OFF
Press and release E-Stop if the condition persists, then either there is a faulty E- Stop or transmitter failure—call for ser- vice
www.mixerandplantparts.com21
call: 1-803-233-7913
Troubleshooting Guide (con’t) Chart #3
Testing the Transmitter / Control Panel Communication
Transmitter: Active light is flashing
Control Panel: Status—GREEN Link—RED
What is the status of the lights of both the
transmitter and receiver?
Transmitter: Active light is flashing Control Panel: Status—GREEN Link—Flashing GREEN
There is no link between the transmitter and receiver
Transmitter and receiver should be working properly. The problem may rest with the machine instead of the radio system Call for service
Do you have a matched set? (i.e. the
transmitter and re- ceiver should have identical ID codes
YES
Call for service.
NO
Was the transmitter accidentally swapped with another one on
the job site?
POSSIBLY
Search the job site for the correct transmitter.
NO YES Was it found?
NO
Turn on the transmitter to check if the units function correctly. If not, proceed to Chart 1
The transmitter code may need to be re-downloaded to the receiver
!!Caution!! Note: Before you proceed with the Download ID procedure located on Page 12, great care and caution must be adhered to. Also, refer to Chart #4 for Tips and Considerations. If by accident, the transmitters have been switched with another unit, by downloading the ID code to a new receiver, it is possible for the transmitter to operate 2 units at the same time (if the original receiver unit is still on the job site). Therefore it must be certain that the transmitter / receiver pair are the correct set. Secondly, once the download procedure is completed, ensure all other units on the job site are stopped. Test the operation of the newly configured set to ensure no other machines on the site work with the same transmitter. Once you are certain that the transmitter / receiver pair are a unique set, continue normal operations.
www.mixerandplantparts.com22
call: 1-803-233-7913
Troubleshooting Guide Chart #4
Considerations when Downloading the ID
Potential downloading issues
If testing of the control panel and transmitter both show the system as working (Chart 2 & 3), then the transmitter and control panel will both go into Download/Configuration mode.
Possible issues could arise during Step 4, the download phase of reprogramming. In this case there are 2 symptoms to look for:
1. The Link light on the control panel will not turn GREEN when the power switch is toggled on the transmitter to download
2. The control panel will “time out” indicating that it didn’t receive a signal from the transmitter within the 30 seconds from the time the control panel was put into Setup Mode.
If all indications appear normal during the download phase, test the link by turning on the transmitter (note: the transmit- ter shuts off after transmitting the ID code in Step 4)
1. If the Link light on the control panel doesn’t turn GREEN, the control panel didn’t receive all of the information that
was sent from the transmitter.
Possible Solutions
1. Try the Downloading steps again
2. If this doesn’t correct the problem, send both the transmitter and control panel in for service.
Note: you could try to determine whether the fault lies with the transmitter or control panel by completing the downloading procedure with a different transmitter. If this step works, then the fault lies with the original transmitter. If not, the fault may lie with the control panel.
!!Caution!!
Note: Before attempting downloading with another transmitter, understand that repro- gramming the control panel with another transmitter, could result in two control panels on the job site responding to the one transmitter. If the original transmitter was sent in for repair, Disconnect the control panel (disconnect connector A) to continue using the machine without remote capability and without fear of inadvertently operating the machine with the other transmitter.
Connector A
23
DMAN-3186-01 (Rev 1.0) www.omnexcontrols.com call toll free: 1-800-663-8806
Parts & Accessories
Part Part Number Description
Batteries B0010 4 x AA alkaline
T151 Tether Cable (8 m. / 25 ft.) ACAB-2455-02 see illustration
Toggle Switch
AKIT-1504-04 Honeywell 1TL1-7
Magnet Back AKIT-2498-02 see illustration
Bipolar Diode Kit AKIT-2492-01 36V, Bi-directional, Motorols P6KE36CA
Fuse F0039 Bussman ATC-15
Socket Connectors
J0418 Grey, 12-pin, Deutsch DTM06-12SA
J0419 Black, 12-pin, Deutsch DTM06-12SB
Wedge J0420 12 pos., Deutsch WM12S
Pin J0417 Female, Size 20, Deutsch 0462-201-20141
Sealing Plug J0421 Size 20, Deutsch 0413-204-2005
D160 Connector Kit
AKIT-2337-01 Includes Deutsch socket connectors, wedges, pins and sealing plugs.
Specifications
D160 I/O Module T151 Transmitter
Size 5.1” x 4.7” x 1.4” (130mm x 119mm x 36mm)
7.9” x 4.2” x 4.1” (200mm x 125mm x 105mm)
Weight 0.65lbs (0.295kg) 1.8lbs (0.817kg)
Construction
High impact plastic, weatherproof High impact, low temperature plastic, weatherproof
Input Power +9V to 30VDC 4AA alkaline batteries or NiMH rechargeable
Battery Life N/A 160 hours (continuous use)
Operating Temperature Range
-40F to 158F (-40C to 70C) -40F to 158F (-40C to 70C)
Outputs 3A (max) each (sourcing), 10A (max) each (combined)
N/A
Antenna Internal Internal
Approvals USA- FCC part 15.247 Canada- ISC RSS 210 Issue 6, Sept. Europe- EN 440 Australia- C-Tick
FCC Rules and Compliance
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two condi- tions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause unde- sired operation.
FCC Part 15.247 ISC RSS 210 Issue 6, Sept.
2005
Warranty
OMNEX Control Systems ULC warrants to the original purchaser that the OM- NEX products are free from defects in materials and workmanship under normal use and service for a period of ONE YEAR, parts (EXCLUDING: SWITCHES, CRYSTALS, OR PARTS SUBJECT TO UNAUTHORIZED REPAIR OR MODIFI- CATION) and labor from the date of delivery as evidenced by a copy of the receipt. OMNEX's entire liability and your exclusive remedy shall be, at OM- NEX's option, either the (a) repair or (b) replacement of the OMNEX product which is returned within the warranty period to OMNEX freight collect by the OMNEX APPROVED carrier with a copy of the purchase receipt and with the return authorization of OMNEX. If failure has resulted from accident, abuse or misapplication, OMNEX shall have no responsibility to repair or replace the product under warranty. In no event shall OMNEX be responsible for incidental or consequential damage caused by defects in its products, whether such dam- age occurs or is discovered before or after replacement or repair and whether or not such damage is caused by the negligence of OMNEX Control Systems ULC.
MPPM PO Box 12219 Rock Hill, SC 29731 Tel: 803-233-7913 Fax: 586-601-1904 Visit us online: www.readymixparts.com
Contact Information: Mixer & Plant Parts
PO Box 12219 Bus: (803) 233-7913 Fax: (586) 601-1904 readymixparts.com