sctx woodworkers club
DESCRIPTION
SCTX WOODWORKERS CLUB. POWER EQUIPMENT USAGE MANUAL. SEPTEMBER 2008. ACCESS VIA THE WEBSITE. http://www.sctxwoodshop.com/. CLICK ON “ Woodshop Information ”. ACCESS VIA THE WEBSITE. http://www.sctxwoodshop.com/. CLICK ON “ POWER EQUIPMENT USAGE MANUAL ” LINK. ACCESS VIA THE WEBSITE. - PowerPoint PPT PresentationTRANSCRIPT
SCTX SCTX WOODWORKERS WOODWORKERS
CLUBCLUBPOWER EQUIPMENT POWER EQUIPMENT
USAGE MANUALUSAGE MANUAL
SEPTEMBER 2008
2
ACCESS VIA THE ACCESS VIA THE WEBSITEWEBSITE
CLICK ON “Woodshop Information”
http://www.sctxwoodshop.com/
3
ACCESS VIA THE ACCESS VIA THE WEBSITEWEBSITEhttp://www.sctxwoodshop.com/
CLICK ON“POWER
EQUIPMENT USAGE MANUAL”
LINK
4
ACCESS VIA THE ACCESS VIA THE WEBSITEWEBSITE
• You will have to have Adobe You will have to have Adobe Reader 8 or higher.Reader 8 or higher.
• Be patient – the file will take Be patient – the file will take from 30 seconds to 2 minutes from 30 seconds to 2 minutes or more to open.or more to open.
http://www.sctxwoodshop.com/
5
ACCESS VIA THE ACCESS VIA THE WEBSITEWEBSITEhttp://www.sctxwoodshop.com/
CLICK ON“BOOKMARK”
ICON
6
ACCESS VIA THE ACCESS VIA THE WEBSITEWEBSITEhttp://www.sctxwoodshop.com/
7
ACCESS VIA THE ACCESS VIA THE WEBSITEWEBSITEhttp://www.sctxwoodshop.com/
SCROLL DOWN TODESIRED SECTION
8
ACCESS VIA THE ACCESS VIA THE WEBSITEWEBSITEhttp://www.sctxwoodshop.com/
HIGHLIGHT SECTION
WITH LEFT CLICK
9
ACCESS VIA THE ACCESS VIA THE WEBSITEWEBSITEhttp://www.sctxwoodshop.com/
RIGHT CLICK AND
HIGHLIGHT “Print Page(s)”
TO PRINT SELECTED SECTION
10
ORGANIZATION OF ORGANIZATION OF MANUALMANUAL
Section 1:Section 1: Introduction Introduction Section 2:Section 2: General safety rules General safety rules Section 3:Section 3: Additional resources Additional resources
•in the Woodshop and in the Woodshop and •externalexternal
Section 4:Section 4: How to prepare a board How to prepare a boardSections 5 - 30:Sections 5 - 30: Major pieces of Major pieces of equipmentequipment
Section 31:Section 31: Procedures and rules Procedures and rules on Glue-upson Glue-ups
11
TYPICAL INFORMATIONTYPICAL INFORMATION7. SAW, TABLE (10” POWERMATIC 66-TA, DELTA 36-L53L, DELTA 34-806) ...................................................... 21
7.1. SAFETY PRECAUTIONS ............................................................................................................................... 21 7.2. SETUP – TABLE SAW ................................................................................................................................. 23
7.2.1. Changing the Blade ..................................................................................................................... 23 7.2.2. Blade Raising and Tilting ............................................................................................................. 23 7.2.3. Installing Splitter Guard Assembly .............................................................................................. 24 7.2.4. Miter Gauge Adjustment............................................................................................................. 24 7.2.5. Conditions Which Can Cause Kickbacks ....................................................................................... 24
7.3. SAFETY DEVICES ....................................................................................................................................... 25 7.4. FEED RATE .............................................................................................................................................. 26 7.5. RIP CUTS ................................................................................................................................................ 27 7.6. CROSSCUTS & MITER CUTS ........................................................................................................................ 28
7.6.1. Large Miter Gauge for the Powermatic Saw ............................................................................... 29 7.6.2. Making a Crosscut or Miter Cut ................................................................................................... 30
7.7. BEVEL & COMPOUND ANGLE CUTS .............................................................................................................. 30 7.7.1. Bevel crosscutting ....................................................................................................................... 31 7.7.2. Compound Mitering .................................................................................................................... 31 7.7.3. Bevel Ripping .............................................................................................................................. 31
7.8. DADOS & RABBETS .................................................................................................................................. 31
12
REVISIONSREVISIONS
• Revisions, edits, Revisions, edits, suggestions, etc. are invitedsuggestions, etc. are invited
• Contact Contact [email protected]@suddenlink.netenlink.net – Be specific in your emailBe specific in your email– Include name and phone Include name and phone
numbernumber