section -10 cover page - hpcltenders.hpcl.co.in/tenders/tender_prog/tenderfiles/3460/notice... ·...

HINDUSTAN PETROLEUM CORPORATION LIMITED

ENNORE TERMINAL PROJECT

Tenderer’s Signature with seal: Date:

SECTION-10 of 1

©2010 MECON LIMITED. All rights reserved MEC/23KM/T-04/10000028

SECTION – 10

PRICE SCHEDULE

ITEM NO DESCRIPTION OF ITEM UNIT QUANTITYRate (in Rs.)

(inclusive of all taxes & duties but excluding service tax)

Amount (in Rs.) (inclusive of all taxes & duties but

excluding service tax) ( 4 x 5 )

1 2 3 4 5 6A CIVIL AND ARCHITECTURAL WORKS

SECTION - EW - EARTHWORK

EW1

Earthwork in excavation at all depths for sump, drain, ramp,pits, etc., in ordinary soils including the area filled up with fly ash, in both Dryand Wet conditions, including Pumping and Bailing out Surface and Subsoil water, rain water by using any suitable dewatering method,Shoring, Strutting, Slush removal, sorting out the excavated earth into serviceable and unserviceable material,including backfilling in allpositions, in layers of 150mm at all heights and depths as per Drawing and Specifications wherever required , in foundation pits and otherplaces. The cost include transportation of both unserviceable/serviceable material into dumping yards or wherever required as perdirection of Engineer incharge upto any lead within plant boundary,spreading in layers of thickness not more than 200mmTh, watering andcompacting etc., as per specifications and direction of Engineer. The Measurement for payment shall be for the theoretical volume onlyand it shall be the volume of the block of the excavation having maximum bottom dimension of the foundation as per drawing and toactual depth.

CUM 1000

Note:i) The Contractor shall take into account in his rate, the provision for excess excavation for necessary working space,side slope andbackfilling the same.

ii) Existing ground level/T.L shall be recorded jointly before starting of excavation. All survey equipment (like dumpy level etc) shall bearranged by contractor at his own cost.iii) Cost towards dewatering of surface or subsoil water shall be deemed to have included in the quoted rate.

EW-2Supplying and filling approved quality moorum in foundation or under floor, trenches,pits and other places, at all locations in layers of 200mm thickness including watering and ramming, all lead, lift and depth complete as per drawing and specification and direction of theEngineer. CUM 500

EW-3

Controlled earth filling under floors and other places with special compaction to achieve dry density of 95% standard proctor density withapproved earth, reclaiming from spoil heaps as per instruction of engineer at all heights/ depths, transporting, depositing, compaction anddressing, trimming complete as desired in layers not exceeding 15 cms incliuding watering, compaction by mechanical means as perspecifications and instructions of the Engineer.

CUM 500

SECTION TOTAL- EW

HINDUSTAN PETROLEUM CORPORATION LIMITEDENNORE TERMINAL PROJECT

ADMINISTRATIVE BUILDING (GREEN BUILDING) SCHEDULE OF QUANTITIES

Tenderer's Signature with seal:Date:

SECTION-10Page 1 of 32






1 2 3 4 5 6



SECTION - AT - ANTITERMITE TREATMENT

AT-1

Supplying and injecting with approved quality chemical emulsion at the rates and concentrations as per IS 6313-1981 Part II forpreconstructional antitermite treatment and creating a chemical barrier under and alround the column pits, foundation, wall trenches, plinthfilling, junctions of wall and floor, expansion joints, apron, surrounding of pipes, conduits etc., along the perimeter of the building includingall byeworks complete as per specification and direction of Engineer (only ground floor plinth area of the building will be measured for thepayment in the following three stages. i) 50% after completion of the foundations ii) 30% after completion of the ground floor flooring iii)20% after completion of all treatment works including ground floor doors & windows. Work to be executed by M/s Pest Control (India) orany other approved agency and specified guarantee for 10 (ten) years shall be furnished by the tenderer.

SQM 450

SECTION TOTAL- AT








1 2 3 4 5 6



SECTION - CC - PLAIN AND REINFORCED CONCRETE

CC1

Supplying and Laying Plain Cement Concrete of Grade 1:4:8(M7.5) with stone aggregate of 40mm down size (including Shuttering ifrequired) in all levelling courses under Foundation, pile cap,Floors,rigid pavement, Pits,trenches etc., at all depths complete all as perDrawings and Specifications and instruction of the Engineer.

CUM 40

CC2Supplying and Laying Plain Cement Concrete of following Grades (including Shuttering if required) in foundation, screed,floors,aprons,pits,drains and other mass Concrete works, Steps, Coping of wall etc., at all level as per Drawings, Specifications and instruction ofEngineer.a) M-15 Grade Concrete,using SRC with 20 mm down graded coarse aggregate.(for aprons, pits, drains etc.,)

CUM 30b) M-15 Grade Concrete,using OPC with 20 mm down graded coarse aggregate.(for screed, coping of wall etc.,)

CUM 2

CC3

Supplying & laying of design mix reinforcement cement concrete flooring ( using sulphate resistant cement) of thickness as mentioned inthe drawing of following grades in long panels with necessary slope using screed vibrators, etc., in floors and any other works as directed.The rates shall include the cost of necessary steel shuttering (but excluding the cost of steel reinforcement) to maintain the line andlevel of the floor to achieve a flat and smooth surface within the specified tolerance, cleaning and preparing the base surface and othernecessary bye-works, provision for construction joints, expansion joints, etc., all complete as per specification, drawings and direction of theengineer

a) M-20 Grade, design mix, Concrete,using 20 mm down graded coarse aggregate. CUM 70

CC4

Supplying and Laying of design mix,Reinforced Cement Concrete of following Grades (excluding Shuttering and Reinforcement) at alldepths and heights in all types of Foundations, Footings, water sump, slabs of all shapes, and any other works both in sub andSuperstructures all complete with all bye works as per Drawings, Specification and instruction of Engineer.

a) M-30 Grade Design Mix Concrete using sulphate resistant cement (20 mm down graded coarse aggregate.) for under ground watertank including testing as per IS: 3370 CUM 15

CC5

Providing, Fixing and Stripping of Shuttering for all types of shapes using good quality plywood or steel plate on steel frame for all types ofStructures not covered in respective items including Centering / Scaffolding, all bye works complete as per Drawings, Specificationsand directions of the Engineer.

a) For Structures at all depths and heights. SQM 85

CC6

Supplying and Fabricating and Fixing in position Steel Reinforcements at all levels and positions including the Cost of transport,Straightening, Cutting, Bending, Cranking, Binding, Welding, Provision of necessary Chairs and Spacers, Preparation of bar bendingschedule Drawings, getting the same approved etc., as per Drawings and Specifications and including Cost of binding wire, Labour etc., allcomplete for Reinforced Concrete and reinforced brick work and any other place as specified with HCR TMT bars (HCR Fe500 TMT fromSAIL/ Fe500-TISCON-TMT bars from TATA ). The chairs and spacer bars provided will not be Measured for payment.

a) High corrosion resistant TMT bars conforming to Grade Fe-500 of IS1786-1985 MT 4








1 2 3 4 5 6



CC7

Supplying, Fabricating, Fixing at all levels and positions Steel embedments/ Inserts like Plates, chequered plates, angle, Channels,Anchor boxes, Bolt with nuts and washers Bolt caps, MSI pipe Sleeves including Threading etc., including two coats of approvedquality Synthetic enamel paint over a primer coat on the exposed Surfaces wherever necessary, all complete as per Drawings,Specifications and directions of the Engineer ( Jigs, Templates and Fixtures will not be paid separately except for fixing Anchorboxes)

KGS. 25

CC8Providing and mixing of approved water proofing admixture as per the manufacturer's specification including cost of material , complete,with all byeworks as per specification / drawing and instruction of the Engineer.

a) Liquid water proofing compound (Prolapin 421 IC/Plastocretes - N or equivalent) LITRE 75

CC9

Roof screed with M-15 grade concrete using Portland pozzolona cement with fly ash content minimum of 15% (12 mm down graded coarseaggregate) with smooth finish and required slope(min. 25 mm thick & max. 125 mm thick) including mixing of water proof compound asper manufacturer's specification complete with all bye works .The payment for water proofing compound will be done under relevant item

CUM 45

SECTION TOTAL -CC








1 2 3 4 5 6



SECTION - MN - MASONRY WORKS

MN1

Providing and constructing Autoclaved Aerated Block (A.A.C) Masonry works consisting of 70% of fly ash content in CM 1:6 usinglocally manufactured (within 800 kms form project site) A.A.C BLOCKS of size 600x200x200mm. Minimum Compressive strength of 3N/mm2 and conforming to IS:2185 ( Part - 3 ) for all types of masonry works, foundation and drain at all depths and heights includingproviding openings and projections, raking of joints, scaffolding and curing etc., complete as per specifications,drawings and direction ofthe Engineer.

CUM 200

MN2

Providing and constructing Autoclaved Aerated Block A.A.C BLOCK MASONRY WORKS 100 mm thick consisting of 70% of fly ashcontent and manufactured locally (within 800 kms form project site), having minimum Compressive strength of 3 N/mm2 andconforming to IS:2185 ( Part - 3 ), in 1:4 cement mortar, including providing reinforcement at every 3rd courses with 2 MS bars of 6 mmdia. and distribution 6 mm dia at 30 cm centres to centres in all locations and heights, as per drawing and as directed by engineer includingfilling of joints with CM 1:4 and racking of joints.(Reinforcement will not be paid separately)

SQM 150

MN3

Providing BRICK WORK 110 mm thick using locally manufactured (within 800 kms from project site) fly ash bricks, having crushingstrength of not less than 75 kg/cm2, in 1:4 cement mortar, including providing reinforcement at every 3rd courses with 2 MS bars of 6mm dia. and distribution 6 mm dia at 30 cm centres to centres in all locations and heights, as per drawing and as directed by engineerincluding filling of joints with CM 1:4 and racking of joints.(Reinforcement will not be paid separately)

SQM 50

MN4

Providing and constructing FLY ASH BRICK MASONRY WORKS in CM 1:6 using using locally manufactured (within 800 kms fromproject site) bricks of size 230x110x70mm. Class designation 75kgs/cm2 and conforming to IS:12894 for all types of foundation and drainat all depths and heights includng providing openings and projections, raking of joints, scaffolding and curing etc., complete as perspecifications,drawings and direction of the Engineer.

CUM 25

SECTION TOTAL - MN








1 2 3 4 5 6



SECTION - FN -PLASTERING & SURFACE FINISHES

FN1

Providing 20 mm thick external sponge finish cement plaster 1:4 using Portland Pozzolona cement with content of flyash minimun 15%(1 cement : 4 sand) , at all depths and heights in two layers of 12mm & 8mm. 2nd later 8mm shall be finished with sand faced plastering onfaces of walls, pillars, projection, bands, cornices, fins, sills, etc., including raking out joints if any left out, necessary dabbing, curing,scaffolding,complete with all bye works at all heights as per specification and drawings, second layer with water proofing compound (to bepaid under relevant items).

SQM 1400

FN2

Providing 12 mm thick cement plaster 1:4 (1 cement : 4 sand)using Portland Pozzolona cement with content of flyash minimun 15%smooth finish at all depths and heights in one layer on internal faces of walls, pillars, projection, bands, cornices etc., including necessarydabbing, curing, scaffolding, etc.,complete with all bye works at all heights as per specification and drawings.

SQM 1500

FN3

Providing 6 mm thick cement plaster 1:3 (1 cement : 3 sand)using Portland Pozzolona cement with content of flyash minimun 15% toceiling of slabs, chajjas including drip course, bands, beams, columns, loft slabs, staircases, and any other location at all heights whereverrequired with all bye works dabbing, curing, scaffolding, etc.,complete at all heights and levels as per specification and drawings.

SQM 1100

FN4

Providing 12mm thick cement plaster CM 1:4 (1 cement : 4 sand) to apron, drain and any other location at all heights including floatingcoat of neat cement @ 2.2 kg/sqm wherever required with all bye-works dabbing,curing,complete all heights and levels as per specificationand drawings and as directed by engineer.

SQM 275

FN5Providing drip mould of size 20mm x 8mm over cement plastering of chajjas, roof projections etc. at all heights and levels in cementmortar 1:3, hacking, curing, scaffolding etc at all heights and lifts, all complete as per specifications and instructions of the EngineerIncharge. RM 200

Providing and fixing of Arpitha Plaster mesh made out of galvanized iron of nominal thickness 0.35 mm with a Zinc coating of 120 gmsper Sqm at the junctions of Masonry and concrete works 100mm to150 mm Width, chasing Works 200 mm Width, Diagonal Fixing at Doors& Windows Opening to a width of 300 mm x 600 mm including tying in position with suitable nails / screws etc., complete and as permanufacturer specification, Rate shall include for preparation of surface, cleaning, curing etc. complete, all as directed by the engineer incharge

a) 200mm wide RM 270b) 300mm wide RM 150

FN6








1 2 3 4 5 6



FN7

Providing and applying two coats of acrylic oil bound washable distemper- Eco friendly paint with low Volatile Organic Compounds( not exceeding 50 g/L ) over internal plastered surfaces, of approved shade & make over one coat of approved cement primer consistingof volatile organic compounds less than 250g/L, including preparing the surfaces by applying BIRLA WHITE Wall Care Putty (Finefinish) , 1.5mm thick, surface preparation, cleaning and all byeworks, filling hair cracks with putty / approved filler wherever required,scaffolding & cleaning, cost of all materials, labour etc. at all heights and lifts, all as per drawing, specifications and as directed by EngineerIncharge etc. complete.

SQM 1500

FN8

Providing and Applying of painting on internal plastered surfaces with two coats of acrylic emulsion - Eco friendly paint with low VolatileOrganic Compounds ( not exceeding 50 g/L ) of approved shade & make, over one coat of approved cement primer consisting ofvolatile organic compounds less than 250g/L, including preparing the surfaces by applying BIRLA WHITE Wall Care Putty (Fine finish)1.5mm thick, surface preparation, cleaning and all byeworks, filling hair cracks with putty / approved filler wherever required, scaffolding &cleaning, cost of all materials, labour etc. at all heights and lifts, all as per drawing, specifications and as directed by Engineer Incharge etc.complete.

SQM 1000

FN9

Providing and Applying of painting on steel surfaces with two coats of synthetic anti corrosive enamel- Eco friendly paint with lowvolatile organic compounds ( limit not exceeding 250g/ ) of approved shade, & approved make, over one coat of approved wood / steelprimer including preparing surfaces, filling with putty wherever required, scaffolding & cleaning cost of all materials,labour etc. at all heightsand lifts, all as per drawing, specifications and as directed by Engineer Incharge etc. complete.

SQM 25

FN10Providing and applying spectrum wall textured finish - Eco friendly paint with low Volatile Organic Compounds ( not exceeding 50g/L ) of approved pattern and shade over internal / external wall surface at all levels and heights including all bye works etc., complete asper specifications and instructions of the Engineer Incharge.

SQM 450

FN11

Providing and applying two coats of water based 100% acrylic exterior emulsion - Eco friendly paint with low Volatile OrganicCompounds ( not exceeding 50 g/L ) over a coat of approved primer consisting of volatile organic compounds less than 250g/L,which in turn shall be applied over a coat of colourless biowash of approved make over external concrete/masonry/plastered surfaces asantifungal treatment including prior washing of the surface with clean water, removal of dirt, debris etc. at all heights and levels, includingsurface preparation, scaffolding at all locations and heights with all byeworks complete as per manufacturer's specification and direction ofthe Engineer Incharge.

SQM 1000

SECTION TOTAL - FN








1 2 3 4 5 6



SECTION - FL - FLOORING,PAVING & FACING

FL1

Providing and laying poly vinyl chloride sheet 2mm thick (conforming to IS:3462) of approved shade and sizes using approved rubber based adhesive VOC limit not exceeding 60g/l and shall be pressed properly to avoid undulations and air bubbles, to correct line andlevel, all complete as directed by the Engineer. The joints between the sheets shall be suitably fused/ cautered to make the entire surface seamless. The base surface shall be cleaned thoroughly to make it absolutely dust free and damp free before laying of the sheets. ThePVC sheets shall be brought to site in rolls of at least 1.50m wide and 20m long. The entire surface shall be thoroughly cleaned withcleaning liquid and soap water before handing over. The measurement shall be as per net surface area in laid condition.

a) In flooring SQM 5b) In skirting SQM 10

FL2Providing & laying polished granite procured within 800 kms from project site for skirting including 12 mm thick cement motor of mix 1:3backing, finishing the joints,curing and all bye-works complete

a) 10 mm thick polished granite of approved shade & size with half bull nosing SQM 10

FL3Providing & laying polished granite slabs procured within 800 kms from project site for flooring over and including 20 mm thick cementmortar bed of mix CM 1:4,finishing the joints, curing & all bye-works complete

a) 20 mm thick polished granite slab of approved shade & size SQM 15

Providing and laying ceramic tiles with a recycle content of 35-55% of Group - I classification, conforming to IS:13754 of approvedcolour at all levels and locations with necessary specials etc. using approved first quality tiles as shown in the drawing laid over andincluding minimum 15 mm thk. CM 1:3 backing and tile fixing adhesive with volatile organic compounds not exceeding 65 g/l mixed to cement paste used for fixing the tiles, joints filled with white cement mixed with matching shade of pigment etc. at all leads and lifts,complete with all byeworks as per specification and direction of Engineer Incharge.

a) Dado using 300 x 200 mm tilesi) White color SQM 40ii) Light shades SQM 30iii) Dark shades SQM 100

Providing and laying anti-skid ceramic tiles with a recycle content of 35-55% of Group - IV classification, conforming to IS:13754 andof approved colour at all levels and locations using approved first quality tiles in flooring of toilets, pantry etc. and as shown in the drawinglaid over and including minimum 35 mm bed (CM 1:3) joints filled with white cement mixed with matching shade of pigment etc. at all leadsand lifts, complete with all byeworks as per specification and direction of Engineer Incharge

a) 300mm x 300mm x minimum 7.7mm thk. in flooringi) Light shades SQM 80ii) Dark shades SQM 20b) 300mm x 300mm x minimum 7.7mm thk. in skirting of light shade SQM 10

FL4

FL5








1 2 3 4 5 6



FL6

Supplying and laying prepolished designer concrete tiles of approved shade and design from approved manufacturers of sizeapproximately 300 mm x 300mm x 20 mm thick laid over minimum 30mm thick mortar bedding in CM 1:4, close jointed & pointed withmatching shade of pigment mixed with white cement slurry, finished to levels, slope or plumb as required, including curing, polishing etc atall leads and lifts, complete as per specifications, drawings and instructions of the Engineer Incharge.

SQM 15

Providing & laying/fixing in position 18 to 20 mm thick machine polished granite slabs procured within 800 kms from project site ofapproved colour & quality including machine/handcut, polishing, buffing the edges all in line, level, making curvature of all exposed edgesand their due polishing, in 20mm thk. cement mortar 1:3 with best workmanship, finishing, curing, complete in shelves, for counter top ofwash basin, sills, jambs, facias etc.at all leads and lifts, as per drawings, specifications and instructions of the Engineer Incharge.

a) Black shade. SQM 20

Providing and laying 20 mm thick polished granite slabs procured within 800 kms from project site with bull nosing and partly flamed, making curvature of all exposed edges and their due polishing, over 20 mm thick 1:3 CM backing for treads of staircase and entrancesteps etc. at all leads and lifts, complete as per drawings, specifications and directions of Engineer Incharge.

a) Ruby red shade. SQM 50

FL9Providing and laying 18mm thick polished granite slabs procured within 800 kms from project site , over 12 mm thick 1:3 CM backingfor risers of steps and skirting of staircase and entrance steps etc. complete at all leads and lifts, as per drawings, specifications anddirections of Engineer Incharge.

a) Black Shade SQM 10

b) Light shades. SQM 25

FL10

Providing & laying/fixing in position first quality black 40 mm thick machine cut machine polished granite slab procured within 800kms from project site in single piece laid over 20 mm thick cement mortar bedding 1:3 in support areas with best workmanship, makingcurvature of all exposed edges and their due polishing, providing necessary holes, finishing, curing etc. at all leads and lifts for platforms in pantry etc.as per drawings, specifications and directions of Engineer Incharge.

SQM 5

FL11

Providing and laying wooden flooring of approved colour and design of wooden strips of width 100 to 200mm and 600 to 2400 in lengthand thickness of 14to 18 mm from Parky / Tarkett/Armstrong or equivalent ( consisting of Floor Score Standard Certification ) the costincludes, levelling of base floor and using adhesives which contain VOC content not exceeding 100 grams/liter as per specification /instructions of the Engineer Incharge.

SQM 80

FL7

FL8








1 2 3 4 5 6



FL12

Providing and laying vitrified ceramic tiles of approved colour and design at all levels and locations using approved first quality tiles inflooring with or without spacers as shown in the drawing, laid over a bedding of cement mortar bed of mix 1:4 to achieve overall flooringthickness as 50mm and a backcoat of white cement slurry and joints filled with white cement mixed with matching pigment complete with all byeworks like covering with plaster of paris, curing etc. at all leads and lifts and as per specification / instructions of the Engineer Incharge.

a) Using 900mm x 900mm x minimum 11.50mm thk.with glossy finish SQM 200b) Using 900mm x 900mm x minimum 11.50mm thk.with MATT finish SQM 50c) Using 600mm x 600mm x minimum 8.50mm thk.with MATT finish SQM 400d) Using 600mm x 600mm x minimum 8.50mm thk.with glossy finish SQM 100

FL13

Providing and laying vitrified ceramic tiles of approved colour and design at all levels and locations using approved first quality tiles inskirting with or without spacers as shown in the drawing, laid using approved tile fixing adhesive and joints filled with white cement mixedwith matching pigment complete with all byeworks, curing etc. at all leads and lifts and as per specification / instructions of the EngineerIncharge

a) Using 900mm x 900mm x minimum 11.50mm thk.with glossy finish SQM 10b) Using 900mm x 900mm x minimum 11.50mm thk.with MATT finish SQM 10c) Using 600mm x 600mm x minimum 8.50mm thk.with MATT finish SQM 20d) Using 600mm x 600mm x minimum 8.50mm thk.with glossy finish SQM 20








1 2 3 4 5 6



FL14Providing and fixing inner corner tile beading / external roundage tile beading of nominal thickness 1.2mm of suitable colours anddepth of 10.5mm made out of PVCU and PVC co-extrusion as protector for tile inner corners and external edges for all vertical andhorizontal corners and edges at all leads and lifts as per manufacturer's specifications from M/s Arpitha Exports.

RM 70

FL15Providing and laying interlocking concrete paving block in open pavements, paths, porticos etc., over 50 mm thick sand bed using 80 mm thick paving blocks of grade M30 and of approved design pattern and approved brand with necessary compaction etc. complete asper specifications and instructions of the Engineer Incharge.

a) using grey paving blocks SQM 200b) using coloured paving blocks SQM 50

FL16Providing hard core with hard granite stone boulders including laying, packing, filling interstices with good quality spalls, dry and wetconsolidation with mechanical means, binding with good quality moorum(cost inclusive) with all bye works complete all as perspecification,drawing and instruction of the Engineer (Consolidated thickness will be paid).

a) for aprons and flooring CUM 125

FL17 Providing and laying of broken white glazed china mosaic tiles of uniform thickness for roof insulation over cement mortor bed (1:4)of thickness 20 mm as mentioned in drawings and as per the instructions of site incharge.

SQM 520








1 2 3 4 5 6



FL18

Providing and fixing of 500 mm high cavity floor of modular 600 x600 mm approximate with pre moulded access floor tile made fromsteel and cementatious in fill material from approved manufacturer unitile or equivalent with edge beading and faced with 2 mm thickantistatic high pressure laminates at all leads and lifts.The panel shall be placed on GI snap lock grid system stringers channel supportedover MS galvanised pedestal supports of minimum16 mm ID at 600 mm c/c approximate both ways. The pedestal supports shall be rigidlyfixed on to the floor with glue and mechanical fasteners and shall be of 100x100x8 mm thick base plate and minimum 19 mm thick MSstools with coupling and check nut for level adjustment. The work includes necessary openings for cables and panel mounting and cuttingof tiles to required size and strengthening of pedestals with 300 x 300 mm RCC pedestal at location of panels. The floor panels andstringers shall be completely removable ans shall remain in position in position without screwing.The shade of flooring material shall be asspecified in drawing or as directed by includes supply of 1% spare tiles and pedestals, lifting tools and whole system shall have fire rating of two hours.

SQM 140

Providing and laying granolithic flooring with total thickness as given below, laid monolithically over base concrete in panelswith a maximum panel area of 2.50 sqm. at all locations and heights including skirting etc., with under bed consisting of plaincement concrete 1:2:4(1 cement:2coarse sand:4stone chips, 12mm and down) and topping of mix 1:1:1(1cement:1mediumsand:1fine stone grit upto 3mm size), supplying and fixing 1.5mm thick aluminium strip for full depth, chequring in floor finishinclusive if required, rounding, sloping,curing, finishing etc., all as per specifications, drawings and directions of the Engineer.

40mm thick with 30mm under-bed and 10mm topping mixed with non-metallic floor harderner as per manufacturer'sspecification and instructions(Fosroc, Sika or equivalent)

SECTION TOTAL - FL

FL19

SQM 150








1 2 3 4 5 6



SECTION - WW - WOOD WORK

Providing & fixing colour coated aluminium hardware fittings with approved quality and shade as per IS specifications/as approved by engineer to woodwork with cadmium plated MS screws, suitable sockets in masonry/concrete surface if required including all bye-works complete as per specification, drawing and instruction of engineers (fittings shall not be paid separately in composite items which specify inclusions of fittings)

a) Butt hinges (extruded section 125 mm x 63 mm x 4 mm) each 60

b) Tower bolts (with barrel & bolts of extruded section - (i) 250 mm x 12 mm (bolt size) set 30(ii) 150 mm x 10 mm set 15

c) Sliding door bolts including locking arrangement(aldrop) (I) 250 mm long x 16 mm dia rod set 10

d) Grip handle without back plate of approved IS brand (i) 150 mm long each 30

e) floor stopper of double type for door shutters up to 40 mm thick(I) rubber - double type each 10

f)Door handle 150 mm long each 15

Providing & fixing Godrej Mortice dead lock with back plate, duplicate keys & other fixtures complete with all bye-works as per specification and instruction of the engineer

a) with 6 levers (depth 76 mm) set 5

WW2

WW1








1 2 3 4 5 6



Supplying and fixing exterior grade FSC CERTIFIED, Eco Friendly block board flush board shutters fom Greenply or equivalent of thethicknesses and finishes mentioned below bonded with Un-extended synthetic resin consisting of Volatile Organic compoundscontent not exceeding 30 g/l with composed core including single hung in doors, wardrobes, cupboards, conforming to IS 2202,specification from approved manufacturer all bye works complete as per specification and drawing, at all locations with necessary sandblocks, cleats wherever required. The shutters shall be supplied with teakwood internal edge lipping from factory and 6mm external edgelipping shall be provided at site.All works shall be as per specifications, drawings and instructions of the Engineer Incharge.

a) 1.5 mm thk. lamination of approved shade,design and brand, glued with synthetic rubber based adhesive of approved make on both faces.

1) 25mm thk. SQM 202) 32 mm thk SQM 15

b)32mm shutter with decorative teak veneer on one side and commercial finish on the other side with necessary approved polish / varnish.SQM 20

WW4 Providing Vision Panel in door shutters including making the opening, providing necessary teak wood frame work & fixing 6 mm clearfloat glass with teak wood beading all round on both faces etc. complete as per the specifications and direction of the Engineer Incharge.

SQM 10

SECTION TOTAL - WW

WW3








1 2 3 4 5 6



SECTION - ST - STEEL & IRON WORK

ST1

Supplying and fixing pressed steel frames manufactured from commercial steel sheet 1.6mm thick and butt welded at the corners, fordoor frames including SS hinges (KICH make as shown in drawings), lock jambs, beads, brace ties, adjustable lugs jammed in PCC blocks1:2:4 , lock strike plate, shock absorbers, including two coats of synthetic anti corrosive enamel- Eco friendly paint with low volatileorganic compounds ( limit not exceeding 250g/ )over a coat of primer consisting of volatile organic compounds less than 250g/L, filling the frame with cement mortar 1:5 all complete at all heights and levels as per IS 4351 and drawings, specifications and instruction ofthe Engineer Incharge. SS hinges shall be paid for under relevant item.

a) 105mm (Profile - A) RM 30

b) 125mm (Profile - B) RM 50

ST2

Supplying and fixing Grills/Guard bars made out of MS square bright bars, flats including fixing in concrete / masonry walls / jambs /frames including two coats of approved synthetic anti corrosive enamel- Eco friendly paint with low volatile organic compounds (limit not exceeding 250g/ )over a coat of primer consisting of volatile organic compounds less than 250g/L, at all heights and levelsas per drawings and specifications, instructions of the Engineer Incharge.

1) Fixing using MS lugs embedded in 1:2:4 concrete blocks KGS 300

ST3

Supplying and fixing Stainless Steel Handrail, Baluster system, connecting bars etc for staircase,ramps etc from KICH or equivalentwith Anti - corrosive high grade AISI 316, with adjustable top baluster systems to place the handrail of 50 mm dia, caps to cover mountingbolts, fixing rigidly to the floor with plate embedded in concrete 1:2:4 including provision for connecting bars at regular intervals , soldering /welding, proper buffing etc. complete at all heights and levels as per drawings, specifications and instructions of the Engineer Incharge.

KGS 700

ST4Supplying and fixing anticorrosive high grade SS Handrails of AISI 316 grade and specified diameter (1.6mm thk.) of approved makeKICH or equivalent fixed to walls including soldering / welding, proper buffing etc. complete at all heights and levels as per drawings,specifications and instructions of the Engineer Incharge.








1 2 3 4 5 6



a) 50mm dia RM 75

ST5

Fabricating, supplying & fixing in position steel doors for cupboards consisting of 16 G CRCA sheet for shutters (single side) & stiffeners& 14 G. CRCA sheet for frame & including providing & fixing standard hardware & accessories, locking arrangement, tower bolts, louversat top & bottom, fixing with screws, nuts, bolts, washers etc. painting one coat of steel primer etc., at all heights and levels as per drawing,specifications and instruction of the Engineer Incharge.

SQM 20

SECTION TOTAL - ST








1 2 3 4 5 6



SECTION AL - ALUMINIUM WORK

Providing & fixing in position aluminium doors, windows, ventilators, louvres, fixed glazing, double glazing, sliding windows, aluminium rough ground etc. with extruded & integral colour powder coating with minimum 60 microns, Aluminium sections, Powder coated Aluminium beadings,Powder coated Aluminium profile panel sheets, manufactured to relevant I.S. codes & using minimum 2mm thick (or as specified) heavy sections from environmentally compatible products containing minimum of 15 to 25 % of recycled content and shall be manufactured within 800 kms from project site from Jindal / Indal manufacturer or equivalent including cost of providing required no. of heavy duty stainless steel butt hinges, pivots, approved door and windows handles, EPDM Gasket, PVC/Neoprene Gasket Lining, Stainless steel screws, mastic filling, weather strips, tower bolts,nuts, washers, rollers etc. as required and as per drawing etc. all complete at all heights and as directed by the Engineer-in-Charge. The rate shall also include giving a coat of bitumastic paint on the aluminium surfaces in contact with masonry / concrete and closing the gaps around the frame and the adjoining surface with approved silicone sealant with volatile organic compounds content less than 250 g/l on both faces to achieve watertightness.

Note:

1. Payment will be made on the basis of weight of aluminium members/sections fabricated & actually installed in position without extra allowance for wastages. No extra payment will be made for all non-aluminium consumable items like screws, gasket, weather strips, PVC/Neoprene lining and butt hinges, tower bolts etc.

2. Glazing, Particle Boards, aluminium grills, mesh etc. will be measured and paid separately under relevant item.

3. All fitting shall be of matching colour powder coated aluminium sections.

4. The aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherver required including cleat angles at no extra cost.

Providing and fixing heavy duty double action hydraulic floor springs of approved make with ISI mark, pivoting and all otherarrangements including cost of cutting floors,S.S cover Plates with brass pivots etc. complete and other necessary accessories required forthe works to facilitate smooth operation of the door shutter at all leads and lifts, all as directed by the Engineer- incharge.

1) Double action floor spring EACH 5

800

AL2

AL1

KGS








1 2 3 4 5 6



AL3Providing and Fixing Sleek Model heavy duty Hydraulic Door Closer Everlite / Gamish / Hyper make with ISI mark and with necessaryscrews, fixing to the aluminium / glass / wooden door complete as per drawing, specifications including all labour, transporting etc. at allleads and lifts and as directed by the Engineer-in-charge complete.

EACH 10

AL4

Providing and fixing powder coated with minimum thickness of 60 microns aluminium structural glazing of approved shade and qualityfrom environmentally compatible products containing minimum of 15 to 25 % of recycled content and shall be manufactured within 800 kms from project site from JINDAL / INDAL Aluminium manufacturer or equivalent using approved sections for mulions andtransomes etc. with 6mm thick toughened clear float glass as per drawing with all necessary accessories, assembling and fixing it toconcrete / masonry wall with screws and rawl plugs and necessary clamps with nylon washers and fasteners for fixing frames. andincluding butyl sealants with VOC content less than 250 g/l on both sides, EPDM gaskets, weather strips etc. Glass shall be measuredand paid for separately under respective item.

KGS 135

AL5Providing & fixing prelaminated Medium density fibre (MDF) board infill panels of approved shade and brand GREENPLY or Equivalentfor doors, cabinets, shelves etc. at all leads and lifts as per specifications and instructions of the Engineer Incharge.

a) 12mm thk. SQM 15

AL6

Providing and fixing in position powder coated with minimum thickness of 60 microns fixed AL louvers made of box sections, sheets,angles etc for external duct area using Powder coated aluminium sections of approved shade and quality from environmentally compatibleproducts containing minimum of 15 to 25 % of recycled content and shall be manufactured within 800 kms from project site of size100mm x 40mm x minimum 2mm thk. and of approved shade fixed to aluminium box frame work, leaving a gap of 125mm approx. betweensections all complete at all heights and levels as per drawing and instructions of the Engineer Incharge.

KGS 170

SECTION TOTAL - AL








1 2 3 4 5 6



SECTION-MS-MISCELLANEOUS

MS1

Providing & fixing in position Frame less sensor operated glass double shutter sliding doors with 12 mm thick toughened glass withapproved etching design manufactured to relevant I.S. codes from approved manufacturer including cost of activators, switches, track andmounting profile, Carrier, Door suspension device with adjustable fixture, Motor with decoder, Track rail, Return pulley, Basic module,control with integrated switched power supply unit and multi-way connectors for optional expansion modules, Door stop etc.Dorma Make orEquivalent as required all complete at all heights and as directed by the Engineer-in-Charge.

SQM 4

MS2

Providing & fixing in position Frameless Glass side hung doors with 12 mm thick toughened glass with approved etching designmanufactured to relevant I.S. codes from approved manufacturer including cost of providing necessary patch fittings,door closer, floorsprings including handles from KICH / Ozone or equivalent approved S.S handles, door closing & locking arrangements etc. as requiredall complete at all heights and as directed by the Engineer-in-Charge.

SQM 55

MS3Supplying and fixing Stainless Steel signage board (1.5mm thk. sheet conforming to AISI 316 grade with matt finish of KICH make) withvinyl computerised cut letters of approved shade and size , fixing over walls etc. with SS screws, all complete as per drawings,specifications and instructions of the Engineer Incharge.

SQM 5

Providing & fixing float glass of the following specifications SHGC - 0.25 to 0.3, U Value 1.8W/sqmtk or lesser, VLT 35to 45 and ofapproved make of following thickness in windows, doors, ventilators, partitions etc. with necessary clips, beadings etc. complete. Only theclear opening of glass shall be measured for payment.

a)4mm thick float glass. SQM 100b)5mm thick float glass. SQM 150c) 6mm thick toughened clear float glass SQM 30

MS5

Providing and fixing 4mm thick grounded / frosted glass of the following specifications SHGC - 0.25 to 0.3, U Value 1.8W/sqmtk orlesser, VLT 35to 45 and of approved make of in windows / ventilators with necessary beadings and completion as per drawings andinstructions of Engineer Incharge SQM 10

MS6Providing & fixing 50mm dia UPVC pipes for spouts, weep holes etc. including cutting of pipes as required, complete as perspecifications, instructions of the Engineer Incharge. RM 15

MS4








1 2 3 4 5 6



MS7Supply and installation of MS fan boxes of 100mm dia and 75mm height (round shape) made out of 14 SWG MS sheets with stovedSiemens gray paint. All fan boxes shall be flush mounted on ceiling and shall have 4 nos. of 25mm dia holes punched in all four directions,as laid as per the instructions of the Engineer Incharge.

EACH 30

MS8Providing and fixing in position Transparent Poly Carbonate multiwall sheets of 10 mm thickness of approved shade and pattern fromapproved manufacturer including cost of providing necessary fittings like EPDM gaskets, Cap Washers, screws etc all complete as perdrawings, specifications and instructions of the Engineer Incharge.

SQM 25

Providing and fixing UPVC rainwater pipes of the following size and dimensions as per IS : 13592 with necessary specials like bend, shoeetc. fixed with PVC clamps as per manufacturers specifications with all bye works etc. at all leads and lifts as per drawings, specificationsand instructions of the Engineer In charge.

i) 110 mm dia pipe with 2.7 mm thicknessRM 100

Providing broken flyash brick bat for filling in the sunken portion of toilets, bath room etc. as per specifications and instructions of theEngineer Incharge.

Note :

The measurement shall be on cum basis. No deductions shall be made for the areas occupied by pans & other fittings & fixtures.

MS11

Providing and applying waterproofing treatment in floors and vertical surfaces in sunken of toilets and bathrooms etc. with twocomponent acrylic polymer based flexible cementitious coating of heavy duty flexible coating system with excellent waterproofingusing products of approved make. 10mm Cement/Sand (Ratio 1:4) protective screed, using Integral Waterproofing Compoundadded as per manufacturer's specifications, shall be applied on top of the membrane. All works shall be carried out as perspecifications and manufacturer's instructions including all byeworks and at all heights and levels and also as per the directionsof the Engineer Incharge.

SQM 70

MS12Supplying and fixing in positon Reflective Sun control films of TURF GREEN shade with visible light transmission of 50% or more fromGARWARE SUNCONTROL FILMS / EQUIVALENT at all heights as per drawing and instructions of engineer in charge

SQM 150

MS13Supplying and fixing clear BIRLA 3M Scotch Shield safety and security film over glass panes of doors, windows, ventilators, structuralglazing with 3M's adhesive to bond tightly to the glass, all complete byeworks etc.at all leads and lifts as per manufacturer's specificationsand instructions of the Engineer Incharge. SQM 50

SECTION TOTAL - MS

MS9

MS10

CUM 20








1 2 3 4 5 6



[SW] SANITARY & WATER SUPPLY

SW1Providing and fixing 100 x 75 mm HCI floor/Nahani trap with CP hinged heavy brass grating to be fixed in PCC M15 with 20mm down sizeaggregate and made water tight with all bye works complete as per the direction of the engineer.

EACH 15

SW2

Providing and fixing white glazed vitreous china European water closet dual flush model ODEON K - 6286 / HSW 20048 with dual flush of 4/2 litre wall mounted type, double trap syphonic pattern, 'P' or 'S' trap, with low level cistern with cover, flush plates, CP brass barhinges, screws, bolts, rubber, buffers 15mm dia PVC inlet pipe connection and CP brass angle stopcock model JAQUAR Continentalseries No. 053, fixing EWC to wall with necessary brass screws, all complete at all leads and lifts as per drawings, specifications andinstructions of the Engineer Incharge.

EACH 5

SW3

Providing and fixing Indian Green Building Council ( IGBC ) certified white glazed vitreous sensor based urinals HSW-60007/ K8787 of approved make Hindware/ Parryware/ Kohler with less than 1 litre / flush battery operated type with integrated flushing rimused with sensor type spray system for automatic flushing including fixing of urinal in position with necessary specials, brackets,srews etcalong with required plumbing arrangements at all leads and lifts as per drawings, manufacturers specifications and instructions of theEngineer Incharge. (partitions excluded).

EACH 5

SW4

Providing and fixing White glazed vitreous china waterless urinals K4917/ HSW 60017 100 % water saving model of approved makeHindware/ Parryware/ Kohler including fixing of urinal in position along with the catridge required for the operation of waterless urinal withnecessary specials like brackets,srews etc along with required plumbing arrangements at all leads and lifts as per drawings, manufacturersspecifications and instructions of the Engineer Incharge. (partitions excluded).

EACH 1

SW5

Supplying, fitting and fixing over the countertop, white glazed vitreous china oval shaped wash basin of size 560 mm x 410 mmwithout tap holes - model HSW No. 10017 - Washbasin Oval with ISI mark - Installation over the counter type with 15 mm CP brass pillarcock long necked foam flow with flow rate < 2 litre per minute - JAQUAR Continental series No. 021 , 32mm CP brass waste coupling,PVC flexible waste pipe, 15mm PVC inlet water pipe connection, CI cantilever brackets embeddd in 1:2:4 concrete, 15 mm CP brass anglestop cock - JAQUAR Continental series No. 069 , etc. all complete at all leads and lifts as per drawings, specifications and instructions ofthe Engineer Incharge.

EACH 5

SW6

Supplying, fitting and fixing over the countertop, white glazed vitreous china oval shaped wash basin of size 560 mm x 410 mmwithout tap holes - model HSW No. 10017 - Washbasin Oval with ISI mark - Installation over the counter type with Sensor Faucet forWash Basin Complete with Control Box (Battery Operated) - JAQUAR Cat No. 51011 , 32mm CP brass waste coupling, PVC flexiblewaste pipe, 15mm PVC inlet water pipe connection, CI cantilever brackets embeddd in 1:2:4 concrete, 15 mm CP brass angle stop cock -JAQUAR Continental series No. 069 , etc. all complete at all leads and lifts as per drawings, specifications and instructions of theEngineer Incharge.

EACH 4








1 2 3 4 5 6



SW7Providing and fixing box type half-round white glazed channels 100mm size with dead and outlet ends of approved make, set in 80mmthick cement concrete 1:2:4 and joints finished with white cement, at all leads and lifts as per drawings, specifications and instructions ofthe Engineer Incharge. RM 5

SW8 Providing and fixing white glazed vitreous china recessed toilet paper roll holder including roller -model HSW No. 40051 at all leads andlifts as per drawings, specifications and instructions of the Engineer Incharge.

EACH 5

Providing & fixing stainless steel sink of approved make with spout - JAGUAR Continental sink fittings series 309 sink mixer withswinging casted spout, with ISI mark with flow rate < 7 litre per minute, 15 mm CP brass concealed stop cock - JAGUAR Continentalseries No. 069, PVC 32 mm waste pipe & CP brass coupling and CP brass floor trap, mounting on CI bracket / platform, necessarygrouting into walls, gaps finished with white / matching cement etc. complete at all leads and lifts as per drawings, specifications andinstructions of the Engineer Incharge.

a) Stainless steel sink without drain board of overall size 610mm x 460mm with Bowl size 560mm x 410mm x 264mm EACH 2

SW10 Providing and fixing vitreous china white glazed soap tray of superior quality from approved make - HSW No. 40058 model at all leads andlifts as per drawings, specifications and instructions of the Engineer Incharge..

EACH 7

SW11 Supplying and fixing CP brass soap container (Tilting type) of approved make at all leads and lifts as per drawings, specifications andinstructions of the Engineer Incharge. EACH 5

SW12Providing minimum 6mm thick polished float glass mirror, bevelled edge, of approved make fixed to with 6mm thick marine plywoodsheet backing with necessary beading, fixing arrangements all complete at all leads and lifts as per drawings, specifications andinstructions of the Engineer Incharge. SQM 8

SW9








1 2 3 4 5 6



SW13 Providing and fixing CP brass towel rail 600mm long, 20 mm dia - JAQUAR Continental No. 1111 with CP brackets fixed to wall with CPbrass screws and wooden rawl plug, at all leads and lifts as per drawings, specifications and instructions of the Engineer Incharge.

EACH 5

SW14 Providing and fixing CP brass towel ring - model JAQUAR Continental No. 1121 with CP brackets fixed to wall with CP brass screws andwooden rawl plug, at all leads and lifts as per drawings, specifications and instructions of the Engineer Incharge.

EACH 5

SW15 Providing and fixing 15mm CP brass long body bib cock of flow rate < 6 litre per minute with wall flange - JAQUAR Continental seriesNo. 021, at all leads and lifts as per drawings, specifications and instructions of the Engineer Incharge.

EACH 5

SW16 Providing and fixing 15mm CP brass concealed stop cock (extra heavy body) with adjustable wall flange - JAQUAR Continental seriesNo. 083, at all leads and lifts as per drawings, specifications and instructions of the Engineer Incharge.

EACH 5

SW17 Providing and fixing of CP brass health Faucet with 8 mm dia .1 m PVC tube and water hook-JAQUAR allied series No.563, at all leadsand lifts as per drawings,specifications and instructions of Engineer In Charge.

EACH 5

SW18 Providing and fixing CP brass double coat hook - JAQUAR Continental series No. 1161 complete at all leads and lifts as per drawings,specifications and instructions of the Engineer Incharge. EACH 5

Supplying, fitting and laying concealed GI pipes of heavy class of TATA make conforming to IS 1239 with all necessary fittings such asbends, tees, elbows, reducers, unions, nipples, plugs, clamps, fixtures, etc., in masonry / concrete works/ under floors in soils etc. includinglaying in a layer of sand if laid under floors, necessary painting with two coats of anticorrosive black bitumastic paint over a coat ofapproved primer , etc., complete (including chasing and concealing in walls/floors) at all leads and lifts as per drawings, specifications andinstructions of the Engineer Incharge.

a) 40 mm nominal bore RM 5b) 32 mm nominal bore RM 10c) 25 mm nominal bore RM 30d) 20 mm nominal bore RM 40e) 15 mm nominal bore RM 50

SW19








1 2 3 4 5 6



Supplying, fitting and laying concealed GI pipes for of heavy class of TATA make conforming to IS 1239, hot water line with all necessaryfittings such as bends, tees, elbows, reducers, unions, nipples, plugs, clamps, fixtures, etc., in masonry / concrete works including laying ina layer of sand if laid under floors, necessary painting with two coats of anticorrosive black bitumastic paint over a coat of approved primerand insulating the same with 2.5mm thick 95% asbestos magnesia compound of approved make around the pipes and fittings, etc.,at allleads and lifts as per drawings, specifications and instructions of the Engineer Incharge. (including chasing and concealing in walls/floors)

a) 25 mm nominal bore RM 30b) 20 mm nominal bore RM 20c) 15 mm nominal bore RM 20

Supplying, fitting and laying exposed GI pipes of heavy class of TATA make conforming to IS 1239 with all necessary fittings such asbends, tees, elbows, reducers, unions , nipples, plugs, clamps, fixtures, etc., in masonry / concrete works including necessary painting withtwo coats of oil paint over a coat of approved primer complete at all leads and lifts as per drawings, specifications and instructions of theEngineer Incharge.

a) 40 mm nominal bore RM 20b) 32 mm nominal bore RM 30c) 25 mm nominal bore RM 50

Supplying, fitting and fixing superior quality gun metal gate valve (full way) of approved make with ISI mark as per specifications at allleads and lifts as per drawings, specifications and instructions of the Engineer Incharge.

a) 40 mm dia EACH 2b) 32mm dia EACH 3

SW23

Providing SW yard gully trap of size 150x100mm conforming to IS 651, with CI grating 150mm x 150mm and water tight light weight CIcovers (not less than 7.5 Kgs) conforming to IS:1726 of size 300x300mm painted with two coats of bitumastic paint and seated in cementconcrete 1:2:4 including brick masonry in CM (1:4) plastered neatly with 15mm thick CM (1:3) on both faces, 150mm thick PCC bed ofgrade 1:4:8, necessary excavation, dewatering, backfilling, curing etc. complete at all leads and lifts as per drawings, specifications andinstructions of the Engineer Incharge.

EACH 5

SW24

Providing and fixing 18mm to 20mm thick pre polished granite dividers of approved shade in between two urinal stalls with all exposededges bull nosed, fixing to the wall at all leads and lifts as per drawings, specifications and instructions of the Engineer Incharge. Ratesshall include grouting the divider into the wall 100mm deep and making good the surface. The exposed area will be 900 mm x 450 mm(width).

EACH 5

SW20

SW21

SW22








1 2 3 4 5 6



Providing and fixing brass ball valve with high pressure copper floats (horizontal plunger type) conforming to IS 1703 of the followingnominal bore along with necessary socket, backnut, reducers etc. complete with all byeworks at all leads and lifts as per drawings,specifications and instructions of the Engineer Incharge.

a) 32mm NOS 5

Providing & fixing and / or laying centifugally cast iron spun pipes and soil, waste pipe including ventilating pipe with all necessaryfittings and accessories like specials, bends, single and / or double, equal/unequal branches of required degrees with or without ovalaccess door, offsets of required projection, hill rest bend, inverted branch of required degree, traps, wire baloons (galvanised), plugs, cowl,clamps etc., all conforming to IS 3989 bearing ISI mark , of approved make, including spun yarn and lead caulked joints conforming to IS3114, 2 coats of paint, with all leads and lifts, all complete as per specification and direction of Engineer Incharge.

a) Overground condition (with 2 coats of approved synthetic enamel paint over a coat of primer)1) 100mm dia pipe RM 252) 80mm dia pipe RM 40

b) Underground condition (with 2 coats of approved black anticorrosive bitumastic paint) . Excavation shall be paid separately underrespective item.

1) 100mm dia pipe RM 252) 80mm dia pipe RM 10

SECTION TOTAL - SW

SW25

SW26








1 2 3 4 5 6



B INTERIOR WORKS

IW1

Providing & installing in position Eco-Friendly MDF board paneling on walls using' MDF board' manufactured from 100% renewable andsustainable wood resources from GREENPLY / Equivalent with 1.5 mm thk. lamination of approved shade,design and brand, glued withUn-extended synthetic resin consisting of Volatile Organic compounds content not exceeding 30 g/l of approved make on exposedside comprising of G.I metal stud concealed frame work, floor & ceiling channels, 12mm thick MDF panels IS:12406 (Interior Quality) fixedwith necessary screws/bolts, drilling holes in ceiling, floor or walls fixing with anchor fasteners, square and tapered edges of the board tobe jointed, as per the manufactures specification drawings and instructions of Engineer in charge.

SQM 200

IW2

Providing and installing in position seamless false ceiling with 12.5 mm thick Gypsum plasterboard with water repellent additivesconsisting of 30 - 60% of recycle content from Gyproc India (M/s. India Gypsum), with standard and approved GI supporting arrangementsuspended from RCC slab with all accessories such as screws, cleats, adjustable suspension rods, runners and Tees etc., includingmaking suitable openings for light fittings etc., and painting false ceiling board with two coats of approved make and shade acrylic emulsion - Eco friendly paint with low Volatile Organic Compounds ( not exceeding 50 g/L ) over and a coat primer consisting ofvolatile organic compounds less than 250g/L complete with all bye works at all locations and heights with extra runners, using tape etc.to give a seamless look and as per drawings and manufacturers specifications and instruction of Engineer Incharge.

SQM 75

IW3

Providing and installing in position seamless false ceiling with 12.5 mm thick Gypboard consisting of 30 - 60% of recycle content fromGyproc India (M/s. India Gypsum), with standard and approved GI supporting arrangement suspended from RCC slab with all accessoriessuch as screws, cleats, adjustable suspension rods, runners and Tees etc., including making suitable openings for air-conditioning grill,light fittings, troughs etc., and painting false ceiling board with two coats of approved make and shade acrylic emulsion - Eco friendlypaint with low Volatile Organic Compounds ( not exceeding 50 g/L ) over and a coat primer consisting of volatile organic compoundsless than 250g/L complete with all bye works at all locations and heights including corbelling/ moulding etc. with extra runners, using tapeetc. to give a seamless look and as per drawings and manufacturers specifications and instruction of Engineer Incharge.

SQM 600








1 2 3 4 5 6



IW4

Providing and fixing in position false ceiling with 12.5 mm thick Gypsum tiles with perforations consisting of 30 - 60% of recyclecontent from Gyproc India (M/s. India Gypsum , of size 595 x 595 mm , with standard and approved precoated GI supporting arrangementsuspended from RCC slab with all accessories such as screws, cleats, adjustable suspension rods, runners and Tees etc., includingmaking suitable openings for air-conditioning grill, light fittings, troughs etc., and painting false ceiling board with two coats of acrylic/plastic emulsion paints of approved make and shade over and a coat of primer complete with all bye works at all locations and heights andas per drawings and manufacturers specifications and instruction of Engineer Incharge.

SQM 200

Providing & installing in position Gypsum partition using 'Gyp board' consisting 30-60 % recycle content manufactured by Gyproc India (M/s. India Gypsum) or equivalent comprising of G.I metal stud concealed frame work, floor & ceiling channels, 12.5mm thickGypboard panels on both sides fixed with necessary screws / bolts, drilling holes in ceiling, floor or walls fixing with anchor fasteners,applying jointing compound & paper tapes sanding & finishing with top coat with two coats of approved make and shade with acrylic emulsion - Eco friendly paint with low Volatile Organic Compounds ( not exceeding 50 g/L ) over and a coat primer consisting ofvolatile organic compounds less than 250g/L complete with all bye works at all locations and heights including corbelling/ moulding etc.with extra runners , using tape etc. to give a seamless look and as per drawings and manufacturers specifications and instruction ofEngineer Incharge.( Partition overall thickness 97mm with 70mm studs & 12.5 mm thick single layer Gypboard on both sides.) and verticalmembers shall be fixed to the RCC ceiling & floors

NOTE: Measurement shall be done for areas covered by boards

Providing & installing in position Eco-Friendly MDF board double skin partitions using' MDF board' manufactured from 100% renewable and sustainable wood resources from GREENPLY / Equivalent with 1.5 mm thk. lamination of approved shade,design andbrand, glued with Un-extended synthetic resin consisting of Volatile Organic compounds content not exceeding 30 g/l of approvedmake on both sides comprising of G.I metal stud concealed frame work, floor & ceiling channels, 12 mm thick MDF panels on both sidesfixed with necessary screws/bolts, drilling holes in ceiling, floor or walls fixing with anchor fasteners, applying jointing compound & finishingwith 1.5 mm thick laminate on both sides, cutting panels to required size, providing extra frame work around openings including 125 mmhigh matching skirting etc. and vertical members shall be fixed to the RCC ceiling & floors as per drawings and manufacturersspecifications and instruction of Engineer Incharge.

NOTE: Measurement shall be done for areas covered by boards

IW7Providing and fixing fixed glazing with 6 mm thk clear float glass with etching border design in gypsum board / MDF board partitionsalong with extra frame work with teak and teak wood beading as per the drawings and instructions of Engineer in charge.

SQM 20

IW8

Providing & fixing in position Frameless Glass partitions of 12 mm thickness toughened glass with approved etching designmanufactured to relevant I.S. codes from approved manufacturer including cost of providing necessary fittings,channels for holding theglass,approved sealants etc. as required all complete at all heights and as directed by the Engineer-in-Charge.

SQM 50

IW6

IW5

20SQM

SQM 160








1 2 3 4 5 6



Providing and fixing in position powder coated Aluminium glazed full height partitions with 6 mm thick clear toughened glass withapproved etching design manufactured to relevant I.S. codes from approved manufacturer and approved shade with horizontal aluminiummembers at floor level, sill level and false ceiling level and verticle members spacing at 1200 mm approx. including provision of extraextrusions for doors, glazing clips,required gaskets, approved sealants etc as required all complete at all heights and as directed by theEngineer-in-Charge.

NOTE: Measurement shall be done below the false ceiling area.

IW10

Supplying and installation of modular ergonomically designed work stations manufactured from Godrej interio REFLUX orequivalent;TYPE-I consisting of four workstations , each size 1500x1500 with laminated top as per drawing and with pedestal drawerunit, key board pull out tray, CPU trolley with castors, curvilinear tackable screen, modesty panel, concealed wire management withelectrical, LAN, telephone sockets, plastic grommet work surface, etc. complete, including all electrical works.

SET 4

IW11 TYPE-II same as FW-1 item but consisting of two workstations . SET 2

IW12

Supplying and installing a multi functional steel storage unit , frame type construction of size 1200mmX450mmX862.5mm(H) ofapproved shade with two adjustable shelves, top hung sliding doors with plastic rollers with steel ball bearing, adjustable levelers, snap ondie cast lock, wooden top etc. complete as per drawing and similar to M/S Godrej catalogue- VSDU-10 or equivalent.

nos 20

IW14Supplying and installing steel storage Tambour door unit of size 900mmX450mmX717mm (H) of approved shade.

nos 1

nos 1

Supplying and installing Training Table (double seater) of size 1500mmX600mmX680mm (H) laminated finish of approved shade withconcealed wire management facilities including switches on the mounting tray and access flap on the table top as per drawing and similarto M/S Godrej Catalogue 'Unlearn training table' or equivalent.

Supplying and installing Chief Manager's Table of size 2200mmX1190mmX750mm (H) laminated finish of approved shade with sidereturn unit with pedestal unit, mobile pedestal three drawer unit and cabinet partly glazed and partly panelled shutter of size2406mmX400mmX1215mm(H) as per drawing and similar to M/S Godrej catalogue 'NUMERO UNO' or equivalent.

Supplying and installing four drawer steel lateral filing cabinets with telescopic drawer slides mechanisms as per BLFMA standards, withanti-rebound and anti tipping mechanism, recess full length drawer pulls, wooden top finish as per drawing.

IW9

SQM 60

nos

nos 8

IW16

IW15

IW13

15








1 2 3 4 5 6



IW20Providing and fixing Vertical blinds 100 mm wide with wand control of approved shade and texture manufactured from Vista lavelor/Hunter Douglas or equivalent with all necessary arrangements reqired for the operation of blinds including head track, tilt rod,stopper etc atall heights as per drawing and instructions of engineer in charge SQM 100

IW21

Providing and fixing of Drapery rods for windows made of Top quality aluminium coated with scratch proof paints of approved shade anddesign at all heights as per drawing and instructions of engineer in charge

RM 75

SECTION TOTAL - IW

Supplying and installing Manager's Table of size 1800mmX900mm laminated finish of approved shade and side unit as per drawing andsimilar to M/S Godrej TRIDENT catalogue.

Supplying and installing modular Reception Table of curvilinear shape of size 2800mmX1430mm with approved shade laminated topchrome plated glass mountings, perforated modesty panel and glass counter with wire management facilities as per drawing.

IW17nos 6

IW18nos 1

IW19nos 1

Supplying and installing modular Secretary's table of approved laminated finish of size 1650mmX700mmX743mm(H) including twodrawers storage area and with side unit of size 1000mmX450mmX743mm(H) including storage area as per drawing.








1 2 3 4 5 6



C LANDSCAPING WORKS

LW-1

TreesDigging 600mm x 600 mm x 600 mm (2’x2’x2’) pits and refilling the same with red soil mixed with approved organic manure in the following percentage – 15% manure, 20% sand, 65% red soil by volume, and supplying and planting of best quality healthy trees of 1200 mmor at least one year old plants of various species. (Rate should include the cost of digging pit, refilling with above specifications and also supplying and planting of saplings. No separate rate to be quoted for digging of pits).

a)Royal Palms -Roystonea regia EACH 10b) Eucalyptus Globulus EACH 15c)Casurina sp EACH 15d) Indian Tulip Tree EACH 15e)Flame of Forest (Butea Monosperma) EACH 15f)Jacaranda mimosifolia EACH 5

LW-2

ShrubsSupplying and planting best quality pot grown healthy shrubs of different species of minimum 600 mm in ht., including the cultivation of shrub bed of 600mmdepth and 300mmdia. The soil mixture should be in the ratio of 15% manure, 40% red soil, 20% river sand, and 25% excavated earth. Rate to include cultivation of shrub bed as specified above.

EACHa)Bambusa vulgaris EACH 30b)Caesalphinia pulcherima EACH 10c)Acalypha godseffiana EACH 35d)Ageratum houstonianum EACH 30e)Anthurium andreanum EACH 20f)Bauhinia galpini EACH 20g)Duranta gold EACH 80

LW-3

Ground CoverPlanting of specified ground cover including cultivation of land to a depth of 300mm, clearing of debris and unwanted materials, and planting the same in a mixture of 15% manure, 40% red soil, 20% river sand, and 25% excavated earth. Rate to include cultivation of land as specified above. EACHa)Allamanda cathartica EACH 20b)Asparagus densiflorus 'Myers' EACH 30c)Lantana sellowiana (purple) EACH 30d)Ophiopogon jaburan EACH 15e)Tradescantia EACH 20

LW-4

LawnSupplying and planting of good quality nodes of specified grass for dibbling; including the cultivation of ground to a depth of 300 mm. (1 ft.)along with removal of all debris and other materials, and dibbling not more than 50 mm apart in a soil mixture of 15% manure, 25% fineriver sand, 35% red soil and 25% excavated earth and levelled to specified slopes. Rate to include cultivation of ground,soil,manure,riversand,red soil etc. as specified

SQMBermuda grass / Calcutta doob grass (Cynodon dactylon) 1600








1 2 3 4 5 6



LW-5

Pebbles:Providing and laying pebble stones of 20 to 40mmmm thick as called for, smooth ball milled white or coloured as approved to a depth of75mm thick loosely spread over a bed of C.C 1:4:8.Cost to include cost of transportation,C.C 1:4:8, laying complete as per drawing anddirections of the engineer - in - charge

SQM 50

Urns and Tubs:Providing, supplying and fixing in position reinforced cement tubs of either round ,square or rectangular in shape in specified areas as perdirection of the consultant / engineer -in -charge,painting the same in approved colour and make and filling the the same with good redearth of approved quality.Cost to include cost of transportation,red soil,fixing the tubs in 1:3 CM,labour complete.

RCC tubs of Size: 1m in dia and depth 0.6m nos 6RCC tubs of Size: 0.6m x 0.6m x 0.6m nos 25

SECTION TOTAL - LW

TOTAL AMOUNT ( A + B + C )

NOTE:The quantity indicated above is subject to variation. The unit price quoted for the items shall remain valid for any change in variation.





ENNORE TERMINAL PROJECT

Tenderer’s Signature with seal: Date:

SECTION-10 Page 32 of 32


SUMMARY OF CIVIL, ARCHITECTURAL, INTERIOR AND LANDSCAPING WORKS:

S.NO SECTION TITLE AMOUNT

A CIVIL AND ARCHITECTURAL WORKS 1 EW EARTHWORK

2 AT ANTITERMITE TREATMENT

3 CC PLAIN AND REINFORCED CONCRETE

4 MN MASONRY WORKS

5 FN PLASTERING & SURFACE FINISHES

6 FL FLOORING, PAVING & FACING

7 WW WOOD WORK

8 ST STEEL & IRON WORK

9 AL ALUMINIUM WORK

10 MS MISCELLANEOUS

11 SW SANITARY & WATER SUPPLY

SECTION TOTAL - A

B INTERIOR WORKS

C LANDSCAPING WORKS

T O T A L A M O U N T (A+B+C)

Item No. Item description Unit Qty.

Rate (in Rs.) (inclusive of all taxes & duties but excluding service tax)

Amount (in Rs.) (inclusive of all taxes & duties but excluding service tax)

( 4 x 5 )1 2 3 4 5 6

Design, Engineering, manufacture, procurement, supply, transportation, Receipt, storage,transportation to place of work, erection, testing & commissioning of followingequipments for illumination including supply of necessary consumable, hardwares &erection accessories as required based on specification, drawings and direction of siteengineer.

EL – 1 415/240V, 50Hz, 3 Phase / single phase and neutral,wall/recess mounted lighting / ACdistribution board having 1.6 mm thick epoxy powder coated sheet steel enclosure with IP-42 formounting MCCB's/MCB's/ELCB'S/Energy meter/Indication lamps etc.,as per specification /drawings, door with pad locking arrangement etc. complete with inter connection with not lessthan 10 sqmm copper(PVC sleeved) wire. The scope include necessary inter connecting of DB(Double earthing) upto earthsgrid using GI earth strips (25 x 6) mm, painting etc., as perspecification.

(a) Incomer : 100 A Four Pole MCCB with O/L, S/C & E/F Protection with Digital Energy MeterOutgoing: 63 A FP/TPN MCCB - 2 No 16 A TPN MCB - 9 Nos 20 A SP MCB - 6 Nos. 16/10 A SP MCB - 18 Nos.INSCRIPTION : LDB - ADMIN BUILDING - GROUND FLOOR. No. 1

(b) Incomer : 50 A Four Pole MCB with ELCB and Digital Energy MeterOutgoing: 16 A TPN MCB - 5 No


ENNORE TERMINAL PROJECTADMINISTRATIVE BUILDING (GREEN BUILDING)

PRICE SCHEDULE FOR ELECTRICS

Illumination



© 2010 MECON Limited All rights reserved MEC/23KM/T-04/10000028




20 A SP MCB - 9 Nos. 16/10 A SP MCB - 21 Nos.INSCRIPTION : SDB - ADMIN BUILDING - FIRST FLOOR. No. 1

(c) Incomer : 250A Four Pole MCCB with O/L, S/C & E/F Protection with Digital Energy MeterOutgoing : 160A TPN MCCB with O/L, S/C & E/F Protection - 2 NOS 63A TPN MCCB with O/L, S/C & E/F Protection - 3 NOS 32A TPN MCB - 3 NOS 16A SPN MCB - 18 NOSINSCRIPTION : ACPDB - 1 - ADMIN BUILDING - GROUND FLOOR. No. 1

(d) Incomer : 160A Four Pole MCCB with O/L, S/C & E/F Protection with Digital Energy MeterOutgoing : 125A TPN MCCB with O/L, S/C & E/F Protection - 3 NOS 32A TPN MCB - 3 NOS 16A SPN MCB - 21 NOSINSCRIPTION : ACPDB - 2 - ADMIN BUILDING - FIRST FLOOR. No. 1

EL – 2 LAWN / Road lighting luminaire suitable for 18W LED lamp shall have aluminium housing, clearflat, heat resistant glass at bottom, to suit to direct pole mounting from bottom 3.5 Mtr GI pipewith IP: 65 enclosure including including driver and all accessories fully wired up to full length ofGI pipe suitable for mounting the fittings with looping box.The looping box shall be made of 2mm thick GI sheet or FRP/GRP or Thermoplastic enclosures including necessary foundationand GI pipe inserts for looping cables. The scope of work excludes supply & laying of cables,Make shall be from the preffered makes list. similar to CGL type

a) LSTA181 - 18W LED with IP-65 (Direct pole mounting from bottom - 3.5 Mtr GI Pipe). No. 8







EL - 3 BOLLARDSDecorative die cast aluminium housing environment luminaire suitable for 18/20W CFL Lamp. Bollards shall be suitable for mounting on the base supplied with the luminaire. The enclosure shall be with IP:65 protection. Bollard version shall be provided with builin pole of suitable diameter including looping box, the looping box shall be made of 2 mm thick GI sheet or FRP/GRP or Thermoplastic enclosures, foundation, pipe inserts for cable loop in loop out and all accessories.The scope of work excludes supply & laying of cables, Make shall be from the preffered makes list, Similar to HAVELLS TYPEa) LHLC12120099 No. 25

EL – 4 Post top luminaire suitable for CFL (2 x11/18W) lamp with required control gear, ballast,capacitor, lantern etc.,including lamp , 2.5M G.I pipe with necessary foundation, looping box.Thelooping box shall be made of 2 mm thick GI sheet or FRP/GRP or Thermoplastic enclosures,etc., as per drawing, make shall be from the approved preffered list. The scope of work excludessupply & laying of cables, Make shall be from the preffered makes list, similar to Bajaj type

a) BJCPTI 218 OPAL No. 7

EL – 5 CHANDILIAR FITTINGDecorative Chandiliar suitable for fixing up to 18 number of CFL/LED with all necessary decorative suspension including lamps.Selection of Chandiliar shall be in consultation with client/consultant. Basic rate for supply of decorative chandiliar fitting shall be taken as Rs.25000. However the cost of luminaire will be adjusted based on the actual supply cost. No. 1

EL – 6 Recessed rotatable decorative fixture suitable for 2 x 8 W LED lamps with all accessoriesincluding lamp, Make shall be from the preffered makes listt. similar to CGL type a) LCDLS216 No. 8







EL – 7 Recess mounted TL-5 Fluorescent tube light decorative, mirrior optics luminaire with housing made up of CRCA sheet steel along with mounting rails & epoxy polyester powder coated, reflectors, Electronic ballast and lamps suitable for 4 x 14W / 2 x 28W- TL 5 Lamps , Make shall be from the preffered makes list. similar to Philips type

a) TBS 669/414 D6 HF No. 17b) TBS 669/228 D6 HF No. 12

EL – 8 Recess mounted LED down light luminaire suitable for 3 x 1W / 8x1W LED, including driver. Make shall be from the preffered makes list. similar to CGL typea) LCDO309R25WW No. 52b) LCDL108/WW No. 10

EL – 9 Recess mounted T-5 Fluorescent tube light, decorative, CAT2 Mirror optics luminaire with housing made up of CRCA MS sheet finished with epoxy powder coated with required electronic ballast and lamps suitable for 4 x 14 W / 2x14 W T5 FTL, Make shall be from the preffered makes list. similar to CGL type

a) T5CQ11414 EB No. 30b) T5CQ214 EB No. 40

EL – 10 Surface/Wall mounted T-5 Fluorescent tube light, decorative, serrated acrtlic diffuser luminaire with required electronic ballast and lamps suitable for 1 x 28W T5 FTL, Make shall be from the preffered makes list. similar to CGL type

a) T5LK1128 No. 34

EL – 11 Wall mounted Decorative type, Mini Mirror light fitting suitable for 1 x 11W CFL lamp withnecessary endcovers, control gear, lamp etc., , Make shall be from the preffered makes list.similar to CGL type a) TLN111/W No. 9







EL – 12 Decorative type Bulkhead fittings with engineering plastic housing, top frame with opal PMMAdiffuser etc., including lamp suitable for 1 x 13w CFL, Make shall be from the preffered makeslist. similar to CGL type

a) CBH13 No. 12

EL – 13 Surface mounted LED luminaire suitable for 9W LED, including driver. Make shall be from the preffered makes list. similar to CGL typea) LCDSP081 - 09/CDL No. 2

EL – 14 Noise less, Light weight, Rust proof Exhaust fan with single phase propeller type having fly birdmesh/louvers complete with mounting bracket, rubber pads of suitable thickness to absorbvibrations. etc. , Make shall be from the preffered makes list.

a) 250 MM sweep No. 7

EL – 15 650/1100V grade PVC insulated, unsheathed and unarmoured multistrand copper conductorcable (wire) of following equivalent conductor area including copper lugs as per specification,drawing and direction of site engineer, Make shall be from the preffered makes list.a) 1 X 6 Sqmm MTRS 50b) 1 x 4 Sqmm MTRS 50c) 1 x 2.5 Sqmm. MTRS 50







EL – 16 Supply, Erection, Testing & Commissioning of all materials for point wiring inclusive of circuitwiring using 2.5 Sq.mm PVC insulated copper wire with individual modular type/Decorative typecontrol switches/switch board etc., and point wiring with 1x1.5 Sq. mm PVC insulated copper wirein PVC heavy/medium gauge surface/ concealed conduits of required size laid on wall/ceilingwith single - core PVC insulated copper wire (for earthing the size of earthing cable shall be equalto that of circuit/point wiring.) The scope of work also includes Erection, Testing &Commissioning of MCB isolator, switches, sockets mounted in the switch board, MS switch box,necessary accssories like metal junction/pull boxes, ceiling roses, straight/slant brass battenholder etc., as per drg and all the connected work as per the specification and direction of siteengineer. All the points for tubelight fittings, decorative CFL wall mounted fittings and points forwhich no fittings are specified shall be terminated in a brass holder with CFL (Make shall be fromthe preffered makes list. Celo or cherry type control switches of anchor make or equivalent shall be provided) Wiring for following.

a) Light points controlled by one decorative type SP switch. No. 70b) Two /Three lights controlled by one decorative type switch No. 60c) Ceiling fan points controlled by decorative type switch and regulator (Electronic / Resistance type as approved by owner / consultant). No. 0

d) Staircase light point controlled by two-way staircase switch. No. 4e) 5 Pin 6A socket outlet with switch including socket mounted in Switch board. No. 30f) Decorative type 240V, 5 Pin 6A socket outlet with switch including socket mounted in separate sheet steel enclosure with plastic FRP face plate (Including cost of socket, switch & enclosure).

No. 46

g) Decorative type, 240V, 2 nos 5 pin 6A socket outlet with switch in separate sheet steel enclosure for computer points with plastic FRP face plate (Including cost of socket, switch & enclosure).

No. 35

h) Exhaust fan point controlled by one switch (circuit and point wiring to be carriedout using 2.5Sq.mm Cu.wire) No. 7







EL – 17 Supply, Erection, Testing & Commissioning of all materials for point wiring inclusive of circuitwiring using 4 Sq.mm PVC insulated copper wire in PVC Heavy/ Medium gauge for surface /concealed conduit laid on wall/ceiling along with PVC insulated copper wire (for earthing the sizeof earthing cable shall be equal to that of circuit/point wiring). The scope of work also includesErection, Testing & Commissioning of switches, MCBs Isolators and all the necessaryaccessories like Metal junction / pull box, MS mounting box etc., and all connected work forinstallation as per specification and direction of site engineer, Make shall be from the prefferedmakes list. Wiring for following.

a) Decorative type, 240V, 3 Pin, 16A OR 6 pin 6/16A, socket outlet with control switch & socket and plug top in sheet steel enclosure (Including cost of socket, switch & enclosure). No. 37

b) Air conditioners controlled by 32A/20A DP MCB - G' series (cost including DP MCB with Enclosure) No. 1

c) Air conditioners controlled by 63A/50A TPN MCB - G' Series (cost including TPN MCB with enclosure) No. 1

EL – 18 Presence / Occupancy sensor Supply, installation, testing and commissioning of Presence (Occupancy) sensors which includes automatic switching ON and OFF of light fittings with respect to occupants of the rooms and level of illumination control based on natural light for manager/incharge cabin rooms / work stations / conference room / multi purpose hall / corridors etc . The system shall include control of light fittings in group including necessary wiring up to light fitting / switches, and all accessories. Make shall be from the preffered makes list. Similar to L&T (Hager) typea) Dual lens - Up to 13 Meter covering diameter - EB812. SET. 21







EL – 19 GI pipe Class-B as per IS : 1239 threaded at both ends, with 80 microns Galvanising, coupling,suitable for concealed / surface laying, crossing of roads, or foundation without internal burrs.The scope include supply of all material for laying, including bending of the pipe whereverrequired, supporting saddles/brackets, supporting structures, etc., and supply of accessorieslike collers, tees, elbows, junction box / pull box/ceiling rose, consumables etc., for installation ofcomplete conduit system either concealed or surface laid or buried in floor & including necessarytrech work wherever required, as per specification, drawing and direction of site engineer, Makeshall be from the preffered makes list.

a) 80 MM dia. MTRS 10b) 65 MM dia. MTRS 10

EL – 20 Decorative type power socket/MCB in separate sheet steel enclsurea) 5/15 A sockets. No 5b) 32A DP MCB No 5

EL – 21 HOT-DIP galvanised iron / steel strip for lightning protection connecting to earthing pit /interconnection with earth mat of the shop etc., as per specification, drawing and direction of siteengineer, Make shall be from the preffered makes list.a) GI strip : (for Earthing Inter connection, Horizontal conductor, vertical down conductor) 1) 50 x 6 mm MTRS 50 2) 25 x 6 mm MTRS 50 3) 8.0 SWG GI wire MTRS 200

EL – 22 Air termination rods of 25 mm diameter of solid copper/Aluminium/GI , pointed at top withmounting plate 16 mm thick as per the drawing & direction site engineer.a) 1.2 M Long Nos 2







EL – 23 Heavy gauge PVC conduits with coupling at one end suitable for surface/concealed wiring without internal burrs with accessories like tees, bends,collers, clamps metal junction boxes terminals wherever required of following dia, Make shall be from the preffered makes list.a) 20 MM MTRS 10b) 25 MM MTRS 100c) 32 MM MTRS 20

EL - 24 Earthing pitEarth pit confirming to IS 3043 latest version, Supply, Installation, connection to lightning down conductor, testing and Commissioning of Earthing station, conforming to tender specn. and drawings inclusive of associated components materials like GI Pipe electrode (100 mm DIA GI Pipe) assembly, charcoal, salt, sand, bolt, nuts, washers, C.I or RCC lifting cover, and civil work involved in excavation, back filling and construction of brick chamber.

No. 2

4. All types of Light fixtures including slant / straight batten holder supplied with corresponding lamps.

3. Catalogue nos for various fittings have been indicated in the Bill of quantities. Specification of the equipments like material, painting and other provision etc shall meet the detials indicated by the manufacture for specific type

2. Length of down rods for Light fittings shall be considered based on the roof height.

Note :-1. The quantity indicated above is subject to variation. The unit price quoted for the items shall remain valid for any change in variation.

TOTAL





Rate (in Rs.) (inclusive of all taxes &

duties but excluding service tax)

Amount (in Rs.) (inclusive of all taxes &


( 4 x 5 )

1 2 3 4 5 6

1 Design, Engineering,Supply, inspection,testing, erection and commissioing of AC UNITS - Variable refregeration flow (VRF) Type with Cassette 4 way Indoor units , outdoor units comprising of semi hermetic / hermetic compressor, air cooled condenser, cooling coil & refrigrent circuits, refrigerent pipes, refrigerant pipe insulation, drain pipes,drain pipe insulation, refrigerent, blower unit with filters, hand held wireless remote control, Mounting arrangement for Indoor as well as outdoor units along with electrics, automation & control cabling and any other accessories required to complete the system, underdeck insulation for the A.C premises whereever roof exposed to sun as per Technical Specification.

1.1 Modular type VRF Out Door units (ODU) with Inverter scroll compressors, Condensor, Condensor fan, Accumulator, oil seperator, subcooler and other necessary accessories as per Technical Specification.

1.1.1 Capacity : 26.5 TR - 32 HP ODU No. 1Rerigerant piping with required supports and insulation Lot 1Drain piping with required supports and insulation Lot 1Y-Branches /Refrigerant pipe connectors No. 22

1.2 Indoor units (IDU) - Ceiling mounted 4 way Cassette type with electronic expansion valve to control the flow of refrigerent corresponding to load variations in the premises, multispeed fan motor, LCD type remote controller, drain pump & outlet connections as per the follwing capacities:-

Ground Floor1.2.1 Lobby - 2.0 TR -Ductable with diffuser and return air grill No. 11.2.2 Receiption -1.5TR No. 21.2.3 Work space-1.5TR No. 31.2.4 Doctor Room-1.5TR No. 11.2.5 PLT Manager Room-1.5TR No. 11.2.6 M&R Manager Room-1.5TR No. 1

First Floor

1.2.7 Multipurpose Hall-1.5TR No. 31.2.8 Work space-1.5TR No. 3

AIRCONDITIOING OF ADMIN.BUILDING

HINDUSTAN PETROLEUM CORPORATION LIMITED ENNORE TERMINAL PROJECT

PRICE SCHEDULE FOR AIRCONDITIONING OF ADMINISTRATIVE BUILDING









( 4 x 5 )

1 2 3 4 5 6AIRCONDITIOING OF ADMIN.BUILDING



1.2.9 Manager Operations-1.5TR No. 11.2.10 Manager Finance-1.5TR No. 11.2.11 Manager Purchase-1.5TR No. 11.2.12 CS -1.5TR No. 11.2.13 Waiting Hall-1.5TR No. 11.2.14 Chief Installation Manager-1.5 TR No. 21.2.15 Conference Hall -3TR No. 2

1.3 Supply and erection of roof under deck insulation XLPE foam (Chemically Crosslinked polyethylene foam) of 10mm thick as per technical specification wherever the roof of A/C prmises are exposed to Sun. Sq.m 300

2 Design, Engineering,Supply, inspection,testing, erection and commissioing of Precision Package Airconditioner of bottom air discharge Type with air cooled condenser out door unit. The package unit comprising of semi hermetic / hermetic digital scroll compressor, twin compressor circuit, cooling coil & refrigrent circuits, refrigerent pipes, refrigerant pipe insulation, drain pipe, first charge of refrigerent R410A/R407C,oil & lubricants, EC blower unit with EU4 filters, Mounting arrangement for Indoor as well as outdoor units along with electrics, controlpannel, automation & control cabling, humidity contro and any other accessories required to complete the system etc., of capacity 12TR (1W+1S) as per technical specification.

No 2

2.1 Supply and erection of annodised aluminum rectangular size 600 x 600mm diffusers with volume control dampers as per technical specification. No. 10

2.2 Supply and erection of Control room floor insulation XLPE foam (chemically Crosslinked polyethylene foam with aluminium foil on one face) of 9mm thick as per technical specification.

Sq-m 125

3 Supply and erection of independent Fresh air arrangment with Co2 sensor for Conference room and Multi Purpose Hall for monitoring the fresh air requirement. The Fresh air arrangment system of standard module of heat recovery ventilator type to modulate the temperature and humidity of incoming fresh air to match indoor conditions. Fresh air arrangment consists of high efficiency heat exchanger, bypass ventilation and filter section as per technical specification.









( 4 x 5 )

1 2 3 4 5 6AIRCONDITIOING OF ADMIN.BUILDING



3.1 Fresh air arrangment system for Conference Hall of capacity -210 CFM with supply and return air ducts, diffusers,grills. Set 1

3.2 Fresh air arrangment system for Multi purpose Hall of capacity -155 CFM with all supply and return air ducts,diffusers,grills. Set 1

3.3 Supply, erection and integration of CO2 sensor with fresh air arrangement along with motorised volume controlled damper for supplying the required air quantity into the premises as per technical specification.

Set 2

4 Fresh air arrangment system of standard module of heat recovery ventilator type to modulate the temperature and humidity of incoming fresh air to match indoor conditions . Fresh air arrangment consists of high efficiency heat exchanger, bypass ventilation and filter section with all supply and return air distribution system, diffusers, grills as per technical specification for ground floor and first floor of the building.

Ground floor

4.1 Fresh air unit 1 -capacity:280 cfm set 1


4.3 Fresh air unit 3 -capacity: 90 cfm set 1

First Floor4.4 Fresh air unit 4 -capacity:90 cfm set 1


4.6 Fresh air unit 6-capacity:170 cfm set 1


NOTE:The quantity indicated above is subject to variation. The unit price quoted for the items shall remain valid for any change in variation.

TOTAL




S.NO. DESCRIPTION

TOTAL AMOUNT (in Rs.)(inclusive of all taxes &


A) CIVIL AND ARCHITECTURAL WORKS

B) INTERIOR WORKS

C) LANDSCAPING WORKS

2 ILLUMINATION FOR ADMIN. BUILDING

3 AIRCONDITIOING FOR ADMIN. BUILDING

4 Total Rs.

SUMMARY OF PRICE SCHEDULE



1




section -10 cover page - hpcltenders.hpcl.co.in/tenders/tender_prog/tenderfiles/3460/notice... ·...

Documents